Crown Omnia DP3 Owner's manual

Brand: Crown

Model: Omnia DP3

Type: Owner's manual

This manual is also suitable for

FMX30

International Radio & Electronics Corporat ion

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

CROWN/OMNIA

DP3

DIGITAL AUDIO PROCESSING

CARD

INSTALLATION &

OPERATION MANUAL

CROWN BROADCAST/IREC 25166 Leer Drive Elkhart, IN 46514

TEL: +1 (574) 262-8900 FAX: +1 (574) 262-5399

E-MAIL: [email protected]

www.crownbroadcast.com

revision 1.00

International Radio & Electronics Corporat ion

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

GREETINGS!

Welcome to the Crown DP3 Audio Processor, the first digital audio processor

designed exclusively for the Crown Broadcast transmitter line.

The DP3 applies the same advanced design philosophy as the entire Omnia

family, to yield performance and flexibility never before available as an internal

transmitter option.

The DP3, like all Omnia products, delivers crystal-clear highs, thundering bass

and amazing loudness, with none of that “digital grunge aftertaste!”

The DP3 is a fully digital system that is available as an upgrade to current Crown

transmitters, and as a new product option for either our industry standard FM

transmitter line, or our FMX digitally controlled transmitters.

DP3’s flexibility is built-into the design. Instead of keeping the processing

algorithms on a set of EPROM’s or proprietary potted modules, the system’s DSP

(Digital Signal Processing) resources are entirely configured through software

contained in the DP3 card.

Even fundamental rearrangements of the system architecture can be easily

accomplished in the field by using the web-browser based remote control

application, via ETHERNET connection.

International Radio & Electronics Corporat ion

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

iii

TABLE OF CONTENTS

Introduction and Contents………………………………………….. i-vii

Table of Contents………………………………………………… iii

Specifications……………………………………………………. vi

Warranty…………………………………………………………. vii

SECTION 1: Field Installation Instructions

1.2. FMA Transmitter……………………………………………. 1-2

1.3. FMX Transmitter……………………………………………. 1-8

SECTION 2: OMNIA DP-3 Operation – Crown FMA Transmitter.. 2-1

SECTION 3: OMNIA DP-3 Operation – FMX-DMS Transmitter

3.1. Initial Power-up Procedures………………………………….. 3-1

3.2. Controls and Display…………………………………………. 3-2

3.3. Operating the FMX…………………………………………… 3-4

3.4. Passwords…………………………………………………….. 3-4

3.5. Readings Function List………………………………………. 3-4

3.6. Settings Function List………………………………………… 3-6

3.7. Factory Settings………………………………………………. 3-7

3.8. Audio Monitor………………………………………………… 3-7

3.9. Fault Log……………………………………………………… 3-8

3.10. Power-up Procedure…………………………………………. 3-8

3.11. DP3 Processor Function List………………………………… 3-9

SECTION 4: DP-3 REMOTE Control Interface via Computer

ETHERNET Port

4.1. Preparatory Needs for ETHERNET connection……………… 4-1

4.2. Instructions for ETHERNET connection…………………….. 4-2

SECTION 5: APPENDICES

5.1. Network card configuration………………………………….. 5-1

5.2. Troubleshooting……………………………………………… 5-18

5.3. Guide for adjusting processing parameters of DP3………….. 5-20

International Radio & Electronics Corporat ion

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

WARNING -- This equipment generates, uses, and can radiate radio frequency

energy. If not installed and used in accordance with the instructions in this manual

it may cause interference to radio communications. It has been tested and found to

comply with the limits for a Class A computing device (pursuant to subpart J of

Part 15 FCC Rules), designed to provide reasonable protection against such

interference when operated in a commercial environment. Operation of this

equipment in a residential area is likely to cause interference, at which case, the

user, at his own expense, will be required to take whatever measures may be

required to correct the interference.

CANADA WARNING – This digital apparatus does not exceed the Class A

limits for radio noise emissions set out in the Radio Interference Regulations of

the Canadian Department of Communications. Le present appareil numerique

n'emet pas de bruits radioelectriques depassant les limits applicables aux

brouillage radioelectrique edicte par le ministere des Communications de Canada.

NOTICES

All versions, claims of compatibility, trademarks, etc. of hardware and software

products not made by Crown Broadcast, but mentioned in this manual or other

accompanying material, are informational only. Crown Broadcast makes no

endorsement of any particular product for any purpose, nor claims any

responsibility for its operation or the accuracy of the presentation.

Trademarks

Crown Broadcast, and the Crown Broadcast mark are trademarks of International

Radio and Electronics, Inc. (IREC). All other trademarks mentioned in this

manual are the property of their respective holders.

the right to make improvements or changes to the products described herein

(which may affect the product specifications) and to revise this manual as

required without notice.

