Faux EZ FEZ 103 User guide

Brand
Faux EZ
Model
FEZ 103
Type
User guide

This manual is also suitable for

Faux EZ FEZ 103 Below you will find brief product information for Faux EZ FEZ 103. The Faux EZ FEZ 103 is a revolutionary product that allows you to transform the look of your cabinets, furniture, and other surfaces without the need for sanding or priming. With Faux EZ FEZ 103, you can achieve a professional-looking finish that will last for years to come.

Here are just a few of the benefits of using Faux EZ FEZ 103:

  • Easy to use - Faux EZ FEZ 103 is a water-based product that is easy to apply. Simply brush on the liquid base coat and then spray on the aerosol top coat.

Faux EZ FEZ 103 Below you will find brief product information for Faux EZ FEZ 103. The Faux EZ FEZ 103 is a revolutionary product that allows you to transform the look of your cabinets, furniture, and other surfaces without the need for sanding or priming. With Faux EZ FEZ 103, you can achieve a professional-looking finish that will last for years to come.

Here are just a few of the benefits of using Faux EZ FEZ 103:

  • Easy to use - Faux EZ FEZ 103 is a water-based product that is easy to apply. Simply brush on the liquid base coat and then spray on the aerosol top coat.
FAUX EZ™ (Original)
Directions for Use
May be used on:
Any existing soundly adhered, nearly white interior primed/sealed surface such
as painted wood, metal and vinyl coated cabinets etc. in good condition.
Product Coverage:
Step One liquid brush-on base coat:
8oz. liquid base covers about 20 square feet.
Step Two Aerosol
16 oz. aerosol covers about 20 square feet for light colors like oak or pine. Use
addition Step Two for darker colors such as Walnut or Mahogany.
Things you will also need:
1. Krud Kutter or TSP
2. Blue tape and paper
3. Cleaning sponge
4. Sanding sponge
Also see video on Directions for Use.
Surface Preparation:
DO NOT USE STEEL WOOL!
1. Sand rough surfaces until smooth. If surface is already smooth, no sanding
is required but surface must be cleaned with Krud Kutter or TSP and rinsed
well.
2. Fill holes and caulk as needed and sand smooth again.
4. Tape off adjoining areas within spraying distance, (about 4 feet) and cover
floors and ceiling.
Applying FAUX EZ™:
1. Stir contents of liquid ‘Step 1’ thoroughly.
2. Apply ‘Step 1’ using your chip brush, leaving streak
marks on the finish. Apply very sparingly. Work very quickly.
Don’t try to make it cover solid. You want streaks to look like grain,
so be sure to brush the same direction that the grain of real wood
would go. If you have a drip or run, brush it out immediately!
Excessive brushing is not recommended.
Remember that real wood is not perfect. That’s what makes it
beautiful!
3. Allow 30 minutes for drying at normal temperature and humidity.
Remember that FAUX EZ™ is water-based and may take longer
dry time in high humidity.
4. Repeat the application of ‘Step 1’ and let dry for 30 minutes or
more.
5. Shake Step 2 aerosol for at least 1 minute.
6. Hold can upside down and spray onto masking paper to clear
nozzle.
7. Holding can upright at a slight angle spray onto masking paper to
get used to spray pattern. Put can into motion before pressing
release tip. Practice a little bit.
8. Spray with a steady motion. Make only two passes (back and
forth).
9. Repeat spray application for deeper color tones.
10.For richer depth of color, spray more around the edges.
11.You can also see in the video how to enhance the appearance of
panels in doors.
12. Clean up equipment and spills immediately with soap and water.
Caring for Faux EZ™ Products
1. For extra protection Faux EZ™ Products may be top coated with a clear
water-based polyurethane.
2. Clean finish with warm soapy water and a soft sponge. Do not use strong
detergents or bathroom type cleaners.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Faux EZ FEZ 103 User guide

Brand
Faux EZ
Model
FEZ 103
Type
User guide
This manual is also suitable for

Faux EZ FEZ 103 Below you will find brief product information for Faux EZ FEZ 103. The Faux EZ FEZ 103 is a revolutionary product that allows you to transform the look of your cabinets, furniture, and other surfaces without the need for sanding or priming. With Faux EZ FEZ 103, you can achieve a professional-looking finish that will last for years to come.

Here are just a few of the benefits of using Faux EZ FEZ 103:

  • Easy to use - Faux EZ FEZ 103 is a water-based product that is easy to apply. Simply brush on the liquid base coat and then spray on the aerosol top coat.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents