ONKYO HT-RC260 User manual

AV Receiver

HT-RC260

Instruction Manual

Thank you for purchasing an Onkyo AV Receiver.

Please read this manual thoroughly before making

connections and plugging in the unit.

Following the instructions in this manual will enable

you to obtain optimum performance and listening

enjoyment from your new AV Receiver.

Please retain this manual for future reference.

Contents

Introduction ...................................2

Connections.................................11

Turning On & Basic Operations

......19

Advanced Operations .................33

Controlling iPod & Other

Components............................51

Others...........................................59

E

n

2

En

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with the cart, stand,

tripod, bracket, or table speci-

fied by the manufacturer, or

sold with the apparatus. When

a cart is used, use caution

when moving the cart/appara-

tus combination to avoid

injury from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualified service personnel. Ser-

vicing is required when the apparatus has been dam-

aged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or has

been dropped.

15. Damage Requiring Service

Unplug the apparatus from the wall outlet and refer

servicing to qualified service personnel under the fol-

lowing conditions:

A. When the power-supply cord or plug is damaged,

B. If liquid has been spilled, or objects have fallen

into the apparatus,

C. If the apparatus has been exposed to rain or water,

D. If the apparatus does not operate normally by fol-

lowing the operating instructions. Adjust only

those controls that are covered by the operating

instructions as an improper adjustment of other

controls may result in damage and will often

require extensive work by a qualified technician to

restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in

any way, and

F. When the apparatus exhibits a distinct change in

performance this indicates a need for service.

16. Object and Liquid Entry

Never push objects of any kind into the apparatus

through openings as they may touch dangerous volt-

age points or short-out parts that could result in a fire

or electric shock.

The apparatus shall not be exposed to dripping or

splashing and no objects filled with liquids, such as

vases shall be placed on the apparatus.

Don’t put candles or other burning objects on top of

this unit.

17. Batteries

Always consider the environmental issues and follow

local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation,

such as a bookcase or rack, ensure that there is ade-

quate ventilation.

Leave 20 cm (8") of free space at the top and sides and

10 cm (4") at the rear. The rear edge of the shelf or

board above the apparatus shall be set 10 cm (4")

away from the rear panel or wall, creating a flue-like

gap for warm air to escape.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPARATUS TO

RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RISQUE DE CHOC ELECTRIQUE

NE PAS

OUVRIR

AVIS

PORTABLE CART WARNIN

G

S3125A

3

En

Precautions

1. Recording Copyright—Unless it’s for personal use

only, recording copyrighted material is illegal without

the permission of the copyright holder.

2. AC Fuse—The AC fuse inside the unit is not user-ser-

viceable. If you cannot turn on the unit, contact your

Onkyo dealer.

3. Care—Occasionally you should dust the unit all over

with a soft cloth. For stubborn stains, use a soft cloth

dampened with a weak solution of mild detergent and

water. Dry the unit immediately afterwards with a

clean cloth. Don’t use abrasive cloths, thinners, alco-

hol, or other chemical solvents, because they may

damage the finish or remove the panel lettering.

4. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE

FIRST TIME, READ THE FOLLOWING SECTION

CAREFULLY.

AC outlet voltages vary from country to country.

Make sure that the voltage in your area meets the volt-

age requirements printed on the unit’s rear panel (e.g.,

AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit

from the AC power source. Make sure that the plug is

readily operable (easily accessible) at all times.

Pressing ON/STANDBY to select Standby mode does

not fully shutdown the unit. If you do not intend to use

the unit for an extended period, remove the power cord

from the AC outlet.

5. Preventing Hearing Loss

Caution

Excessive sound pressure from earphones and head-

phones can cause hearing loss.

6. Batteries and Heat Exposure

Warning

Batteries (battery pack or batteries installed) shall not

be exposed to excessive heat as sunshine, fire or the

like.

7. Never Touch this Unit with Wet Hands—Never han-

dle this unit or its power cord while your hands are

wet or damp. If water or any other liquid gets inside

this unit, have it checked by your Onkyo dealer.

8. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you originally

bought it.

• Do not leave rubber or plastic items on this unit for

a long time, because they may leave marks on the

case.

• This unit’s top and rear panels may get warm after

prolonged use. This is normal.

• If you do not use this unit for a long time, it may not

work properly the next time you turn it on, so be

sure to use it occasionally.

For U.S. models

FCC Information for User

CAUTION:

The user changes or modifications not expressly approved

by the party responsible for compliance could void the

user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation.

This equipment generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee

that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio

or television reception, which can be determined by turn-

ing the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit differ-

ent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV techni-

cian for help.

For Canadian Models

NOTE: THIS CLASS B DIGITAL APPARATUS COM-

PLIES WITH CANADIAN ICES-003.

For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT,

FULLY INSERT.

Modèle pour les Canadien

REMARQUE: CET APPAREIL NUMÉRIQUE DE

LA CLASSE B EST CONFORME À LA NORME NMB-

003 DU CANADA.

Sur les modèles dont la fiche est polarisée:

ATTENTION: POUR ÉVITER LES CHOCS ÉLEC-

TRIQUES, INTRODUIRE LA LAME LA PLUS LARGE

DE LA FICHE DANS LA BORNE CORRESPON-

DANTE DE LA PRISE ET POUSSER JUSQU’AU

FOND.

4

En

Supplied Accessories

Make sure you have the following accessories:

*

In catalogs and on packaging, the letter at the end of the prod-

uct name indicates the color. Specifications and operations are

the same regardless of color.

Installing the Batteries

Note

• If the remote controller

doesn’t work reliably, try

replacing the batteries.

• Don’t mix new and old

batteries or different

types of batteries.

• If you intend not to use

the remote controller for

a long time, remove the batteries to prevent damage from leak-

age or corrosion.

• Remove expired batteries as soon as possible to prevent damage

from leakage or corrosion.

Aiming the Remote Controller

To use the remote controller, point it at the AV receiver’s

remote control sensor, as shown below.

Indoor FM antenna (➔ 17)

AM loop antenna (➔ 17)

Speaker cable labels (➔ 11)

Speaker setup microphone (➔ 23)

Remote controller and two batteries (AA/R6)

Using the Remote Controller

Batteries (AA/R6)

Remote control sensor

AV receiver

Approx. 16 ft. (5 m)

5

En

Contents

Important Safety Instructions ......................................... 2

Precautions....................................................................... 3

Supplied Accessories...................................................... 4

Using the Remote Controller .......................................... 4

Features ............................................................................ 6

Front & Rear Panels......................................................... 7

Front Panel..................................................................... 7

Display............................................................................ 8

Rear Panel ..................................................................... 8

Remote Controller............................................................ 9

Controlling the AV Receiver ........................................... 9

About Home Theater...................................................... 10

Enjoying Home Theater................................................ 10

Connecting the AV Receiver ......................................... 11

Connecting Your Speakers .......................................... 11

About AV Connections ................................................. 14

Connecting Components with HDMI ............................ 15

Connecting External Components................................ 16

Connecting Onkyo Components ............................ 17

Connecting Antenna..................................................... 17

Which Connections Should I Use?............................... 18

Turning On/Off the AV Receiver ................................... 19

Turning On ................................................................... 19

Turning Off ................................................................... 19

Basic Operations............................................................ 20

Selecting the Language Used for the Onscreen

Setup Menus.............................................................. 20

Playing the Connected Component.............................. 20

Displaying Source Information ..................................... 20

Setting the Display Brightness ..................................... 20

Muting the AV Receiver................................................ 21

Using the Sleep Timer.................................................. 21

Selecting Speaker Layout ............................................ 21

Using the Audio and Video Menus ............................... 21

Changing the Input Display .......................................... 22

Using Headphones....................................................... 22

Audyssey 2EQ

®

Room Correction

and Speaker Setup .................................................... 22

Listening to the Radio ................................................... 25

Using the Tuner............................................................ 25

Presetting FM/AM Stations........................................... 26

Recording ....................................................................... 27

Using the Listening Modes ........................................... 28

Selecting Listening Modes ........................................... 28

About Listening Modes................................................. 29

Advanced Setup ............................................................. 33

On-screen Setup Menus...............................................33

Common Procedures in Setup Menu ........................... 33

Input/Output Assign ...................................................... 34

Speaker Setup..............................................................35

Audio Adjust ................................................................. 37

Source Setup................................................................39

Listening Mode Preset..................................................43

Miscellaneous...............................................................43

Hardware Setup............................................................ 44

Lock Setup....................................................................45

Using the Audio Settings .............................................. 45

Adjusting the Bass & Treble ......................................... 47

Zone 2.............................................................................. 48

Connecting Zone 2 .......................................................48

Setting the Powered Zone 2 ......................................... 49

Using Zone 2 ................................................................ 49

Controlling iPod .............................................................51

Connecting an Onkyo Dock..........................................51

Using the Onkyo Dock..................................................52

Controlling Your iPod.................................................... 53

Controlling Other Components.....................................55

Preprogrammed Remote Control Codes ......................55

Looking up for Remote Control Code ...........................55

Entering Remote Control Codes...................................56

Remote Control Codes for Onkyo Components

Connected via ...................................................... 56

Resetting REMOTE MODE Buttons ............................. 57

Resetting the Remote Controller .................................. 57

Controlling Other Components .....................................57

Troubleshooting ............................................................. 59

Specifications ................................................................. 64

About HDMI.....................................................................65

Using an RIHD-compatible TV, Player,

or Recorder...................................................................66

Video Resolution Chart.................................................. 68

Introduction

Connections

Turning On & Basic Operations

Advanced Operations

Controlling iPod & Other Components

Others

To reset the AV receiver to its factory defaults, turn it

on and, while holding down VCR/DVR, press

ON/STANDBY (➔ 59).

6

En

Features

Amplifier

• 115 Watts/Channel @ 8 ohms (FTC)

• WRAT–Wide Range Amplifier Technology

(5 Hz to 100 kHz bandwidth)

• Optimum Gain Volume Circuitry

• H.C.P.S. (High Current Power Supply) Massive High

Power Transformer

• Jitter Cleaning Circuit Technology

Processing

• HDMI Video Upscaling (to 1080p Compatible) with

Faroudja DCDi Cinema Enhancement

• HDMI (Ver.1.4 with Audio Return Channel, 3D), Deep-

Color, x.v.Color

*

, Lip Sync, DTS

*1

-HD Master Audio,

DTS-HD High Resolution Audio, Dolby TrueHD

*2

,

Dolby Digital Plus, DSD and Multi-CH PCM

• Dolby Pro Logic IIz

*2

– New Surround Format (front-

high)

• Audyssey DSX™

*3

for New Surround Channels (front-

wide/front-high)

• Non-Scaling Configuration

•A-Form Listening Mode Memory

• Direct Mode

• Music Optimizer

*4

for Compressed Digital Music files

• 192 kHz/24-bit D/A Converters

• Powerful and Highly Accurate 32-bit Processing DSP

Connections

• 6 HDMI

*5

Inputs (1 on front panel) and 1 Output

• Onkyo for System Control

• 4 Digital Inputs (2 Optical/2 Coaxial)

• Component Video Switching (2 Inputs/1 Output)

• Front “Line in” Input for Portable audio player

• Universal Port for the Dock for iPod

*

/HD Radio™

*6

tuner module

• Banana Plug-Compatible Speaker Posts

• Powered Zone 2

• Bi-Amping Capability for FL/FR with SBL/SBR

Miscellaneous

• 40 FM/AM Presets

• Audyssey 2EQ

®*3

to Correct Room Acoustic Problems

• Audyssey Dynamic EQ™

*3

for Loudness Correction

• Audyssey Dynamic Volume™

*3

to Maintain Optimal

Listening Level and Dynamic Range

• Crossover Adjustment

(40/50/60/70/80/90/100/120/150/200 Hz)

• A/V Sync Control Function (up to 200 ms)

• On-Screen Display via HDMI

• Preprogrammed -Compatible Remote

*1

Manufactured under license under U.S. Patent #’s: 5,451,942;

5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535;

7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and

worldwide patents issued & pending. DTS is a registered

trademark and the DTS logos, Symbol, DTS-HD and DTS-

HD Master Audio are trademarks of DTS, Inc.

*2

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic” and the double-D symbol are trade-

marks of Dolby Laboratories.

*3

Manufactured under license from Audyssey Laboratories™.

U.S. and foreign patents pending. Audyssey 2EQ

®

,

Audyssey DSX™, Audyssey Dynamic Volume™ and

Audyssey Dynamic EQ™ are trademarks of

Audyssey Laboratories.

*4

Music Optimizer™ is a trademark of Onkyo Corporation.

*5

“HDMI, the HDMI Logo, and High-Definition Multimedia

Interface are trademarks or registered trademarks of HDMI

Licensing LLC in the United States and other countries.”

*6

The HD Radio Ready logo is a proprietary trademark of iBiq-

uity Digital Corp.

To receive HD Radio broadcasts, you must install an Onkyo

UP-HT1 HD Radio tuner module (sold separately).

*

Apple and iPod are trademarks of Apple Inc., registered in the

U.S. and other countries.

*

“x.v.Color” is a trademark of Sony Corporation.

7

En

Front & Rear Panels

The actual front panel has various logos printed on it. They are not shown here for clarity.

The page numbers in parentheses show where you can find the main explanation for each item.

ON/STANDBY button (➔ 19)

STANDBY indicator (➔ 19)

HDMI THRU indicator (➔ 45)

ZONE 2 indicator (➔ 49)

Remote control sensor (➔ 4)

ZONE 2, OFF, ZONE 2 LEVEL/TONE LEVEL

and TONE buttons (➔ 47, 49 to 50)

Display (➔ 8)

LISTENING MODE buttons (➔ 28)

DIMMER button (➔ 20)

MEMORY button (➔ 26)

TUNING MODE button (➔ 25)

DISPLAY button (➔ 20)

SETUP button (➔ 33)

TUNING, PRESET (➔ 25 to 26), arrow and

ENTER buttons

RETURN button

MASTER VOLUME control (➔ 20)

PHONES jack (➔ 22)

AUX INPUT HDMI jack (➔ 15)

Input selector buttons (➔ 20)

AUX INPUT LINE IN jack (➔ 16)

AUX INPUT VIDEO jack (➔ 16)

AUX INPUT AUDIO jacks (➔ 16)

SETUP MIC jack (➔ 23)

Front Panel

8

En

For detailed information, see the pages in parentheses.

Audio input indicators

Listening mode and format indicators (➔ 28, 46)

Audyssey indicators (➔ 22, 39)

Tuning indicators (➔ 25)

SLEEP indicator (➔ 21)

MUTING indicator (➔ 21)

Message area

DIGITAL IN OPTICAL and COAXIAL jacks

COMPONENT VIDEO IN and OUT jacks

HDMI IN and OUT jacks

FM ANTENNA jack and AM ANTENNA terminal

MONITOR OUT V jack

UNIVERSAL PORT jack

SPEAKERS terminals

(CENTER, FRONT, SURR, SURR BACK OR

FRONT HIGH OR FRONT WIDE)

Power cord

REMOTE CONTROL jack

Composite video and analog audio jacks

(BD/DVD IN, VCR/DVR IN and OUT, CBL/SAT IN,

GAME IN, TV/CD IN)

ZONE 2 LINE OUT jacks

SUBWOOFER PRE OUT jacks

FRONT HIGH OR FRONT WIDE OR ZONE 2

SPEAKERS terminals

Display

Rear Panel

See “Connecting the AV Receiver” for connection infor-

mation (➔ 11 to 18).

9

En

Remote Controller

For detailed information, see the pages in parentheses.

ON/STANDBY button (➔ 19)

REMOTE MODE/INPUT SELECTOR buttons

(➔ 20)

SP LAYOUT button (➔ 21)

Arrow / / / and ENTER buttons

SETUP button (➔ 33)

LISTENING MODE buttons (➔ 28)

DIMMER button (➔ 20)

DISPLAY button (➔ 20)

MUTING button (➔ 21)

VOL / button (➔ 20)

VIDEO button (➔ 21)

RETURN button

AUDIO button (➔ 21)

SLEEP button (➔ 21)

■ Controlling the tuner

To control the AV receiver’s tuner, press TUNER (or

RECEIVER).

You can select AM or FM by pressing TUNER repeatedly.

Arrow / buttons (➔ 25)

D.TUN button (➔ 25)

DISPLAY button

CH +/– button (➔ 26)

Number buttons (➔ 25)

Controlling the AV Receiver

*1

*2

*3

*1

To control component, you must first enter remote control

code.

See “Entering Remote Control Codes” for more details

(➔ 56).

*2

This button acts as a shortcut for the Video menu (➔ 21).

*3

This button acts as a shortcut for the Audio menu (➔ 21).

To control the AV receiver, press RECEIVER to select

Receiver mode.

You can also use the remote controller to control

Onkyo Blu-ray Disc/DVD player, CD player, and

other components.

See “Entering Remote Control Codes” for more

details (➔ 56).

10

En

About Home Theater

Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your

own home—just like being in a movie theater or concert hall. With Blu-ray Discs, you can enjoy DTS and Dolby Digital.

With analog or digital TV, you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo’s original DSP listening modes.

Enjoying Home Theater

Front speakers

These output the overall sound. Their role in a home theater is to provide

a solid anchor for the sound image. They should be positioned facing the

listener at about ear level, and equidistant from the TV. Angle them inward

so as to create a triangle, with the listener at the apex.

Center speaker

This speaker enhances the front speakers, making sound movements dis-

tinct and providing a full sound image. In movies it’s used mainly for dia-

log. Position it close to your TV facing forward at about ear level, or at the

same height as the front speakers.

Surround speakers

These speakers are used for precise sound positioning and to add realistic

ambience. Position them at the sides of the listener, or slightly behind,

about 2 to 3 feet (60 to 100 cm) above ear level. Ideally they should be

equidistant from the listener.

Surround back speakers

These speakers are necessary to enjoy Dolby Digital EX, DTS-ES Matrix,

DTS-ES Discrete, etc. They enhance the realism of surround sound and

improve sound localization behind the listener. Position them behind the

listener about 2 to 3 feet (60 to 100 cm) above ear level.

Front high speakers

These speakers are necessary to enjoy Dolby Pro Logic IIz Height, and

Audyssey DSX™. They significantly enhance the spatial experience.

Position them at least 3.3 feet (100 cm) above the front speakers (prefera-

bly as high as possible) and at an angle slightly wider than the front speak-

ers.

Front wide speakers

These speakers are necessary to enjoy Audyssey DSX. They significantly

enhance the spatial experience. Position them well outside of the front

speakers. See also

http://www.audyssey.com/technology/dsx.html

about

optimum speaker placement for Audyssey DSX.

Subwoofer

The subwoofer handles the bass sounds of the LFE (Low-Frequency

Effects) channel. The volume and quality of the bass output from your

subwoofer will depend on its position, the shape of your listening room,

and your listening position. In general, a good bass sound can be obtained

by installing the subwoofer in a front corner, or at one-third the width of

the wall, as shown.

Corner

position

1/3 of wall

position

Tip

• To find the best position for your subwoofer, while

playing a movie or some music with good bass,

experiment by placing your subwoofer at various

positions within the room, and choose the one that

provides the most satisfying results.

11

En

Connecting the AV Receiver

Speaker Configuration

The following table indicates the channels you should use

depending on the number of speakers that you have.

For 7.1-channel surround-sound playback, you need seven

speakers and a powered subwoofer.

*1

If you’re using only one surround back speaker, connect it to

the SURR BACK OR FRONT HIGH OR FRONT WIDE L

terminals.

*2

Front high, surround back and front wide speakers cannot be

used at the same time.

No matter how many speakers you use, a powered sub-

woofer is recommended for a really powerful and solid

bass.

To get the best from your surround sound system, you

need to set the speaker settings. You can do this automati-

cally (➔ 23) or manually (➔ 35).

Attaching the Speaker Cable Labels

The AV receiver’s positive (+) speaker terminals are all

red (the negative (–) speaker terminals are all black).