Repair Procedures

You must contact Crown Broadcast for a Return Authorization number before

returning any products. Packages without proper authorization may be refused.

Write the RA number on the shipping label side of the returned package. Be sure

to adequately insure your shipment. Customers in North America can contact

Crown Broadcast customer support at +1 (866) 262-8917. All other customers

should contact their local dealer to verify the problem and then contact Crown

Broadcast Customer Service to arrange for repair.

International Radio & Electronics Corporat ion

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

Caution

The installation and servicing instructions presented in this manual are for use by

qualified installation and service personnel only. To avoid electric shock, do not

perform any servicing other than that contained in the operating instructions

unless you are qualified to do so. Refer all servicing to qualified personnel.

Warning

To reduce the risk of electrical shock, do not expose this product to rain or

moisture.

International Radio & Electronics Corporat ion

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

SPECIFICATIONS

All measurements referenced to 100% output. It is not possible to quantify the

specifications of the gain controlling functions of the AGC and limiter sections

due to the dynamic nature of the DP3 system under program conditions. To

properly evaluate these functions, there is only one known precise set of test gear

for that—your ears! Listen and judge carefully.

Audio performance *

• Frequency Response: ±0.2 dB, 50 Hz - 15 kHz

• System Distortion: 0.017% THD, flat or de-emphasized

• Signal-to-Noise Ratio: >80 dB, flat or de-emphasized

• Channel Separation: >85 dB, 10 Hz - 15 kHz

Analog I/O Section

• Left & Right Audio Inputs: 10 k ohms (or 600 ohms, configurable via on board jumpers) electronically balanced bridging

input, 20-bit analog-to-digital converter

• Maximum Input Level: +24 dBu

• Connector: XLR, female, EMI suppressed

• Discrete Left/Right Audio Outputs: 600 Ω load or greater, un-balanced, 18-bit digital-to-analog

converter, de-emphasized (50 or 75 µs via ETHERNET port configuration)

• Connector: Phono Jack

Digital I/O Section

• Configuration: Stereo AES/EBU ; automatic detection on Analog/Left input XLR.

• Input Sampling Rates: 32 kHz, 44.1 kHz, 48 kHz, sample rate converter provided

• Input Connector: XLR, female, balanced and floating

Composite I/O Section

• SCA / RBDS Subcarrier Input: BNC, unbalanced

• Impedance: 50 ohms

• Signal: 53 kHz subcarrier is summed into composite output.

• Software controls: Input level attenuation control in ETHERNET port configuration

Pilot Output

• Software control: Output level

Composite Output

• Composite Output Level: 0 – 6 Volts p-p, software adjustable (feeds exciter board).

Computer Interface

• Configuration: Ethernet 10/100.

• Communications: web browser

• Software-controlled (through the remote application).

Dimensions & Weight

• 5.5” x 10.75” plug-in card (14 x 27 cm)

In the interests of product improvement, Crown Broadcast reserves the right to change, add or modify any

specification.

* Test performance measured at the Audio Monitor Jacks on the rear panel

International Radio & Electronics Corporat ion

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

vii

Warranty

Crown Broadcast, IREC warrants its broadcast products to the ORIGINAL

PURCHASER of a NEW Crown Broadcast product, for a period of three

(3) years after shipment from Crown Broadcast. All products are

warranted to be free of defects in materials and workmanship and meet or

exceed all specifications published by Crown Broadcast. Product

nameplate with serial number must be intact and not altered in any way.

This warranty is non - transferable. This warranty in its entirety is the only

warranty offered by Crown Broadcast. No other warranties, expressed or

implied, will be enforceable.

Exclusions

Crown Broadcast will not warranty the product due to misuse, accident,

neglect and improper installation or operation. Proper installation includes

A/C line surge suppression, lightning protection and proper grounding of

the entire transmitter, and any other recommendations designated in the

instruction manual. This warranty does not extend to any other products

other than those designed and manufactured by Crown Broadcast. This

warranty does not cover any damage to any accessory such as loads,

transmission line or antennas resulting from the use or failure of a Crown

Broadcast transmitter. Warranty does not cover any loss of revenue

resulting from any failure of a Crown Broadcast product, act of God, or

national disaster.

Procedure for Obtaining Warranty Service

Crown Broadcast will repair or replace, at their discretion, any product

failure as a result of normal intended use. Warranty repair can only be

performed at our plant facility in Elkhart, Indiana USA or at a factory

authorized service depot. Expenses in remedying the defect will be borne

by Crown Broadcast, including two – way ground transportation cost within

the continental United States.

Prior to returning any product or component to Crown Broadcast for

warranty work or repair a Return Authorization (RA) number must be

obtained from the Crown Broadcast Customer Service Department.

Product must be returned in the original factory pack or equivalent.

Original factory pack materials may be obtained at a nominal charge by

contacting Crown Broadcast Customer Service. Resolution of the

defective product will be made within a reasonable time from the date of

receipt of the defective product.

International Radio & Electronics Corporat ion

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

viii

Warranty Alterations

No person has the authority to enlarge, amend or modify this warranty, in

whole or in part. This warranty is not extended by the length of time for

which the owner was deprived the use of the product. Repairs and

replacement parts that are provided under the terms of this warranty shall

carry only the unexpired portion of the warranty.

Product Design Changes

Crown Broadcast reserves the right to change the design and

manufacture of any product at any time without notice and without any

obligation to make corresponding changes in products previously

manufactured.

Legal Remedies of Purchaser

This written warranty is given in lieu of any oral or implied warranties not

contained herein. Crown disclaims all implied warranties including any

warranties of merchantability or fitness for a particular purpose.

Crown Broadcast

25166 Leer Drive

Elkhart, Indiana 46514 - 5425

Phone 574 – 262 - 8900

Fax 574 – 262 – 5399

www.crownbroadcast.com

International Radio & Electronics Corporation

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

1-1

1 SECTION 1: DP-3 FIELD INSTALLATION

The Crown-Omnia DP3 Processor Card can be ordered as part of a new Crown

Broadcast transmitter, or it can be ordered as an upgrade for installation in a currently

owned Crown transmitter. In the first case we worry about installing the card. In the

second case you do.

Still, do not worry much. The DP-3 has been designed for straightforward, even easy,

installation into all Crown transmitters. “Easy installation” can be slippery terminology

when applied to complex technical items, but we think we can back it up here.

If you are upgrading a transmitter you already own, first of all let us congratulate you on

your decision to add the state-of-the-art audio processing of the Crown-Omnia DP-3 to

your broadcasts. Although we have been pleased over the years with the response we

have gotten from users of our basic processor design, we are very excited about the

addition of Omnia processing power to Crown transmitters.

The DP-3 adds many new possibilities to the sound of your radio. From Omnia presets

to your own personally tweaked signature audio, your broadcasts will never sound better.

PC control of the processing elements, along with programmable addresses for your

personal presets, give flexible new processing tools to every kind of user.

And even though we believe the DP-3 installation will be crystal clear and classic in its

simplicity, please take a few minutes to read through this chapter before proceeding with

the installation.

1.1 UNPACKING – VERIFYING PARTS

By now, you’ve gotten the DP-3 processor card out of its shipping pack. Check for

damage to report to your dealer. Be sure to inspect the DP-3 and shipping carton for any

shipping damage, which must be reported to your carrier for any claims.

The DP-3 shipping box includes the following items:

• DP-3 processor card

• DP-3 Operating Manual- which you are reading now.

• Warranty Registration Card (fill it out and return it)

• ETHERNET Cable

International Radio & Electronics Corporation

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

1-2

1.2 CROWN-OMNIA DP3 INSTALLATION INSTRUCTIONS – FMA

TRANSMITTER

FIG 1

• Remove Top Cover and keep hardware to be used when finished with installation.

• Remove the eight screws holding item 1 and item 2 in the unit as shown in FIG 1.

• Keep all hardware, as it will be used in the DP3 PWA installation.

• Remove Stereo Generator PWA (1) as shown in FIG 2.

• Remove the Audio Processor PWA (2) as shown in FIG 2.

International Radio & Electronics Corporation

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

1-3

FIG 2

• Remove the DD Hole Plug from the Back Panel “Receiver In” hole.

• Remove the White retaining clip as indicated in FIG 3 and set aside for later use.

• Feed the Omnia Ethernet cable through the “Receiver In” hole as shown in FIG 4.

FIG 3 FIG 4

• Feed the Omnia Ethernet cable completely through and put into DD hole opening as

shown in FIG 6.

NOTE: Locking tab on cable bulkhead should point upwards as shown in FIG 5.

International Radio & Electronics Corporation

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

1-4

FIG 5 FIG 6

• Slide the white-retaining clip onto the cable and lock into place as shown in FIG 7 & 8.

FIG 7 FIG 8

• Orient the Omnia Ethernet cable as shown in FIG 9.

• Hold the Crown/Omnia PWA by the protective shield and begin the installation as

shown in FIG 9.

FIG 9

International Radio & Electronics Corporation

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

1-5

• Align the Crown/Omnia PWA with the Motherboard headers and press into place as

shown in FIG 10, 11, 12, 13, 14 & 15.

FIG 10 FIG 11

FIG 12 FIG 13

FIG 14 FIG 15

• Finish the routing of the Omnia Ethernet cable as shown in FIG 16, 17 & 18 and plug

into the port as shown in FIG 17.

International Radio & Electronics Corporation

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

1-6

FIG 16 FIG 17

• Using the 6-32 hardware from the old PWA removal, fasten the new PWA to the

Motherboard as shown in FIG 18.

FIG 18

• Torque the PWA hardware @ 14 inch-Lbs.

• Check and set the Audio Input Impedance High/Low jumper settings on the

Crown/Omnia PWA to the value needed.

• These jumpers can found as shown in FIG 19 & 20.

International Radio & Electronics Corporation

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

1-7

FIG 19 FIG 20

• Plug your Cat 5 cable into the Ethernet port as shown in FIG 21.

FIG 21

• Reinstall the Top Cover and use the 6-32 hardware that was put aside when starting

this installation process.

• Torque the hardware @ 14 inch-Lbs.

• The unit is now ready for operation.

• Follow the manual for proper start-up procedures.

International Radio & Electronics Corporation

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

1-8

1.3 CROWN-OMNIA DP3 INSTALLATION INSTRUCTIONS – FMX

TRANSMITTER

FIG 1

• Remove the hardware fastening the Top Cover to the Unit chassis as shown in FIG 1

and remove the cover.

NOTE: The hardware set consists of a # 6 lock-washer, a #6 flat washer, and a 6-32

screw or a 6-32 SEMS internal tooth lock-washer and #6 Flat washer.

• Save this hardware. It will be reused after PWA installation is completed.

FIG 2

International Radio & Electronics Corporation

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

1-9

• Remove the 6-32 hardware fastening the Audio Low Pass Filter and the Audio

Processor PWA’s to the unit.

• Put this hardware aside, to use later in the PWA installation process.

• Wearing a static strap, remove the two PWA’s as shown in FIG 2.

• If the AES/EBU function is not needed, go to the Omnia Ethernet cable installation

procedure below.

• AES/EBU jumper block installation prep if needed -

• Using needle nose pliers, lightly pull the resistors R1, R2 and R3 towards one another

as shown in FIG 3 & FIG 4.

NOTE: Be careful not to break the resistors while bending these leads.

FIG 3 FIG 4

• Install the AES/EBU jumper block by snapping the feet onto the leads of the resistors

as shown in FIG 5 & FIG 6.

NOTE: Be sure the orientation of the jumper is as shown in FIG 5 & FIG 6.

FIG 5 FIG 6

• Solder the legs of the jumper onto the resistor leads for a proper connection

International Radio & Electronics Corporation

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

1-10

• Remove the DD Hole Plug from the Back Panel “Receiver In” hole.

• Remove the White retaining clip as indicated in FIG 7 and set aside for later use.

• Feed the Omnia Ethernet cable through the “Receiver In” hole as shown in FIG 8.

FIG 7 FIG 8

• Feed the Omnia Ethernet cable completely through and put into DD hole opening as

shown in FIG 10.

NOTE: Locking tab on cable bulkhead should point upwards as shown in FIG 9.

FIG 9 FIG 10

• Slide the white-retaining clip onto cable and lock into place as shown in FIG 11 & 12.

FIG 11 FIG 12

International Radio & Electronics Corporation

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

1-11

• Orient the Omnia Ethernet cable as shown in FIG 13.

• Hold the Crown/Omnia PWA by the protective shield and begin the installation as

shown in FIG 13.

FIG 13

• Align the Crown/Omnia PWA with the Motherboard headers and press into place as

shown in FIG 14, 15, 16, 17, 18 & 19.

FIG 14 FIG 15

FIG 16 FIG 17

International Radio & Electronics Corporation

25166 Leer Drive Elkhart, Indiana 46514 • 574 –262–8900 • www.irec1.com

1-12

FIG 18 FIG 19

• Finish the routing of the Omnia Ethernet cable as shown in FIG 20, 21 & 22 and plug

into the port as shown in FIG 21.

FIG 20 FIG 21

• Using the 6-32 hardware from the old PWA removal, fasten the new PWA to the

Motherboard as shown in FIG 22.

FIG 22

Page is loading ...

Crown Omnia DP3 Owner's manual

Brand: Crown

Model: Omnia DP3

Type: Owner's manual

This manual is also suitable for

FMX30

Download PDF

report

Crown Omnia DP3 Owner's manual

This manual is also suitable for

Crown Omnia DP3 Owner's manual

Related papers

Other documents