Kenmore 116.34720400 Owner's manual

Category
Vacuum cleaners
Type
Owner's manual

This manual is also suitable for

Owner'sManual
ManualDelPropietario
VacuumCleaner
Aspiradora
Model, Modelo
116,33720
116.33721
116.3472O
116.34721
CAUTION:
Read and follow all
safety and operating
instructions before first
use of this product.
CUIDADO:
Lea y sigue todas las
instrucciones de operaci6n
y seguridad antes del uso de
este producto.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www.sears.com
Part No. CQ1ZCAF3QUQG-KCO1ZCAF3QUQ
Printed in Mexico
Impreso en M_xico
Before UsingYour New Vacuum ........ 2
KenmoraVacuum Cleaner Warranty .... 2
ImportantSafety Instructions ........... 3
Parts and Features ................... 4
AssemblyInstructions ............... 5-6
Operating Instructions ................. 7
Pile HeightSelection and Setting ........ 7
Releasingthe Handle ................. 8
ON/OFF Switch ..................... 8
Attachments ..................... 9-10
AttachmentUse Chart ............... 10
VacuumingTips .................... 11
PerformanceFeatures ............... 11
Vacuum Cleaner Care ............... 12
Vacuum Storage ................... 12
Cleaning Exteriorand Attachments ..... 12
Dust BinCleaning ................ 13-14
Secondary FilterCleaning ............ 14
FilterChanging/Cleaning ............. 15
BeltChangingand AgitatorCleaning.. 16-17
Clog Removat ..................... 18
Motor Protector ..................... 18
AgitatorServicing................... 19
AgitatorAssembly .................. 19
LightBulb Changing ................. 20
Troubleshooting ..................... 21
Notes ............................... 22
Please read this guide. It will help you assemble and operate your new Kenmore vacuum in
the safest and most effective way.
For more information about vacuum cleaner care and operation, call your nearest Sears store.
You will need the complete model and serial numbers when requesting information. Your vacu-
um's model and serial numbers are located on the Model and Serial Number Plate.
Use the space below to record the model number and serial number of your new Kenmore
vacuum.
Model No.
Serial No.
Date of Purchase
Keep this book and your sales check (receipt) in a safe place for future reference.
LIMITED ONE YEAR WARRANTY ON KENMORE VACUUM CLEANER
This warranty is for one year from the date of purchase, and includes only private household
vacuum cleaner use. During the warranty year, when this vacuum cleaner is operated and
maintained according to the owner's manual instructions, Sears will repair any defects in
materiar or workmanship free of charge.
This warranty excludes vacuum bags, belts, light bulbs, and filters, which are expendable parts
and become worn during normal use.
For warrantyservice,retum this vacuum cleaner tothe nearest Sears Service Center in the
UnitedStates.
This warranty applies only while this product is in use in the United States. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.
Seam, Roebuckand Co., D/817 WA, Hoffman Estates, IL 60179
2
Your safety is importantto us. To reduce the riskof fire, electricalshock, injuryto per-
sons ordamage when usingyour vacuum cleaner, follow basic safety precautions
including the following:
Reed this manual before assembling or
using your vacuum cleaner.
Use your cleaner only as described in
this manual. Use only with Sears recom-
mended attachments.
To reduce the risk of electrical shock -
Do not use outdoors or on wet surfaces.
Disconnect electrical supply before any
servicing or cleaning. Failure to do so
could result in electrical shock or per-
sonal injury.
Always turn cleaner off before unplug-
ging.
Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
Do not use with damaged cord or plug. If
cleaner is not working as it should, has
been dropped, damaged, left outdoors,
or dropped into water, return it to a
Sears Service Center.
Do not pull or carry by cord, use cord as
a handle, close door on cord, or pull
cord around sharp edges or corners.
Do not run cleaner over cord. Keep cord
away from heated surfaces.
Do not leave cleaner when plugged in.
Unplug from outlet when not in use and
before servicing.
Do not allow to be used as a toy. Close
attention is necessary when used by or
near children.
Do not handle plug or cleaner with wet
hands.
Do not put any objects into openings.
Do not use with any opening blocked;
keep free of dust, lint, hair and anything
that may reduce air flow.
Keep hair, loose clothing, fingers, and all
parts of body away from openings and
moving parts.
Do not use cleaner without dust bin
and/or filters in place.
Always clean the dust bin after vacuum-
ing carpet cleaners or freshener, pow-
ders and fine dust. These products clog
the filters, reduce airflow and can cause
damage to the cleaner. Failure to clean
the dust bin could cause permanent
damage to the cleaner.
Do not use the cleaner to pick up sharp
hard objects, small toys, pins, paper
clips, etc. They may damage the clean-
er or dust bin.
Do not pick up anything that is burning
or smoking, such as cigarettes, match-
es, or hot ashes.
Do not use cleaner to pick up flammable
or combustible liquids (gasoline, clean-
ing fluids, perfumes, etc.), or use in
areas where they may be present. The
fumes from these substances can create
a fire hazard or explosion.
Use extra care when cleaning on stairs.
Do not put on chairs, tables, etc. Keep
on floor.
You are responsible for making sure that
your vacuum cleaner is not used by any-
one unable to operate it properly.
SAVE THESE INSTRUCTIONS
Proper assembly and safe use of your vacuum cleaner are your responsibilities. Your
cleaner is intended only for household use. Read this Owner's Manual carefully for
important use and safety information. This guide contains safety statements under
warning and caution symbols. Please pay special attention to these boxes and follow
any instructions given. WARNING statements alert you to such dangers as fire, elec-
trical shock, burns and personal injury. CAUTION statements alert you to such dan-
gers as personal injury and/or property damage.
3
It is important to know your vacuum cleaner's parts and features to assure its proper and safe
use. Review these before using your cleaner.
Item Part No. Part No.
In U.S. In Canada
Belt 20-5275 20-40096
Headlight Bulb 20-5240 20-40600
Primary Filter 20-82720
Exhaust Filter 20-86889 20o86889C
Hose
Dust Bin
Release
Handle --
Power
Cord.
Screw
Filter
Hose (Inside)
Holder
Cord Hook
Nozzle
Cover
Brush
Wand
Furniture
Guard
Retainer/
Carry Handle
-Dust
Bin
Exhaust
(Inside)
(Some Models)
Nozzle
Base
Nozzle Cover
Retainers
On/Off
Switch
Handle
Release
Model/Serial
Numbers
Tool
Motor
Protector
Sho_
Hose
EXTENSION HOSE KITS
SOME MODELS
Extension Hose
SOME NI()[)_ELS-
_FI _Adaptor
oor Brush
Wand
4
Before assembling vacuum, check the
PACKING LIST on the cover of the separate
Repair Parts List. Use this list to verify that
you have received all the components of
your new Kenmore vacuum.
ElectricalShock Hazard
Do not plugintothe electricalsupply
untilthe assembly iscomplete. Failure
to do so could result in electdcal shock
orinjury.
HANDLE ASSEMBLY
Remove the screw located just below the
top edge of the back of the vacuum.
Position the handle as shown in the illustra-
tion below.
While holding the power cord out of the way,
slide the handle into the opening at the top
of the vacuum.
Handle
Handle
Screw
Hole
Insert the screw so it passes through the
handle into the vacuum.
Begin to tighten the screw with your fingers.
It may be necessary to adjust the handle
slightly.
5
CAUTION
Do notovertighten.
Overtighteningcould stdp the screw
holes.
Do notoperate the cleaner withoutthe
screw in place.
Using a screw-
driver, tighten
the screw.
CORD ASSEMBLY
Make sure the quick release cord hook is in
the upright position. Remove the wire tie
from the power cord.
Lock the cord into
place by forcing it
into the locking
notch on the body Lockin
of the quick Notch
release cord hook
as shown. This
helps keep the
power cord out
from under the Power
vacuum cleaner
agitator.
