MTHTrains 30-5134-1 User manual

Brand: MTHTrains

Model: 30-5134-1

Type: User manual

This manual is also suitable for

PLEASE READ BEFORE USE AND SAVE

www.mthtrains.com

RailKing PCC Electric Street Car

OPERATOR’S MANUAL

Compatibility

The PCC Electric Street Car will operate

on any traditional O-31 Gauge track

system, including M.T.H.’s RealTrax® or

ScaleTrax™ or traditional tubular track.

It is also compatible with most standard

AC transformers. (See pages 43 and 44

for a complete list of compatible

transformers, power packs and wiring

instructions.)

Transit Announcements

This product may be protected by one or more of the following patents: 6,019,289; 6,280,278; 6,281,606; 6,291,263;

6,457,681; 6,491,263; 6,604,641; 6,619,594; 6,624,537; 6,655,640.

CAUTION: ELECTRICALLY OPERATED PRODUCT:

WARNING: When using electrical products, basic safety precautions should be observed, including the following:

- Read this manual thoroughly before using this device.

- M.T.H. recommends that all users and persons supervising use examine the hobby transformer and other electronic equipment

periodically for conditions that may result in the risk of fire, electric shock, or injury to persons, such as damage to the primary cord,

plug blades, housing, output jacks or other parts. In the event such conditions exist, the train set should not be used until properly

repaired.

- Do not operate your layout unattended. Obstructed accessories or stalled trains may overheat, resulting in damage to your layout.

- This train set is intended for indoor use. Do not use if water is present. Serious injury or fatality may result.

- Do not operate the hobby transformer with damaged cord, plug, switches, buttons or case.

Recommended for Ages 14 and up. Not recommended for children under 14 years of age without adult supervision.

As with all electric products, precautions should be observed during handling and use to prevent electric shock.

Table of Contents

Before you Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Set Up Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

PS 3.0 Enhancements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Conventional AC/DC Start-up/Shut-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

DCS/DCC Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Programming Track (for DCC operation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Loading Engine Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Conventional AC Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Proto-Sound 3.0 Conventional AC Operating Instructions . . . . . . . . . . . . . . . 7

Activating Proto-Sound 3.0 Conventional AC Mode Features . . . . . . . . . . . . . 7

Manual Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

TAS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Speed Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Locking Locomotive Into A Direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Reset To Factory Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Automatic Sound Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Conventional DC Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

DCS Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

DCC/Digital Command Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Basic DCC Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Start up/Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Master Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Forward/Reverse Signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Engine Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Additional F Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Function Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

CV29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Long and Short Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Feature/Factory Resetting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

55-55-55 Address Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

M.T.H. Proto-Sound 3.0 Expanded DCC Functionality . . . . . . . . . . . . . . . . . . . . . . . 24

Advanced DCC Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Configuration Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Advanced Consisting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Programming Track. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Lubricating and Greasing Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Cleaning The Wheels, Tires and Track. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Light Replacement Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Troubleshooting Proto-Sound 3.0 Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Transformer Compatibility and Wiring Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

DC Power Supply Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Additional Features Accessible Of DCS Remote Control System . . . . . . . . . . . . . . . . . 45

Service & Warranty Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Limited One-Year Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Rev: _RK PCC Electric Street Car 3/3/15

BEFORE YOU BEGIN

By visiting the M.T.H. website, www.mthtrains.com, you will be able to view any

additional manual updates that affect your PCC Car. Enter the MTH Item number of

the PCC Car you want to check and select the manual icon to download or view it. You

will need Adobe Acrobat Reader to view the manual.

Order online: www.mthtrains.com, e-mail: parts@mth-

railking.com, Fax: 410-423-0009, Phone: 410-381-2580, Mail: 7020 Columbia Gateway

Drive, Columbia MD 21046-1532

Set Up Checklist

• Lubricate Engine

• Read all General Maintenance and Operation Instructions

• Apply power to run as described in the Modes of Operation

Lubrication

You should lubricate the engine to prevent it from squeaking and

to prevent excessive wear. Use light household oil and follow the

lubrication points marked “L” (shown below). Do not over-oil.

Use only a drop or two on each pivot point.

You can obtain replacement parts and replacement instructions from the

M.T.H. Parts Department.

RailKing PCC Electric Street Car w/ Proto-Sound 3.0

DO NOT

OVER OIL

O NOT

OVER OIL

Figure 1: Lubrication Points on the Locomotive

Lubricate Pick Up Roller Axles (L)

Lubricate All Wheel Axles (L)

PS 3.0 Enhancements

There are 4 options for operating your MTH Proto-Sound 3.0-equipped engine;

• Conventional AC

• Conventional DC

• DCS [MTH Digital Command System]

• DCC (DCC/DCS Switch Required)

When the locomotive is placed on the track and power is applied to the track the

locomotive will detect the type of control system being used and respond accordingly.

Below is an overview of the 4 different systems.

NOTE: You’ll need to install a DCC/DCS switch and then make sure you have

the DCC/DCS switch set correctly if you’re using one of those two modes.

Here are some of the exciting changes incorporated into your new MTH Proto-Sound

3.0 Locomotives. More advanced features such as Custom Speed Tables and Advanced

Consisting can be found in the DCC section of this manual.

Conventional (Analog) AC/DC Start-up/Shut-down

Your new MTH PS3.0-equipped locomotive no longer has batteries. It uses Super

Capacitors to hold the engine board alive for a short time when you shut off or

interrupt track power. Because of this, when you first apply track power to your PS3.0-

equipped O Gauge engine, you will notice the headlight comes on but nothing else. This

is perfectly normal. The capacitors are charging up during this time. The wait time

depends upon how long it’s been since you last applied power to the engine. Typically it

will take 1-15 seconds to fully charge. NOTE: The 1-15 second charging wait time

ONLY applies to conventional AC track power.

Once the headlight shuts off, the engine will play its start-up sounds and all the lights

will come back on, simultaneously.

The capacitors hold enough charge to play the full shut-down sounds. Also, the

capacitors allow you to operate your engine in conventional mode just like you would

any other conventionally-controlled engine. Finally, because there are no batteries, you

will notice there is no external charge jack on the engine.

RailKing PCC Electric Street Car w/ Proto-Sound® 3.0

DCS/DCC Switch (Activating DCC Mode)

Even though your locomotive is equipped with a DCC decoder, you will notice that there

is no switch to select it. We found that when the switch was present, it was confusing to

those who are not familiar with DCC operations. In order to operate in DCC you must

install a DCS/DCC switch. If you operate in DCS or conventional mode it is not

necessary to install the DCS/DCC switch.

The DCS/DCC switch may be purchased directly from the M.T.H. Parts Department.

Order Online: www.mthtrains.com, E-mail: parts@mth-railking.com,

Fax: 410-423-0009, Phone: 410-381-2580, Mail: 7020 Columbia Gateway Drive,

Columbia, MD 21046-1532

Programming Track (for DCC operation)

Your MTH PS3.0-equipped O Gauge engine can function on Programming Track outputs

from DCC systems. Most DCC systems can support the current requirements of the

engine as long as it’s not started up. If you plan on powering up the MTH engine on your

programming track, you may want to consider a DCC Programming Track Booster.

Loading Engine Firmware

Your new MTH PS3.0-equipped O-Gauge engine affords you the ability to load Engine

firmware. Loader version 2.30 or later will allow you to do this. Please refer to the Loader

program’s instructions for more details. So, as MTH releases new features or updates you

will be able to take full advantage without having to ship your favorite engine anywhere.

All new updates are available on our website. MTH will make announcements as they are

available. Not all updates will apply to all engines. NOTE: Requires a TIU w/ version

4.20 or later firmware, and requires Consumer Loader version 2.30 or later.

RailKing PCC Electric Street Car w/ Proto-Sound® 3.0

CAUTION:

Do not apply DCS signals

and DCC signals to the same

track simultaneously. The

signals are not compatible,

mixing the DCS and DCC

signals will damage the DCS

TIU unit.

DCS/DCC Switch Location

Figure 2: DCS/DCC Switch Location

Modes of Operation

The following pages have detailed descriptions of the 4 different modes of operation:

• Conventional AC

• Conventional DC

• DCS [MTH Digital Command System]

• DCC (DCC/DCS Switch Required)

Conventional AC Operation

When using conventional AC power, the engine will respond to changes in track voltage.

An increase in track voltage will increase the locomotive speed and a reduction in track

voltage will reduce the engine speed.

A short interruption (approximately 1 to 2 seconds) in the track voltage will cause the

engine to cycle in the sequence for each track voltage interruption (neutral – forward –

neutral – reverse) When power is first applied to the track, the locomotive will be silent

for 1-20 seconds and the headlight will be on, indicating the super capacitors are

charging (The super capacitors provide power to the sound system during direction

changes or intermittent drops in track power due to dirty track switches, when

operating in conventional mode). When the super capacitors are charged, all the lights

will come on and the engine sounds will start up. There should be no movement, as the

engine is in neutral. Causing a short interruption of track power by using the direction

button on the transformer, or by bringing the throttle to 0 volts and back again, will

change the sequence to the forward state. Then increasing the throttle will begin to move

the engine forward, and speed will increase as the throttle is advanced.

If there is another interruption in track power the sequence will change to the neutral

position again. The engine will remain in the neutral state until there is another

interruption in track power. The next interruption in track power will move the sequence

to the reverse state. The engine will now move in the reverse direction. If the power

interruption was accomplished by using the direction button and the throttle position

was not changed, the engine will run in the reverse direction at the same speed that it

was traveling in the forward position.

Subsequent interruptions in track power of 1-2 seconds will continue the sequence

rotation. If you happen to interrupt track power for longer than about 2 seconds, the

engine will begin its shut down sounds. If this occurs you can cycle the direction

sequence again to get back to the direction you wish to move and once the engine starts

moving its shut down sounds will stop playing (SEE PAGE 7 (direction cycle phases)).

In conventional AC operation the whistle sound, the bell sound, TAS sounds and other

operational functions can be accessed if your transformer has a horn/whistle button and

a bell button. By using combinations of button presses, different commands besides

blowing the whistle and ringing the bell can be initiated.

or on

RailKing PCC Electric Street Car w/ Proto-Sound® 3.0

Proto-Sound 3.0 Conventional AC

Operating Instructions

Activating Proto-Sound 3.0 Conventional AC Mode Features

Throttle - To increase or decrease track voltage, and therefore train speed, turn the

throttle control knob. Turning clockwise will increase voltage and speed, while turning

counterclockwise will decrease voltage and speed. The engine will maintain the speed

you set after you release the throttle until you turn it again to change the voltage and

speed.

Bell - To sound the bell, in an engine equipped with a bell firmly press and release the

Bell button. To turn the bell off, press and release the Bell button again. The bell will

continue to ring from the time you turn it on until you press and release the button

again to turn it off.

Horn/Whistle - To sound the whistle, firmly press the Horn/Whistle button. The

whistle will sound for as long as you continue to depress the button. It will stop when

you release the button.

Direction - Your train is programmed to start in neutral. The train will always cycle

neutral-forward-neutral-reverse with each press and release of the direction button.

The engine is programmed to restart in neutral each time the track voltage is turned off

for 25 seconds or more.

Cycle Phases

Neutral

ForwardReverse

RailKing PCC Electric Street Car w/ Proto-Sound® 3.0

Proto-Sound 3.0

Manual Volume Control

Figure 3: Manual Volume Control

Proto-Sound 3.0 features are activated by sequences of Bell and Horn button pushes

described below. Please read the full descriptions of each feature before using it. To use

these buttons to activate features rather than to blow the horn or ring the bell, you should

tap the buttons very quickly with a ½-second pause between button presses. You may

need to practice your timing to make this work smoothly.

Timing Chart

Total Time Lapse: 1 Seconds½

Press

Horn

Short &

Firm

½ Sec.

Pause

½ Sec.

Pause

Press

Bell

Short &

Firm

Press

Bell

Short &

Firm

Manual Volume Control

To adjust the volume of all sounds

made by this engine, turn the manual

volume control (fig. 3) clockwise

to increase the volume and

counterclockwise to reduce the

volume. Turning the manual volume

control completely counterclockwise

will turn off all of the engine sounds

and announcements.

RailKing PCC Electric Street Car w/ Proto-Sound® 3.0

Operating Modes

1. Manual Mode

Upon initial power application, the engine will start up in manual mode. The chart below

lists the features available to the operator when in Manual Mode. Different features are

available when operating in Learn and Auto Modes, which are described later.

Button Code

Function Manual Mode

Function Learn Mode

Function Auto Mode

Feature to Be Activated

Button Code

Fire Coupler (if equipped) 1 Bell, 3 Horn/Whistle

Speed Control On/Off 1 Horn/Whistle, 2 Bells (from Neutral only)

Lock into a Direction 1 Horn/Whistle, 3 Bells

Reset to Factory Defaults 1 Horn/Whistle, 5 Bells (from Neutral only)

(including default Auto Mode route settings)

Transit Announcement Sounds 1 Bell (depress button approx. 2 secs.)

To Enter Learn Mode 1 Horn, 4 Bells

To Stop at Each Station Direction

To Scroll through the Station Names Bell (hold to scroll and release as soon

as you hear the desired station name)

To Save Station Horn (hold for "Saved" response)

To Enter Auto Mode from Manual Mode 1 Bell, 2 Horn at the location of the first

programmed station stop

To Begin Programmed Run Direction

To Enter Manual Mode from Auto Mode 1 Bell, 2 Whistles

Transit Announcement Sounds (TAS)

Your Proto-Sound 3.0 street car is equipped with operator controlled Transit

Announcement Sounds, hereafter known as TAS. This easy-to-use feature plays digitally

reproduced transit announcements and platform action sounds whenever you activate and

stop your engine. No additional wires or modifications are needed on your layout to enjoy

these amazing sound effects. These different sounds are heard each time you give a long

bell button press. The entire TAS sequence is designed to simulate thearrival,

disembarking, embarking, and departure of a transit stop. The sounds include the driver

announcing the stop and the upcoming stop, passenger disembarking and embarking

sounds, driver to passenger requests, door openings and closing and general transit stop

sounds. After the station sounds have finished, the engine will shift back into gear and, if

the throttle is set high enough, will pull away from the station.

