Q-Logic SB-RACKKIT User manual

Q-Logic
Brand
Q-Logic
Model
SB-RACKKIT
Category
Rack accessories
Type
User manual

Q-Logic SB-RACKKIT is a rack mounting kit designed for the SANbox 5000 series of Fibre Channel switches. It allows for the installation of these switches in a standard 19-inch rack, providing a secure and organized mounting solution for data center environments.

The kit includes two rack rails and two switch rails, which are attached to the switch using 10-32 x 3/8-inch screws. The rack rails are then extended to fit the inner dimensions of the rack and fastened to the rack at both ends with two screws. Finally, the switch and rail assembly is slid into the rack rails and secured with two additional screws.

Q-Logic SB-RACKKIT is a rack mounting kit designed for the SANbox 5000 series of Fibre Channel switches. It allows for the installation of these switches in a standard 19-inch rack, providing a secure and organized mounting solution for data center environments.

The kit includes two rack rails and two switch rails, which are attached to the switch using 10-32 x 3/8-inch screws. The rack rails are then extended to fit the inner dimensions of the rack and fastened to the rack at both ends with two screws. Finally, the switch and rail assembly is slid into the rack rails and secured with two additional screws.

59109-03 A
*59109-03 A*
SANbox 5000 Series Fibre Channel Switch
Rack Mounting Guide
Rail Kit SB-RACKKIT
Tools Required
Crosshead screw driver, medium
WARNING!!
Heavier products should be placed near the bottom of a rack or cabinet. A top-heavy rack can
become unstable resulting in equipment damage or personal injury.
1. Rack rail (2)
2. Switch rail (2)
3. Screw, w/washer 10-32 x 3/8 in. (14)
4. Washer, centering
a
(8)
a For use only on racks with square holes.
L
A
L
A
L
A
L
A
L
A
L
A
L
A
L
A
0
1
2
3
4
5
6
7
L
A
L
A
L
A
L
A
L
A
L
A
L
A
L
A
1
6
L
A
1
7
L
A
1
8
L
A
1
9
L
A
3
1
2
4
3
3
5202/5602
5200/5600
5800V/5802V
SANbox 5000 Series Fibre Channel Switch Rack Mounting Guide
© 2008 QLogic Corporation. Specifications are subject to change without notice. All rights reserved worldwide. QLogic and the QLogic logo are registered trademarks of QLogic Corporation.
All other brand and product names are trademarks or registered trademarks of their respective owners. Information supplied by QLogic Corporation is believed to be accurate and reliable.
QLogic Corporation assumes no responsibility for any errors in this brochure. QLogic Corporation reserves the right, without notice, to make changes in product design or specifications.
D
D
Corporate Headquarters QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo, CA 92656 949.389.6000 www.qlogic.com
Europe Headquarters QLogic (UK) LTD. Quatro House Lyon Way, Frimley Camberley Surrey, GU16 7ER UK +44 (0) 1276 804 670
Install Switch Rails
Install the switch rails on the switch using two
screws to secure each rail. The switch can be
mounted flush or with a 1.25 inch setback
depending on how you match the holes.
1. Switch rails, flush mount
2. Switch rails, with setback
3. Screws, 10-32 x 3/8
Install Rack Rails
Extend the rack rails to fit the inner dimensions of
the rack. The rail flanges on both ends fit inside
the rack. Be sure that the inner rail is toward the
front.
NOTE:
If the rack holes are square, use a centering
washer with each screw.
Fasten the rail flanges to the rack at both ends
with two screws using the upper and lower holes.
1. Screws
2. Inner rack rail
3. Centering washer
Install the Switch
1. Slide the switch and rail assembly into the rack
rails.
2. Fasten the switch to the rack with two screws:
one through each switch rail flange.
1. Screws
2
1
1
2
3
1
3
2
1
1
  • Page 1 1
  • Page 2 2

Q-Logic SB-RACKKIT User manual

Q-Logic
Brand
Q-Logic
Model
SB-RACKKIT
Category
Rack accessories
Type
User manual

Q-Logic SB-RACKKIT is a rack mounting kit designed for the SANbox 5000 series of Fibre Channel switches. It allows for the installation of these switches in a standard 19-inch rack, providing a secure and organized mounting solution for data center environments.

The kit includes two rack rails and two switch rails, which are attached to the switch using 10-32 x 3/8-inch screws. The rack rails are then extended to fit the inner dimensions of the rack and fastened to the rack at both ends with two screws. Finally, the switch and rail assembly is slid into the rack rails and secured with two additional screws.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents