Premier 873X-8401 Installation guide

Category
Sanitary ware
Type
Installation guide

This manual is also suitable for

SHUT OFF WATER SUPPLY.
Verify that the hole sizes and positions of holes in the
wall are correct.
Recommended component measurements
A. Shower and / or spout outlet hole: 1-1/4" diameter.
B. Valve access hole: 6" diameter.
C. Recommended valve depth to finished wall: 2"
min. to 2-1/2"max.
Be sure that the black template plate's surface is flush
with the finished exterior surface of the wall. Be sure
to position the valve body correctly in wall. "UP"
marking up. The 8" Minimum from the valve body to
the tub spout is required for proper operation.
Brand Tub & Shower Faucets
6.
3.
2A.
4.
1.
INSTALLATION STEPS: Single handle tub & shower faucet
Cleaning:
To maintain and protect the fine luster of all products, clean with a soft, damp cloth
only. DO NOT USE detergents or cleansers as they may harm the protective finish.
Plumber's putty
Basin wrench
Pipe tape
Screwdriver
Pipe wrench
Groove joint pliers
Adjustable wrench
Tools:
INSTALLATION
FOR TUB SPOUT INSTALLATION
Install tub spout. Place spout onto quick connection
until the spout becomes flush with the finished wall
and tighten screw (1) with Allen wrench (Hex:
3.97mm).
7.
5.
8.
9.
Before installing escutcheon, remove the plastic cap
from plaster guard by twisting cap in a clockwise
direction. Remove the screw from the inverter.
Place handle on valve stem and turn handle to full
on mixed position. Turn on hot and cold water lines
to full open for one minute each. Check for leak.
Shut off water at faucet. Remove the handle.
ADJUSTING WATER TEMPERATURE
Turn on water so that cold water is as cold as it will get and
hot water is as hot as it will get. Remove the Rotational Limit
Stop from the valve by sliding it off the stem. Place handle
back on stem and rotate fully counterclockwise to the hottest
position. Place a thermometer in a plastic tumbler and hold in
the water stream. If the water temperature is above 120° F,
the Rotational Limit Stop must be rotated counterclockwise to
decrease temperature. Reinstall the stop by sliding it back on
to the stem before reinstalling the handle.
MAKE SURE COLD WATER FLOWS FROM THE VALVE
FIRST.
MAKE SURE WATER (AT THE HOTTEST FLOW) DOES
NOT EXCEED THE TEMPERATURE LIMIT ALLOWED BY
YOUR PLUMBING CODES (120° F OR 110° F).
Install escutcheon (1) onto valve and then insert
screws (2) to attach to valve body. Place handle
assembly (3) onto the valve and secure with screw
(4). Insert index (5) into handle. Attach shower head
(6) to shower arm.
Model Number: 119273 & 119274 & 119275 &
119276 & 119277 & 119278
SUPPLY CONNECTION LAYOUT
For Tub and Shower Combinations:
Wrap plumber's tape around pipe threads in a
clockwise direction. Connect water supplies to left
(hot) and right (cold) valve body inlets. Connect
shower outlet pipe (2) and tub outlet pipe (3) to
valve body. Connect Pipe Elbow (1) (not included)
to the end of the pipe.
FOR SHOWER ARM INSTALLATION.
Insert the long end of the shower arm (2) through the
flange (1) then wrap plumber's tape to both sides of
shower arm. Screw long end of the shower arm into
pipe elbow inside the wall.
FLUSHING
For Tub and Shower Combinations:
Turn on Hot and Cold water supply lines allowing
water to flow from tub spout outlet (2) until all
foreign matter has cleared the line.
For Shower Only Combinations:
Turn on Hot and Cold water supply lines allowing
water to flow from shower outlet (1) until all
foreign matter has cleared the line. Pressure
must be approximately equal on both Hot and
Cold sides for valve to function properly.
Tub&Shower
1 1/4" Dia
Shower Only
8" Min.
30"
48"
30"
6" Dia
Shower Only
48"
Tub&Shower
1 1/4" Dia
rotational limit stop
hotter
stop on cartridge
colder
1
2
3
1
2
1
2
6
1
2
3
4
5
SUPPLY CONNECTION LAYOUT
For Shower Only Combinations:
Wrap plumber's tape around pipe threads in a
clockwise direction. Connect water supplies to left
(hot) and right (cold) valve body inlets. Connect
shower outlet pipe (2) to valve body. Plug bottom
outlet (3) with Pipe Cap or Plug (4). Connect Pipe
Elbow (1) (not included) to the end of the pipe.
3
4
1
2
2B.
www.premierfaucet.com, [email protected]
Allen wrench
1
Parts List
119273 & 119274 & 119275 & 119276 & 119277 & 119278
1
1
1
1
1
10
13
12
11
101003
373
8
109-8
Plug
9
O-Ring
Sleeve
6
282
283
QTY.
1
1
1
1
1
370 1
Handle Screw & Screw Cap
Escutcheon 5
4
372
994442
2
3
PART DESCRIPTION
MODEL NO.119273
NO. PART NO.
Screw
7
Temp Limit Stop
994693
1
Spout
Shower Flange
Shower Arm
374
1
1
Shower Head
375
1
2
1
3
4
5
6
7
8
11
12
13
14
15
Handle Assembly
371
Inverter
68
9
Ceramic Cartridge With Stop
994695
14
1 1
10
Integral Stop
994722
15
1
994693
Temp Limit Stop
8
1
Ceramic Cartridge With Stop
Shower Arm
14
15
Shower Head
Integral Stop
10
Plug
Shower Flange
Spout
11
13
12
9
994616
1 1
1
380
994722
994414
994307
109-8
1
1
1 1
1
1
994695
PART DESCRIPTION
MODEL NO.119274
Handle Screw & Screw Cap
Handle Assembly
2
Screw
4
Escutcheon 5
O-Ring
7
6
Sleeve
3
Inverter
1
NO.
1377
1
994443
1
378
1
282
1
297
168
1376
QTY.PART NO.
994693
Temp Limit Stop
8
1
Ceramic Cartridge With Stop
Shower Arm
14
15
Shower Head
Integral Stop
10
Plug
Shower Flange
Spout
11
13
12
9
350
1 1
1
385
994722
348
352
109-8
1
1
1 1
1
1
994695
PART DESCRIPTION
MODEL NO.119275
Handle Screw & Screw Cap
Handle Assembly
2
Screw
4
Escutcheon 5
O-Ring
7
6
Sleeve
3
Inverter
1
NO.
1382
1
349
1
383
1
282
1
384
168
1381
QTY.PART NO.
Handle Screw & Screw Cap
MODEL NO.119277
Ceramic Cartridge With Stop
5 Escutcheon
372 5 Escutcheon
1
10
994722
10
1
Shower Arm
14
15
Shower Head
11
13
Shower Flange
Plug
13
Shower Arm
1 1
374
1
375
Shower Head
14
11
1
1
1
109-8
373
Shower Flange
Plug
Temp Limit Stop
8
9
Integral Stop
Ceramic Cartridge With Stop
7
6
Sleeve
O-Ring
8
Temp Limit Stop
1
994693
994695
1
9
Integral Stop
283
282
1
1
Sleeve
6
7
O-Ring
NO. PART DESCRIPTION
PART NO.NO. PART DESCRIPTION QTY.
3
4
Inverter
Screw
2
1
Handle Assembly
Handle Screw & Screw Cap
68
994442
1
1
Inverter
3
4
Screw
371
370 1
1
1
2
Handle Assembly
MODEL NO.119276
383
1
5 Escutcheon378
1
1
994722
10
1
994722
14
Shower Arm
1 1
994616
380
1
Shower Head
15
1 1
1
109-8
994414
13
11
Shower Flange
Plug
1 1
350
385
1
1 1
1
109-8
348
Ceramic Cartridge With Stop
8
Temp Limit Stop
1
994693
994695
1
9
Integral Stop
297
1
282
1
Sleeve
6
7
O-Ring
1
994693
994695
1
384
1
282
1
PART NO. QTY.NO. PART DESCRIPTIONPART NO. QTY.
Handle Screw & Screw Cap
68 1
994443
1
Inverter
3
4
Screw
376 1
377 1
1
2
Handle Assembly
68 1
349
1
381 1
382 1
MODEL NO.119278
15
  • Page 1 1
  • Page 2 2

Premier 873X-8401 Installation guide

Category
Sanitary ware
Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI