Nissan T99K1 Virtual Key Kit User manual

AB C

D E F

G

BBB

1

Pick Up Coil - Required for reprogramming Virtual key to vehicle.

Air Coil - Required for reprogramming Virtual key to vehicle.

T99F6 4RA0A

T99K1 6TA04

1

Accessory Service Connector

Z

ADDITIONAL SERVICE PARTS NOT INCLUDED IN KIT ABOVE :

Service Part Number

KIT CONTENTS:

Item

Qty.

Part Description

AAA

CCC

1

APPLICATION:

DESCRIPTION:

T99F6 4RA0A , Accessory Service Connector - not included in kit above

GENUINE PARTS

INSTALLATION INSTRUCTIONS

PART NUMBER(S)

REQUIRED FOR

INSTALLATION:

Virtual Key Kit

T99K1 6TA01 Virtual Key

x3

x5

Carpet tape

89mm x 46mm

x5

Foam tape

60mm x 90mm

x2

AAA

BBB

CCC

ONLY FOR PROGRAMMING SERVICE PROCESS

20220926_T98K1 6GP1AxII_Z Page 1 of 37

For Firmware Update procedure please go to Appendix C / E.

For Reprogramming Procedure please go to Appendix G.

● Always follow the sequence of steps as they are shown, improper procedure can damage parts

and/or systems.

● Approved access to

TOOLS REQUIRED:

● Electrical tape

● Dealer certified iOS/Android

device (with KaaS Admin App).

F

Quick Reference Guide

3

Posi-Taps

Installation Instruction Website Address

E

2

● Posi-Tap™ instructions must be specifically followed as described in Appendix A.

Pick up coil - Not part of Virtual key kit, service part only

required for reprogramming virtual key.

Air coil - Not part of Virtual key kit, service part only required

for reprogramming virtual key.

BBB

1

CCC

1

T99K1 6TA04

SERVICE

● #2 Phillips Screw Driver

● Take care not to scratch or damage any component during the installation process.

● Trim Stick (Nylon)

● 10mm socket

G

1

● Be sure all key fobs for this vehicle have been acquired before proceeding.

● Avoid all other sources of frequency interference such as cell phones, walkie-talkies, radios, etc.

● Do not stop or disconnect CONSULT III plus or VI until after the process has been completed.

INSTALLATION CAUTIONS:

CAUTION

● Do not attach the Intelligent Key with a key holder that contains a magnet.

● Do not change or modify the Intelligent Key.

● Do not drop the Intelligent Key.

PART NUMBER(S)

REQUIRED FOR

INSTALLATION:

T99K1 6TA01, Virtual Key Kit

T99F6 4RA0A, Accessory Service Connector - not included in kit above

B

5

Wire ties

C

KIT CONTENTS:

Item

Qty.

Part Description

Service Part Number

A

1

Virtual Key device

5

3M Beta Tape 46 x 89mm

D

2

Foam Tape 90 x 60mm

● Consult Tool

Immobilizer PIN

● Do not allow the Intelligent Key, which contains electrical components, to come into contact with

water. This could severely affect system function. If the Intelligent Key gets wet, immediately

wipe moisture from I-Key until completely dry.

● Do not place the Intelligent Key in an area where temperatures exceed 140°F (60°C) for any

extended period of time.

● Do not strike the Intelligent Key sharply against another object.

● Take care not to scratch or damage any component during removal or re-installation process.

● Trim pieces found to have witness marks or broken clips ARE NOT to be reinstalled.

20220926_T98K1 6GP1AxII_Z Page 2 of 37

-

1.2)

VEHICLE

1.3)

D-OPT CONNECTOR LOCATION

1.1)

SYSTEM

System Block Diagram

SECTION

1

OVERVIEW

RCK Device

Dealer-Option

Connector Location

Please refer to Appendix B - Mechanization Drawing.

Wiring connection might vary from vehicle to vehicle.

RCK Device

DOP- Connector

20220926_T98K1 6GP1AxII_Z Page 3 of 37

-

a )

b )

c )

d )

e )

f )

a )

b )

a )

b )

c )

● If E.S.S. is not in Customer Mode, there will be a loss of normal vehicle operation, preventing

accessory function check.

Vehicle is delivered to customer

Customer (IN)

1

2

3

4

5

6

7

8

9

Place ignition in "ON" mode.

Transit (OUT)

Vehicle is being stored at the dealer

Transit (OUT)

SECTION

2

VEHICLE PREPARATION

CAUTION

● Always confirm the ignition is in the "OFF" position before changing the E.S.S. position.

Preset

10

Put shift lever in "P" position for A/T and CVT or

"1st" for M/T .

Condition

Switch Position

Note

Vehicle is delivered to the dealer

Place ignition in "OFF" mode.

2.1)

Check Extended Storage Switch Position.

Place ignition in "OFF" mode.

Apply park brake.

Locate Extended Storage Switch in cabin

fuse block as shown.

Confirm Extended Storage Switch is in

"Customer" (In/Engaged) position.

If ESS is not In/Engaged, then proceed to step

2.2 .

2.2)

Changing ESS Position.

To disengage Customer Mode, pull out in A

direction as shown.

To engage Customer Mode, press in B direction

as shown.

2.3)

Record Customer Presets.

Record the customer radio presets and other

presets as required.

20220926_T98K1 6GP1AxII_Z Page 4 of 37

-

a )

Disconnect battery terminal.

a )

b )

c )

d )

a )

2.6)

Harness preperation.

To prevent squeak and rattle, wrap label on

harness around harness and secure down

with tape.

2.4)

Move Seats.

● Allow an additional 3 min after key off with

doors closed for vehicle power to time out.

SECTION

2

VEHICLE PREPARATION

Move both front seats to full upward and

rearward position.

2.5)

Locate negative battery terminal.

Loosen nut with 10mm socket.

Lift negative battery terminal off stud.

Isolate negative battery terminal.

Before

After

Harness Label

Harness Label taped down

20220926_T98K1 6GP1AxII_Z Page 5 of 37

-

a )

b )

Remove LH Lower Kick Trim

SECTION

3

3.4)

Remove LH Lower Dash Side Trim

Locate LH and RH inner sill plate assembly.

Carefully pull Trim towards interior of vehicle

to unfasten Pawls, as shown.

Trim Fastener

Pawl

Lift sill plate up as shown to remove.

Locate LH Lower Dash Side Trim, as shown.

Use hand to twist and remove Trim Fastener.

Set aside for later reinstallation.

3.3)

TRIM REMOVAL

3.2)

Remove LH Lower Kick Trim

Using trim removal tool at forward end of kick

plate, pry kick plate up to disengage clips.

3.1)

Front of Vehicle

20220926_T98K1 6GP1AxII_Z Page 6 of 37

-

a )

b )

c )

Screw

Locate LH D-OPT Connector taped to main

harness bundle.

D-Opt Connector

Use #2 Philips screw driver to remove one

screw from bottom of Lower IP Trim.

Use trim removal tool to unfasten clips.

Carefully let Lower IP Trim hang down to the

floor.

Note: D-OPT Connector location might vary from

vehicle to vehicle.

SECTION

3

TRIM REMOVAL

3.6)

3.5)

Remove Lower IP Trim

Locate LH D-OPT Connector

20220926_T98K1 6GP1AxII_Z Page 7 of 37

-

a )

b )

c )

d )

a )

b )

c )

Search "KaaS Admin Tool" in either Apple or

Google Play Store.

OR

4.3)

Download KaaS Admin tool for Installation.

Either an Apple iPad or Samsung Galaxy Tab.

4.4)

Download KaaS Admin tool for Installation.

Once "KaaS Admin tool" is downloaded

proceed to Step 4.5.

Download and install the "KaaS Admin Tool"

app.

4.2)

Connect virtual key to RH D-opt connector.

4.1)

Re-connect battery terminal.

Using the Accessory service connector

connect virtual key device to the D-OPT

connector.

Using the procedure in Appendix B, connect

the red wire on the RCK Device to the red

wire on the ASC.

Using the procedure in Appendix B, connect

the black wire on the RCK Device to the black

wire on the ASC.

Using the procedure in Appendix B, connect

the white wire on the RCK Device to the white

wire on the ASC.

SECTION

4

PROGRAMMING PROCEDURE (Virtual key to Vehicle)

20220926_T98K1 6GP1AxII_Z Page 8 of 37

-

a )

If this is a new installation go to step 4.5, otherwise skip to reprogramming process (adding or

replacing keys) on appendix G.

Select setup access, as shown on left.

4.5)

Program Virtual key to Vehicle.

Note: Make sure to use the domain:

keycore-nissan.conti

Note: Make sure Sales and KaaS accounts are

under the same dealership.

For best reference, please refer to the videos located in Nissan Virtual Academy or INFINITI University

Online by clicking on the “Tech Training Garage Videos” link within the Service Technician view.

Select North America as region of sales.

4.7)

Program Virtual key to Vehicle.

4.6)

Program Virtual key to Vehicle.

To login in to KaaS Admin app, please use

the installer credentials sent to your

registered email address [NNA net user

profile] and select your dealership to

continue.

SECTION

4

PROGRAMMING PROCEDURE (Virtual key to Vehicle)

NOTE: KaaS Admin app should already be setup using dealer provided credentials.

Email

Password

keycore-nissan.conti

20220926_T98K1 6GP1AxII_Z Page 9 of 37

-

a )

b )

a ) Enter vehicle VIN.

b ) Enter vehicle MAKE.

c ) Enter vehicle MODEL.

d ) Enter vehicle YEAR.

e ) Press submit.

a )

b )

a )

b )

c )

Note: Number of questions will depend on the

vehicle model and year.

Select appropriate answer for each question.

Does key fob have a power liftgate button?

If "No" was selected proceed to next step,

otherwise go to step 4.13.

NOTE: Power Liftgate is only found in SUV

vehicles.

4.11)

Program Virtual key to Vehicle.

4.10)

Program Virtual key to Vehicle.

Program Virtual key to Vehicle - MANUAL

ENTRY.

Select appropriate answer, for each question.

Does key fob have remote engine start?

4.9)

4.8)

Program Virtual key to Vehicle - SCAN.

Select how to enter VIN, either enter

manually or SCAN using the tablet's camera.

If VIN was scanned, all vehicle information

will auto populate in appropriate fields. Go to

step 4.10.

TIP: To SCAN the VIN bar code, ensure iOS or

Android tablet camera has good visibility and

contrast. Glare reflection might cause camera to

not SCAN the VIN.

SECTION

4

PROGRAMMING PROCEDURE (Virtual key to Vehicle)

20220926_T98K1 6GP1AxII_Z Page 10 of 37

-

a )

b )

a )

b )

a )

b )

a )

Select the correct virtual key device, by

matching the Bluetooth signal name with

virtual key device number.

IMPORTANT: If Device Upgrade pops up go to

Appendix C - Automatic Process section

4.15)

Program Virtual key to Vehicle.

Select the "Scan device barcode" option

and scan the barcode on the virtual key

device using the tablet's camera and go to

step 4.16.

If this option doesn’t work go to step b).

Confirm Virtual key device is properly

connected.

Press ready.

4.13)

Program Virtual key to Vehicle.

Select the "Scan nearby Bluetooth

devices" and proceed to next step.

4.14)

Program Virtual key to Vehicle.

4.12)

Program Virtual key to Vehicle.

Select appropriate answer for each question.

Does the key fob have a trunk release

button?.

SECTION

4

PROGRAMMING PROCEDURE (Virtual key to Vehicle)

20220926_T98K1 6GP1AxII_Z Page 11 of 37

-

a )

b )

a )

b )

c )

Press and hold Start Button for at least

2 seconds without depressing brake to put

vehicle in Key On / Engine Off.

Connect CONSULT III plus tool to vehicle OBD

connector as shown.

Turn on hazard switch to prevent BCM from

entering into CAN communication sleep

mode.

NOTE: Programming process of the Virtual Key is the

same as key fobs.

4.19)

Connecting to the vehicle.

KaaS admin app will automatically go thru

preparation and key programming.

4.18)

Program Virtual key to Vehicle.

STOP and proceed to key programming with

consult tool. DO NOT CHECK THE "Key is

programmed" BOX

CAUTION

DO NOT CHECK THE BOX UNTIL VIRTUAL KEY

DEVICE HAS BEEN REGISTERED AS A THIRD KEY

FOB. IF YOU CHECK THE BOX BY ACCIDENT,

PLEASE UNCHECK IT BEFORE PROCEED TO THE

NEXT STEP.

Confirm the consult tool is correctly plugged

in, select the checkbox and press ready.

4.17)

Program Virtual key to Vehicle.

Wait for device to finish configuration.

4.16)

Program Virtual key to Vehicle.

SECTION

4

PROGRAMMING PROCEDURE (Virtual key to Vehicle)

!

20220926_T98K1 6GP1AxII_Z Page 12 of 37

-

a )

b )

a )

b )

a )

Wait until VI-2 firmware update is complete

as shown.

4.23)

Virtual key programming instructions.

Choose VI-2 detected as shown.

ChClick "Connect" as shown.

If VI has not connected to vehicle, click

"Select VI/MI" button to connect with

vehicle as shown.

4.22)

Virtual key programming instructions.

Start CONSULT III plus. Make sure VI is

connected. VI serial number will appear in VI

section and VI status will change to "Normal

Mode" (green color) as shown.

RES key fob programming instructions.

If VI is connected to vehicle go to step 4.24

and continue the installation. If VI is not

connected proceed to step 4.21.

SECTION

4

PROGRAMMING PROCEDURE (Virtual key to Vehicle)

4.20)

Virtual key programming instructions.

4.21)

20220926_T98K1 6GP1AxII_Z Page 13 of 37

-

a )

b )

c )

a )

Once you click "Confirm" you will see a

system call menu as shown.

4.27)

Virtual key programming instructions.

Click "Automatic Selection" as shown.

4.26)

Virtual key programming instructions.

Review the information on the confirmation

screen. If correct, click "Confirm" as shown.

CONSULT III plus will change to the home

screen automatically when the procedure is

complete and VI-2 is connected as shown.

4.25)

Virtual key programming instructions.

4.24)

Virtual key programming instructions.

Click "Diagnosis (All Systems)" as shown.

Wait for systems diagnosis process to

complete.

SECTION

4

PROGRAMMING PROCEDURE (Virtual key to Vehicle)

20220926_T98K1 6GP1AxII_Z Page 14 of 37

-

a )

b )

a )

a ) A precaution screen will appear.

b )

a )

Click "Automatic Selection" as shown.

4.31)

Virtual key programming instructions.

Click "Immobilizer" as shown.

4.30)

Virtual key programming instructions.

NOTE: If during the installation an error occurs

with the Consult tool, the Virtual Key device

requires to be reset, please refer to Appendix F

section for RESET process.

After you have finished reading all the

precautions, click "Next" as shown.

Verify there are no DTCs, and click "Erase"

button. Follow the prompts which follow.

After deleting DTCs, click the "Home" button

at the top left of the screen as shown.

4.29)

Virtual key programming instructions.

4.28)

Virtual key programming instructions.

SECTION

4

PROGRAMMING PROCEDURE (Virtual key to Vehicle)

Home Button

20220926_T98K1 6GP1AxII_Z Page 15 of 37

-

a )

4.35)

Virtual key programming instructions.

Once you click "When performing key

registration" a new Contents of Operation

selection "Register Key" will be available as

shown.

Under Contents of Operations selection, click

"Register Key" as shown.

NOTE: To register virtual key is same process as

registering key fob. By holding the device near

push start switch till registration is complete.

Once you click "Confirm", you will see a

system call menu as shown.

4.34)

Virtual key programming instructions.

Once the system call is complete, you will

enter the Select Operation screen as shown.

Under OPERATION CATEGORY menu, click

"When performing key registration" as

shown.

Review the information on the confirmation

screen. If correct, click "Confirm" as shown.

4.33)

Virtual key programming instructions.

4.32)

Virtual key programming instructions.

SECTION

4

PROGRAMMING PROCEDURE (Virtual key to Vehicle)

20220926_T98K1 6GP1AxII_Z Page 16 of 37

-

a )

b )

a )

Check the "Key is programmed" box once

virtual key has been programmed to the

vehicle using consult tool.

4.39)

Virtual key programming instructions.

NOTE: If error message is displayed after this

step, please retry the Virtual Key device

programming.

From outside the vehicle press Lock on Fob 2

and Unlock on Fob 1 and confirm the vehicle

responds accordingly as shown in left.

4.38)

Virtual key programming instructions.

Place the front square bump of the virtual key

device against the engine start button for it to

be programmed to the vehicle.

NOTE: If during this step the Virtual Key Device is

not recognized, please refer to Appendix F section

to RESET the device.

From outside the vehicle press Lock on Fob 1

and Unlock on Fob 2 and confirm the vehicle

responds accordingly as shown in left.

4.37)

Virtual key programming instructions.

SECTION

4

PROGRAMMING PROCEDURE (Virtual key to Vehicle)

4.36)

Virtual key programming instructions.

Follow the CONSULT III plus prompts as

shown.

20220926_T98K1 6GP1AxII_Z Page 17 of 37

-

a )

b )

a )

If there was no "Device Upgrade" message on

step 4.15, go to Appendix E and perform the

Firmware Update - Manual Process.

NOTE: Provisioning virtual key to the vehicle has

been completed.

Confirm installation report is complete, press

"OK" to return to main screen.

4.42)

Virtual key programming instructions.

4.41)

Virtual key programming instructions.

Verify all vehicle functions in the KaaS admin

app and press DONE once verified.

NOTE: Ensure hazard lights are turned off, key

fobs are outside the vehicle and doors are closed

before perform functional test.

TIP: Perform Vehicle functions in such order:

1) Unlock

2) Lock

3) Remote Engine Stop

4) Trunk release or Trunk lift gate open/close.

5) Panic

6) Enable engine start button (To be authorized to start

vehicle).

7) Disable engine start button (Vehicle will not start,

"no key detected" message will be displayed on

Instrument Cluster).

8) If one of the functions fails during this step,

please retry. If the problem persist, please call to

the support line phone number indicated in the

quick reference guide.

9) If all functions have been validated with no concern,

proceed to next step.

SECTION

4

PROGRAMMING PROCEDURE (Virtual key to Vehicle)

4.40)

Virtual key programming instructions.

Key programming has been completed with

Consult tool.

KaaS admin app will go thru Synchronization,

Calibration, and Verification.

20220926_T98K1 6GP1AxII_Z Page 18 of 37

-

a )

b )

c )

a )

b )

a )

b )

a )

b )

5.3)

Carefully coil excess wire harness into bundle

as shown. Tighten bundle with a cable tie.

Wrap a piece of foam tape around Posi-tap

connections as shown.

Route Virtual key device harness to the (LH)

Accessory Service Connector.

5.4)

Route and bundle harness

Secure the virtual key device harness to the

vehicle harness bundle with a zip tie as shown

on the left

Tuck wire harness bundle into the area behind

the lower kick trim.

Carefully remove the lining from double sided

tape on back of Virtual key device.

Route Wire Harness

5.2)

Install Virtual Key Device

5.1)

Virtual key Device Installation

Locate flat spot in the area behind the lower

IP Panel, metal surface.

Wipe back of finisher area clean of any dirt

using alcohol/water solution on a soft non-

linting cloth.

Let dry for 30 seconds.

Press and hold firmly on virtual key device to

attach to carpet floor, apply 15lbs of pressure

for 30 seconds.

SECTION

5

INSTALLATION PROCEDURE (Virtual Key Device)

VIRTUAL KEY DEVICE

Front of Vehicle

Zip Tie

Harness routing

Front of Vehicle

20220926_T98K1 6GP1AxII_Z Page 19 of 37

-

a )

b )

a )

b )

a )

b )

c )

a )

b )

c )

Check terms and conditions box.

Press create new account.

NOTE: For security purposes, Virtual key app is

equipped with double password verification,

customer will need to access the email address

they provided to retrieve the confirmation code.

Create Virtual key account.

Have customer search "Nissan Virtual key",

on their smartphone device in either Apple or

Google Play Store.

Download and install Nissan Virtual key app.

If customer already has an existing account

have them sign-in using their credentials

(email address and password) and go to step

6.4.

Have customer enter all the required

information to sign up for account: Name,

Email, Mobile Phone, and Password.

6.1)

Download/Install Virtual key app.

SECTION

6

TRANSFER VIRTUAL key to Customer (Sales to Customer)

If customer does not have an account, have

them sign up for a new virtual key account.

Go to next step.

6.4)

Receive vehicle.

6.3)

Create Virtual key account.

After logging in, have customer go to

settings.

6.2)

Customer Account

20220926_T98K1 6GP1AxII_Z Page 20 of 37

Page is loading ...