Astria Fireplaces VR(C)T30 Instruction Sheet

Brand: Astria Fireplaces

Model: VR(C)T30

Type: Instruction Sheet

This manual is also suitable for

Figure 1 - Assembling Trim

Figure 2 - Attaching Trim to Firebox

6. While ﬁ rmly holding edges of trim together, tighten both screws

on the adjusting plate using a slotted screwdriver.

7. Repeat steps 2 through 6 for other side.

8. Place the assembled trim onto ﬁ rebox cabinet. Align hanging

notches on trim with trim hanging shoulder screws (see Figure

2). Tap trim ﬁ rmly into place with palm of hand or rubber mallet

by engaging hanging notches around shoulder screws. Start at

one end of the trim and work around ﬁ rebox until all notches are

fully engaged.

Set Screws

Slot

Shim

Top Trim

Side Trim

Adjusting

Plate

Mitered

Edge

Mitered Edge

PT SERIES PERIMETER TRIM KITS

[FOR USE WITH MODELS BRT2032, BRT2532/36, BRT4036/42, BRT4336/42, BRT4536/42, VRT3032/36/42, VCT3032/36/42, VRT4032/36, VCT4032/36, ALPHA32/36,

MISSION36/42, VEGA32/36/42, CUMBERLAND32/36/42, WESTERLY32]

PT SERIES PERIMETER TRIM KITS

P/N 127149-01

Rev. B, 03/2017

HEARTH PRODUCTS

KITS AND ACCESSORIES

Cat. No. Model Description

F1039

PT32

32" Perimeter Trim - Black

F1040

PT32B

32" Perimeter Trim - Brushed Brass

F1041

PT32P

32" Perimeter Trim - Platinum

F1042

PT36

36" Perimeter Trim - Black

F1043

PT36B

36" Perimeter Trim - Brushed Brass

F1044

PT36P

36" Perimeter Trim - Platinum

F1045

PT42

42" Perimeter Trim Kit, Black

F1046

PT42B

42" Perimeter Trim Kit, Brushed Brass

F1047

PT42P

42" Perimeter Trim Kit, Platinum

KIT CONTENTS

1 ea. 3-Piece Trim Set

1 ea. Hardware Kit

1 ea. Instruction Sheet

REQUIRED TOOLS AND SUPPLIES

Flat Blade Screwdriver

GENERAL INFORMATION

3-piece perimeter trim kits are available in black, brushed brass

and platinum ﬁ nishes.

READ ALL THE STEPS BEFORE STARTING THE INSTALLATION

THE FIREPLACE MUST BE OFF AND COLD BEFORE BEGINNING.

ALL WARNINGS, PRECAUTIONS AND INSTRUCTIONS IN THE

INSTALLATION AND OPERATION MANUAL PROVIDED WITH THE

APPLIANCE APPLY TO THESE INSTRUCTIONS.

If you encounter any problems, need clariﬁ cation of these instructions

or are not qualiﬁ ed to properly install this kit, contact you local

distributor or dealer.

If any of these parts are missing or damaged, contact your dealer or

IHP.us.com for referral information.

INSTALLATION INSTRUCTIONS

NOTE: Firebox model may vary from that shown in Figure 2.

1. Remove packaging from three pieces of trim.

2. Locate the two adjusting plates with set screws and two shims

in the hardware packet.

3. Align shim under adjusting plate as shown in Figure 1.

4. Slide one end of adjusting plate/shim in slot on mitered edge of

top trim (see Figure 1).

5. Slide other end of adjusting plate/shim in slot on mitered edge

of side trim (see Figure 1).

Trim Hanging Shoulder

Screw Locations

Assembled Trim

Hanging Notches

on Trim

P/N 127149-01 Rev. B 03/2017

IHP reserves the right to make changes at any time, without notice, in design, materials, speciﬁ cations, prices and also to discontinue colors, styles and products. Consult your local distributor for

ﬁ replace code information. IHP

1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

IHP.us.com 1

PT32, PT36 Y PT42 SERIES

DE JUEGO DE ADORNO INSTRUCCIONES DE INSTALACIÓN

INCLUYE PAQUETE DE FERRETERÍA 102865-01

Figura 1 - Armado del adorno

INSTRUCIONES DE INSTALACI

Nota: El modelo de chimenea puede ser distinto al ilustrado en la

Figura 2.

1. Retire el embalaje de las tres piezas de adorno.

2. Localice las dos placas de ajuste con su juego de tornillos, y dos

bases para nivelar en el paquete de piezas.

3. Alinee la base para nivelar debajo de la placa de ajuste como se

muestra en la Figura 1.

4. Deslice un extremo de la placa de ajuste y base para nivelar en

la ranura del borde angular de la parte superior del adorno de la

chimenea (consulte la ﬁ gura 1).

5. Deslice el otro extremo de la placa de ajuste y base para nivelar en

la ranura del borde angular del adorno de la chimenea (consulte

la ﬁ gura 1).

Figura 2 - Colcación del adorno en la chimenea

6. Mientras sostiene ﬁ rmemente los bordes del adorno juntos,

apriete los dos tornillos de la placa de ajuste con un destornil-

lador plano.

7. Repita los pasos 2 a 6 para armar el otro lado.

8. Ponga el ensamblaje del adorno en el gabinete de la chimenea.

Alinee las muescas del adorno con los tornillos con pivote pro-

vistos para colgar el adorno (consulte la ﬁ gura 2). Fije el adorno

dándole unos lijeros golpes con la palma de la mano o con

un mazo de goma, hasta que las muescas hayan entrado

completamente en los tornillos con pivote. Empiece en un

extremo del adorno y continúe alrededor de la chimenea hasta

que todas las muescas estén ocupadas completamente.

Tornillos de

presión

Ranura

Base para

nivelar

Parte superior

del adorno

Lado del

adorno

Placa de

ajuste

Borde angular Borde

angular

Si alguna pieza falta o está dañada, llame al proveedor que le vendió

este paquete o a IHP. También puede puede visitar el sitio web de

servicio técnico de IHP en IHP.us.com.

Ubicación de

los tornillos con

pivote

Muescas para

colgar el adorno

Adorno armado