First Alert Channel/2 User manual

Brand: First Alert

Model: Channel/2

Category: Digital Video Recorders (DVR)

Type: User manual

This manual is also suitable for

USER’S MANUAL

Model

DVR0405 | DVR0410

DC4405-420

DC4205-420

Page 2

Welcome

Thank you for choosing First Alert for your security needs!

For more than half a century, First Alert has made the home-safety and security products that make

your job easier. Our products are built to the highest standard which has earned us a leadership role

in the home-safety and security product categories. We are committed to serving our customers,

from the professionals who install our products, to the families and businesses who count on them.

First Alert has been helping families and businesses stay safe for over 50 years. By having a First

Alert Security System, you’re taking the ﬁrst step in protecting your home or business from damage

or theft. We’re watching, even when you’re not.

This manual is written for the DVR0405 and security kits which include the DVR0405. It was accurate at

the time it was completed. However, because of our ongoing effort to constantly improve our products,

additional features and functions may have been added since that time and on-screen displays may change.

We encourage you to visit our website at www.brkelectronics.com to check for the latest manuals (English

and Spanish), ﬁrmware updates, downloads, other security camera products and announcements. You’ll

ﬁnd this product line under Home Security >> Security Cameras >> Wired Cameras.

INTRODUCTION

THANK YOU

Corporation (NYSE: JAH). First Alert® is a registered trademark of the First Alert Trust. Due to continuing product development, the product inside

the packaging may look slightly different than the one on the package. To obtain warranty service, contact the Consumer Affairs Division at

1-800-323-9005, Monday through Friday, 7:30 a.m. - 5 p.m., Central Standard Time.

Made in China

Page 3

INTRODUCTION

KEY PRODUCT FEATURES

Main Description

Four channel H.264 digital video recorder with Internet remote

surveillance, motion detection, PTZ and alarm control suitable for

applications such as high-end residential - new or remodel, light

commercial, small business/retail, small warehouse or small grocery.

Product Features

• H.264 Compression & Virus free Linux O/S

• Record, playback, mobile phone live view, backup, control, & remote access

• 500GB SATA hard drive installed

• Supports smart phone live view & E-mail alarm

• Customizable E-mail alerts

• Supports 4-channel HD1 & CIF or 2-channel D1 and

6-channel CIF Real-time simultaneous recording

• Supports 4-channel simultaneous playback

• User-friendly interface: 16 bit true color DVR, GUI

with notes for selected menu items

• Advanced motion detection activated recording

• 24/7 Scheduled Recording

• Supports D1,HD1& CIF for recording quality

• Network monitoring through internet access

• Supports USB or external DVD backup

• Hi-speed backup/upgrade/record via USB2.0

• PTZ camera control

Connect wireless camera to wired DVR security system

Go to www.ﬁrstalert.com/howtoconnect

Page 4

Section DeScription

page

umber

Introduction 2-3

Safety 6

Product Overview 7

What is in the Box 7

DVR Controls

Front Panel 8

Back Panel 9

Remote Control 10

Mouse Controls 11

Camera Power Connections 12

Connecting Devices 12

Initial Setup - System Operation 13

System Start Up 13

Power On/Off 13

Main Menu Access (Quick Access Menu) 14

Password Setup and User Permissions 15

Camera Display Setup 16

Language, Date and Time 17

Display, Video/Audio 17

Language, Date/Time and Daylight Savings Time (DST) 17

Basic Operation 18

Recording 18

Conﬁgure Recording Options 18

Recording Schedule (Timer Recording) 18

Recording Schedule (TIMER RECORD) Example 19

Privacy Mask Field 19

Motion Detect Setup 19

Playback 20

Playback and Record Search 20

On-Screen Playback Controls 20

File List 21

Backup 21

HDD Management 21-22

INTRODUCTION

TABLE OF CONTENTS

Page 5

INTRODUCTION

TABLE OF CONTENTS

Section DeScription

page

umber

Advanced Operation 22

Alarm 22-23

Alarm Setup 22-23

E-mail Setup 23

System Info and System Update 24

System Maintain 24

Upgrade Firmware 24

PTZ Setup and Control 25-26

Step 1: Connect your PTZ Camera to this DVR 25

Step 2: Conﬁgure PTZ Communication Settings 25

Step 3: Conﬁgure the Operation and Control of your PTZ Camera(s) 25

Step 4: Conﬁgure the CRUISE SETTING of your PTZ Camera 26

Remote Access 27

Network Setup for Remote Access 27

DHCP (Dynamic Host Conﬁguration Protocol) 27

Static IP 27

UPnP (Universal Plug and Play) 28

PPPoE (Point-to-Point Protocol Over Ethernet) 28

DDNS (Dynamic Domain Name Service 29

Port Forwarding 30

Remote Surveillance 31

Remote Surveillance using Internet Explorer 8 31

Using Remote Surveillance 32

Remote Surveillance Main Screen 33

Live Viewing Tab 34

Playback Tab 35-36

Setup Tab 37

Setting, Maintenance and Host Info Tabs 38

Mobile Phone 39

Mobile Setup 39-40

Appendix 41

Hard Drive Removal and Installation 41

Speciﬁcations 42

Notes 43

FAQ’s (Frequently Asked Questions) 44-45

Troubleshooting 46

Warranty 47

Page 6

SAFETY

CAUTION STATEMENTS

Safety Precautions

• Do not drop, puncture, or disassemble the cameras or DVR.

• Do not tug on the power adapter. Use the plug to remove it from the wall.

• Do not expose the cameras or DVR to high temperatures.

• For your own safety, avoid using the DVR when there is a storm or lightning in your area.

• Use the cameras and DVR with care. Avoid pressing hard on the cameras or DVR body.

• Do not use power cable if crushed or damaged.

FCC Compliance Class B Digital Device

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that of the receiver.

• Consult the dealer or an experienced radio or TV technician for help.

Notice: Only peripherals complying with FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals

or peripherals not recommended by First Alert / BRK Brands, Inc. is likely to result in interference to radio and TV reception. Changes or

modications to the product, not expressly approved by First Alert / BRK Brands, Inc., could void the user’s authority to operate the equipment.

Important: The information shown in the FCC Declaration of Conformity paragraph below is a requirement of the FCC and

is intended to supply you with information regarding the FCC approval of this device. The phone number listed below is for

FCC related questions only and not intended for questions regarding the connection or operation for this device.

FCC Declaration of Conformity for devices with the FCC logo. Responsible Party: First Alert / BRK Brands,

Inc., 3901 Liberty Street Rd., Aurora, IL. 60504-8122. Telephone: (630) 851 - 7330. Product / Model: DVR0405

We, First Alert / BRK Brands, Inc. declare under our sole responsibility that the device to which this declaration relates: Complies with

Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Certiﬁcation (if applicable)

This device contains a radio transmitter. Accordingly, it has been certied as compliant with 47 CFR Part 15 of the

FCC Rules for intentional radiators. Products that contain a radio transmitter are labeled with an FCC ID.

FCC Compliance

These symbols indicate that it is prohibited to

dispose of these batteries in the household

waste. Take spent batteries that can no

longer be charged to the designated

collection points in your community.

Disposal

Fire and Electric Shock Hazard Statement

Caution!

When working with electrostatic sensitive

devices such as hard disk or DVR unit, make

sure you use a static-free workstation. Any

electrostatic energy coming in contact with the

hard disk or DVR can damage it permanently.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

UNPLUG ALL POWER SOURCES, INCLUDING CAMERAS

FROM THE DVR BEFORE REMOVING COVER. FAILURE

TO DO SO CAN RESULT IN DAMAGE TO THE DVR OR

ITS COMPONENTS AS WELL AS INJURY OR DEATH.

The lightning ash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of un-insulated

“dangerous voltage” within the product’s enclosure that may be of

sufcient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle, is intended to

alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS UNIT TO RAIN OR MOISTURE

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF THE PLUG TO THE WIDE SLOT AND FULLY INSERT

CAUTION

RISK OF ELECTRIC SHOCK

Page 7

PRODUCT OVERVIEW

PACKAGE CONTENTS

What

s in the Box

4 Channel Digital DVR

with 500GB or 1TB Hard Drive

USB 2.0 Mouse

3 Window

Warning Decals

Power Supply for

DVR and Cameras

RJ45 Ethernet Cable

BNC Video & DC Power Cable

DC4405-420: 4 Cables

5-way Power splitter -

4 cameras, 1 DVR

Quick Install Guide

Remote Control

Installation Software

Page 8

PRODUCT OVERVIEW

DVR CONTROLS

Front Panel

item Function control DeScription

Power/Standby Press to enter standby mode or Power up DVR

IR Sensor IR receiver for the remote control

MENU/EXIT Press to open/close the main menu

LED Indicators Shows status of Link, 100M, Full, Alarm, Record, HDD.

Channel Numbers/

Playback

Press buttons 1~4 to view the selected channel in full-screen. Pressing

buttons 5~9 returns screen to 5 camera display mode.

USB

Connect a USB ﬂash drive to the top port for data backup and ﬁrmware

upgrades. Connect a USB mouse to the bottom port

Navigation/OK/PTZ

In menus, press to conﬁrm selections; in PTZ mode, press to change the

navigation buttons to control the connected PTZ camera (not included)

Press to move cursor up; in PTZ mode, press to pan camera up.

Press OK to start motion.

Press to move cursor down; in PTZ mode, press to pan camera down.

Press OK to start motion.

Press to move cursor left; in PTZ mode, press to pan camera left.

Press OK to start motion.

Press to move cursor right; in PTZ mode, press to pan camera right.

Press OK to start motion.

Page 9

PRODUCT OVERVIEW

DVR CONTROLS

Back Panel

item Function DeScription

POWER Input DC 12V/5A power connection

Network For connecting RJ45 ethernet cable to PC or router

VGA Output For connecting to a VGA monitor

Video Output For connecting to a BNC monitor (800 x 600)

Alarm Input 4 alarm inputs

Alarm Output Output for alarm

RS485 For connecting PTZ cameras

+12V Power supply for DC relay, the current is 100mA (to prevent short circuits)

Audio Input

For connecting audio signal from audio capable cameras or self powered

microphones (RCA jacks)

Audio Output For connecting audio signal to ampliﬁed speakers (4 RCA jacks)

Video Input For connecting video signal from cameras (BNC)

Power Switch Power On/Off

Ground Ground connection

Page 10

Remote Control

Remote Control Operation

The remote control is the secondary input device for navigating the system’s interface.

In device operation, the enter key has the same function as “left click” of the mouse.

PRODUCT OVERVIEW

REMOTE CONTROL

item Function DeScription

STANDBY Press to turn standby mode ON/OFF

If “Security” has been enabled in the setup menu, press

to open the user password login screen.

Number/Channel

Buttons

While in menus, press buttons 0~9 to enter values; dur-

ing live viewing, press to view channels in full-screen

Window

Display

Press to switch between quad and split-screen displays

MENU Opens the main menu

PTZ Press to open the PTZ control window

EXIT Close menu windows

Navigation/

In menus, press to conﬁrm selections; in PTZ mode,

press to change the navigation buttons to control the

connected PTZ camera (not included)

Press to move cursor up; in PTZ mode, press to pan

camera up. Press OK to start motion.

Press to move cursor down; in PTZ mode, press to pan

camera down. Press OK to start motion.

Press to move cursor left; in PTZ mode, press to pan

camera left. Press OK to start motion.

Press to move cursor right; in PTZ mode, press to pan

camera right. Press OK to start motion.

+ / - In menus, press to adjust values

RECORD Press to start manual recording

STOP Press to stop manual recording

EXTRA For future use

Playback

Controls

Increase reverse playback speed 2X, 4X, 8X

Press to freeze playback to one frame, then press again

to advance frame-by-frame

Press to start playback

Press to slow playback speed by 1/2, 1/4, 1/8

Press to increase forward playback speed 2X, 4X, 8X

Remote Control

TIP: When using

the remote control

to enter password

and camera titles,

select the ﬁeld using the navigation

buttons, press OK, and then press

the number buttons.

Directions for Installing/

Changing Batteries

1. Open battery compartment on back of

Remote and insert (2) Alkaline

AAA batteries (provided.)

2. Ensure all batteries are installed correctly

with regard to polarity (+ and -.)

3. Remove batteries from Remote if it is not

to be used for an extended period of time.

4. Remove used batteries promptly and replace

all batteries of a set at the same time.

5. Always purchase the correct size and grade

of battery most suitable for intended use.

Page 11

PRODUCT OVERVIEW

MOUSE AND VIRTUAL KEYPAD

Mouse Operation with this DVR

The mouse is the primary input device

for navigating system menus.

NOTE: Unless otherwise noted, all system functions described

in this manual are achieved through mouse input.

To use a mouse with the system:

Connect a USB mouse to the USB MOUSE

port on front panel of the system,

NOTE: Only the USB 2.0 port on the

front panel is designed for data backup

to a USB ﬂash drive. Do not connect

a USB ﬂash drive to the USB MOUSE port.

Use the mouse buttons to perform the following:

Left-Button:

• Click to select a menu option

• During live viewing in split-screen double-click on a

channel to view the selected channel in full-screen

• Double-click the channel again to

return to split-screen view

• Selecting letter or number on the virtual keypad

Right-Button:

• Click to open the Quick Access Menu

• Exits any window

• Exits any menu or re-opens previous menu

Scroll-Wheel:

• Forward-switch to VGA; backward-switch to BNC (CVBS)

Mouse Controls

DVR Front Face

Connect Mouse &

USB Drive

Mouse Button Operation

Virtual Keypad

To enter text or numerical data, the system uses a virtual

keypad. In ﬁelds where letters or numbers can be entered,

you can switch between various formats – numbers, upper

case (ABC) and lower case (abc). Note you can access all

numbers when in the “Letters” virtual keypads. See below.

Numbers

Letters-Uppercase

Letters-Lowercase

Page 12

Installing Cameras

Mounting Cameras and Running Cable

Select the position for the camera and secure the camera stand. Screw the camera onto the stand. Adjust camera to the proper

view angle. Make sure the lens is upright relative to the subject. Tighten the thumb bolt. First Alert cameras can be either ceiling or

wall mounted by simply reversing the camera stand mounting. See “Camera Orientation” Info box. Holes are provided on both the

top and bottom of the camera housing to accommodate most mounting requirements. Run cable from camera to DVR location. See

Information box below on “Longer Cable Runs”.

Camera Orientation

It’s important the camera is mounted correctly to

ensure the image is not upside down as the cam-

era lens can only be positioned one way.

Longer Cable Runs

Longer cable runs may require an upgrade to

RG59 Coax cable. First Alert kits ship with eco-

nomical AV cable that is designed to work well up

to the length of cable provided, usually around

60 feet. If longer distances between camera and

DVR are required, you will need to upgrade to RG59 Coax cable. We

provide several lengths up to 300 feet. In addition, if you need to run

cable for in-wall installations, then you may require ﬁre rated cable,

FT-4/CMR UL approved for in-wall installations.

Connecting Devices

5 Way Splitter -

4 camera/

1 Power

Video to DVR

Channels 1-4

Video to Camera

Power to Camera

Power to DVR

Power to Cameras

Power

from 120V

DC Converter - 12V

AV Cable: BNC/

DC Power

(1 per Camera)

VGA to PC Monitor or TV

BNC to Security Camera Monitor

(Not included)

RJ45 Ethernet

to Router and

Internet

PTZ & Alarm

Connections

(Cameras not

included)

Follow this diagram to make device connections. Note, some devices are

not included with this kit. See “What’s in the Box” for included devices.

DVR Front Face

Connect Mouse &

USB Drive

PRODUCT OVERVIEW

CAMERA AND POWER CONNECTIONS

RCA Audio In from Audio

Cameras or Powered

Microphone

(Not included)

RCA Audio Out to

Powered Speakers

(Not included)

Smartphone

through Mobile

Internet Setup

(Smartphone Not

included)

Camera - Wall Mounted

Camera - Ceiling Mounted

Page 13

System Start Up

Default Video Output

The default video output for the DVR system is VGA. If you connect a

BNC (CVBS) monitor on initial setup, you will need to use the mouse

“Scroll Wheel” to switch to the BNC output to be able to use the

mouse. Roll the mouse “Scroll Wheel” backward to go to BNC and

forward to go to VGA. The REMARK screen is shown on startup.

Power On/Off

To power the system On/Off, connect the power

cable to the DC 12V port on the rear panel. Flip

the toggle switch on in the back of the DVR. At

startup, the system performs a basic system

check and runs an initial loading sequence.

After a few moments, the system loads a live

display view.

Standby Mode

The system can also be put into Standby Mode. Power will remain to the

system but will not be recording. To start/stop Standby Mode:

1. Press and hold the POWER button on the front panel or remote control

until the prompt closes. The system enters standby mode.

2. To exit standby mode, press and hold the POWER button on the front

panel or remote control until the system beeps. The system will begin

powering up.

User Login

Password

ATTENTION: By default, passwords are disabled on the system. You do not

need to enter a password when accessing any system menus. However, for

security purposes, it is highly recommended to enable passwords on the

system using the Password Menu. See “Password” section for details on

setting up passwords. Click APPLY to proceed to the MAIN MENU.

Switch between VGA to BNC Output

INITIAL SETUP

SYSTEM OPERATION

Standby Mode

User Login Menu

Power Switch

Page 14

Main Menu Access

To open the Main Menu: Right-click anywhere on-screen to open the Quick Access Menu and select MAIN MENU (mouse only), or

press the MENU button on the remote control or front panel of the system.

NOTE: If passwords are enabled on the system, you need to select your Device ID and enter 1-8 digits numerical password to open

the Main Menu.

Main Menu

1. SEARCH: Search for recorded video on system.

2. RECORD: Conﬁgure recording parameters (quality, resolution), set

record modes, and enable/disable audio recording. Note: Audio capable

cameras (not included) are required for audio recording on the system.

3. HDD: Display hard drive status and format the

internal hard drive of the system.

4. BASIC: Open the Basic Setup Menu, which lets you set the

system language, date and time, device IDs and passwords,

and conﬁgure display, audio and video settings.

5. ADVANCED: Opens the Advanced Setup Menu, which

lets you view system info, conﬁgure alarm, PTZ, motion

detect, maintenance, mobile, and network settings.

6. EXIT: Closes the Main Menu.

7. Displays information about the contents of the selected Main Menu icon.

Main Menu

Quick Access Menu

When using the mouse, use the Quick Access Menu to access several system

options, including the Main Menu. Select one of the following options:

• MAIN MENU: Opens the main system menu

• KEYLOCK: Requires a password for admission to menu

• CHN SWITCH: Select type of split-screen display or Quad to display all cameras

• VIDEO SEARCH: Open the Search Menu to view recorded video

• PTZ : Opens the PTZ control menu

• MUTE: Mutes audio on the system

• MANUAL REC: Start manual recording

• STOP REC: Stop manual recording

• ROTATION: Displays each camera sequentially in full screen mode.

The time is set by the “loop time” in the Video/Audio menu.

• START CRUISE: Click to start preset PTZ Camera motion

• STOP CRUISE: Click to stop preset PTZ Camera motion

• STANDBY: Puts system in standby mode.

To close the Sub-Menu, click anywhere on-screen.

initial setup

system operation

Main Viewing Screen

Showing No HDD in DVR

Live View Screen

The Live View Screen is the home or main viewing screen. It shows live video of all

current cameras connected to the DVR. You can double-click a channel at any time

to view it in single-channel mode. You access all menus from this Live View screen

via the Quick Access Menu. You will also see the Channel number or name, time

and day information (see page 16 “Camera Display Setup” for customizing the Live

View Screen). It is also where you will see various information and warning icons,

depending on what is happening in the system or with the alarms that may be set.

【R】 means the channel is recording

【M】 means motion detection alarm activated on the channel

【I】 means an input on the alarm block activated on the channel

【H】 means either the hard drive is not installed, it is bad or it is full

【B】 means Tamper Alarm has been activated on the channel

No HDD installed

NOTE: If there is no HDD installed, or the HDD is not recognized, or the HDD is not formatted in Live

View a red【H】will be displayed in the video preview interface. You must format the HDD in the DVR

before ﬁrst use. See: Menu > HDD management > Format. After formatting, the system will restart.

Page 15

Password Setup

Setting Up Passwords & User Permissions

When you ﬁrst startup your DVR, you are automatically logged in as the ADMIN. By default, passwords

are disabled on the system. You will not need a password to log in or access menus. You will not

need a password to access your system using the browser-based remote software.

The system employs two levels of user authorities connected to a Device ID. The levels are as follows:

1. ADMIN (administrator): Has full control of the system, and can change both administrator

and user passwords and enable/disable password checking

2. USER (normal user): Only has access to live viewing, search, playback, and other limited authorities.

For security reasons, it is highly recommended to enable passwords on your system. If you enable passwords, you must select

from 1-8 digits. The ADMIN and USER passwords must not be the same.

To customize PASSWORD settings, click BASIC from the Main Menu, then click

PASSWORD. You are now in the User Setup menu. From here you can change the

DEVICE ID:

1. Device ID: Click the ﬁeld beside Device ID and enter a 6-digit

numerical Device ID using the Virtual Keyboard.

Next, in the USER SETUP Menu click CONFIG to set up users. NOTE: Only the

administrator can set permissions. Users can enter conﬁg to change their

password. You can change the

• STATE: active or not Allows ADMIN to set USER as ACTIVE or INACTIVE.

• USER NAME: Assign or change user name using the virtual keyboard.

• PASSWORD ENABLE: enable or disable the password for this user

• PASSWORD: Password must be 1-8 digits

• CONFIRM: conﬁrm the password

• PERMISSION: Select all permissions for this user. (NOTE: this option is not

available for ADMIN as they have all permissions). Available choices are:

Record Setup, HDD Manage, Language Setup, Time Setup, Start/Stop

Record, Display Setup, Alarm Setup, System Info, Motion Detect, Mobile

Setup, System Setup, PTZ Setup, Network Setup, Video/Audio Set, IE

Preview for each of 4 Channels, Playback for each of 4 Channels.

Navigate the PERMISSION Screens by:

• NEXT: Moves to next selecting page.

• ALL: Selects all permissions.

• CLEAN: Clears all permissions.

NOTE: This page is working for administrator.

Administrator can assign permissions for user. User just

can see but can not change their permissions.

Multi User Login

After Users are set up, Select active user from USER NAME drop down

box to log on with previously set up permissions. The active user(s) will

be available. Next, key in the device ID and user password.

User Setup

User Password Setup

User Permission Screen 1

User Permission Screen 2

User Login-Multi Users

initial setup

system operation

Page 16

INITIAL SETUP

SYSTEM OPERATION

Camera Display Setup

Setting Up Cameras for Viewing and Recording

Use the Display Setup menu to customize channel titles, show/hide the date

and time in live viewing and playback, and enable/disable preview channels. To

customize Display settings, click BASIC from the Main Menu, then click DISPLAY:

Display

1. Conﬁgure the following options:

• NAME: Click any of the ﬁelds and enter a new title for the

selected channel using the Virtual Keyboard (mouse only)

• POSITION: Reposition the channel title; select TOPLEFT,

BOTTOMLEFT, TOPRIGHT, BOTTOMRIGHT, or OFF. If OFF,

the title will not be displayed for the selected channel

• COLOR: Adjust CHROMATICITY, LUMINOSITY, CONTRAST,

and SATURATION for the selected channel

• LIVE: This feature can be very useful if your display monitor

is in public view. With LIVE in the OFF selection that channel

will appear black on the display to give the impression that

no cameras are connected and the system is not recording.

Select ON/OFF to enable or disable this feature

• PREVIEW TIME: Select ON/OFF to show/ hide

the date and time during live viewing

• RECORD TIME: Select ON/OFF to show/hide

the date and time during playback.

2. Scroll down to change the settings for the remaining channels

3. Click APPLY to save your settings. Click OK in

the REMARK window. Click EXIT.

Video/Audio

Use the Video/Audio menu to set the resolution and camera setup

on the system. To conﬁgure Video/Audio options:

1. Under VGA RESOLUTION, select 800 x 600, 1024 x 768, 1280 x 1024,

1366 x 768, 1440 x 900.

2. Under CAMERA SYSTEM, select NTSC or PAL. (See info box below)

3. Under LOOP TIME (SECOND), enter with virtual keypad from

1 to 300. Loop Time speciﬁes the amount of time the channel

is displayed before moving to the next channel. Used in

conjuntion with “Rotation” in the “Quick Access Menu”

4. Under VOLUME SETUP, adjust slider from 0 to 63. Click X to save.

5. Under MARGIN, adjust TOP, BOTTOM, LEFT, RIGHT

margin with slider from 0 -10. Also adjust Display from

VGA or CVBS. Default is VGA and 0 for all margins

6. Click APPLY. Click OK in the REMARK window.

7. Click EXIT in all menus until all windows are closed.

Color Set-up

Video/Audio Menu

Audio/Video Recording

Caution: Audio surveillance in some

states is illegal or requires permission

from one or all parties to record

someone’s voice. Laws are also

different from residential vs. commercial applications.

Some federal, state, and local laws prohibit certain

surveillance activities and/or the use or distribution of

the information obtained from such activities. Prior

to using this system, you should become familiar with

the pertinent laws to ensure compliance with those

applicable to surveillance activities.

NTSC or PAL?

NTSC (National Television Standards Committee)

is the video system or standard used in North

America and most of South America. In NTSC, 30

frames are transmitted each second. Each frame is

made up of 525 individual scan lines.

PAL (Phase Alternating Line) is the predominant video system or

standard mostly used overseas. In PAL, 25 frames are transmitted

each second. Each frame is made up of 625 individual scan lines.

Display Setup Menu

Page 17

Language, Date and Time

Setting Up Language/Date/Time

Set the system language, date and time, passwords, and conﬁgure audio

and display options. The Basic Setup Menu contains the following sub-

menus: Language, Date/Time, Password, Display, and Video/Audio.

Language

To change the system language:, from the drop-down menu select LANGUAGE.

Click APPLY. Click CLOSE in the conﬁrmation

window. Click EXIT to close the menu.

NOTE: The system will restart when you ﬁnish system

language setup. The default is English.

Date/Time

It is highly recommended to immediately set the date and time

when ﬁrst setting up your system. To set the date and time:

1. Click DATE/TIME and conﬁgure the following options:

• DATE: Enter the day, month, and year.

• DATE FORMAT: Select DD/MM/YYYY, MM/DD/YYYY, or YYYY/MM/DD

• TIME: Enter the time

• TIME FORMAT: Use the drop-down menu and select 12HOURS

or 24HOURS. If 12HOURS is selected, then set AM or PM.

• DST: Use the drop-down menu to select ON/OFF to enable/disable

Daylight Savings Time. See below for details on setting DST.

2. Click ZONE to enter your time zone from -12 to +12. To ﬁnd your time zone

visit www.worldtimezone.com or other similar sites.

See Info box for US codes.

3. Click SAVE DATE AND TIME. The new date and time are saved. Click EXIT.

Daylight Savings Time (DST)

To set daylight savings time:

1. Under DST, select ON. DST options appear.

2. Under DST MODE select one of the following:

• DEFAULT: The Default setting will apply the United States daylight savings time period from

the second Sunday of March to the ﬁrst Sunday in November (go to step 3)

• CUSTOM: Set customized start and end times for DST (go to step 4)

3. If using the DEFAULT, click APPLY. Click EXIT.

4. If setting a CUSTOM DST, use the drop-down menus to select a week and month for the start and end times.

5. Click APPLY. Click CLOSE in the conﬁrmation window.

6. Click EXIT in each menu until all windows are closed.

Basic Setup Menu

System Language Menu

US World Time Zones - UTC Codes

UTC stands for Universal Time Coordinates

or Greenwich Mean Time (GMT)

Eastern: -5

Central: -6

Mountain: -7

Western: -8

Alaska/Hawaii: -9 through -11

System Time/Date Setup

Why Set a Date & Time?

It’s important to set the proper date and time before continuing so that you can easily locate recorded events.

Inaccurate dates and times on ﬁles may affect their admissibility as evidence in court. In addition, when

changing current time settings, to avoid possible confusion with the time stamps on recorded and currently

recording ﬁles, stop all ongoing recording processes before altering the system time and restart recording

using the new settings.

INITIAL SETUP

SYSTEM OPERATION

Page 18

BASIC OPERATION

RECORDING

Recording

RECORD Mode

Conﬁgure Recording Options:

You have three recording options: Continuous, Schedule and Motion. By

default, the DVR is set to record continuously. Set parameters as follows:

1. From the Main Menu click RECORD. Under SWITCH, use the drop-

down menus and select ON/OFF to enable/disable recording from the

selected channel. Note: If SWITCH is set to OFF, then Motion Detect,

Alarm and Manual Record are also disabled for that channel.

2. Under RESOLUTION, select CIF, HD1, or D1.

NOTE: NTSC: @30fps, PAL: @25fps. Recording capabilities for

both NTSC & PAL: Channels 1-4: D1, HD1, CIF.

The ratios of D1, HD1 and CIF are as follows: 1 D1= 4 x CIF, 1 HD1 = 2 x CIF.

3. BITRATE (Kbps): See table for details.

4. FRAMERATE: Choose the recording frame rate 1-30, (fps – frames per

second). The lower the value, the less life-like and more jerky the recorded

movements will be. However, a lower frame rate uses less HDD space. Make

your choice depending on the precision with which you want to follow the

events being recorded. Frame-rate of each channel can be adjusted but is

limited by the total resources available. The total frame rate for all channels

combined cannot exceed 420 (NTSC) fps. Note: Although the chipset is NTSC

480, part of the resources are used for other internal functions and cannot be

allocated to recording resources.

AUDIO, select ENABLE or DISABLE. If audio recording is enabled, the system

will record audio from connected audio capable cameras (not included).

See caution statement on audio recording in Video/Audio section.

5. REC. MODE, select POWER UP or TIMER RECORD. If you select POWER UP,

the system will record continuously when the system is powered on. If you select

TIMER RECORD, you have to set a recording schedule on the system. Setting

TIMER RECORD to No RECORD does not disable the ability to Manual record.

6. REC. SIZE (Record Size), select 15MIN, 30MIN, 45MIN, or 60MIN.

NOTE: Record Size sets the ﬁle size for recorded video ﬁles on the system. Instead of recording data as one large ﬁle,

the system will divide the data into blocks of 15, 30, 45, or 60 minutes. This makes the recorded data easier to search

7. MASK FIELD lets you block a speciﬁc portion of a channel you do not want recorded or shown on the display

screen. This can be useful if you need to conceal a sensitive area

being captured by the camera. See next section for details.

8. Click APPLY. Click OK in the REMARK window. Click EXIT.

Recording Schedule (TIMER RECORD)

You can program the DVR to record according to a customized recording

schedule. The Schedule Grid shows the days of the week and hour blocks

00~23. You can set Alarm Recording (Red), General Recording (Green), or No

Recording (Blue) to each time block of each day. To set a recording schedule:

1. Open the Main Menu and click RECORD.

2. Under REC. MODE, select TIMER RECORD.

3. Click SCHEDULE. The Schedule menu opens.

4. Under CHANNEL, select speciﬁc channels or select ALL.

5. Below the grid, click either ALARM (red), GENERAL

(Green), or NO RECORD (Blue) and then click a time block on the desired day.

6. Use the FROM/TO drop-down menus to copy the schedule of one day to another. For example, if you want your schedule

for Monday to be the same on Wednesday: under FROM select MON, under TO select WED, and then click COPY.

7. Click APPLY. Click OK in the REMARK window. Click EXIT.

Record Menu

CCTV Resolution

CCTV resolution is measured in vertical and horizontal pixel dimensions and typically

limited by the capabilities of both the camera and the recorder that you are using for

your CCTV surveillance installation. CCTV systems use an analog video signal. For

television speciﬁcations (which CCTV uses) the highest resolution that can be captured

and stored is 704 x 480 (NTSC for the United States) and 720 x 576 (PAL for Europe). This resolution

is known as D1 resolution. A high end CCTV recorder is capable of recording at up to D1 resolution.

CCTV Resolutions

D1: 704 x 480

HD1 (2CIF): 704 x 240

CIF: 352 x 240

QCIF: 176 x 120

Bitrate in Kbps

Image

Quality

Low Medium High

CIF

384 512 768

HD1

512 768 1024

896 1024 1280

Basic Setup Menu

Basic Setup

Use the BASIC SETUP menu to conﬁgure language, date and time settings,

password setup, along with display, video and audio settings. You can also exit

the system through this menu. The Basic Setup menu contains the following

sub-menus: Language, Date/Time, Password, Display, Video/Audio and Exit.

Recording Schedule

Page 19

BASIC OPERATION

RECORDING

Recording Schedule (TIMER RECORD) Example

Privacy Mask Field

MASK FIELD lets you block a speciﬁc portion of a channel you do not want

recorded or shown on the display screen. This can be useful if you need

to conceal a sensitive area being captured by the camera. One contiguous

area can be MASKED within a channel. To use Privacy Mask Field:

1. From the Record menu, click MASK FIELD. The Mask Field menu opens.

2. Choose a channel you wish to apply the Mask Field.

3. Select ON from the SWITCH drop-down menu.

4. Click SETUP. The Mask menu will be replaced by the full-screen camera view

of the desired channel. Using the mouse, click and drag the cursor over the

area you want to conceal. A single click will produce a small black square.

Extend the square by dragging the cursor left, right, up or down as desired.

5. Right-click anywhere on the screen to return to the Mask Field menu.

6. Click APPLY. Click OK in the REMARK window. Click EXIT.

Motion Detect Setup

You can conﬁgure motion detection for each channel (Camera) connected to the

DVR. To conﬁgure motion detection:

1. From the Main Menu click ADVANCED. Then click MD (Motion Detect).

2. Under STATUS, select ON to enable motion

detection for the desired channel.

3. Under SENSITIVITY, select 1 through 8. The higher the

number, the more sensitive the motion detection.

4. Under MD AREA SETUP, click SETUP. The red motion grid

appears over the selected channel in full screen.

5. Click the blocks in the grid to enable/disable motion detection.

Red=motion detection enabled; Clear=motion detection disabled.

6. Right-click anywhere on the screen to return to the Motion Detection menu.

7. Click EMAIL, then select ON/OFF to turn on e-mail notiﬁcation.

E-mail must be conﬁgured. See manual for details.

8. Click BUZZER to turn audible notiﬁcation of motion ON/OFF.

9. Click APPLY. Click OK in the conﬁrmation window.

10. Click EXIT in all menus until all windows are closed.

NOTE: You can disable the MD buzzer in the Alarm Setup menu.

When MD is triggered, in the Live View Screen you will see a red【M】

in the Channel with a MD warning. You may also see a【R】if you

set up the channel to record when an alarm is triggered.

You want your system to record continuously on all channels

from 9 AM to 5 PM Monday to Friday. You also want Alarm/

Motion recording from 5 PM to 9 AM. You do not want the system

to record Saturday or Sunday:

1. Open the Schedule menu.

2. Under CHANNEL, select ALL.

3. Click the blue NO RECORD block below the

grid. A checkmark will appear in the block.

4. Under SUN, click blocks 00~23. The blocks will turn blue.

5. Under FROM, select SUN. Under TO

select SAT, and then click COPY.

6. Click the red ALARM block below the grid.

7. Under MON, click blocks 00~08 and blocks

17~23. The blocks will turn red.

8. Under FROM, select MON. Under TO select

TUE, and then click COPY. Repeat for Wednesday,

Thursday, and Friday. Your completed schedule

should the same as the schedule to the right.

9. Click SAVE. Click OK in the conﬁrmation window.

Click EXIT in all menus until all windows are closed.

Recording Schedule

Motion Detect Menu

Motion Detect Grid

Page 20

BASIC OPERATION

PLAYBACK

Playback

PLAYBACK Mode

Playback and Record Search

View recorded video on the system through the RECORD SEARCH Menu. To begin playback:

1. There are two ways to access the RECORD SEARCH menu. Right-click anywhere on the screen and select VIDEO SEARCH

from the Quick Access Menu. The RECORD SEARCH Menu opens. Or from the Main Menu select RECORD SEARCH.

NOTE: When you ﬁrst open the RECORD SEARCH

Menu, it displays the current month and date.

2. Click PLAY to playback the last minute of recorded video (Quick

Search) OR Under CHN select a speciﬁc channel or select ALL.

3. Under DATE, enter a date using the Virtual Keyboard (mouse only).

4. Click SEARCH. Recorded events on the system appear in red (alarm events—

includes both alarm and motion events) and green (normal recording).

5. Click a date in the Month Grid to search for video ﬁles.

6. Click a time block in the Hour Grid to view the video. Playback begins.

7. Move the mouse slightly to display the on-screen play back controls. You can

also use the playback control with buttons on the remote control or front

panel of the system.

On-screen Playback

Controls

To use the on-screen playback controls:

1. Click the VCR-like

controls to play, pause,

fast forward, rewind,

and

slow down playback.

2. Drag the slider to adjust

the volume (audio capable

camera required,

not included). Select

the box to mute the audio.

3. Click X to quit

playback and

return to the Search menu.

9. Under RECORD STATE, the system shows

recorded events in a Month Grid and a Time Grid. The selected day of the month will be outlined in

red. Green=normal recording; Red=alarm recording (includes both alarm and motion events). Click a

date in the month grid to view recorded video ﬁles for that selected date in the hour grid.

File List

Use the FILE LIST sub-menu to see a detailed list of all the recorded video on your

system. To open the FILE LIST:

1. From the RECORD SEARCH Menu, click SEARCH to search the system for

recorded video.

2. Click FILE LIST at the bottom of the menu. The FILE LIST menu opens.

To use the File List:

1. Under TYPE, select NORMAL to view only normal recordings,

ALARM, to view alarm recordings (includes alarm and motion

detection), or ALL to view all video on your system.

2. Use the buttons on the side panel to navigate the ﬁle list:

• FIRST: Jump to the ﬁrst page of the list

• PRE: Turn to the previous page

• NEXT: Turn to the next page

• LAST: Jump to the last page of the list

• ALL: Select all ﬁles

• OTHER: Reverses the selection by placing a check in the box next to the item (if not a checked)

or removes the check in the box next to the item (if item is already checked)

• BACKUP: After selecting a ﬁle(s), click to begin copying the data to a USB ﬂash drive (not included);

3. Double-click any ﬁle to begin playback.

Record/Search Menu

Record State

On-screen Playback Controls

File List Menu

Month Grid

Hour Grid

Page is loading ...

First Alert Channel/2 User manual

Brand: First Alert

Model: Channel/2

Category: Digital Video Recorders (DVR)

Type: User manual

This manual is also suitable for

Download PDF

report

First Alert Channel/2 User manual

This manual is also suitable for

First Alert Channel/2 User manual

Related papers

Other documents