Quick
Release
Curd
Power
Lower
Cord
Wrap the
power cord
around the
quick release
cord hook
and lower
cord retainer,
then lock the
power cord
plug onto the
power cord.
ATTACHMENT STORAGE
After the handle has been assembled to the
body and the power cord has been wrapped
around the cord hooks, the attachments can
be placed in their holders.
1. Snap the suction inlet end of the hose
into the back of the vacuum cleaner.
2. Place the hose behind the handle and
over the hose holder.
3. Place the hose in the front slot of the
tool holder, twisting and pushing down over
the short hose to assure a good connection.
4. Place the extension wand in the rear slot
of the tool holder.
5. Slide the crevice tool into the slot beside
the wand.
6. Place the dusting brush or combination
brush on the wand with the brush portion
up.
Handle-
Hose
Dusting
Brush
Extension
Wand
Q
Inlet
Tool
Holder
Tool
HOWTO START
Quick
Release
Hook
1.Turn the quick
release cord
hook to either
side and down
to release the
power cord.
2. Release the power cord plug from the
power cord and pull the cord off the quick
release cord hook. Check to be sure the
power cord is still locked into the locking
notch in the quick release cord hook.
NOTE: To reduce the risk of electric shock,
this vacuum cleaner has a polarized plug;
one blade is wider than the other. This plug
will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, con-
tact a qualified technician to install the prop-
er outlet. Do not change the plug in any
way.
Personal Injury and Product
Damage Hazard
• DO NOT plugin if switchis inthe
ON position.Personal injuryor
damage couldresult.
• DO NOT use outletsabove coun-
ters. Damage from cordto items in
surroundingarea couldoccur.
3. Plug the polarized power cord into a
120 Volt outlet located near the floor.
Models with no selector adjust automatically
for varying carpet heights.
SOME MODELS
To select a pile height setting:
Turn off cleaner. Select a pile height setting
by tilting the cleaner back until front wheels
are lifted slightly off the floor as illustrated.
Slide the adjustment lever to the correct
setting.
SUGGESTED PILE HEIGHT SETTINGS
You may need to raise the height to make
some jobs easier, such as scatter rugs and
longer pile carpets. Suggested settings are:
Models withtwo (2) positions:
HIGH: medium to long pile.
LOW: short to mediumpile.
Models with four (4) positions:
HIGH: shag carpet, long pile, plush, scatter
rugs
MED: medium to long pile.
LOW: short to medium pile.
EX LOW: very low pile.
Place unit in "HIGH" when usingattach-
ments to prevent possiblefloordamage.
AI-I'ENTION: Special care is required when
vacuuming certain types of carpet or floor
covering. Always check the carpet or floor
covering manufacturer's recommended
cleaning instructions before vacuuming.
Releasethehandlebyplacingyourfooton
thefootrestandpullbackonthehandle
untilit releasesfromitsuprightposition.
Foot Rest For
Handlq
SOME MODELS
Release the handle by pressing down on
the handle release pedal with your foot and
pulling back and down on the handle with
your hand.
r-7
Handle
Release Pedal
To start the vacuum cleaner, step on the
ON/OFF switch located on the back of the
vacuum. To stop the vacuum cleaner, step
on the switch a second time.
On/Off
8
PersonalInjuryHazard and Property
Hazard
DO NOT place hands or feet under-
neath the unitat any time. When using
attachments,the agitatorcontinues
rotating. Do notallow the cleaner to
remain in just one place for a periodof
time as the agitatormay damage the
floor surface. Avoid placingthe cleaner
on furniture, the fdnged area of rugs,
deep pile carpeting,or carpeted stairs.
The ideal positionforthe cleaner when
usingattachments is for the unitto be
on a level area with the handle in the
f_ position.
TO USE ATrACHMENTS
I CAUTION
DO NOT tip vacuum cleaner forwards or
sideways when using attachments.
The attachments will fit on the hose or the
wand. In addition, the dusting brush or
combination brush will also fit on the crevice
tool.
The hose and wand can be pulled off the
short hose by grasping the cuff and twisting
while pulling up.
! CAUTION
DO NOT pull the vacuum cleaner
around the room by the hose.
Property damage could result.
The attachments can be added to the hose
if the item to be cleaned is not far from the
creaner. The hose on some moders will
expand.
NOTE: When cleaner is turned on, the hose
on some models will have a tendency to
collapse due to suction of the cleaner.
if more reach is needed, the wand can be
attached to the hose and the attachments
can be added to the wand.
When using attachments, be careful
not to overextend the hose length
when reaching. Trying to reach
beyond the hose reach could cause
the cleaner to tip over.
SOME MODELS
An extra wand, without tabs, is included.
This extra wand can be added to the
wand with tabs for extra reach. Insert
wand and twist a quarter of a turn to
secure fit.
Crov, o,-- o,-
_Dusting Brush Wand
(Some Models) _
Combination
Brush (Some
Models)
If the dusting brush/combination brush is
being used and more distance is
needed, the crevice tool can be added to
the wand, then the dusting
brush/combination brush can be added
to the crevice tool.
TO STORE
A'I-FACHMENTS
Return the hose to its position on the
short hose and the attachments to their
holders.
Attachmentsused in dirtyareas, such
as under a refrigerator,shouldnot be
used on othersurfaces untilthey are
washed. They could leave marks.
9
When using the regular hose or with
the extension hose attached, the
cleaner should be on a solid surface
on the same level or below the level of
the user's feet. DO NOT use the hoses
when the cleaner Is above the level of
I the user's feet.
I
EXTENSION HOSE
SOME MODELS
Some models include an extra hose which
connects to the stretch hose on the vacuum
for a longer cleaning reach.
Unit Hose _ Extension Hose
Insert the two tabs on the end of the
extension hose into the two "J" shaped slots
on the unit hose and twist to connect.
All attachments and the wand can be
attached to the open end of the hose.
FLOOR BRUSH AND WAND
SOME MODELS
Some models have an extra brush and wand
for cleaning bare floors. Twist one end of the
adaptor into the floor brush and the other
end into the straight wand. Connect the
straight wand to the telescopic wand and
then to the vacuum hose or extension hose.
(}J
A'I-FACHMENT
DUSTING BRUSH <_
CREVICE TOOL ¢_ _
COMBINATION BRUSH
Handi-Mate ® Jr.
Fumiture*
X
X
X
X
CLEANING AREA
Between
Cushions*
X
Drapes* Stairs
X X
X
X X
X
Walls
X
The motor protector may open when using attachments or when cleaning new carpet due to
reduced air flow caused by the attachments themselves or by new carpet fuzz filling the bag
quickly.
*Always clean attachments before using on fabrics.
10
Personal InjuryHazard
Use care Ifvacuum cleaner Is placed
on stairs.If itfalls, personal injuryor
propertydamage couldresult.
Carpet edges
Guide either side or the front of the nozzle
along a baseboard. The full length brushes
help remove trapped dirt at carpet edges.
Stairs
Put handle in ful! upright position. Use the
crevice tool or dusting brush. Set the On/Off
switch to ON.
MOTOR PROTECTION
SYSTEM
Thermal Protector
This vacuum has a thermal protector which
automatically trips to protect the vacuum
from overheating. If a clog prevents the
normal flow of air to the motor, the thermal
protector turns the motor off automatically to
allow the motor to cool in order to prevent
possible damage to the vacuum.
To correct problem: Ifthis occurs, turn the
vacuum off and unplug the power cord from
the outlet to allow the vacuum to cool and
the thermal protector to reset. Check for
and removeclogs, ifnecessary. Alsocheck
and clean/replace any cloggedfilters. Wait
approximatelythirty (30) minutesand plug
the vacuum in and turn back on to see ifthe
motorprotectorhas reset.The motor
protectorwill not reset if the vacuum is not
tumed offeven if the vacuum hascooled
down.
PERFORMANCE
INDICATOR
SOME MODELS
When the unit is running with normal air
flow, the light on the performance indicator
is off. The light comes on whenever the
airflow becomes blocked. If that occurs,
check the dust bin, clean/replace clogged
filters, and check other possible clog
locations shown in CLOG REMOVAL.
To correct problem: See the TROUBLE-
SHOOTING chart.
NOT,Te f
light may
also come on
when using
attachments,
due to
reduced
airflow
through the
attachment.
11
Alwaysfollowallsafetyprecautionswhen
cleaningandservicingthevacuum
cleaner.
ElectricalShockAndPersonalInjury
Hazard
Disconnectelectricalsupplybefore
servicingor cleaningthe unit.Failure
to do so could resuRin electricalshock
or personal injuryfrom cleanersud-
denlystarUng.
Gather the power cord and wrap it loosely
around the quick release cord hook and
lower cord retainer.
Store the cleaner in a
dry, indoor area, on
the floor with the
Quick
Release handle locked in the
Cord upright
Hook _ position.
Power
Lower
Cord
Unplug cord from wail outlet.
WARNING
dcal Shock And Personal Injury
Hazard
Wrappingthe cord too tightly puts
stresson the cord and can cause cord
damage. A damaged cord isan electri-
cal shockhazard and could cause per-
sonal injuryor damage.
DO NOT ddpwater on cleaner.
To reduce static electricity and dust build-
up, wipe outer surface of cleaner using a
clean, soft cloth that has been dipped in a
solution of mild liquid detergent and water,
then wrung dry. Wipe dry after cleaning.
Wash attachments in warm soapy water,
rinse and air dry. Do not clean in dishwash-
or.
Do not use attachments if they are
wet. Attachments used in dirty areas,
such as under a refrigerator, should
not be used on other surfaces until
they are washed. They could leave
marks.
12
Alwaysemptythe dust binwhen dirtlevel
reachesthe "MAX FILL" line.
TO REMOVE DUST BIN
! WARNING
Always unplugpower cord fromelectri-
cal outletbefore performingany ser-
vice on vacuum.
Lift dust bin han- DustBin _h_
Release
die located at the Handle --
top of the dust
bin. Dust
Bin --
J
Pull the handle
forward and lift
dust bin up and
out of the vacu-
um cleaner.
Seoondar,I
Remove any
clogs that
might be
located in the
dust bin port
or the sec-
ondary filter.
TO EMPTY DUST BIN
Turn This Direction Closed
To Open For Emptying (for Use)
Open
(For Emptying)
Rotate dust bin lid assembly counterclock-
wise as indicated on the lid and lift off.
Pour dust bin contents
into a trash container.
TO CLEAN FILTER
The filter may be
cleaned by
tapping it on a firm
surface or by
rinsing it under a
faucet. See Filter
Changing/Cleaning
section Rinse with
water only, do not
use any detergent or
_ Filter
Cover
soap. Allow the filter to dry for 24 hours
before putting it back into the vacuum.
13
TOREPLACEDUSTBIN
Turn This Direction Open
TO Close For Use (For Emptying)
Closed
(ForUse)
Place dust bin lid assembly back onto top of
dust bin. Align lid marks with bin marks as
shown above in Open (For Emptying).
Rotate lid clockwise while pressing down-
ward so that marks align as shown in
Closed (For Use).
Place dust bin
back into vacuum
cleaner by insert-
ing the bottom first
and tilt back with
the dust bin han-
dle raised.
Dust Bin
Release
Dust
Bin
Push forward and
lower the dust bin
handle to lock
dust bin in place.
Check secondary filter 'frequently and clean
when dirty.
Remove the dust bin as outlined in the
DUST BIN CLEANING section.
To clean filter screen wipe screen with a dry
cloth.
NOTE: Filter screen is not removable.
Replace the dust bin as outined in the
DUST BIN CLEANING section.
Secondary
14
WARNING
PRIMARY FILTER
Check primary filter frequently and clean
when dirty.
TO REMOVE PRIMARY FILTER
Remove the dust bin and dust bin lid
assembly as outlined in the DUST BIN
CLEANING section. While holding the pri-
mary filter over a trash container grasp filter,
rotate and lift off.
Clean primary filter by
gently tapping over a trash
container. Locking
Tap on several
sides to
ensure best
cleaning. Cover
Slot
Rinsewith water onlyas needed (see Dust
Bin Cleaning).
When cleaning the filter no longer restores
vacuum suction to full power you need to
replace the filter.
TO REPLACE PRIMARY FILTER
Make sure that the slots
of the filter line up with
the locking tabs on the
filter cover. Replace filter
and rotate filter until
slots lock onto tabs
in cover.
Cover
Slot
Tab
Note: Under normal use and care, your filter
can be expected to last up to 3 years.
Re-attach the filter cover and filter to dust
bin (see Dust Bin Cleaning). Place dust bin
back into cleaner.
EXHAUST FILTER
FOAM
Press inward on each side of
exhaust filter cover and pull out
to remove from vacuum
Press
cleaner. Inward
Exhaust
Exhaust
Remove the
frame and filter.
Push only on
filter frame, not
on filter itself.
Filter
Frame
Filter
Wash the exhaust filter in warm soapy
water; rinse and dry thoroughly by squeez-
ing the filter in your hand and letting it air
dry.
DO NOT wash in the dishwasher.
DO NOT installdamp.
Replace the exhaust filter, carefullyposition-
ing it so that it fits into the frame.
Exhaust
Filter
Cover
\
Replace the
exhaust filter
cover by placing
tabs in slots and
pushing in until
cover snaps into
place.
15
WARNING
ElectricalShock Or Personal Injury
Hazard
Disconnectelectrical supplybefore
servicingor cleaningthe unit. Failure
to do so couldresultin electricalshock
or personal injuryfrom cleaner sud-
denlystarting.
Frequently check and remove hair, string
and lint build-up in the brush area. If build-
up becomes excessive, follow the steps
below. Should the belt become loose or
should it break, follow the Belt Removal
Instructions.
TO REMOVE NOZZLE COVER
Disconnect electrical supply.
To protect the floor surface, always place
paper under the nozzle any time the nozzle
cover is removed.
Release the nozzle c_)ver by rotating the
nozzle cover retainerg to the UNLOCK
position. Grasp back of nozzle on each side
and lift up to remove it from nozzle cover.
Nozzle
Cover
Carefully remove any residue that may exist
in the belt area.
Personal InjuryHazard
Always unplugthe vacuum cleaner
before cleaningthe brusharea as agi-
tator may suddenlyrestart. Failureto
do so can resultin personal injury.
TO REMOVE BELT/CLEAN
AGITATOR
Agitator
Position hands on the agitator. If the belt is
still attached to the agitator, there will be
tension on it.
Carefully lift the right end of the agitator and
then lift the left end.
Remove the worn or broken belt from the
motor drive shaft.
Personal Injury Hazard
Be careful when removingthe agitator
as the belt tensionis high.Failure to
do so could resultin personalinjury
fromthe agitator releasingquicklyand
snappingaway.
16
Remove the agitator to check for string and
hair build-up.
NOTE: In order to keep cleaning efficiency
high and to prevent damage to your vacu-
um, the agitator must be cleaned every time
the belt is changed,
The agitator must also be cleaned accord-
ing to the following schedule:
Vacuum Use
HEAVY -
(used daily)
MODERATE-
(used 2-3 times/week)
LIGHT-
(used 1time/week)
Clean Aaitator
every week
every month
every 2months
Cap
Cut oft any carpet
pile, hair or lint
entangled around
the agitator and
remove any string
or debris located
near the end
caps.
TO REPLACE BELT
Shaft
_"New
Belt
Belt
Pulley
Seat left end of agitator into nozzle base. To
seat agitator end, place rounded portion of agi-
tator end cap down into slot in nozzle base.
Loop the new belt on the motor shaft.
NOTE: Use Belt #20-5275
Loop the other end of belt onto the belt
pulley on the right end of agitator.
Pull right end of agitator forward and seat it
into nozzle base
Agitator Nozzle
Base
End
Cap
--Base
Slot
Press firmly, checking to see that each
end is completely inserted.
Agitator
Check to see that the belt is centered on the
belt pulley and that the agitator turns freely.
Nozzle I
Cover
\
Nozzle Cover
Retainers
Make sure the nozzle cover retainers are in
the UNLOCK position. Hook the front of the
nozzle cover on to the nozzle base and
rotate downward. Once in place, rotate the
nozzle cover retainers to the LOCK position.
17
Electrical Shock Or Personal Injury
Hazard
Disconnectelectdcal supplybefore
servicingor cleaningthe unit, Failure
to do so couldresult in electricalshock
or personal injuryfrom cleaner sud-
denly starUng.
Always follow all safety precautions when
cleaning and servicing the vacuum cleaner.
If the cleaner does not seem to have ade-
quate suction, first check if the dust bin is
full or if a filter is clogged. See DUST BIN
CLEANING and FILTER CLEANING /
CHANGING.
If the dust bin and filter areas are free of
clogs, check the hose area. Remove the
suction inlet by depressing the two tabs that
secure it to the back of the vacuum and
check for clogging in this area.
Hose
Tabs
Inlet
Tool
Motor
Hose
Replace the suction inlet and remove the
other end of the hose from the tool holder.
Plug in the vacuum and turn it on. While
running the vacuum cleaner, stretch the
hose in and out to remove the clog.
Turn the unit off and unplug the unit.
If the clog still exists, pull the short hose out
of the tool holder and inspect the short
hose.
Remove any visible clogs.
Motor _-_ 1
Protector _ ;___
NOTE: Do not block motor protector.
This vacuum has a motor protector by-pass
valve which automatically opens to provide
cooling air to the motor when a clog
prevents the normal flow of air. If the by-
pass valve opens to prevent motor
overheating and possible damage to the
vacuum, a change of sound will be noticed
as air rushes through the valve opening. If
this occurs, turn the vacuum off and unplug
the power cord from the outlet. Then check
for clogs as described under the CLOG
REMOVAL section.
The motor protector by-pass valve may open
when using attachments or when cleaning
new carpet, due to reduced air flow caused
by the attachments themselves or by new
carpet fuzz filling the dust bin quickly.
18
ElectricalShockOr PersonalInjury
Hazard
Disconnectelectricalsupplybeforeser-
vicingor cleaningthe unit. Failureto do
socould result inelectricalshockor
personalinjuryfromcleanersuddenly
starting,
TO CHECK AGITATOR
Base Belt Guard
Turn the vacuum
over to check for
worn brushes.
When brushes are
worn to the level of
the base belt guard,
replace the agitator.
TO REPLACE AGITATOR
Remove the nozzle cover and agitator. See
BELT CHANGING AND AGITATOR
CLEANING.
Replace agitator with a new one.
Reassemble the belt, agitator and nozzle
cover. See BELT CHANGING AND
AGITATOR CLEANING.
Belt Pulley
t
End Cap
Agitator Unit
End Cap
19
SOME MODELS
CAUTION
ElectricalShock Or Personal Injury
Hazard
Disconnectelectrical supplybefore
servicingor cleaningthe unit. Failure
to doso couldresultin electricalshock
or personal injuryfrom cleaner sud-
denlystarting.
Disconnect electrical supply.
To access the light bulb, remove the screw
which secures the light lens to the vacuum.
Remove the lens.
Screw Push Here
ToRemove
Remove the light bulb by pushing the bulb in
while turning counterclockwise to release
from the slot. Pull the light bulb straight out.
\
Do notuse e bulb rated over 130 V
AC-15 W. Duringextended use, heat
from the bulbcouldoverheat surround-
ing plasticparts.
To replace the light bulb, carefully insert and
turn clockwise to fit securely into slot.
NOTE: See Parts and Features for Bulb
number.
I CAUTION
Do not plug in or turn on until corn-
pletely reassembled.
Position the light lens back on the vacuum.
Replace the light lens screw.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

Kenmore 116.34720400 Owner's manual

Category
Vacuum cleaners
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI