2. Biamp
  3. NPX Replacement Part Kits

Biamp NPX Replacement Part Kits Installation guide

  • Hello, I'm your chat assistant. I have reviewed the installation guide for the Biamp Wall-Mount Bracket, Base Foot, Gooseneck Microphone, and Handheld Microphone. This document provides instructions on how to replace parts for NPX Paging Stations. I can answer questions about the suggested tools, step-by-step procedures, and component-specific instructions. Please feel free to ask.
  • What tools are suggested for the replacement?
    How do I detach the foot from the NPX base?
    How are microphones removed from the NPX?
    Are rubber adhesive pads reusable after back cover removal?
[email protected] support.biamp.com
NPX PART REPLACEMENT KITS
INSTALLATION GUIDE
Models
Wall-Mount Bracket
Base Foot
Gooseneck Microphone
Handheld Microphone
This guide presents step-by-step instructions to replace the wall bracket, base foot, and gooseneck
and handheld microphones for NPX Paging Stations.
SUGGESTED TOOLS
• Release tool or small Phillips screwdriver (maximum 3/16” 4.7 mm
diameter)
• TR-10 Allen wrench
• Magnetic screwdriver or magnet to extract the screws (optional)
• Wrench or socket wrench (for Gooseneck only)
2NPX Replacement Part Kits Installation Guide
FOOT REPLACEMENT
2. Press and hold the tool in the hole and slide the foot to the left and lift it away from the unit.
1. Detach the foot from the NPX base by inserting a small Phillips screwdriver or similar tool, with a
maximum diameter of 3/16” (4.7mm), into the hole.
3. Reverse the previous instructions to install the new foot. Ensure it is secure by listening for a click.
HANDHELD & GOOSENECK
3
NPX Replacement Part Kits Installation Guide
WALL-MOUNT BRACKET REPLACEMENT
1. Use instructions from previous page to remove the foot from the NPX base. Slide the mounting
plate located at the back of the unit to the left and lift it away from the device.
2. Reverse the previous instructions to install the new back plate.
HANDHELD & GOOSENECK
4NPX Replacement Part Kits Installation Guide
BACK COVER REMOVAL
2. Remove the 4 screws with a TR-10 Allen wrench.
NOTE: Use a magnetic screwdriver or magnet to more easily extract the screws.
1. Gently peel back a corner of each of the 4 rubber adhesive pads at the back of the unit to expose
the screws beneath (peeling back just the corner allows for reuse of the pads).
HANDHELD & GOOSENECK
5
NPX Replacement Part Kits Installation Guide
3. Gently pry the back and front apart by starting at the corner of the unit near the Kensington lock
slot.
4. After creating a small opening, carefully run a tool or your nger along the seam to gradually
separate the parts completely.
5. Follow the handheld or gooseneck microphone installation instructions starting on page 6.
BACK COVER REMOVAL CONTINUED
HANDHELD & GOOSENECK
6NPX Replacement Part Kits Installation Guide
1. Disconnect the microphone plug from the connector.
2. Lift the cord from the holder.
3. Extract the microphone and associated wiring by pulling the cord through the hole.
MICROPHONE REMOVAL
Cord Holder
HANDHELD
7
NPX Replacement Part Kits Installation Guide
MICROPHONE INSTALLATION
HANDHELD
1. Thread the cord back through the hole and rmly press it down into the holder.
2. Insert the cord plug it into the connector.
Cord Holder
8NPX Replacement Part Kits Installation Guide
3. Align the RJ-45 port with the corresponding hole, then lower the back onto the front of the unit.
4. Tighten the 4 screws at the back cover.
5. Replace the rubber adhesive pads to cover the screws.
6. Reverse the previous instructions to install the new foot, and ensure it is secure by listening for a
click.
MICROPHONE INSTALLATION CONTINUED
HANDHELD
RJ-45 hole
RJ-45 Port
9
NPX Replacement Part Kits Installation Guide
MICROPHONE REMOVAL
GOOSENECK
1. Unplug the microphone cord from the connector.
2. Use a wrench or socket wrench to unscrew the 11/16” (17mm) nut from the base of the unit. Set
aside until the replacement microphone is ready to be installed.
10 NPX Replacement Part Kits Installation Guide
MICROPHONE REMOVAL CONTINUED
GOOSENECK
3. Remove the microphone by pulling the stem and associated wiring through the hole.
NOTE: Do not remove the grounding wire positioned under the microphone nut.
11
NPX Replacement Part Kits Installation Guide
MICROPHONE INSTALLATION
1. Install the new microphone by threading the associated wire and microphone stem through the
hole, ensuring it passes through the grounding loop.
2. Securely tighten the nut onto the microphone stem until it ts snugly. Avoid over-tightening.
GOOSENECK
12 NPX Replacement Part Kits Installation Guide
3. Insert the cord plug it into the connector.
4. Align the RJ-45 port with the corresponding hole, then lower the back onto the front of the unit.
5. Tighten the 4 screws at the back cover.
6. Replace the rubber adhesive pads to cover the screws.
7. Reverse the previous instructions to install the new foot, and ensure it is secure by listening for a
click.
RJ-45 hole
RJ-45 Port
MICROPHONE INSTALLATION CONTINUED
GOOSENECK
[email protected] support.biamp.com
CONTACT US
Email: [email protected]
Web: support.biamp.com
Warranty: biamp.com/legal/warranty-information
Safety & Compliance: biamp.com/compliance
26JUN23
/