BEA EAS RF, PUSH PLATES User guide

  • Hello! I am an AI chatbot trained to assist you with the BEA EAS RF User guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1/4
12-24V
AC/DC
COM
PUL TOG
0.5s 10s
NO
NC
42.3020-V1
POWER MODE RECORD
ACTIVATION
WITH
DELAY
ACTIVATION
WITHOUT
DELAY
1
2
ON
0s
30s
4
5
1
2
8
7
6
ACTIVATION
BLUE LED
RECORD
RED LED
3
+
+
+
+
+
12-24V
AC/DC
COM
NO
NC
BN
GN
WH
YE
NO DELAY
DELAY
+
+
0s
30s
NO DELAY
NO DELAY
DELAY
DELAY
+
+
3
1
1
2
ON
1
2
ON
ON
OFF
DIP 1 DIP 2
TOGGLE
10 s
0,5 s
PULSE
1
2
ON
ON
OFF
DIP 1 DIP 2
TOGGLE
10 s
0,5 s
PULSE
2
4
5
6
7
8
EAS RF RECEIVER
DESCRIPTION AND USE
TIPS
Do not open the housing, it will be
damaged and warranty will be void.
Fasten the RECEIVER using the velcro strip.
RECORDING / DELETING
RECORDING A TRANSMITTER BUTTON FOR NON-DELAYED ACTIVATION
RECORDING A TRANSMITTER BUTTON FOR DELAYED ACTIVATION
DELETING ONE TRANSMITTER BUTTON
DELETING ALL TRANSMITTERS
RECORDING
DELETING
Record button for non-delayed activation
Delay potentiometer
Record button for delayed activation
Terminal block
Pushing the
TRANSMITTER BUTTON
once activates the output
during 0.5 or 10s.
The output is activated as
long as the
TRANSMITTER BUTTON
is pushed.
Pushing the
TRANSMITTE
R BUTTON
once activates
the output until
you push the
same button
again.
DIP-switch
BLUE activation LED
RED LED flashes after push on
TRANSMITTER BUTTON that has
not been recorded yet.
BLUE LED switches on after
push on TRANSMITTER BUTTON
that has been recorded.
RED record LED
FACTORY
VALUE: 0S
TIP
Adjust the activation delay
AFTER all transmitters have
been recorded.
All transmitters recorded in a
receiver have the same delay.
OFF
DELAY BUTTON
RED
ON
RED
FLICKERS
RED
ON
RED
FLICKERS
OFF
BLUE
ON
RED
FLASHES
RED
FLASHES
PUSH SHORTLY
SIMULTANEOUSLY
PUSH
SIMULTANEOUSLY
LONG
NO DELAY BUTTON
8sec
RED
BLUE
Antenna wire
Easy access system based
on radio frequency
BEA SA - LIEGE Science Park - Allée des Noisetiers 5 - B-4031 Angleur - T +32 4 361 65 65 - F +32 4 361 28 58 - info@bea.be - www.bea.be
2x
radio frequency
433 MHz
25 m (open field)
30 mA
12 - 24 V AC +/- 15%; 12 - 30 V DC +/- 10%
relay with switch-over contact (free of potential)
48 V AC - 60 V DC
1A (resistive)
30 W (DC) / 48VA (AC)
-10° C to 55° C
100
RED for button recording, BLUE for output activation
Technology:
Transmitter frequency:
Max. detection distance:
Power consumption:
Supply voltage of receiver:
Receiver output:
Max. voltage:
Max. current:
Max. switching power:
Temperature range:
Max. number of programmable transmitter buttons per receiver:
LEDs:
Specifications are subject to changes without prior notice
TECHNICAL SPECIFICATIONS
OFF
RED
BLUE
TROUBLESHOOTING
The receiver does
not react to the EAS
RF transmitter.
The receiver does
not react to the EAS
RF transmitter.
The door does not
react to the EAS RF
transmitter.
The receiver is not correctly wired.
Check the connection to the door
controller.
OFF
The blue LED does
not light up after
pushing the
transmitter button.
The transmitter was recorded with an
activation delay longer than desired.
The transmitter was recorded with an
activation delay.
Check the delay potentiometer
and adjust to the desired time.
Delete the transmitter from the
system and repeat the recording
procedure without delay.
The transmitter battery is down.
Check the transmitter LED and
change the battery if necessary.
It is impossible to
record a transmitter.
The maximum number of recordable
transmitters is reached.
The transmitter battery is down.
Try to reduce the number of
transmitters or connect another
receiver.
Check the transmitter LED and
change the battery if necessary.
Check the position of the antenna
on the receiver.
Check the supply voltage.
Push the transmitter 2x.
Execute the recording procedure
described on page 1 with that
transmitter.
The receiver power is off.
The transmitter has been used many
times with one receiver and then with
another one.
The transmitter is not recognized by the
receiver.
42.7022 - V2 / 10.14
EU declaration of conformity
BEA hereby declares that the product EAS RF is in conformity with the basic requirements and
the other relevant provisions of the standards 1999/5/EC and 2004/108/EC.
1/2