Dynex DX-M1113 User manual

Brand: Dynex

Model: DX-M1113

Category: Microphones

Type: User manual

This manual is also suitable for

DX-M1113 - Hands-Free Wireless Microphone

Dynex DX-M1113 - Hands-Free Wireless Microphone

The Dynex DX-M1113 Hands-Free Wireless Microphone provides high-quality audio transmission for a variety of applications. With its advanced features and user-friendly design, this microphone is perfect for karaoke, public speaking, presentations, and more.

Here are some of the key capabilities of the Dynex DX-M1113 Hands-Free Wireless Microphone:

High-frequency and mid-frequency narrow band filters to reduce interference from stray signals
Built-in headset antenna for reliable and convenient wireless operation
Quartz crystal oscillating circuits that ensure a steady frequency for clear and consistent audio

Dynex DX-M1113 - Hands-Free Wireless Microphone

Here are some of the key capabilities of the Dynex DX-M1113 Hands-Free Wireless Microphone:

High-frequency and mid-frequency narrow band filters to reduce interference from stray signals
Built-in headset antenna for reliable and convenient wireless operation
Quartz crystal oscillating circuits that ensure a steady frequency for clear and consistent audio

USER GUIDE

GUIDE DE L’UTILISATEUR • GUÍA DEL USUARIO

Dynex Hands-Free Wireless

Microphone

Microphone sans fil mains libres de

Dynex

Micrófono Inalámbrico de Manos

Libres de Dynex

DX-M1113

DX-M1113.fm Page 1 Tuesday, September 19, 2006 7:07 AM

Contents

Dynex DX-M1113 Hands-Free

Wireless Microphone

Contents

Important safety instructions ...................................2

Wireless microphone components ............................3

Setting up your wireless microphone .......................6

Using your wireless microphone ...............................7

Troubleshooting .......................................................8

Specifications ...........................................................9

Legal notice ............................................................11

Français.......................................17

Español .......................................33

Important safety instructions

Location

• Do not use your receiver or transmitter in an area with a

high magnetic field.

• Make sure that the receiver is at least 10 feet (3 meters)

above the floor and 10 feet (3 meters) from surrounding

walls.

• Do not place the receiver or transmitter in direct sunlight.

Do not expose the receiver or transmitter to rain or

moisture.

Repairs

Do not try to repair your wireless microphone yourself. Opening the case

could expose you to high electrical voltage. Refer all service to qualified

service personnel.

DX-M1113.fm Page 2 Tuesday, September 19, 2006 7:07 AM

Wireless microphone components

Handling

• Do not drop the receiver or transmitter.

• Do not set anything on top of the receiver.

Wireless microphone components

Package contents

You wireless microphone comes with:

• Headset

•Transmitter

•Audio cable

• Receiver

• Volume adjustment tool

• Two AA batteries

• One 9 V battery

•User guide

You wireless microphone features:

• High-frequency and mid-frequency narrow band filters to

reduce interference from stray signals

• Built-in headset antenna

• Quartz crystal oscillating circuits that insures a steady

frequency

• Audio compression and expansion technology that provide

rich sound at low volume

DX-M1113.fm Page 3 Tuesday, September 19, 2006 7:07 AM

Wireless microphone components

Receiver

Component Description

1 Antenna Receives RF signals from the transmitter. Fully extend the

antenna for the best reception.

2 RF indicator Lights when receiving RF signals from the transmitter.

3 OFF ON Turns the receiver on and off.

4 POWER indicator Lights when the receiver is turned on.

5 AUDIO OUT jack Connect an external amplifier to this jack.

6Battery

compartment

Insert two AA batteries into this compartment.

ROF

DX-M1113.fm Page 4 Tuesday, September 19, 2006 7:07 AM

Wireless microphone components

Transmitter

Volume adjustment tool

Component Description

1 Power switch Turns the transmitter on and off.

2 Power indicator Lights when the transmitter is turned on.

3 Volume control Turn the volume control with the volume adjustment tool

to adjust the volume if you experience signal interference

from other devices.

4 AF input Plug the headset into this jack.

DX-M1113.fm Page 5 Tuesday, September 19, 2006 7:07 AM

Setting up your wireless microphone

Setting up your wireless

microphone

The following illustration shows two basic ways to connect your receiver

to an amplifier.

Note: When you install the receiver, make sure that it is at

least 10 feet (3 meters) off the floor and at least 10 feet (3

meters) away from surrounding walls.

To set up the receiver:

1 Place the receiver on a flat, stable surface.

2 Fully extend the antenna, and make sure it is perpendicular

to the receiver.

3 Open the battery compartment, install two AA batteries

into the battery compartment, then close the

compartment. Make sure that the + and – symbols on the

batteries align with the + and – symbols inside the battery

compartment.

4 Plug one end of the audio cable into the AUDIO OUT jack on

the receiver.

Audio mixer

Receiver

Amplifier

Speaker

Karaoke amplifier

Speaker

DX-M1113.fm Page 6 Tuesday, September 19, 2006 7:07 AM

Using your wireless microphone

5 Plug the other end of the audio cable into the MIX IN or

AUX IN on an external amplifier.

6 Slide the power switch to the ON position. The POWER

indicator lights.

To install the transmitter battery:

1 Slide the battery compartment cover to open the battery

compartment.

2 Insert the 9V battery into the battery compartment. Make

sure that the + and – symbols on the battery align with

the + and – symbols inside the battery compartment.

3 Slide the cover to close the compartment.

Using your wireless microphone

Note: You can use your wireless microphone within a range of

164 feet (50 meters) of the receiver. The ideal range is 82 feet

(25 meters).

To use your wireless microphone:

1 Turn on the receiver.

2 Plug the headset into the AF input jack on the transmitter.

3 Place the headset on your head.

4 Turn on the transmitter.

5 If you experience interference from nearby devices, use the

volume adjustment tool to adjust the volume.

DX-M1113.fm Page 7 Tuesday, September 19, 2006 7:07 AM

Troubleshooting

Caution: Do not open the open the receiver or transmitter

cases. There are no user serviceable parts inside.

Symptom Possible solution

Receiver is turned on, but POWER

indicator does not light.

• Make sure that the batteries are installed

correctly. You must match the + and –

symbols on the batteries with the + and –

symbols in the battery compartment.

• Make sure that the batteries have a charge.

Change the batteries, if necessary.

The RF indicator lights when

speaking into the headset, but

there is no sound.

• Make sure that the volume control is not

set too low.

• Make sure that the audio cable is

connected securely to the receiver and

amplifier.

The signal range is too small. • Make sure that the antenna is fully

extended.

• Make sure that the batteries are installed

correctly. You must match the + and –

symbols on the batteries with the + and –

symbols in the battery compartment.

• Make sure that the batteries have a charge.

Change the batteries, if necessary.

• Make sure that the receiver or transmitter

are not located within a magnetic field.

DX-M1113.fm Page 8 Tuesday, September 19, 2006 7:07 AM

Specifications

Transmitter

Sound quality is poor. • Make sure that the batteries are installed

correctly. You must match the + and –

symbols on the batteries with the + and –

symbols in the battery compartment.

• Make sure that the batteries have a charge.

Change the batteries, if necessary.

• Make sure that no other devices in the area

are operating on the same frequency as

your wireless microphone. Devices using

the same frequency should be at least 328

feet (100 meters) apart.

Carrier Frequency VHF 170 to 270 MHz

Frequency stability < ± 30 PPM

Frequency response 50 Hz to 15 KHz ± 3 dB

Dynamic range > 90dB

Total harmonic distortion < 0.5%

Audio output level Separate type: 0 to ± 400 mV

Mix type: 0 to ± 200 mV

RF power output 30 mW

Current loss 60 mA

Range 164 ft. (50 m) (max.)

Pickup Dynamic or condenser

Battery 9 V

Symptom Possible solution

DX-M1113.fm Page 9 Tuesday, September 19, 2006 7:07 AM

Specifications

Receiver

Transmitter power 8.5 mW

Modulation type FM

Maximum deviation ± 25 KHz

Spurious emission > 40 dB (with carrier)

Battery life 6 to 8 hours

Sensitivity 6 uV @ sinad=12dB

Spurious rejection

≥ 85 dB (typical)

Image rejection > 75 dB (typical)

SNR > 90 dB

AF output 0 to 300 mV

Receiving channel 1 channel

Power DC 3 V

Power consumption 170 mW

De-emphasis 50 uS

Border on channel rejection >80dB

DX-M1113.fm Page 10 Tuesday, September 19, 2006 7:07 AM

Legal notice

FCC statement

This device complies with Part 74 of the FCC Rules. Operation is subject to

the following conditions:

• This device may not cause harmful interference; and

• This device must accept any interference received,

including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly

approved by the party responsible for compliance could void

the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will

not occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

DX-M1113.fm Page 11 Tuesday, September 19, 2006 7:07 AM

Legal notice

Canadian Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise

emissions from digital apparatus set out in the Radio Interference

Regulations of the Canadian Department of Communications.

Le present appareil numerique n'emet pas de bruits radioelectriques

depassant les limites applicables aux appareils numeriques de la class B

prescrites dans le Reglement sur le brouillage radioelectrique edicte par

le ministere des Communications du Canada.

Enterprise Services, Inc. Other brands and product names are trademarks

or registered trademarks of their respective holders. Specifications and

features are subject to change without notice or obligation.

DX-M1113.fm Page 12 Tuesday, September 19, 2006 7:07 AM

Warranty

1-year limited warranty

Dynex Products (“Dynex”) warrants to you, the original purchaser of this

new DX-M1113 (“Product”), that the Product shall be free of defects in

the original manufacture of the material or workmanship for a period of

one (1) year from the date of your purchase of the Product (“Warranty

Period”). This Product must be purchased from an authorized dealer of

Dynex brand products and packaged with this warranty statement. This

warranty does not cover refurbished Product. If you notify Dynex during

the Warranty Period of a defect covered by this warranty that requires

service, terms of this warranty apply.

How long does the coverage last?

The Warranty Period lasts for one year (365 days) from the date you

purchased the Product. The purchase date is printed on the receipt you

received with the product.

What does this warranty cover?

During the Warranty Period, if the original manufacture of the material or

workmanship of the Product is determined to be defective by an

authorized Dynex repair center or store personnel, Dynex will (at its sole

option): (1) repair the Product with new or rebuilt parts; or (2) replace the

Product at no charge with new or rebuilt comparable products or parts.

Products and parts replaced under this warranty become the property of

Dynex and are not returned to you. If service of Products and parts are

required after the Warranty Period expires, you must pay all labor and

parts charges. This warranty lasts as long as you own your Dynex Product

during the Warranty Period. Warranty coverage terminates if you sell or

otherwise transfer the Product.

DX-M1113.fm Page 13 Tuesday, September 19, 2006 7:07 AM

Warranty

How to obtain warranty service?

If you purchased the Product at a retail store location, take your original

receipt and the Product to the store you purchased it from. Make sure that

you place the Product in its original packaging or packaging that provides

the same amount of protection as the original packaging. If you

purchased the Product from an online web site, mail your original receipt

and the Product to the address listed on the web site. Make sure that you

put the Product in its original packaging or packaging that provides the

same amount of protection as the original packaging.

Where is the warranty valid?

This warranty is valid only to the original purchaser of the Product in the

United States and Canada.

What does the warranty not cover?

This warranty does not cover:

• Customer instruction

•Installation

•Set up adjustments

• Cosmetic damage

• Damage due to acts of God, such as lightning strikes

• Accident

•Misuse

•Abuse

•Negligence

•Commercial use

• Modification of any part of the Product

This warranty also does not cover:

• Damage due to incorrect operation or maintenance

• Connection to an incorrect voltage supply

• Attempted repair by anyone other than a facility authorized by

Dynex to service the Product

• Products sold as is or with all faults

• Consumables, such as fuses or batteries

• Products where the factory applied serial number has been

altered or removed

DX-M1113.fm Page 14 Tuesday, September 19, 2006 7:07 AM

Warranty

REPAIR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR

EXCLUSIVE REMEDY. DYNEX SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR

CONSEQUENTIAL DAMAGES FOR THE BREACH OF ANY EXPRESS OR IMPLIED

WARRANTY ON THIS PRODUCT, INCLUDING, BUT NOT LIMITED TO, LOST

DATA, LOSS OF USE OF YOUR PRODUCT, LOST BUSINESS OR LOST PROFITS.

DYNEX PRODUCTS MAKES NO OTHER EXPRESS WARRANTIES WITH RESPECT

TO THE PRODUCT, ALL EXPRESS AND IMPLIED WARRANTIES FOR THE

PRODUCT, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF

AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET

FORTH ABOVE AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED,

WILL APPLY AFTER THE WARRANTY PERIOD. SOME STATES, PROVINCES

AND JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN

IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO

YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY

ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR

PROVINCE TO PROVINCE.

DX-M1113.fm Page 15 Tuesday, September 19, 2006 7:07 AM

Warranty

DX-M1113.fm Page 16 Tuesday, September 19, 2006 7:07 AM

Page is loading ...

Avis juridique

DX-M1113.fm Page 28 Tuesday, September 19, 2006 7:07 AM

Page is loading ...

Avis juridique

DX-M1113.fm Page 32 Tuesday, September 19, 2006 7:07 AM

Page is loading ...

Avisos legales

DX-M1113.fm Page 44 Tuesday, September 19, 2006 7:07 AM

Page is loading ...

Avisos legales

DX-M1113.fm Page 48 Tuesday, September 19, 2006 7:07 AM

Page is loading ...

Dynex DX-M1113 User manual

Brand: Dynex

Model: DX-M1113

Category: Microphones

Type: User manual

This manual is also suitable for

DX-M1113 - Hands-Free Wireless Microphone

Dynex DX-M1113 - Hands-Free Wireless Microphone

Here are some of the key capabilities of the Dynex DX-M1113 Hands-Free Wireless Microphone:

High-frequency and mid-frequency narrow band filters to reduce interference from stray signals
Built-in headset antenna for reliable and convenient wireless operation
Quartz crystal oscillating circuits that ensure a steady frequency for clear and consistent audio

Download PDF

report