Mircom ALCN-792MISO/D Isolated Quad Loop Adder Module Owner's manual

ALCN-792MISO/D Isolated Quad Loop Adder Module
Mircom
Brand
Mircom
Model
ALCN-792MISO/D Isolated Quad Loop Adder Module
Category
Fire protection
Type
Owner's manual

Mircom ALCN-792MISO/D Isolated Quad Loop Adder Module expands your system capacity to 636 addressable devices on 2 loops, 159 per loop. With the addition of the ALCN-792D, this expands the module an additional 2 loops, bringing the module capacity to 1272 addressable devices. It has a dedicated Central Processor Unit (CPU) per module, providing reliable and efficient operation. Each loop controller module supports two fully loaded SLC lines, allowing up to 318 addressable devices per SLC line, for a total of up to 636 addressable devices per module.

Mircom ALCN-792MISO/D Isolated Quad Loop Adder Module expands your system capacity to 636 addressable devices on 2 loops, 159 per loop. With the addition of the ALCN-792D, this expands the module an additional 2 loops, bringing the module capacity to 1272 addressable devices. It has a dedicated Central Processor Unit (CPU) per module, providing reliable and efficient operation. Each loop controller module supports two fully loaded SLC lines, allowing up to 318 addressable devices per SLC line, for a total of up to 636 addressable devices per module.

Isolated Quad Loop Adder Module ALCN-792MISO/D
Mircom reserves the right to make changes at any time without notice in prices, colours, materials, components, equipment, specications and models and also to discontinue models.
5948
NOT TO BE USED FOR INSTALLATION PURPOSES.
CATALOG NUMBER
Description
The ALCN-792MISO Isolated Quad Loop Adder Module
provides two addressable loops plus an additional two
loops as part of the daughter board ALCN-792D which
is mounted over the ALCN-792MISO. The quad loop
adder module provides Signaling Line Circuits (SLC) to
the Flex-Net Addressable Fire Alarm system consisting
of 159 Sensors and 159 Addressable Modules per loop.
Each ALCN-792MISO Loop Controller Module has a
dedicated Central Processor Unit (CPU) and will support
two fully loaded SLC lines which will provide up to 318
addressable devices per SLC line, for a total of up to
636 addressable devices per ALCN-792MISO Quad
Loop Controller module.
The ALCN-792MISO occupies one module space on
any FleX-Net FX-2000N Series control panel chassis
The ALCN-792D daughter board provides two additional
SLC lines for up to 318 addressable devices per SLC
line, for a total of up to 1,272 addressable devices per
combination ALCN-792MISO with ALCN-792D.
Features
• Isolated
• Dedicated Central Processor Unit (CPU) per
module
• Expands system capacity to 636 addressable
devices on 2 loops, 159/159 per loop
• With the addition of the ALCN-792D this expands
module an additional 2 loops bringing module
capacity to 1272 addressable devices.
S7010 S7010
ALCN-792MISO
firealarmresources.com
Canada
25 Interchange Way
Vaughan, Ontario L4K 5W3
Telephone: (905) 660-4655
Fax: (905) 660-4113
Web page: http://www.mircom.com Email: [email protected]
Distributed by:
CAT. 5948
Rev.0
NOT TO BE USED FOR INSTALLATION PURPOSES.
U.S.A.
4575 Witmer Industrial Estates
Niagara Falls, NY 14305
Toll Free: (888) 660-4655
Fax Toll Free: (888) 660-4113
Model Description
ALCN-792MISO Isolated Quad Loop Adder Module
ALCN-792D Daughter Board
Ordering Information
Wiring Diagram
LOOP (3) LOOP (4)
P1 To Main Board
Connector P6
Four mounting holes (mount to
ALCN-792MISO board with screws
and spacers provided)
Connect ribbon cable
from this board to the
ALCN-792MISO board P6
+ - + - SS + - + -
BAA
B
COM (-)
JW2 - Normally set to
1-2, can be set to 2-3
to prevent noise from
CLIP System Sensor
sounder bases on
Loop 3
JW1 - Normally set to
1-2, can be set to 2-3
to prevent noise from
CLIP System Sensor
sounder bases on
Loop 4
SHIELD
+ - + - SS + - + -
ALARM OUT
BAA
B
COM (-)
LOOP 1LOOP 2
SHIELD
RS-485
P3
P2
P6
P1
ADDRESS
DIP SWITCH
Loop 1
Active LED
Loop 2
Active LED
Four shaded
mounting holes are
for Daughter board
ALCN-792D
Top 2 holes and
bottom 2 holes are
used for the ALCN-
792MISO Quad Loop
Adder module
mounting
DIP SWITCHES ARE FOR THIS
BOARD’S ADDRESS. SW1-1
IS THE LEAST SIGNIFICANT
DIGIT (BINARY). ACTIVE
POSITION IS ON.
P4
SW1
POWER CABLE
(OUT)
POWER CABLE
(IN)
JW2 - leave closed
JW1 - leave open
Green ashing
RS-485 heartbeat
LED
Green ashing
heartbeat LED for on
board processor
OUT
Daughter Board
Connector
RS-485
IN
USB PORT
(Factory use only)
JW4
JW3
JW6
8
1
NOT USED
EARTH
GROUND
ALCN-792MISO with ALCN-792D Electrical Specications
Power Limited: 24VDC, 400mA max, 10kHz frequency
Max loop resistance: 40 ohms
Current Consumption: Standby: 200mA
Alarm: 213 mA
Notes for ALCN-792MISO :
All circuits are power limited and must use type FPL, FPLR, or FPLP power limited cable.
Loop wiring: maximum loop resistance is 40 ohms total. These lines are power limited and fully supervised.
Refer to wiring instructions in the Network Fire Alarm Manual
firealarmresources.com
  • Page 1 1
  • Page 2 2

Mircom ALCN-792MISO/D Isolated Quad Loop Adder Module Owner's manual

ALCN-792MISO/D Isolated Quad Loop Adder Module
Mircom
Brand
Mircom
Model
ALCN-792MISO/D Isolated Quad Loop Adder Module
Category
Fire protection
Type
Owner's manual

Mircom ALCN-792MISO/D Isolated Quad Loop Adder Module expands your system capacity to 636 addressable devices on 2 loops, 159 per loop. With the addition of the ALCN-792D, this expands the module an additional 2 loops, bringing the module capacity to 1272 addressable devices. It has a dedicated Central Processor Unit (CPU) per module, providing reliable and efficient operation. Each loop controller module supports two fully loaded SLC lines, allowing up to 318 addressable devices per SLC line, for a total of up to 636 addressable devices per module.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI