Agri-Fab LBD48 User guide

Brand: Agri-Fab

Model: LBD48

Type: User guide

PRINTED IN U.S.A.

FORM NO. 41860 (03/23/18)

• Safety

• Assembly

• Operation

• Maintenance

• Parts

Model No.

Modelo No.

Modèle n

LBD48E

OWNER'S MANUAL

MANUAL DE USUARIO

NOTICE D’UTILISATION

CAUTION:

ReadRulesfor

SafeOperation

andInstructions

Carefully

PRECAUCIÓN:

LeaCuidadosamentelas

ReglaseInstrucciones

deSeguridad

ATTENTION:

Lireetsuivreattentivement

lesinstructionset

consignesdesécurité

decettenotice.

the fastest way to purchase parts

www.speedepart.com

48" SNOW BLADE

CUCHILLA QUITANIEVE DE 48" (122 CM)

LAME CHASSE-NEIGE DE 48 PO. (122 CM)

• Seguridad

• Armado

• Operación

• Mantenimiento

• Piezas

• Sécurité

• Assemblage

• Utilisation

• Entretien

• PiècesdeRechange

TABLE OF CONTENTS

SERVICEANDADJUSTMENTS .................................. 13

STORAGE .................................................................... 13

TROUBLESHOOTING .................................................. 13

REPAIRPARTSILLUSTRATION ................................. 30

REPAIRPARTSLIST .................................................... 31

PARTSORDERING/SERVICE .................. BACKCOVER

Lookforthissymboltopointoutimportantsafetyprecautions.Itmeans—Attention!! Become

alert!! Your safety is involved.

RULES FOR SAFE OPERATION

SAFETYRULES ............................................................. 2

CARTONCONTENTS .................................................... 2

FULLSIZEHARDWARECHART ................................... 3

ASSEMBLY ..................................................................... 4

OPERATION ..................................................................11

MAINTENANCE ........................................................... 12

1. Readthetractorandsnowbladeowner'smanuals

andknowhowtooperateyourtractorbeforeusing

tractorwithsnowbladeattachment.

2. Neveroperatetractorandsnowbladewithout

wearingproperclothingsuitedtoweatherconditions

andoperationofcontrols.

3. Neverallowchildrentooperatetractorandsnow

blade,anddonotallowadultstooperatewithout

properinstructions.

4. Alwaysbeginwithtransmissioninrst(low)gearand

graduallyincreasespeedasrequired.

Anypowerequipmentcancauseinjuryifoperatedimproperlyoriftheuserdoesnotunderstandhowtooperatetheequipment.

Exercisecautionatalltimes,whenusingpowerequipment.

CARTON CONTENTS

ENGLISH

REF QTY PART NO. DESCRIPTION

1 1 25122 LongHangerBracket

2 1 25121 ShortHangerBracket

3 1 25125 RearMountingBracket

4 1 24023 PivotSupportBracket

5 1 64732 ThrustChannel

6 1 — ChannelAssembly

7 1 — BladeAssembly

8 1 48167 BladePivotRod

9 1 65519 LiftHandleTube

10 1 63033 LiftHandleRod

REF QTY PART NO. DESCRIPTION

11 2 24659 RearSupportChannel

12 1 49808 Cable

13 1 HA23380 RearLocatingBracket

14 1 — GripAssembly

15 1 R9466R BladeAdjustSpring

16 2 23151 AngleLockBars

17 2 25124 FrameBracket

18 2 24690 SkidShoe

19 1 46066 BladePivotShaft

SHOWN FULL SIZE

HARDWARE PACKAGE

NOT SHOWN FULL SIZE

ENGLISH

REF QTY PART NO. DESCRIPTION

A 1 46071 HexBolt,1/4-20x3-1/4"

B 1 1509-90 HexBolt,1/4-20x1-1/4"

C 4 43063 HexBolt,5/16-18x1"

D 1 43085 HexBolt,5/16-18x1-1/2"

E 4 710-0305 CarriageBolt,3/8-16x1-1/4"

F 18 43350 CarriageBolt,3/8-16x1"

G 3 47189 NylockNut,1/4-20

H 11 47810 NylockNut,5/16-18

I 16 HA21362 NylockNut,3/8-16

J 2 712-0256 HexJamNut,5/16-24

K 1 HA3980 ClevisPin,5/8"x1-3/4"

L 2 44062 ClevisPin,1/2"x1"

M 3 43343 HairpinCotter,Large

N 4 43055 HairpinCotter,Small

O 2 43010 CotterPin,1/8"x1-1/4"

P 2 44917 Palnut,3/8"

Q 8 43001 HexBolt,3/8-16x1"

R 2 43003 LockWasher,3/8"

REF QTY PART NO. DESCRIPTION

S 3 R19171616 Washer,1/2"x1"

T 1 23658 Spacer,9/16"x5/8"

U 2 46053 Spacer,9/16"x1"

V 2 44326 CarriageBolt,5/16-18x1"

W 2 43080 CarriageBolt,5/16-18x3/4"

X 2 47630 HexBolt,5/16-18x3/4"SelfThd.

Y 2 43070 Washer,3/8"

Z 2 43087 HexBolt,3/8x1-1/4"

AA 4 47572 FlangedLockNut,3/8-16

BB 6 43081 Washer,5/16"

CC 4 R19172410 Washer,1/2"x1-1/2"

DD 2 746-0260 CableEndFitting

EE 1 05762 CableMountBracket

FF 1 43348 AngleLockSpring

GG 2 726-0178 NylonTie

HH 1 23856 SpringMountRod

II 1 46065 ChannelPivotPin

A B

(1) Pliers

(1) Hammer

(1) AdjustableWrench(orsocketset)

(1) 9/16"OpenEndorBoxEndWrench

(2) 7/16"OpenEndorBoxEndWrench

(2) 1/2"OpenEndorBoxEndWrench

TOOLS REQUIRED FOR ASSEMBLY

REMOVAL OF PARTS FROM CARTON

• Removetheloosepartsandthehardwarepackages

fromthecarton.Layoutallpartsandhardwareand

identifyusingtheillustrationsonpages2and3.

IMPORTANT: Youwillnotneedallofthepartssupplied

withyourblade.Disposeofunusedpartsafteryouhave

nishedassemblingtheblade.

NOTE: Righthand(R.H.)andlefthand(L.H.)are

determinedfromtheoperatorspositionwhileseatedon

thetractor.

ENGLISH

CAUTION: Do notbeginassemblinguntil

thetractorengine,mufflerandexhaust

deectorhavebeenallowedtocooloff.

TRACTOR PREPARATION

• Allowengine,mufflerandexhaustdeectortocool

beforebeginning.

• Removethehoodfromthetractorforbetteraccess.

• Removethemowerdeckfromthetractor.Refertothe

instructionsinyourtractorowner'smanual.

• Removeanyfrontmountedattachmentsuchasa

bumper.Saveallpartsforre-installation.

• Removeanywiringfromtheareaofthetractorframe

wheretheframebracketswillbeattached.Reinstall

thewiringwiththeprovidedplastictie.

• Ifnecessary,temporarilyremovethebrowningshield

fromthefrontofthetractorforbetteraccess.

USE THE INSTRUCTIONS IN STEP 1 IF YOUR

TRACTOR HAS A SINGLE FRONT BRACKET

FOR ATTACHING THE MOWER DECK

STEP 1: (SEE FIGURE 1)

Refertopage6forexamplesofhowtoattachtheFrame

Bracketstosomeothertractormodels.

• Holdtheframebracketsothatthetwoholesareat

thebottomandplaceitagainstthesideofthetractor

frameinfrontofthefrontaxle.Aligntwoupperholes

inthebracketwithtwoholesinthetractorframe.Turn

thebracketoverifnecessary.Attachthebracketusing

theappropriatehardware.

FIGURE 1B

FIGURE 1A

3/8" x 1" HEX BOLT (Q)

FRAME BRACKET

3/8" NYLOCK

NUT (I)

3/8" x 1"

CARRIAGE BOLT (F)

3/8" LOCK WASHER (R)

SEARS 917 SERIES TRACTOR FRAME

JOHN DEERE LT TRACTOR FRAME

FRAME

BRACKETS

5/16" x 1"

HEX BOLTS (C)

5/16" NYLOCK

NUTS (H)

ASSEMBLY

SKIP TO STEP 3 IF YOUR TRACTOR HAS

TWO FRONT BRACKETS FOR ATTACHING

THE MOWER DECK.

JOHN DEERE LT TRACTOR

FIGURE 2

STEP 2: (SEE FIGURE 2)

• MeasurethedistancesL,HandW.

L= distancefromcenteroflowerholesinframe 

 brackettofrontoftractorframe.

H= distancetocenterofholeinframebracketthatis

 closesttobeing6"abovegroundlevel.

W=distancebetweentheinsideoftheframe 

 brackets.

• Proceedtostep4.

FIGURE 3 - SEARS TRACTOR SHOWN

SEARS (LT) TRACTOR FRAME

DECK SUSPENSION

BRACKET

STEP 3: (SEE FIGURE 3)

• MeasurethedistancesL,HandW.

L= distancefromcenterofholeindecksuspension

 brackettofrontoftractorframe.

H= distancefromcenterofholeindecksuspension

 brackettogroundlevel.

W=insidedistancebetweenthedecksuspension 

 brackets.

USE THESE INSTRUCTIONS IF YOUR

TRACTOR HAS TWO FRONT BRACKETS

FOR ATTACHING THE MOWER DECK

ATTENTION:Gobacktostep1ifyourtractorhasonly

onefrontbracketforattachingthemowerdeck.

3/8" x 1-1/4"

HEX BOLT (Z) &

3/8” WASHER (Y)

3/8" NYLOCK NUT (I)

LONG HANGER BRACKETS

Ends down when "H" is 6" or less

Ends up when "H" is more than 6"

L+

FRONT PLATE

FIGURE 4

STEP 4: (SEE FIGURE 4)

Refertopage6forexamplesofhowtoattachtheHanger

Bracketstosomeothertractormodels.

• SelectthepairofslotsinthetopoftheThrust

Channelthatwillprovideenoughclearancebetween

thebladeandthefrontofthetractorwhileminimizing

overhang.

Selectthepairofslotsbasedondistance"L"

measuredinstep2orstep3.

L=5"orless Attachtothefrontpairofslots.

L=5"to7" Attachtothemiddlepairofslots.

L=7"to9" Attachtotherearpairofslots.

• ArrangetheHangerBracketswiththeshortHanger

BracketontheinsideofthelongHangerBracketand

placethemontopoftheThrustChannel.Ifdistance

"H",measuredinstep2or3,islessthan6",point

thebracketsdown.Ifdistance"H"ismorethan6",

pointthebracketsup.

• AdjustthewidthoftheHangerBracketstojustslightly

lessthandistance"W"measuredinstep2or3.

CenterthebracketsontheThrustChannelandattach

themusingtwo3/8"x1-1/4"hexbolts,3/8"washers,

and3/8"nylocknuts.

• Tighten the nuts andthenmakesurethehanger

bracketstbetweenthedecksuspensionbrackets

orframebracketsonthetractor.

• Proceedtostep5onpage7.

USE THESE INSTRUCTIONS FOR ALL

TRACTORS

12.75"

3/8" x 1"

HEX BOLT

3/8" x 1"

CARRIAGE

BOLT

LOCATE HANGER BRACKETS IN

MIDDLE SET OF SLOTS IN THRUST CHANNEL

FRAME

BRACKET

SEARS 917 SERIES & HUSQVARNA TRACTORS WITH

CENTER DECK SUSPENSION BRACKET AND 16" TIRES

SEARS 917 SERIES & HUSQVARNA LAWN TRACTORS

TRACTOR

SUSPENSION

BRACKET

LOCATE HANGER BRACKETS IN

MIDDLE SET OF SLOTS IN THRUST CHANNEL

9.75"

TRACTOR

SUSPENSION

BRACKET

12"

13.00"

3/8" x 1"

HEX BOLT

5/16" x 1"

HEX BOLT

LOCATE HANGER BRACKETS IN

MIDDLE SET OF SLOTS IN THRUST CHANNEL

FRAME

BRACKET

SEARS 247 SERIES LT 2000 &

TROY-BILT PONY TRACTORS

FRAME

BRACKET

LOCATE HANGER BRACKETS IN FRONT

SET OF SLOTS IN THRUST CHANNEL

5/16" x 3/4"

HEX BOLT

(self threading)

3/8" x 1"

HEX BOLT

13"

SEARS MODEL 247.2898 PROFESSIONAL SERIES

& MTD YARD TRACTORS & GARDEN TRACTORS

1/2" WASHER

(LARGE)

12.75"

FRAME

BRACKET

3/8" x 1"

CARRIAGE

BOLT

5/16" x 3/4"

HEX BOLT

(self threading)

1/2" WASHER

(LARGE)

LOCATE HANGER BRACKETS IN

MIDDLE SET OF SLOTS IN THRUST CHANNEL

SEARS 917 SERIES & HUSQVARNA TRACTORS WITH

CENTER DECK SUSPENSION BRACKET AND 15" TIRES

13.00"

5/16" x 1"

HEX BOLT

LOCATE HANGER BRACKETS IN

MIDDLE SET OF SLOTS IN THRUST CHANNEL

FRAME

BRACKET

SEARS NX-15 FRAME TRACTORS

FRAME

BRACKET

LOCATE HANGER BRACKETS IN FRONT

SET OF SLOTS IN THRUST CHANNEL

5/16" x 3/4"

HEX BOLT

(self threading)

5/16" x 1"

HEX BOLT

13.5"

SEARS 6” TURNING RADIUS TRACTORS

CUB CADET ENDURO TRACTORS

3/8" x 1"

BOLT

1/2" WASHER

(LARGE)

FRAME

BRACKET

LOCATE HANGER BRACKETS IN FRONT

SET OF SLOTS IN THRUST CHANNEL

13"

SEARS 917 SERIES & HUSQVARNA GARDEN TRACTORS

LOCATE HANGER BRACKETS

IN MIDDLE SET OF SLOTS IN

THRUST CHANNEL

JOHN DEERE LT

13"

FRAME

BRACKET

5/16" x 1"

HEX BOLT

MTD - GARDEN TRACTORS

13"

TRACTOR

SUSPENSION

BRACKET

LOCATE HANGER BRACKETS IN FRONT

SET OF SLOTS IN THRUST CHANNEL

MTD GARDEN TRACTORS

13"

TRACTOR

SUSPENSION

BRACKET

LOCATE HANGER BRACKETS IN FRONT

SET OF SLOTS IN THRUST CHANNEL

MTD - LAWN TRACTORS

13"

TRACTOR

SUSPENSION

BRACKET

LOCATE HANGER BRACKETS IN FRONT

SET OF SLOTS IN THRUST CHANNEL

MTD LAWN TRACTORS

13"

FRAME

BRACKET

LOCATE HANGER BRACKETS IN FRONT

SET OF SLOTS IN THRUST CHANNEL

5/16" x 1"

HEX BOLT

JOHN DEERE D100 SERIES TRACTORS

13"

FRAME

BRACKET

LOCATE HANGER BRACKETS IN FRONT

SET OF SLOTS IN THRUST CHANNEL

5/16" x 1"

HEX BOLT

CUB CADET ENDURO TRACTORS

3/8" x 1"

HEX BOLT

1/2" WASHER

(LARGE)

FRAME

BRACKET

LOCATE HANGER BRACKETS IN FRONT

SET OF SLOTS IN THRUST CHANNEL

13"

LOCATE HANGER BRACKETS IN FRONT

SET OF SLOTS IN THRUST CHANNEL

STEP 9: (SEE FIGURE 9)

• Assemblethepivotsupportbrackettothefrontof

theThrustChannelusingfour3/8"x1"hexboltsand

four3/8"angedlocknuts.Makesurethebracketis

straightandthentighten.

FIGURE 7

FIGURE 9

FIGURE 8

FIGURE 5

FIGURE 6

ENGLISH

STEP 5: (SEE FIGURE 5)

• AttachtheRearLocatingBrackettothetopofthe

RearMountingBracketusingtwo3/8"x1"Carriage

boltsand3/8"nylocknuts.Tightennuts.

• AttachtheRearSupportChannelstothemiddleset

ofholesinthesidesoftheRearMountingBracket

usingfour3/8"x1"CarriageBoltsand3/8"nylock

nuts.Finger tighten only.

REAR SUPPORT

CHANNELS

REAR MOUNTING

BRACKET

REAR LOCATING

BRACKET

3/8" x 1"

CARRIAGE BOLT (F)

3/8" NYLOCK NUT (I)

STEP 6: (SEE FIGURE 6)

• SlidetheRearSupportChannelsundertherearof

thetractor.AttachtheRearMountingBrackettothe

TractorDrawbarusingthe5/8"x1-3/4"ClevisPinand

alargeHairpinCotter.

5/8" x 1-3/4"

CLEVIS PIN (K)

LARGE

HAIRPIN

COTTER (M)

REAR

MOUNTING

BRACKET

REAR LOCATING

BRACKET

REAR SUPPORT

CHANNEL

STEP 7: (SEE FIGURE 7)

• SlidetheThrustChannelunderthefrontofthetractor.

AttachtheHangerBracketstotheFrameBracketsor

DeckSuspensionBracketsusingtwo1/2"x1"clevis

pins,1/2"washersandlargehairpincotters.

STEP 8: (SEE FIGURE 8)

• PlacetheThrustChannelbetweenthetwoRear

SupportChannels.Installfour3/8"x1"carriagebolts

and3/8"nylocknutsusingthemostwidelyspaced

holesthatalignwithslots.Finger tighten only.

• IftheRearSupportChannelsbumpagainstthe

bottomofthetractor,reattachtherearofthechannels

toalowersetofholesintheRearMountingBracket.

Ifthereismoreclearancethannecessarybetween

theRearSupportChannelsandthebottomofthe

tractor,reattachtherearofthechannelstoahigher

setofholesintheRearMountingBracket.

• Tightenallboltsandnutsinstalleduptothispoint.

• MeasuretheheightofthefrontplateontheThrust

Channel.Ifitisnot4"to5"abovetheground,reinstall

theclevispinsintheHangerBracketstoahigheror

lowerholepositiontoattainthecorrectheight.

THRUST

CHANNEL

1" x 1/2" CLEVIS

PIN (L)

LARGE HAIRPIN

COTTER (M)

1/2" WASHER (S)

REAR

SUPPORT

CHANNELS

FRONT

PLATE

3/8" x 1"

CARRIAGE BOLT (F)

3/8" NYLOCK

NUT (I)

4" to 5"

GROUND

3/8" x 1"

HEX BOLT (Q)

3/8" FLANGED

LOCK NUT (AA)

(Top View)FIGURE 11

FIGURE 12 (Right Hand Side View)

FIGURE 13 (Left Hand Side View)

(Right Hand Side View)FIGURE 10

ENGLISH

STEP 10: (SEE FIGURE 10)

• Placethetwoanglelockbarstogethersothatallholes

arealigned.Assemblea3/8"x1-1/4"carriageboltand

a3/8"nylocknutinthetophole.Besuretoinsertthe

boltfromthesideindicated. Finger tighten only.

• Inserttheroundhookendoftheanglelockspringup

throughtheholeinbracket(a).

• Holdtheanglelockbarssothatthesquareholesare

atthetop.Insertthestraighthookendoftheanglelock

springthroughthemiddleholeinbothanglelockbars.

• Inserttheanglelockbarsdownthroughtheslotin

thechannel.Underneaththechannel,placea1"long

spaceroneachsideoftheanglelockbarsandinsert

a1/4"x3-1/4"boltthroughthechannel,theangle

lockbarsandthespacers.Securetheboltwitha1/4"

nylocknut.Tightensothatlockbarscanpivotfreely.

• Atthistimetightenthe3/8"carriageboltandnylon

locknutpreviouslyassembledtoanglelockbars.

NOTE: Whentheanglelockbarsarepulledback,the

pivotplateshouldunlockandbefreetopivot.

STEP 11: (SEE FIGURE 11)

• Useahammertotapa3/8"palnutontooneendofthe

springmountrod.Inserttherodthroughtherearsetof

holesinthepivotplate.Supporttheassembledendof

thespringmountrodonablockofwood,andtapthe

remaining3/8"palnutontotheotherendoftherod.

STEP 12: (SEE FIGURE 12)

• Assemblea3/8"x1-1/4"carriageboltthroughthesquare

holeinthecablemountbracketandthroughthesquare

holeintheanglelockbarsasshown.(Thecarriagebolts

shouldfaceinoppositedirections.)Usingpliersholdthe

cablemountbracketinposition,anglingdowntowards

theL.H.holeinthechannelasshown.Securewitha3/8"

nylocknut. Tighten.Referalsotogure14forthecorrect

angleforthecablemountbracket.

STEP 13: (SEE FIGURE 13)

• Selecttheendofthecontrolcablethathasnorubber

cap.Assembleone5/16"jamnutapproximately3/4"

ontothethreadedendofthecontrolcable.Assemble

thethreadedcableendthroughtheroundholein

thecablemountbracketasshownandsecurewith

another5/16"jamnut.Tighten.

NOTE: Someadjustmentofjamnutsmayberequired

afterbladeassemblyiscompleted.

1/4" x 3-1/4"

HEX BOLT (A)

1" SPACERS (U)

1/4" NYLOCK

NUT (G)

ANGLE

LOCK

SPRING (EE)

(a)

3/8"x 1-1/4"

CARRIAGE BOLT (E)

CHANNEL

ANGLE

LOCK BARS

3/8" NYLOCK

NUT (I)

3/8" PALNUT (P)

PIVOT

PLATE

SPRING

MOUNT

ROD (HH)

3/8" PALNUT (P)

3/8" x 1-1/4"

CARRIAGE BOLT (E)

3/8" NYLOCK

NUT (I)

ALIGN CABLE

MOUNT BRACKET (DD)

WITH L.H. HOLE

ANGLE

LOCK

BARS

FRONT

CHANNEL ASSEMBLY

5/16" JAM NUT (J)

CABLE MOUNT

BRACKET

REAR

3/4"

FIGURE 16 (Right Hand Side View)

FIGURE 14 (Left Hand Side View)

(Right Hand Side View) FIGURE 15

ENGLISH

STEP 14: (SEE FIGURE 14)

• Assembleballendofcontrolcableupthroughholein

cableendttingandpulluntilballslipsinsidecurled

edgeofttingasshown.Ifballwon'tslipunderedge

ofcurlitwillneedtobeinsertedthroughopenendof

curl.

• Assemblea1/4"x1-1/4"hexboltdownthroughthe

cableendtting,the5/8"longspacerandtheleft

handholeinthechannelassembly.Securewitha

1/4"nylocknut. Tighten.

NOTE: Makesurethecablemountbracketisalignedwith

thecableendttingasshowntopreventbindingofcable.

Attachtheotherendofthecontrolcableinalaterstep.

STEP 15: (SEE FIGURE 15)

• Toattachthebladetothechannelassembly,align

thenotchedholesinthepivotplatewiththenotched

holesintheblade.Inserta1/8"x1-1/4"cotterpin

downthroughtheholeatthebendinthebladepivot

shaft.Spreadtheendsofthepin.Fromtheleftside

insertthebladepivotshaft,bendfacingup,through

thenotchedholes.Securetheshaftwithanother1/8"

x1-1/4"cotterpinthroughtheendholeintheshaft.

Spreadtheendsofthepin.

• Removetheplasticcapandone3/8"hexnutfromthe

boltinthebladeadjustspring.Adjusttheremaining

3/8"hexnutdownapproximately1"ontothebolt

threads.Hookthespringoverthespringmountrod

asshown.Placetheboltupthroughtheholeinthe

topedgeofthebladeandreassembletheother3/8"

hexnutandtightendownagainstthetopedgeofthe

blade.Replacetheplasticcapovertheendofthebolt

threads.

STEP 16: (SEE FIGURE 16)

• Assemblethe1/2"washerontothechannelpivotpin.