The supplied speaker cable labels are also color-coded and

you should attach them to the positive (+) side of each

speaker cable in accordance with the table above. Then all

you need to do is to match the color of each label to the

corresponding speaker terminal.

Speaker Connection Precautions

Read the following before connecting your speakers:

• You can connect speakers with an impedance of between

6 and 16 ohms. If you use speakers with a lower imped-

ance, and use the amplifier at high volume levels for a

long period of time, the built-in amp protection circuit

may be activated.

• Disconnect the power cord from the wall outlet before

making any connections.

• Read the instructions supplied with your speakers.

• Pay close attention to speaker wiring polarity. In other

words, connect positive (+) terminals only to positive (+)

terminals, and negative (–) terminals only to negative (–)

terminals. If you get them the wrong way around, the

sound will be out of phase and will sound unnatural.

• Unnecessarily long, or very thin speaker cables may

affect the sound quality and should be avoided.

• Be careful not to short the positive and negative wires.

Doing so may damage the AV receiver.

• Make sure the metal core of the wire does not have con-

tact with the AV receiver’s rear panel. Doing so may

damage the AV receiver.

Connecting Your Speakers

Number of channels2345677788999

Front speakers ✔✔✔✔✔✔✔✔✔✔✔✔✔

Center speaker ✔ ✔✔✔✔✔✔✔✔✔✔

Surround speakers ✔✔✔✔✔✔✔✔✔✔✔

Surround back

speaker

*1*2

✔✔✔

Surround back

speakers

*2

✔✔✔

Front high speakers

*2

✔✔✔✔

Front wide speakers

*2

✔✔✔✔

Speaker Color

Front left, Front high left, Front wide left White

Front right, Front high right, Front wide right Red

Center Green

Surround left Blue

Surround right Gray

Surround back left, Zone 2 left Brown

Surround back right, Zone 2 right Tan

12

En

• Don’t connect more than one cable to each speaker ter-

minal. Doing so may damage the AV receiver.

• Don’t connect one speaker to several terminals.

Connecting the Speaker Cables

Screw-type speaker terminals

Using Banana Plugs

• If you are using banana plugs, tighten the speaker terminal before inserting the banana plug.

• Do not insert the speaker code directly into the center hole of the speaker terminal.

Push-type speaker terminals

The following illustration shows which speaker should be connected to each pair of terminals. If you’re using only one

surround back speaker, connect it to the SURR BACK OR FRONT HIGH OR FRONT WIDE L terminals.

Strip 1/2" to 5/8" (12 to 15 mm) of

insulation from the ends of the

speaker cables, and twist the bare

wires tightly, as shown.

1/2" to 5/8"(12 to 15 mm)

Strip 3/8" to 1/2" (10 to 12 mm) of insulation from the ends of

the speaker cables, and twist the bare wires tightly, as shown.

3/8" to 1/2"(10 to 12 mm)

Surround back

left speaker

Surround

left speaker

Surround

right speaker

Front high

right speaker/

Front wide

right speaker

Front high

left speaker/

Front wide

left speaker

Center

speaker

Front left

speaker

Surround back

right speaker

Front right

speaker

13

En

Note

• The front wide speakers can also be connected to the FRONT HIGH OR FRONT WIDE OR ZONE 2 SPEAKERS terminals. When

doing so, set “Front High/Front Wide/Zone2” in Speaker Setup to “Front Wide” (➔ 36).

• The front high or front wide speakers can also be connected to the SURR BACK OR FRONT HIGH OR FRONT WIDE SPEAK-

ERS terminals. When doing so, set “Surr Back/Front High/Front Wide” in Speaker Setup to “Front High” or “Front Wide” (➔ 36).

Connecting a Powered Subwoofer

Using a suitable cable, connect the AV receiver’s

SUBWOOFER PRE OUT jack to an input on

your powered subwoofer, as shown. If your sub-

woofer is unpowered and you’re using an external

amplifier, connect the SUBWOOFER PRE OUT

jack to an input on the amp.

You can connect the powered subwoofer with two

SUBWOOFER PRE OUT jacks respectively.

The same signal is output from each jack.

Bi-amping the Front Speakers

The FRONT L/R and SURR BACK OR FRONT

HIGH OR FRONT WIDE L/R terminal posts can be

used with front speakers and surround back speakers

respectively, or bi-amped to provide separate tweeter

and woofer feeds for a pair of front speakers that sup-

port bi-amping, providing improved bass and treble per-

formance.

• When bi-amping is used, the AV receiver is able to

drive up to a 5.1 speaker system in the main room.

• For bi-amping, the FRONT L/R terminal posts con-

nect to the front speakers’ woofer terminals; the

SURR BACK OR FRONT HIGH OR FRONT

WIDE L/R terminal posts connect to the front speak-

ers’ tweeter terminals.

• Once you’ve completed the bi-amping connections

shown below and turned on the AV receiver, you must

set the “Speakers Type” setting to “Bi-Amp” to

enable bi-amping (➔ 35).

Important:

• When making the bi-amping connections, be sure to remove the jumper bars that link the speakers’ tweeter (high) and woofer (low)

terminals.

• Bi-amping can be used only with speakers that support bi-amping. Refer to your speaker manual.

L E N T

LINE INPUT

NE P T

LINE INPUT

Powered subwoofer

Woofer (low)

Left

speaker

Tweeter (high)

Right

speaker

14

En

Connected image with AV components

• Before making any AV connections, read the manuals supplied with your AV components.

• Don’t connect the power cord until you’ve completed and double-checked all AV connections.

• Push plugs in all the way to make good connections (loose connections can cause noise or malfunc-

tions).

• To prevent interference, keep audio and video cables away from power cords and speaker cables.

AV Cables and Jacks

*

Available sampling rate for PCM input signal is 32/44.1/48/88.2/96 kHz. Even 176.4/192 kHz is effective in case of the HDMI con-

nection.

Note

• The AV receiver does not support SCART plugs.

• The AV receiver’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s removed.

Push plugs in all the way.

Caution

• To prevent shutter damage, hold the optical plug straight when inserting and removing.

About AV Connections

Signal Cable Jack Description

Video and

Audio

HDMI HDMI connections can carry digital video and audio.

Video Component video Component video separates the luminance (Y) and color

difference signals (P

B/CB, PR/CR), providing the best pic-

ture quality (some TV manufacturers label their compo-

nent video sockets slightly differently).

Composite video Composite video is commonly used on TVs, VCRs, and

other video equipment.

Audio Optical digital

audio

Optical digital connections allow you to enjoy digital

sound such as PCM

*

, Dolby Digital or DTS. The audio

quality is the same as coaxial.

Coaxial digital

audio

Coaxial digital connections allow you to enjoy digital

sound such as PCM

*

, Dolby Digital or DTS. The audio

quality is the same as optical.

Analog audio

(RCA)

Analog audio connections (RCA) carry analog audio.

1/8" (3.5 mm)

Stereo mini plug

This cable carries analog audio.

HDMI cable Other cables

: Video & Audio

: Video

: Audio

Game console

Blu-ray Disc/

DVD player

TV, projector, etc.

Game console

Blu-ray Disc/

DVD player

TV, projector, etc.

AV receiverAV receiver

Right!

Wrong!

HDMI

Y

P

B/CB

PR/CR

Green

Blue

Red

V

Yellow

OPTICAL

Orange

L

R

White

Red

15

En

Connect your components to the appropriate jacks. The default input assignments are shown below.

✔: Assignment can be changed (➔ 34).

Refer to “About HDMI” (➔ 65) and “Using an RIHD-compatible TV, Player, or Recorder” (➔ 66).

Tip

To listen to audio received by the HDMI IN jacks through your TV’s speakers:

• Set the “TV Control” setting to “On” (➔ 45) for an -compatible TV.

•Set the “Audio TV Out” setting to “On” (➔ 44) when the TV is not compatible with or the “TV Control” setting to “Off”.

• Set your Blu-ray Disc/DVD player’s HDMI audio output setting to PCM.

• To listen to TV audio through the AV receiver, see “Connecting External Components” (➔ 16).

Note

• When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be seen on the TV

screen (on the TV, select the input of the HDMI component connected to the AV receiver). If the TV power is off or the TV is set to

another input source, this may result in no sound from the AV receiver or the sound may be cut off.

•When the “Audio TV Out” setting is set to “On” (➔ 44) to hear from your TV’s speakers, by controlling the AV receiver’s volume,

the sound will be output from the AV receiver’s speakers, too. When the

“TV Control” setting is set to “On” (➔ 45) to hear from

speakers of -compatible TV, by controlling the AV receiver’s volume, the AV receiver’s speakers will produce sound while the

TV’s speakers are muted. To stop the AV receiver’s speakers producing sound, change the settings, change your TV’s settings, or turn

down the AV receiver’s volume.

■ Audio return channel (ARC) function

Audio return channel (ARC) function enables an HDMI capable TV to send the audio stream to the HDMI OUT of the

AV receiver. To use this function, you must select the TV/CD input selector.

• To use ARC function, you must select the TV/CD input selector, your TV must support ARC function and “HDMI

Control” is set to “On”(

➔ 45).

Connecting Components with HDMI

Jack Signal Components Assignable

Input HDMI IN 1 Audio/Video Blu-ray Disc/DVD player ✔

HDMI IN 2 VCR or DVD recorder/Digital Video Recorder ✔

HDMI IN 3 Satellite, cable, set-top box, etc. ✔

HDMI IN 4 Game console ✔

HDMI IN 5 Other components ✔

AUX INPUT HDMI Camcorder

Output HDMI OUT TV, projector, etc.

Game console

VCR or DVD recorder/Digital Video Recorder

TV, projector, etc.

Satellite, cable, set-top box, etc.

Blu-ray Disc/DVD player

Camcorder

Other components

16

En

Connect your components to the appropriate jacks. The default input assignments are shown below.

✔: Assignment can be changed (➔ 35).

Note

• When you connect to both AUX INPUT AUDIO jacks and AUX INPUT LINE IN jack at the same time, AUX INPUT LINE IN jack

will be given a higher priority.

• The AV receiver can output audio and video signals from the AUX INPUT jacks to the VCR/DVR OUT jacks.

*1

Connect a turntable (MM) that has a phono preamp built-in. If your turntable (MM) doesn’t have it, you’ll need a commercially

available phono preamp.

If your turntable has a moving coil (MC) type cartridge, you’ll need a commercially available MC head amp or MC transformer as

well as a phono preamp. See your turntable’s manual for details.

• With connection , you can listen and record audio from the external components while you are in Zone 2. You can lis-

ten and record audio from the external components in the main room; you can listen to the audio in Zone 2 as well.

• With connection , you can enjoy Dolby Digital and DTS. (To record or listen in Zone 2 as well, use and .)

• With connection

, if your Blu-ray Disc/DVD player has both the main stereo and multichannel outputs, be sure to

connect the main stereo.

■ How to record the video

• With the connections described above, you cannot record the video through the AV receiver. To make a connection for

video recording (➔ 27).

Connecting External Components

The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to

the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver’s display when changing settings.

No. Jack Signal Components Assignable

AUX INPUT LINE IN Analog audio Portable audio player

VIDEO Composite video Camcorder, etc

AUDIO L/R Analog audio

COMPONENT

VIDEO

IN 1 (BD/DVD) Component video Blu-ray Disc/DVD player ✔

IN 2 (CBL/SAT) Satellite, cable, set-top box, etc. ✔

OUT TV, projector, etc.

DIGITAL IN OPTICAL IN 1 (GAME) Digital audio Game console ✔

IN 2 (TV/CD) TV, CD player ✔

COAXIAL IN 1 (BD/DVD) Blu-ray Disc/DVD player ✔

IN 2 (CBL/SAT) Satellite, cable, set-top box, etc. ✔

MONITOR OUT Composite video TV, projector, etc.

BD/DVD IN Analog audio and

composite video

Blu-ray Disc/DVD player

VCR/DVR IN VCR or DVD recorder/Digital

Video Recorder

CBL/SAT IN Satellite, cable, set-top box, etc.

GAME IN Game console

TV/CD IN Analog audio

TV, CD player, Turntable

*1

,

Cassette tape deck, MD, CD-R

UNIVERSAL PORT Analog audio/

Video

Universal port optional dock

(UP-A1 etc.)

Front Rear

17

En

With (Remote Interactive), you can use the following

special functions:

■ System On/Auto Power On

When you start playback on a component connected via

while the AV receiver is on Standby, the AV

receiver will automatically turn on and select that com-

ponent as the input source.

■ Direct Change

When playback is started on a component connected via

, the AV receiver automatically selects that compo-

nent as the input source.

■ Remote Control

You can use the AV receiver’s remote controller to con-

trol your other -capable Onkyo components, point-

ing the remote controller at the AV receiver’s remote

control sensor instead of the component. You must enter

the appropriate remote control code first (➔ 56).

Note

•Use only cables for connections. cables are supplied

with Onkyo players (DVD, CD, etc.).

• Some components have two jacks. You can connect either

one to the AV receiver. The other jack is for connecting addi-

tional -capable components.

• Connect only Onkyo components to jacks. Connecting other

manufacturer’s components may cause a malfunction.

• Some components may not support all functions. Refer to

the manuals supplied with your other Onkyo components.

• While Zone 2 is on, the System On/Auto Power On and Direct

Change functions do not work.

This section explains how to connect the supplied indoor FM antenna and AM loop antenna.

The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use

the tuner.

Note

• Once your AV receiver is ready for use, you’ll need to tune into a radio station and position the antenna to achieve the best possible

reception.

• Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

Tip

• If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.

• If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM

antenna.

Connecting Onkyo Components

Step 1:

Make sure that each Onkyo component is connected

with an analog audio cable (connection in the

hookup examples) (➔ 16).

Step 2:

Make the connection (see illustration below).

Step 3:

If you’re using an RI Dock, or cassette tape deck,

change the Input Display (➔ 22).

LR

IN

BD/DVD

L

R

IN

TV/CD

L

R

REMOTE

CONTROL

ANALOG

AUDIO OUT

LR

ANALOG

AUDIO OUT

e.g., CD player

e.g., DVD player

Connecting Antenna

Thumbtacks, etc.

Insert the plug fully

into the jack.

Push. Insert wire. Release.

Assembling the AM loop antenna

Indoor FM antenna (supplied)

AM loop antenna (supplied)

Caution

• Be careful that you don’t injure yourself when

using thumbtacks.

18

En

The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format

you choose will depend on the formats supported by your components. Use the following sections as a guide.

Video Connection Formats

Video component can be connected by using any one of the

following video connection formats: composite video, com-

ponent video, or HDMI, the latter offering the best picture

quality.

Video input signals flow through the AV receiver as shown,

with composite video and component video sources all being

upconverted for the HDMI output.

The composite video and component video outputs pass

through their respective input signals as they are.

When you connect audio component to an HDMI or COM-

PONENT input, you must assign that input to an input selec-

tor (➔ 34).

■ Signal Selection

If signals are present at more than one input, the inputs will

be selected automatically in the following order of priority:

HDMI, component video, composite video.

However, for component video only, regardless of whether a

component video signal is actually present, if a component

video input is assigned to the input selector, that component

video input will be selected. And if no component video

input is assigned to the input selector, this will be interpreted

as no component video signal being present.

In the Signal Selection Example shown on the right, video

signals are present at both the HDMI and composite video

inputs, however, the HDMI signal is automatically selected

as the source and video is output by the HDMI outputs.

Audio Connection Formats

Audio component can be connected by using any of the

following audio connection formats: analog, optical, coax-

ial, or HDMI.

When choosing a connection format, bear in mind that the

AV receiver does not convert digital input signals for ana-

log line outputs and vice versa. For example, audio signals

connected to an optical or coaxial digital input are not out-

put by the analog VCR/DVR OUT.

If signals are present at more than one input, the inputs

will be selected automatically in the following order of pri-

ority: HDMI, digital, analog.

Which Connections Should I Use?

The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to

the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver’s display when changing settings.

IN

MONITOR OUT

Blu-ray Disc/DVD player, etc.

AV receiver

TV, projector, etc.

Composite

Component

Video Signal Flow Chart

HDMI

IN

MONITOR OUT

Blu-ray Disc/DVD player, etc.

AV receiver

TV, projector, etc.

Composite

Component

Signal Selection Example

HDMI

IN

OUT

*

1

*

2

*

1

*

1

*

1

Blu-ray Disc/DVD player, etc.

AV receiver

TV, projector, etc.

HDMICoaxial Analog

Audio Signal Flow Chart

HDMI Analog

Optical

*1

Depends on the “Audio TV Out” setting (➔ 44).

*2

This setting is available, when “Audio Return Channel”

setting is set to “Auto” (➔ 45), you must select the TV/CD

input selector and your TV must support ARC function.

19

En

Turning On/Off the AV Receiver

Turning On

Press ON/STANDBY on the front panel.

or

Press RECEIVER followed by ON/STANDBY on the remote controller.

The AV receiver comes on, the display lights, and the STANDBY indicator goes off.

Turning Off

Press ON/STANDBY on the front panel or the remote controller.

The AV receiver will enter Standby mode. To prevent any loud surprises when you turn on the AV receiver, always

turn down the volume before you turn it off.

ON/STANDBY

RECEIVER

Remote controller

ON/STANDBY

STANDBY indicator

Front panel

20

En

Basic Operations

You can determine the language used for the onscreen

setup menus. See “OSD Setup” (➔ 43).

■ Operating on the AV receiver

■ Operating with the remote controller

You can display various information about the current

input source as follows. (Components connected to the

UNIVERSAL PORT jack are excluded.)

Tip

• Alternatively, you can use the AV receiver’s DISPLAY.

The following information can typically be displayed.

*1

When AM or FM radio is used, the band, preset number, and

frequency are displayed.

*2

If the input signal is analog, no format information is dis-

played. If the input signal is PCM, the sampling frequency is

displayed. If the input signal is digital but not PCM, the signal

format is displayed.

Information is displayed for about three seconds, then the pre-

viously displayed information reappears.

*3

The input source is displayed with the default name even

when you have entered a custom name in “Name Edit”

(➔ 40).

You can adjust the brightness of the AV receiver’s display.

Tip

• Alternatively, you can use the AV receiver’s DIMMER.

The on-screen menus appear only on a TV that is con-

nected to the HDMI OUT. If your TV is connected to

the MONITOR OUT V or the COMPONENT VIDEO

OUT, use the AV receiver’s display when changing

settings.

This manual describes the procedure using the

remote controller unless otherwise specified.

Selecting the Language Used for the

Onscreen Setup Menus

Playing the Connected Component

1

Use the input selector buttons to select the input

source.

2

Start playback on the source component.

See also:

• “Controlling Other Components” (➔ 55)

• “Controlling iPod” (➔ 51)

• “Listening to the Radio” (➔ 25)

3

To adjust the volume, use MASTER VOLUME

control.

4

Select a listening mode and enjoy!

See also:

• “Using the Listening Modes” (➔ 28)

• “Audyssey” (➔ 39)

1

Press RECEIVER followed by INPUT SELEC-

TOR.

2

Start playback on the source component.

See also:

• “Controlling Other Components” (➔ 55)

• “Controlling iPod” (➔ 51)

• “Listening to the Radio” (➔ 25)

3

To adjust the volume, use VOL / .

4

Select a listening mode and enjoy!

See also:

• “Using the Listening Modes” (➔ 28)

• “Audyssey” (➔ 39)

Displaying Source Information

Press RECEIVER followed by DISPLAY repeat-

edly to cycle through the available information.

Setting the Display Brightness

Press RECEIVER followed by DIMMER repeat-

edly to select: dim, dimmer, or normal brightness.

Input source &

volume

*1

Signal format

*2

or sampling fre-

quency

Input source &

listening mode

*3

Input & output

resolution

Page is loading ...

ONKYO HT-RC260 User manual

This manual is also suitable for

ONKYO HT-RC260 User manual

Related papers

Other documents