To activate the TAS, press and hold the bell button for approximately 2 seconds.

If you do not wish to stop at the station that is announced after activating TAS, press and

hold the bell button again without throttling down the train.

2. Learn Mode

In Learn Mode, the engine may be programmed with either an "Out & Back" route or a

"Loop" route. An "Out & Back" route begins at the 1st station (as programmed by the

operator), stops at intermediate stations, ends at the last station, then reverses its route

until it reaches the 1st station. A "Loop" route begins at the 1st station (as programmed by

the operator), stops at intermediate stations, ends at the last station, and then begins the

route over again at the 1st station.

Example Of An Out-and-Back:

Example Of A Loop:

RailKing PCC Electric Street Car w/ Proto-Sound® 3.0

T.A.S.

(On/Off)

Bell

(depress button

approx. 2 secs.)

To program stations:

1. Running in Forward, stop the unit at the desired location for the first stop by pressing

the direction button. Note: if you stop the engine with the throttle control, you must

re-apply power so that the engine goes into neutral and does not shut down.

2. Enter Learn Mode by pressing Horn-Bell-Bell-Bell-Bell. The train will then announce

that you have entered Learn Mode.

3. Press and hold the Bell button to scroll through the available stations until you hear the

one that you would like to be your first stop. Release the button quickly as soon as you

have heard the desired stop name.

4. Press and hold the Horn button until a "saved" response confirms that station's

location and name are saved in memory.

5. Proceed to the next stop by pressing the Direction button.

6. Press the Direction button to stop the train again when you have reached the next

desired station location.

7. Using the Bell button, select the name of the station, then save using the Horn button.

8. Repeat steps 5-7 until you are ready to program the last stop in the route.

9. The manner of saving the last station in the route determines whether the route will be

an "Out & Back" or "Loop" route.

“Out & Back”

Follow steps 5-7 to save the last station. After you press the Horn button and the sound

system plays the "Saved" confirmation, press the Horn button again. Another "Saved"

confirmation will play and the car will exit Learn Mode and enter Manual Mode.

“Loop”

Follow steps 5-7 to save the last station. Press the Direction button once to start the car in

forward and stop the car at the location of the first stop by pressing the Direction button.

Press the Bell button as many times as is necessary to hear the name of the first stop.

Press the Horn button until the "Saved" confirmation is played. The car will then

automatically exit Learn Mode and enter Manual Mode.

Notes: Always approach a desired station stop location while running in Forward. Learn

mode counts distance traveled, not actual physical locations. However, unlike an

automobile's odometer, Proto-Sound 3.0 Learn Mode does erase distance when traveling

in reverse. If you operate your car past the desired stop location, you may back it up to the

desired stop location, however you must put the car into forward and then neutral again

before saving the stop name and location into memory.

3. Auto Mode

When you have finished programming your stations in Learn Mode the car will be in

Manual Mode. Running in Forward, stop the car at the location of the first programmed

station by pressing the Direction button. Press Bell-Horn-Horn to put the train into

Auto Mode. Press the Direction button again to begin operation in Auto Mode. Because

Auto Mode operation begins at the first stop, the next stop announced will be the

second stop.

RailKing PCC Electric Street Car w/ Proto-Sound® 3.0

Speed Control

M.T.H. engines equipped with Proto-Sound 3.0 have speed control capabilities that allow

the engine to maintain a constant speed up and down grades and around curves, much like

an automobile cruise control. You can add or drop cars on the run, and the engine will

maintain the speed you set.

While the engine is programmed to start with the speed control feature activated, you

can opt to turn it off. This means the engine's speed will fall as it labors up a hill and

increase as it travels downward. It is also affected by the addition or releasing of cars

while on the run. Because the engine will run more slowly at a given throttle voltage

when speed control is on than when it is off, you should adjust the throttle to a lower

power level for operation with speed control off to avoid high-speed derailments.

When speed control is off, the volume will drop to allow for better low voltage

operation.

To turn speed control on and off, put the engine in neutral, then quickly tap the

transformer's Horn button one time then quickly tap the Bell button two times,

allowing approximately ½ second to lapse between each quick button press. Two horn

blasts will indicate that the engine has made the change. Repeat the 1 horn, 2 bells code

to return it to the other condition. You will want to do this during the initial neutral

upon start-up if you ever couple this engine to another engine that is not equipped with

speed control to avoid damaging the motors in either engine. Each time you shut down

the engine completely, it will automatically turn speed control on.

Horn

Place

Engine into

Neutral

Bell Bell

Speed Control

Two Horn Blasts

(indicates change is made)

Repeat to Return

to Normal Condition

Locking Locomotive Into A Direction

You can lock your engine into a direction (forward, neutral, or reverse) so that it will

not change directions. To do this, put the engine into the direction you want (or into

neutral to lock it into neutral), run it at a very slow crawl (as slowly as it will move

without halting), and quickly but firmly tap the Horn button once followed by three

quick taps of the Bell button, allowing approximately ½ second to lapse between each

quick button press. Two horn blasts will indicate that the engine has made the change.

The engine will not change direction (including going into neutral) until you repeat the

1 horn, 3 bells code to return the engine to its normal condition, even if the engine is

kept without power for extended periods of time.

Horn

Place

Engine into

Desired

Direction

Horn

Bell Bell Bell

Direction Lock

Two Horn Blasts

(indicates change is made)

Repeat to Return

to Normal Condition

RailKing PCC Electric Street Car w/ Proto-Sound® 3.0

Automatic Sound Effects

Certain Proto-Sound 3.0 sound effects automatically play in programmed conventional

mode conditions:

• Squealing Brakes play any time the engine’s speed decreases rapidly.

• Cab Chatter plays at random intervals when the engine idles in neutral.

• Engine Start-up and Shut-down sounds play when the engine is initially

powered on or is powered off for five seconds or more.

Reset to Factory Default

To override the settings you currently have assigned to the engine and reset it to its factory

defaults, while in Neutral tap the Horn button quickly once, followed by five quick taps of

the Bell button, allowing approximately ½ second to lapse between each quick button

press. Two horn blasts will indicate that the engine has made the change.

Reset

Two Horn Blasts

(indicates change is made)

Repeat to Return

to Normal Condition

Horn

Place

Engine in

Neutral

BellBellBellBellBell

Conventional DC Operation

Your MTH locomotive will operate on conventional DC track voltage also. However,

functions such as sounding the horn, ringing the bell and the TAS sounds cannot be

initiated in conventional DC. Only the diesel engine sounds, smoke, squealing brakes and

idle sounds will function.

Operation of your MTH Proto-Sound® 3.0 engine in conventional DC is very similar to

operating a conventional AC engine. As you increase track voltage, engine speed increases.

As the track voltage is decreased, engine speed is decreased. When track voltage polarity is

reversed using the polarity or direction switch on the power pack, the engine will run in

the opposite direction. The electronics in your MTH Proto-Sound® 3.0 locomotive are

designed to slowly change direction without a need to change the throttle, if you so desire.

Just change the polarity switch on your DC power pack and the engine will gradually come

to a stop and then automatically begin traveling in the opposite direction. The speed will

build up to the same speed that the engine was going in the previous direction. When

power is first applied to the locomotive, the engine’s sounds will start up when the track

voltage reaches about 8 VDC. To get your locomotive moving, after the startup sounds

have finished and the locomotive is idling, slowly increase the track voltage until the

locomotive is traveling at the desired speed.

NOTE: If you apply more than 9.0VDC to the engine at start-up the engine will not

move. This is normal. We refer to this as “Anti-Jackrabbit” and this feature prevents

your model from taking off at high track voltages. Simply lower the track voltage down

below 9.0VDC and then back up to get your engine moving. This applies only when you

start up your engine.

RailKing PCC Electric Street Car w/ Proto-Sound® 3.0

DCS - Digital Command System

While the acronyms are close, this is where the similarity ends between DCC and DCS.

Yes they are both digital control systems. However, M.T.H. DCS is not DCC. There are

several proprietary versions of DCC on the market, but DCS is not one of them.

M.T.H.'s DCS System is a proven technology in the O Gauge, One Gauge, and HO

Gauge markets. First the power signal in DCS is not the command signal. Next DCS

employs a fully functional bi-directional communication scheme opening a vast range of

advanced features and yet so simple and intuitive that you can enjoy them. No

programming tracks, bits and bytes, or conversion of binary to hexadecimal numbers

here. To add an engine in DCS, press “ADD ENGINE”. After that, if you want to start

your engine just press “START UP” or to turn the smoke unit on or off, just press

“SMOKE”. No combination of letters or numbers to remember.

Additional details can be found in the DCS manual that accompanies your DCS system

or on the MTH Web site, www.mthtrains.com With DCS, you can have a whole fleet of

MTH PS 3.0 engines on the rails and they will remain shut down until you command

them to start up.

DCC - Digital Command Control

DCC is a popular digital command scheme wherein the track power is also a digital

control signal. That is, using a DCC controller, you can communicate with multiple

engines and have all of them moving at different speeds and in varying directions on

the same track at the same time. The power/command signal remains constant and

engines are commanded to perform as desired. Your MTH PS3.0-equipped engine has

the ability to decode and respond to these DCC commands. This allows you to mix and

match MTH PS3—equipped engines as well as operate them with any other

manufacturer's DCC-decoder equipped engine. The best part about your MTH PS3.0-

equipped engine is that the decoder is built right in. No need to remove the hood and

install speakers or boards. It's all done for you at the factory. Each PS3.0-equipped

engine has a full complement of lights, sounds, smoke (if equipped). Just set the model

on the rails, apply DCC power and hit F3 on your DCC handheld controller and you're

off and running.

(DCC/DCS Switch Required)

RailKing PCC Electric Street Car w/ Proto-Sound® 3.0

Basic DCC Operation

Your MTH PS3.0-equipped engine takes full advantage of DCC's capabilities. Below are

the basic commands you'll want to know to get started running quickly. Please refer to

the Advanced DCC Operation section of the manual if you want to dig into the full

capability of DCC.

Each engine type may have a slightly different F Function list. This depends upon

whether it's steam, diesel, or electric and whether it has smoke or not. Please refer to the

table of Default CV Values for your particular engine's F Functions.

A note about enabling/disabling F Functions in DCC - Depending upon the DCC

system you have you may need to toggle a particular F Function on then off to actually

get it to enable. Some DCC systems do this for you automatically and others allow you

to set particular F Function buttons to either be set for momentary or toggle. Please

refer to your DCC control station manufacturer's manual for more information on how

they handle F Function buttons.

Your MTH PS3.0-equipped engine's default short address is 3. So all you have to

do is power up your DCC system and call up Locomotive 3 to begin.

Start-Up/Shut-Down

F3 – Start-Up/Shut-Down

Pressing this twice (toggle on then off) will start up your engine. When you apply DCC

power your MTH PS3.0-equipped engine will remain dark and quiet. Since you likely

don't want to run the engine this way, simply press F3 twice to start your engine. The

lights, sound and smoke (if equipped) will come on.

Note – You are actually able to move the engine in DCC without starting it up. Just

increasing the throttle will cause the engine to move. In order for F3 to function

correctly the engine must NOT be moving.

To shut your engine down, press the F3 button twice. This will play the shut down sounds

and then turn the lights and smoke and sounds off. As long as there is DCC power still on

the track the engine can be started up again by pressing the F3 button twice.

Bell/Whistle (Horn)

F1 – Bell

To activate the Bell press F1. To deactivate it, hit F1 again.

F2 – Whistle (Horn)

To activate the Whistle/Horn, press F2. To shut it off either let off the F2 button or

press and release it.

RailKing PCC Electric Street Car w/ Proto-Sound® 3.0

Lights

F0 – Headlight/Taillight

This toggles your headlight/taillight on and off.

F5 – Lights

This toggles your firebox and cab interior light on and off.

Master Volume

F6 – Master Volume

There are 10 volume levels. Pressing F6 twice (toggling on then off) raises the Master

Volume one level. The Master Volume loops. That is, if you go past the 10th level it will

loop back around to the 1st or lowest volume level.

Forward/Reverse Signal

Just like a real engine, you can announce the direction of intended movement using

your DCC handheld and F9 and F10.

F9 – Forward Signal

Pressing F9 twice (toggling on then off) will sound the Forward Signal. This is two

whistle/horn blasts.

F10 – Reverse Signal

Pressing F10 twice (toggling on then off) will sound the Reverse Signal. This is three

whistle/horn blasts.

Engine Sounds

F25 – Engine Sounds

You can turn the Engine Sounds On/Off by pressing the F25 button. Pressing it once

(enabling F25) will cause the Engine Sounds to shut off. The Whistle/Horn and Bell

sounds will still be active, however. To turn the engine sounds back on press the F25

button again (disable F25).

RailKing PCC Electric Street Car w/ Proto-Sound® 3.0

Additional F Functions

F4 – Station Announcement

Please refer to page 9 for a description of this feature. The operation instructions

follow.

Note: F4 has two functions with trolley/subways:

1. It scrolls through the station announcements to allow you to pick a specific station to

stop at in Manual Mode.

2. It scrolls though the station announcements to allow you to pick the station stop you

want to program while the engine is in Learn Mode.

Depending upon how you have F4 set to function (toggle or momentary) you will want

to turn F4 On then Off to get the station announcement to play. It is best to follow the

table above for the specific operation for each F-Function.

Manual Mode Operation using F4:

1. While the engine is moving press F4 so it goes On then Off. You will hear a station

announcement (for example, “Next Stop, Times Square.”).

2. Manually drive the engine to where you’d like it to stop and bring the speed to zero.

3. The engine will begin playing its random station sounds. These are sounds of a

station that include all the ambient noises one might hear.

4. Once you are ready to depart the station simply roll the throttle up to your desired

speed and the engine will wrap up its station sounds and play a departing

announcement. Shortly after it will start moving.

5. You can repeat this process as often as you like. You can also scroll through the list

of stations to get to one in particular you’d like it to stop at. The last station

announcement the engine makes is the one it will stop at. If you happen to go past the

one you want you can continue toggling F4 until you hear it again. The station

announcements loop around in the list.

F7 – Auto Mode

Auto Mode is a mode of operation that allows the engine to run along a pre-

programmed route that you have taught it. When F7 is On the engine will announce

“Auto Mode”. Toggling F7 Off will shut off Auto Mode and put the engine back into

Manual Mode. The engine will not announce that it’s in Manual Mode, however. Again,

please refer to the table above for how the F-Function buttons should be working to get

the desired results.

RailKing PCC Electric Street Car w/ Proto-Sound® 3.0

F8 – Learn Mode

Learn Mode is a mode of operation that allows you to teach the engine when and where

to stop. By using the F4 and F8 function buttons you can program stops along a route.

Here’s how this works:

1. Ensure the engine is stopped at the first station as close as possible to exactly where

you want it to stop (and start). It is important that you get this as close as possible

because any errors you have in programming will become cumulative along the entire

route.

2. Press F8 so it is On (ensure it is left On the entire time you are programming the

engine’s route. The engine will announce “Learn Mode”.

3. Assuming your engine is exactly where you want your first stop press the F4 button

On then Off (again, this depends upon how you have the functionality of some F-

Function Buttons). The first station in the list will be announced. If this is the station

you want to program press F2 On then Off. The engine will announce, “Saved”. It’s a

good idea to write down the stations in the order in which you save them. This is

especially important for the final step of saving the final stop.

4. Continue on programming station by advancing the throttle and stopping at the next

station. Repeat step 3 and 4 for as many stations you want to program.

PLEASE READ THE FOLLOWING STEP AS IT’S EXTREMELY IMPORTANT

5. This step shows you how to save the final station. The method in which you save the

final station determines whether your route is an out-and-back or loop:

a. To save as a Loop:

I. Ensure the engine is back at the EXACT same spot you started.

ii. Using F4 cycle through the station list until you hear the first station you

programmed in step 3.

iii. Press F2 On/Off to save the station. The engine will announce “Saved.

Save Complete” and the engine will go back to the normal engine sounds.

b. To save as an Out-and-Back:

i. Ensure the engine is sitting at the final station you programmed in step 4.

ii. Press F2 On/Off again and the engine will announce, “Save Complete” and

the engine will go back to the normal engine sounds.

iii. Advance the throttle and drive the engine to the first station you saved.

You are now ready to run the engine in Auto Mode (F7).

To run in Auto Mode:

1. Drive or set the engine at the first station you programmed earlier. It’s important that

you be as exact as possible where you start the engine to minimize any drift the engine

might have from the physical station stop.

2. Press F7 so it’s On. The engine will announce, “Auto Mode”.

3. Advance the throttle and the engine will automatically stop at the pre=-programmed

stops.

To make it stop at All or Random stations see the section on All/Random Stops.

F11 – Custom Sound 2

Custom Sound 2 is a pre-programmed sound that you can call up at will by pressing F11

On then Off. It could anything from an ambient station sound to a conductor’s voice. It

will be the same sound each time you trigger it.

F12 – All/Random Stops

You can control whether the engine stops at all the pre-programmed stops taught to it

in Learn Mode or at Random stops along the route. To do this:

1. While the engine is running or while it’s stopped, doesn’t matter; press the F12 button

so it’s On. Once F12 is active you are now telling the engine to stop at Random stops

along the route. To make it stop at ALL stops along the route turn off F12

F13-F16 – Idle Sequence

Pressing F13, F14, F15, or F16 twice (toggling on then off) will trigger an Idle Sequence

if the engine is not moving. These vary from engine to engine and may include things

like checking the coal load, checking the water level, using the Alemite grease gun on the

drivers, etc. When triggered, these will run through the sequence that varies in duration.

NOTE: The engine must be sitting still in order to trigger these

F17 – Extended Start-Up

If your engine is shut down or you've just applied DCC power pressing F17 twice

(toggling it on then off) will start the Extended Start-Up

sounds. This is very similar to F3 except you will hear the crew talking back and forth

about getting the engine ready to run.

F18 – Extended Shut-Down

If your engine is already up and running you can play

the Extended Shut Down sounds by pressing F18 twice (toggling on then off). The

Extended Shut Down is very similar to F3 in that the engine will ultimately shut down,

but in the case of Extended Shut Down you will hear the crew talking back and forth

about how the engine ran, time schedules, etc.

F19 – Train Marker Train Marker is used on certain engines that carry marker or End

Of Train lighting. This is controlled by F19. When F19 is On the Marker light will be

On. If F19 is Off, the marker will be Off.

F20 – Local/Express or Alternate Mode Lighting

The Local/Express control is for engines that carry a local/express light (R-17 subway,

for example). Some engines do not carry this light or this feature. Alternatively, some

engines do carry a light that can be toggled by F20. Often times this will be a Beacon

light or a variable indicator light of some kind. Again, not all engines carry a light

controllable by F20.

RailKing PCC Electric Street Car w/ Proto-Sound® 3.0

F21 – One Shot Doppler

You can set your MTH PS3.0-equipped engine to simulate the actual Doppler Effect

sound a real engine makes as it passes you. To do this, press the F21 button once

(enable F21) and then listen as the engine makes that pitch shift that mimics the

Doppler Effect perfectly. Press the F21 button again (disable F21) to shut off the

Doppler Effect. With a little practice in timing and speed you can make this happen

right in front of you.

F22 – Coupler Slack

When an engine hooks up and pulls a train it has to take up the coupler slack. You can

play this sound by pressing F22 twice (toggling on then off). This feature works two

ways – While the engine is sitting still, press F22 twice to enable it. Then, when you

move the engine, it will play the Coupler Slack sound.

The second way is to simply force the sound while the engine is moving. To do this,

simply press F22 twice (toggling it on then off). The sound will play.

F23 – Coupler Close

To play the Coupler Close sound press the F23 button twice (toggling it on then off).

You can play this sound as you're coupling cars together to add realism.

F26 – Brake Sounds

Pressing the F26 button (enable F26) will disable the Brake Sounds for your engine. The

Brake Sounds occur when you reduce the speed of your engine rapidly. To enable the

Brake Sounds press the F26 button (disable F26). Brake Sounds are On by default.

F27 – Cab Chatter

Cab Chatter occurs when the engine is sitting at idle. There are various times when the

crew will talk to each other when the engine is sitting at idle. Pressing the F27 button

(enable F27) will disable the Cab Chatter. Pressing the F27 button again (disable F27)

will enable Cab Chatter. Cab Chatter is On by default.

F28 – Feature Reset

Resets Features to defaults.

F24 – Custom Sound 1

Functions exactly like Custom Sound 2 except Custom Sound 1 will play a different pre-

programed sound each time F24 is toggled On/Off.

RailKing PCC Electric Street Car w/ Proto-Sound® 3.0

*Many Subway and Trolley models do not have operating couplers.

Refer to pages 24-26 for CV Data and Function ID

FUNCTION CHART

F Key Description

F0 Head/Tail light

F1 Bell

F2 Horn

F3 Start-Up/Shut Down

F4 Station Announcement

F5 Lights (except head/tail)

F6 Master Volume

F7 Auto Mode

F8 Learn Mode

F9 Forward Signal

F10 Reverse Signal

F11 Custom Sound 2

F12 All/Random Stops

F13 Idle Sequence 4

F14 Idle Sequence 3

F15 Idle Sequence 2

F16 Idle Sequence 1

F17 Extended Start-Up

F18 Extended Shut-Down

F19 Train Marker

F20 Local/Express or

Alternate Mode Lighting

F21 One Shot Doppler

F22 Coupler Slack*

F23 Coupler Close*

F24 Custom Sound 1

F25 Engine Sounds

F26 Brake Sounds (On/Off)

F27 Cab Chatter (On/Off)

F28 Feature Reset

Page is loading ...

MTHTrains 30-5134-1 User manual

Brand: MTHTrains

Model: 30-5134-1

Type: User manual

This manual is also suitable for

Download PDF

report

MTHTrains 30-5134-1 User manual

This manual is also suitable for

MTHTrains 30-5134-1 User manual

Related papers

Other documents