• Attachthechannelassemblytothetractorbyplacing

theendofthechannelassemblyupinsidethe

pivotsupportbracketonthetractor.Alignthehole

inthepivotsupportbracketwiththesecond hole

inthechannelassembly.Insertthechannelpivot

pinthroughthealignedholesfromtheleftsideand

securewithasmallhairpincotterpushedalltheway

throughtotheloopend.

NOTE: Allhairpincottersonthissnowbladeshouldbe 

pushedthroughtotheirloopend.

1/4" x 1-1/4"

HEX BOLT (B)

CABLE END

FITTING

1/4" NYLOCK NUT (G)

5/8" SPACER (T)

CHANNEL

ASSEMBLY

HOLE

REAR

3/8" HEX NUT

(TOP)

PLASTIC

CAP

3/8" HEX NUT

(BOTTOM)

BLADE

1/8" x 1-1/4"

COTTER PIN (O)

BLADE

PIVOT

SHAFT

SPRING

MOUNT

ROD (HH)

BLADE

ADJUST

SPRING

1/8" x 1-1/4"

COTTER

PIN (O)

PIVOT PLATE

1/2" WASHER (S)

CHANNEL

PIVOT PIN (II)

CHANNEL

ASSEMBLY

HOLE IN END OF

CHANNEL ASSEMBLY

SMALL HAIRPIN

COTTER (N)

PIVOT SUPPORT

BRACKET

ENGLISH

STEP 17: (SEE FIGURE 17)

• Fromtheleftside,inserttheweldedendofthelift

handlerodthroughtheexposedholesintheendofthe

channelassembly.Next,inserttheliftlinkpinthrough

theholeinthebracketthatisweldedtothelifthandle

rod.(Theliftlinkispre-assembledtothepivotsupport

bracket).Securethebracketwithasmallhairpincotter.

• Applyalightcoatingofoiltothestraightupperportion

ofthelifthandlerod.Slidethelifthandletubeontothe

rod.

LIFT HANDLE ROD

HAIRPIN COTTER (N)

LONG PIN

(LIFT LINK)

WELDED BRACKET

LIFT HANDLE TUBE

5/16" x 1"

CARRIAGE BOLT (V)

5/16" x 3/4"

CARRIAGE BOLT (W)

5/16" WASHER (BB)

5/16" NYLOCK NUT (H)

SKID SHOE

STEP 18: (SEE FIGURE 18)

• Pivotthebladetothecenterpositionandloweritto

theground.Placeshimsunderthebladetocreate

theamountofgroundclearanceyouwant.Themore

uneventhesurfacethemoreclearanceyouwillneed.

• Attachtheskidshoestothebladeusinga5/16"x3/4"

carriageboltinthetopholeanda5/16"x1"carriage

boltinthebottomhole.Withtheskidshoesrestingon

theground,securetheboltswith5/16"washersand

5/16"nylocknuts.

FIGURE 18 (Left Hand Side View)

FIGURE 19 (Right Hand Side View)

FIGURE 20 (Right Hand Side View)

CABLE END

FITTING (DD)

STEP 19: (SEE FIGURE 19)

• Removetherubbercapandtherstjamnutfromthe

threadedendofthecontrolcableandslidethemonto

thecontrolcablewire.Adjustthesecondjamnuton

thethreadssothatitisapproximately3/4"fromend.

Assemblethreadedendofcablethroughthecable

mountbracketonthelifthandletubeandsecureit

withtherstjamnut.Reinstalltherubbercapontothe

threadedcableend.

NOTE: Someadjustmentofjamnutsmayberequired 

afterbladeassemblyiscompleted.

STEP 20: (SEE FIGURE 20)

• Assembletheplasticgripontothegripassembly.

• Attachthegripassemblytothelifthandletubeusing

one5/16"x1-1/2"hexboltandone5/16"nylocknut.

Donotovertightenthenylocknut.Thegripassembly

mustpivotfreely.

• Assembletheballendofthecabletoacableend

ttingaswasdonetotheotherendofthecable.

Securethecableendttingtotheweldboltonthelock

releasegripwitha1/4"nylocknut.Donotovertighten

thenylocknut.Thecablettingmustpivotfreely.

RUBBER

CAP

CABLE MOUNT BRACKET

JAM NUTS

3/4"

CONTROL CABLE END

5/16" x 1-1/2"

HEX BOLT (D)

PLASTIC

GRIP

1/4" WELD

BOLT

CABLE END

FITTING (DD)

5/16" NYLOCK

NUT (H)

1/4 " NYLOCK

NUT (G)

CABLE

GRIP

ASSEMBLY

FIGURE 17 (Left Hand Side View)

FIGURE 21 (Left Hand Side View)

ENGLISH

STEP 21: (SEE FIGURE 21)

• Placethelongendofthebladepivotroddown

throughthebladepivotshaft.Attachtheshortendof

thebladepivotrodtothelifthandletube.Secureboth

endswithsmallhairpincotters.

• Usethetwoplastictiestoholdthecablesecurely

totheoutsideofthehandletubeandawayfromthe

tractortoavoiddirectheatfromthetractormuffler.

BLADE

PIVOT

ROD

LIFT HANDLE

TUBE

SMALL HAIRPIN

COTTER (N)

SMALL HAIRPIN COTTER (N)

PLASTIC TIES (GG)

BLADE PIVOT SHAFT

FIGURE 22

FIGURE 23

To Raise or Lower the Snow Blade

• Usethehandlegriplocatedontheendofthehandle

tube.Toraisetheblade,pullbackwhilepushingdown

onthehandlegrip. Tolowerblade,pullbackwhile

liftinguponhandlegrip.Seegure22.

OPERATION

HOW TO USE YOUR SNOW BLADE

To Pivot the Blade

• Raisethebladetotransportposition.Tounlockthe

blade,pushthegripassemblydownagainstthehandle

tube.Topivottheblade,keepthegripdepressedand

pushforwardorpullbackonthehandletube,sliding

italongtheliftrod.Releasethegriptolocktheblade

whenitisineithertherighthand,thelefthandorthe

straightaheadposition.Seegure23.

KNOW YOUR SNOW BLADE

Read this owner's manual and safety rules before operating your snow blade.

Comparetheillustrationbelowwithyoursnowbladetofamiliarizeyourselfwiththevariouscontrolsandtheirlocations.

LOCKRELEASEGRIPASS'Y. Unlocksthebladetoswiveltotherightandleft.

LIFTHANDLETUBE Raisesorlowersthebladeandpivotsbladetotherightandleft.

BLADEPIVOTROD Connectsbladetohandletube.Pivotsbladetotherightandleft.

ANGLELOCKBARS Locksthebladeineithertherighthand,lefthandorstraightaheadposition.

BLADEADJUSTSPRING Holdsbladeinpositionbutpermitsittopivotforwardtopassoveranobstruction.

BLADESHOE Ground-contactingpartofblade.Adjustsforadequategroundclearanceofblade.

BLADEPIVOTSHAFT Connectsbladetochannelassembly.Allowsbladetopivotforward.

LIFTHANDLEROD Connectslifthandletubetochannelassembly.Raisesandlowerstheblade.

CONTROLCABLE Connectsthelockreleaselevertotheanglelockbars.

BLADE SHOE

BLADE PIVOT SHAFT

LIFT HANDLE TUBE

BLADE PIVOT ROD

BLADE

ADJUST

SPRING

ANGLE

LOCK

BARS

LOCK RELEASE GRIP ASSEMBLY

CONTROL CABLE

LIFT HANDLE ROD

HANDLE TUBE

PULL BACK AND

LIFT UP TO

LOWER BLADE

PULL BACK AND

PUSH DOWN TO

RAISE BLADE

HANDLE GRIP

HANDLE TUBE

GRIP ASSEMBLY

LIFT ROD

Wheel weights and tire chains must be used with

your snow blade for traction. These accessories are

available at your nearest Sears retail store.

Using the Snow Blade

• Preparethelawntractorengineforcoldweather

usinginstructionsfurnishedwiththelawntractor.

• Alwaysbeginwiththetransmissioninrst(low)gear

andgraduallyincreasespeedasrequired.

• Do notrepeatedlypushsnowinthesamedirection,

causingexcessivebuildupwitheachsuccessive

pass.

• Toreduceicingontheblade,allowthelawntractor

andbladetoadjusttooutdoortemperaturebefore

operating.

• Forimprovedsnowremovalperformance,coatthe

bladewithautomotivetypepastewax.

CAUTION: Inspectcarefullythearea

tobeworkedbeforeoperatingthesnow

blade.Avoidpipes,roots,curbsorother

heavyobstructions.

CAUTION: Knowtheterrain.Avoid

exceptionallysteepslopesordropoffs

whichmaybehiddenbythesnow.

Neverrunthesnowbladeintoheavy

materialathighspeed.

CAUTION: Alwayslowerthebladeto

thegroundbeforeleavingthetractor.

 MAINTENANCESCHEDULE

Fillindatesasyou

 completeregularservice.

Beforeeachuse

Aftereachuse

ServiceDates

CUSTOMER RESPONSIBILITIES

• Readandfollowthemaintenancescheduleandthe

procedureslistedinthemaintenancesection.

Everyseason

Beforestorage

• Duringtheoperatingseason,checkallbolts,nutsand

hairpincotterstobesuretheyaresecure.

Lubrication Points

• Lubricateallpivotpointstohelpmaintainproper

operationofblade.Applyalightcoatingofgreaseto

thestraightupperportionofthelifthandlerod.See

gure24.

Checkforloosefasteners  X

 Checkforwornordamagedparts  X

 CleanBlade   X  X

 LubricateBlade    X 

FIGURE 24

MAINTENANCE

LUBRICATE

To Adjust Blade Spring

• Thetensionofthebladeadjustspringmaybealtered

topermitthebladetotiltforwardtobypasssolid

obstructions.Tochangethespringtension,adjust

thenutsatupperendofthespringbolt.Turnthenuts

counterclockwisetorelievetensionandclockwiseto

increasetension.Refertogure15onpage10.

To Adjust Blade Shoes

• Thebladeshoesattheendsofblademayberaised

forcloseworkonsmoothsurfacesorloweredtoraise

thebladetoworkonroughorunevenareas.Make

surebothshoesaresetevenlyandthatthenutsare

tightenedsecurely.Seegure25.

SERVICE AND ADJUSTMENTS

FIGURE 25

To Adjust the Blade Pivot Lock Mechanism

• Ifthebladewillnotunlockandpivot,theanglelock

barsarenotdisengagingfromtheslotsinthepivot

plate.Tocorrect,adjustthe5/16"hexjamnutstodraw

theendofthecontrolcablebacktowardsthecable

mountbracket.Thelessthethreadedendofthecable

extendsthroughthebracket,themoretheanglelock

barscanretracttodisengagefromtheslotsinthe

pivotplate.Seegure26.

FIGURE 26

Recommendations When Storing

• Whenthesnowbladeisnotbeingused,removeall

dirtandrustandtouchupwithpaint.

• Touchupbaremetalwithpaintorapplyalightcoatof

greaseorrustpreventive.

• Lubricateallpivotpointsandallpointsshownin

gure24,page14inthemaintenancesection.

• Storeinadryarea,protectedfromweather.

STORAGE

TROUBLESHOOTING

CABLE MOUNT BRACKET

5/16" HEX

JAM NUT

CONTROL

CABLE

5/16" HEX

JAM NUT

BLADE SHOE

To Remove Blade From Tractor

• Lowerthebladeheadtothegroundwiththebladein

thecenter(straightahead)position.

• Removethetwoclevispinswhichfastentheblade's

hangerbracketstothetractor'smowerdecksuspension

brackets(orframebrackets).Seegure7onpage8.

• Removetheclevispinthatfastenstheblade'srear

mountingbrackettothetractor'sdrawbaranddrop

therearofthebladeframetotheground.Seegure6

onpage8.

• Removetheframebrackets(ifused).Seegure1on

page4.

• Backthetractoroffofthebladeassembly.

PROBLEM CAUSE CORRECTION

Bladeisdifficulttoraise. Liftmechanismisbinding. Lubricatepivotpointsasshownin

gure23onpage14.

Bladeisdifficulttopivot. Handletubeisbindingonliftrod. Lubricatelifthandlerodasinstructed

onpage14.

Bladewillnotunlocktopivot. Lockmechanismisoutofadjustment

andisnotdisengaging.

RefertotheServiceandAdjustments

sectiononpage15.

Page is loading ...

ADAPTACIONES PARA DIVERSOS TRACTORES

TRACTORES DE PRADO

SEARS DE LA SERIE 917

MÉNSULA DE

SUSPENSIÓN

DEL TRACTOR

COLOQUE LAS MÉNSULAS DE

COLGAR EN EL JUEGO DE RANURAS

INTERMEDIAS EN LA VIGA DE CANAL DE EMPUJE

9,75"

(25 CM)

TRACTORES DE JARDÍN

SEARS DE LA SERIE 917

12,00"

(30 CM)

MÉNSULA DE

SUSPENSIÓN

DEL TRACTOR

COLOQUE LAS MÉNSULAS DE COLGAR

EN EL JUEGO DE RANURAS INTERMEDIAS

EN LA VIGA DE CANAL DE EMPUJE

PERNO

HEXAGONAL

DE 3/8" x 1"

PERNO DE

CARRUAJE

DE 3/8" x 1"

COLOQUE LAS MÉNSULAS DE COLGAR EN EL JUEGO DE

RANURAS DEL FRENTE EN LA VIGA DE CANAL DE EMPUJE

MÉNSULA

DE MARCO

TRACTORES SEARS DE LA SERIE 917 CON

MÉNSULA DE SUSPENSION CENTRAL (16" NEUMÁTICOS)

12,75"

(32 cm)

ARANDELA

1/2" x 1-1/4"

PERNO

HEXAGONAL

DE 5/16" x 3/4"

PERNO DE

CARRUAJE

DE 3/8" x 1"

COLOQUE LAS MÉNSULAS DE COLGAR EN EL JUEGO DE

RANURAS DEL FRENTE EN LA VIGA DE CANAL DE EMPUJE

MÉNSULA

DE MARCO

TRACTORES SEARS DE LA SERIE 917 CON

MÉNSULA DE SUSPENSION CENTRAL (15" NEUMÁTICOS)

12,75"

(32 cm)

ARANDELA

1/2" x 1-1/4"

13,00"

(33 cm)

PERNO

HEXAGONAL

DE 5/16" x 1"

TRACTORES SEARS DE LA SERIE 247 LT 2000 Y

TROY-BILT PONY TRACTORES

MÉNSULA

DE MARCO

COLOQUE LAS MÉNSULAS DE COLGAR

EN EL JUEGO DE RANURAS INTERMEDIAS

EN LA VIGA DE CANAL DE EMPUJE

PERNO

HEXAGONAL

DE 3/8" x 1"

13,00"

(33 cm)

MÉNSULA

DE MARCO

PERNO

HEXAGONAL

DE 5/16" x 3/4"

COLOQUE LAS MÉNSULAS DE COLGAR EN EL JUEGO DE

RANURAS DEL FRENTE EN LA VIGA DE CANAL DE EMPUJE

SEARS MODELO PROFESIONAL 247,2898 TRACTORES

y MTD YARD TRACTORES y TRACTORES DE JARDÍN

PERNO

HEXAGONAL

DE 3/8" x 1"

13.00"

PERNO HEXAGONAL

5/16" x 1"

COLOQUE LAS MÉNSULAS DE COLGAR

EN EL JUEGO DE RANURAS INTERMEDIAS

EN LA VIGA DE CANAL DE EMPUJE

MÉNSULA

DE MARCO

SEARS NX-15 FRAME TRACTORES

MÉNSULA

DE MARCO

COLOQUE LAS MÉNSULAS DE COLGAR

EN EL JUEGO DE RANURAS INTERMEDIAS

EN LA VIGA DE CANAL DE EMPUJE

PERNO

HEXAGONAL DE

5/16" x 3/4"

PERNO HEXAGONAL

5/16" x 1"

13.5"

SEARS 6” RADIO DE GIRO TRACTORES

Page is loading ...

FIXATION SUR DIVERS TYPES DE TRACTEURS

BOULON HEX

3/8 PO. x 1 PO.

BOULON HEX

3/8 PO. x 1 PO.

BOULON HEX

5/16 PO. x 1 PO.

BOULON HEX

5/16 PO. x 3/4 PO.

SEARS 247.2898 PROFESSIONNEL SÉRIE TRACTEURS

ET MTD YARD TRACTEURS ET TRACTEURS DE JARDIN

TRACTEURS SEARS DE LA SÉRIE 917 ET HUSQVARNA

AVEC SUPPORT DE SUSPENSION CENTRAL (40 CM. PNEUS)

TRACTEURS SEARS DE LA SÉRIE 917 ET HUSQVARNA

AVEC SUPPORT DE SUSPENSION CENTRAL (38 CM. PNEUS)

12,75 PO.

(32 CM)

BOULON HEX

3/8 PO. x 1 PO.

RONDELLE 1/2 PO.

x 1-1/2 PO.

BOULON DE

CARROSSERIE,

3/8 PO. x 1 PO.

PLACEZ LES SUPPORTS EN ÉQUERRE DANS LES

FENTES CENTRALES DE LA BARRE DE POUSSÉE

PLACEZ LES SUPPORTS EN ÉQUERRE DANS LES

FENTES CENTRALES DE LA BARRE DE POUSSÉE

SUPPORT

DE CHÂSSIS

TRACTEURS DE PELOUSE

(SEARS DE LA SÉRIE 917 ET HUSQVARNA)

SUPPORT DE

SUSPENSION DU

TRACTEUR

PLACEZ LES SUPPORTS EN ÉQUERRE DANS LES

FENTES CENTRALES DE LA BARRE DE POUSSÉE

PLACEZ LES SUPPORTS EN ÉQUERRE DANS LES

FENTES CENTRALES DE LA BARRE DE POUSSÉE

TRACTEURS DE JARDIN

(SEARS DE LA SÉRIE 917 ET HUSQVARNA)

12 PO.

(30CM)

SUPPORT DE

SUSPENSION

DU TRACTEUR

PLACEZ LES SUPPORTS EN ÉQUERRE

DANS LES FENTES CENTRALES DE LA BARRE DE POUSSÉE

9,75 PO.

(24 CM)

SUPPORT DE

SUSPENSION DU

TRACTEUR

SUPPORT DE

SUSPENSION DU

TRACTEUR

13 PO.

(33 CM)

BOULON DE

CARROSSERIE,

3/8 PO. x 1 PO.

SUPPORT

DE CHÂSSIS

PLACEZ LES SUPPORTS EN ÉQUERRE DANS LES

FENTES SITUÉES À L'AVANT DE LA BARRE DE POUSSÉE

TRACTEURS SEARS DE LA SÉRIE 247 LT 2000

ET TROY-BILT PONY

BOULON HEX

5/16 PO. x 3/4 PO.

RONDELLE 1/2 PO.

x 1-1/2 PO.

13 PO.

(33 CM)

12,75 PO.

(32 CM)

13.00"

BOULON HEX

5/16 PO. x 1 PO.

PLACEZ LES SUPPORTS EN ÉQUERRE DANS LES

FENTES CENTRALES DE LA BARRE DE POUSSÉE

SUPPORT DE

SUSPENSION DU

TRACTEUR

SEARS NX-15 FRAME TRACTEURS

SUPPORT DE

SUSPENSION DU

TRACTEUR

PLACEZ LES SUPPORTS EN ÉQUERRE DANS LES

FENTES CENTRALES DE LA BARRE DE POUSSÉE

BOULON HEX

5/16 PO. x 3/4 PO.

BOULON HEX

5/16 PO. x 1 PO.

13.5"

SEARS 6” RAYON DE BRAQUAGE TRACTEURS

Page is loading ...

REPAIR PARTS LIST FOR MODEL LBD48E 48" SNOW BLADE

44, 63

6, 52

63, 64

OPTIONAL ACCESSORY

the fastest way to purchase parts

www.speedepart.com

REPAIR PARTS LIST FOR MODEL LBD48E 48" SNOW BLADE

REF.

NO.

PART

NO.

QTY. DESCRIPTION

1 23955 1 Blade48"

2 23956 1 WearPlate48"

3 62980 1 ReinforcementPlateAssembly

4 43080 6 Bolt,Carriage5/16-18x3/4"

5 44326 4 Bolt,Carriage5/16-18x1"

6 47810 17 NylonLockNut,5/16-18

7 43081 4 Washer,5/16"

8 24690 2 SkidShoe

9 64732 1 ThrustChannel

10 24347 1 PushChannel

11 43262 1 HexLockNut,1/2-13

12 23131 1 Bolt,SpecialPivot

13 1540-118 1 Washer,Flat1/2"

14 23958 1 Plate,Pivot7Ga.

15 23130 1 Bracket,SpringMt.

16 24659 2 RearSupportChannel

17 46066 1 Shaft,BladePivot

18 25125 1 RearMountingBracket

19 9466R 1 Spring,BladeAdjust

20 44071 1 HexBolt,3/8-16x3-1/2"

21 43015 2 HexNut,3/8-16

22 44074 1 PlasticCap

23 49808 1 ControlCableAssembly

24 62561 1 ReleaseGripAssembly

25 43055 4 Pin,HairpinSmall3/32"

26 46053 2 Spacer,.28IDx1"

27 63033 1 LiftHandleRodAssembly

28 25121 1 ShortHangerBracket

29 25122 1 LongHangerBracket

30 24023 1 PivotSupportBracket

31 48167 1 Rod,BladePivot

32 65519 1 LiftHandleTubeAssembly

33 23151 2 AngleLockBar

34 23856 1 SpringMountRod

35 44917 2 Palnut,3/8"

REF.

NO.

PART

NO.

QTY. DESCRIPTION

36 43010 3 CotterPin1/8"x1-1/4"

37 43348 1 AngleLockSpring

38 746-0260 2 CableEndFitting

39 731-0869 1 Grip,Plastic

40 46471 1 Handle,Grip

41 712-0256 2 HexJamNut,5/16-24

42 23658 1 Spacer

43 43085 1 HexBolt,5/16-18x1-1/2"

44 43063 4 Bolt,Hex5/16-18x1"

45 05762 1 CableMountBracket

46 1509-90 1 HexBolt1/4-20x1-1/4"

47 47189 3 NylonLockNut,1/4-20

48 710-0305 4 CarriageBolt,3/8-16x1-1/4"

49 46065 1 ChannelPivotPin

50 63034 1 LiftLinkAssembly

51 43350 12 CarriageBolt,3/8-16x1"

52 HA21362 20 NylonLockNut,3/8-16

53 HA23380 1 RearLocatingBracket

54 726-0178 2 PlasticTie

55 R19171616 3 Washer.1/2"x1"x.059"Thin

56 46071 1 HexBolt,1/4-20x3-1/4"

57 43349 1 1/4"x1"SpringPin

58 43343 3 Pin,3/32"Hairpin(Large)

59 44062 2 ClevisPin,1/2"x1"Lg.

60 HA3980 1 ClevisPin,5/8"x1-3/4"Lg.

61 25124 2 FrameBracket

62 43003 2 LockWasher,3/8"

63 43001 8 HexBolt,3/8-16x1"

64 47630 2 HexBolt,5/16-18x3/4"SelfThd

65 R19172410 4 Washer,1/2"x1-1/2"x.134"

66 66754 1 RubberBladeKit(notincluded)

67 43087 2 HexBolt,3/8x1-1/4"

68 43070 2 Washer,3/8"

69 47572 4 FlangedLockNut,3/8-16

41860 1 OwnersManual

the fastest way to purchase parts

www.speedepart.com

REPAIR PARTS

Agri-Fab,Inc.

809SouthHamilton

Sullivan,IL.61951

217-728-8388

Agri-Fab LBD48 User guide

Brand: Agri-Fab

Model: LBD48

Type: User guide

Download PDF

report

in other languages

français: Agri-Fab LBD48 Mode d'emploi
español: Agri-Fab LBD48 Guía del usuario

Agri-Fab LBD48 User guide

Agri-Fab LBD48 User guide

in other languages

Related papers

Other documents