GE 23, 25 User manual

GEAppliances.com
Refrigerators
Side by Side
200D2600P036      49-60343     10-04 JR
La section française commence à la page 40
La sección en español empieza en la página 74
Safety Instructions  . . . . . . . . . . .2–4
Operating Instructions
Additional Features  . . . . . . . . . . . .10
Automatic Icemaker  . . . . . . . . . . .12
Care and Cleaning . . . . . . . . . .14, 15
Crispers and Pans  . . . . . . . . . . . . .11
Ice and Water Dispenser  . . . . .13, 14
Refrigerator Doors . . . . . . . . . .10, 11
Replacing the Light Bulbs . . . . . . .16
Shelves and Bins  . . . . . . . . . . . . .8, 9
Temperature Controls . . . . . . . . . . .5
TurboCool
™
 . . . . . . . . . . . . . . . . . . .6
Water Filter  . . . . . . . . . . . . . . . . . . .7
Installation Instructions
Installing the Refrigerator  . . . .22–25
Preparing to Install 
the Refrigerator  . . . . . . . . . . . .17–19
Removing and 
Replacing Doors  . . . . . . . . . . .19–21
Water Line Installation  . . . . . .26–28
Troubleshooting Tips  . . . . . . .30–32
Normal Operating Sounds  . . . . . .29
Consumer Support
Consumer Support  . . . . .Back Cover
Performance Data Sheet  . . . . . . . .36
Product Registration  . . . . . . . .33, 34
State of California Water 
Treatment Device Certificate . . . . .37
Warranty (Canadian) . . . . . . . . . . .38
Warranty (U.S.)  . . . . . . . . . . . . . . .39
Réfrigérateurs
Côte à Côte
Refrigeradores
Lado a Lado
Models 23 and 25
Write the model and serial numbers here:
# ________________________________
# ________________________________
Find these numbers on a label inside 
the refrigerator compartment at the 
top on the right side.
Owner’s Manual 
and Installation
Manuel d’utilisation 
et d’installation
Manual del propietario 
e instalación

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

2

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■ This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

■

■ Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

■

■ Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.

■

■ Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

■

■ In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating

element located on the bottom of the icemaker.

Do not place fingers or hands on the automatic

icemaking mechanism while the refrigerator

is plugged in.

■

■ Keep fingers out of the “pinch point” areas;

clearances between the doors and between

the doors and cabinet are necessarily small.

Be careful closing doors when children are

in the area.

■

■ Unplug the refrigerator before cleaning and

making repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

■

■ Setting either or both controls to 0 (off) does not

remove power to the light circuit.

■

■ Do not refreeze frozen foods which have

thawed completely.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

GEAppliances.com

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are

still dangerous…even if they will sit for “just a few

days.” If you are getting rid of your old refrigerator,

please follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old Refrigerator

or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may

not easily climb inside.

CFC Disposal

Your old refrigerator may have a cooling system

that used CFCs (chlorofluorocarbons). CFCs are

believed to harm stratospheric ozone.

If you are throwing away your old refrigerator, make

sure the CFC refrigerant is removed for proper

disposal by a qualified servicer. If you intentionally

release this CFC refrigerant, you can be subject to

fines and imprisonment under provisions of

environmental legislation.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use

of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

3

4

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall outlet

to minimize the possibility of electric shock hazard

from this appliance.

Have the wall outlet and circuit checked by

a qualified electrician to make sure the outlet

is properly grounded.

If the outlet is a standard 2-prong outlet, it is

your personal responsibility and obligation to

have it replaced with a properly grounded

3-prong wall outlet.

The refrigerator should always be plugged into

its own individual electrical outlet which has

a voltage rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on

the power cord. Always grip plug firmly and pull

straight out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

USE OF ADAPTER PLUGS (Adapter plugs not permitted in Canada)

Because of potential safety hazards under certain conditions, we strongly recommend against

the use of an adapter plug.

However, if you must use an adapter, where local

codes permit, a temporary connection may be made

to a properly grounded 2-prong wall outlet by use

of a UL-listed adapter available at most local

hardware stores.

The larger slot in the adapter must be aligned with

the larger slot in the wall outlet to provide proper

polarity in the connection of the power cord.

When disconnecting the power cord from the

adapter, always hold the adapter in place with one

hand while pulling the power cord plug with the

other hand. If this is not done, the adapter ground

terminal is very likely to break with repeated use.

If the adapter ground terminal breaks, DO NOT

USE the refrigerator until a proper ground has

been established.

Attaching the adapter ground terminal to a wall outlet

cover screw does not ground the appliance unless the

cover screw is metal, and not insulated, and the wall

outlet is grounded through the house wiring. You should

have the circuit checked by a qualified electrician to

make sure the outlet is properly grounded.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

5

About the temperature controls. GEAppliances.com

WARMERCOLDER

ADJUST REFRIGERATOR TEMP

9 IS COLDEST

WARMERCOLDER

ADJUST FREEZER TEMP

9 IS COLDEST

The temperature controls are preset in the factory at 5 for both

the refrigerator and freezer compartments. Allow 24 hours for the

temperature to stabilize to the preset recommended settings.

Several adjustments may be required. Each time you adjust

controls, allow 24 hours for the refrigerator to reach the setting

you have selected.

Setting either or both controls to 0 stops cooling in both the freezer

and refrigerator compartments, but does not shut off electrical power

to the refrigerator.

Control settings will vary based on personal preferences, usage and

operating conditions and may require more than one adjustment.

NOTE: The refrigerator is shipped with protective film covering the

temperature controls. If this film was not removed during installation,

remove it now.

The Performance Air Flow System is designed to maximize temperature control in the refrigerator and

freezer compartments. This unique special feature consists of the Air Tower along the back wall of the

refrigerator and the Air Tunnel on the bottom portion of the freezer rear wall. Placing food in front of the

louvers on these components will not affect performance. Although the Air Tower and the Air Tunnel can

be removed, doing so will affect temperature performance. (For removal instructions, on-line, 24 hours a

day, contact us at GEAppliances.com or call 800.GE.CARES. In Canada, contact us at geappliances.ca or

call 1.800.361.3400.)

Performance Air Flow System

6

About TurboCool.

™

(on some models)

How it Works

TurboCool rapidly cools the refrigerator

compartment in order to more quickly

cool foods. Use TurboCool when adding a

large amount of food to the refrigerator

compartment, putting away foods after they

have been sitting out at room temperature

or when putting away warm leftovers. It can

also be used if the refrigerator has been

without power for an extended period.

Once activated, the compressor will turn on

immediately and the fans will cycle on and

off at high speed as needed for eight hours.

The compressor will continue to run until

the refrigerator compartment cools to

approximately 34°F (1°C), then it will cycle

on and off to maintain this setting. After 8

hours, or if TurboCool is pressed again, the

refrigerator compartment will return to

the original setting.

How to Use

Press TurboCool. The refrigerator

temperature display will show 9 (the coldest

setting).

After TurboCool is complete, the

refrigerator compartment will return

to the original setting.

NOTES: The refrigerator temperature

cannot be changed during

TurboCool.

The freezer temperature is not

affected during TurboCool.

When opening the refrigerator

door during TurboCool, the fans

will continue to run if they have

cycled on.

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

7

About the water filter. (on some models) GEAppliances.com

On some models

Water Filter Cartridge

The water filter cartridge is located in the

back upper right corner of the refrigerator

compartment.

When to Replace the Filter

There is a replacement indicator light for

the water filter cartridge on the dispenser.

This light will turn orange to tell you that

you need to replace the filter soon.

The filter cartridge should be replaced

when the replacement indicator light turns

red or if the flow of water to the dispenser

or icemaker decreases.

Installing the Filter Cartridge

If you are replacing the cartridge, first

remove the old one by slowly turning

it to the left. Do not pull down on the

cartridge. A small amount of water

may drip down.

Fill the replacement cartridge with

water from the tap to allow for better

flow from the dispenser immediately

after installation.

Lining up the arrow on the cartridge

and the cartridge holder, place the

top of the new cartridge up inside

the holder. Do not push it up into

the holder.

Slowly turn it to the right until the filter

cartridge stops. DO NOT OVERTIGHTEN.

As you turn the cartridge, it will

automatically raise itself into position.

Cartridge will rotate about 1/4 turn.

Run water from the dispenser for

3 minutes (about one and a half

gallons) to clear the system and

prevent sputtering.

Press and hold the RESET WATER FILTER

pad on the dispenser for 3 seconds.

NOTE: A newly-installed water filter

cartridge may cause water to spurt from

the dispenser.

Filter Bypass Plug

You must use the filter bypass plug

when a replacement filter cartridge is not

available. The dispenser and the icemaker

will not operate without the filter or filter

bypass plug.

Replacement Filters:

To order additional filter cartridges

in the United States, visit our Website,

GEAppliances.com, or call GE Parts

and Accessories, 800.626.2002.

GWF

Suggested Retail $34.95 USD

Customers in Canada should consult

the yellow pages for the nearest Camco

Service Center.

Place the top of the cartridge up

inside the cartridge holder and

slowly turn it to the right.

Filter Bypass Plug

Cartridge

Holder

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Slide-Out Spillproof Shelf

The slide-out spillproof shelf allows you

to reach items stored behind others. The

special edges are designed to help prevent

spills from dripping to lower shelves.

To remove:

Slide the shelf out until it reaches the stop,

then press down on the tab and slide the

shelf straight out.

To replace or relocate:

Line the shelf up with the supports and

slide it into place. The shelf can be

repositioned when the door is at 90° or

more. To reposition the shelf, slide the shelf

past the stops and angle downward. Slide

shelf down to the desired position, line up

with the supports and slide into place.

Make sure you push the shelves all the way back

in before you close the door.

Press tab and pull shelf

forward to remove

8

About the shelves and bins.

Refrigerator Door Bins

The refrigerator door bins are adjustable.

To remove: Lift the front of the bin straight

up, then lift up and out.

To replace or relocate: Engage the back side

of the bin in the molded supports of the

door. Then push down on the front of the

bin. Bin will lock in place.

The snugger helps prevent tipping, spilling

or sliding of small items stored on the door

shelf. Place a finger on either side of the

snugger near the rear and move it back

and forth to fit your needs.

Not all features are on all models.

Refrigerator bin

Snugger

Deep Door Shelves

Detachable shelf extenders deepen and

enclose fixed door shelves, providing

more storage room and greater storage

flexibility.

To remove: Lift the shelf extender straight

up then pull out.

To replace: Engage the shelf extender in the

molded supports on the door and push in.

It will lock in place.

9

GEAppliances.com

Not all features are on all models.

QuickSpace

™

Shelf

This shelf splits in half and slides under

itself for storage of tall items on the shelf

below.

This shelf can be removed and replaced

or relocated just like Slide-Out Spillproof

Shelves.

On some models, this shelf can not be used

in the lowest position.

Slide-Out Freezer Shelves

To remove, slide out to the stop position,

lift the front past the stop position, and

slide out.

Make sure you push the shelves all the way back

in before you close the door.

Fixed Freezer Shelves

To remove, lift the shelf up at the left side

and then bring the shelf out.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

10

About the additional features.

Not all features are on all models.

About the refrigerator doors.

Refrigerator Doors

The refrigerator doors may feel different

than the ones you are used to. The special

door opening/closing feature makes sure

the doors close all the way and are securely

sealed.

When opening and closing the door you

will notice a stop position. If the door is

opened past this stop point, the door will

remain open to allow you to load and

unload food more easily. When the door

is only partially open, it will automatically

close.

The resistance you feel at the stop

position will be reduced as the door

is loaded with food.

When the door is only partially open,

it will automatically close.

Beyond this stop the door will

stay open.

ShelfSaver

™

Rack

(on some models)

Use this rack to store

beverage cans for easy

access.

It can also hold a 9″ x 13″

baking dish.

This door rack holds up

to 9 cans.

NOTE: This rack can only be

mounted in the top position

under the dairy bin.

Door Can Rack

(on some models)

Removable Beverage Rack

The beverage rack is designed to hold

a bottle on its side. It can be attached

to any slide-out shelf.

To install:

Line up the large part of the slots on

the top of the rack with the tabs under

the shelf.

Then slide the rack back to lock it

in place.

1

2

About crisper removal.

Not all features are on all models.

Crisper Removal

Crispers can easily be removed by pulling

the drawer straight out and lifting the

drawer up and over the stop location.

If the door prevents you from taking out

the drawers, first try to remove the door

bins. If this does not offer enough

clearance, the refrigerator will need to

be rolled forward until the door opens

enough to slide the drawers out. In some

cases, when you roll the refrigerator out,

you will need to move the refrigerator

to the left or right as you roll it out.

11

About the crispers and pans.

Not all features are on all models.

GEAppliances.com

Adjustable Humidity Crispers

Slide the control all the way to the

HI setting to provide high humidity

recommended for most vegetables.

Slide the control all the way to the

LO setting to provide lower humidity

levels recommended for most fruits.

Low

Humidity

High

Humidity

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Door Alignment

If doors are uneven, adjust the refrigerator

door.

Using a 7/16″ wrench, turn the door

adjusting screw to the right to raise the

door, to the left to lower it.

(A nylon plug, imbedded in the

threads of the pin, prevents the pin

from turning unless a wrench is used.)

After one or two turns of the wrench,

open and close the refrigerator door

and check the alignment at the top

of the doors.

7/16″ Wrench

Fruit and Vegetable Crispers

Excess water that may accumulate in the

bottom of the drawers should be wiped dry.

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Automatic Icemaker

The icemaker will produce seven cubes

per cycle—approximately 100–130 cubes

in a 24-hour period, depending on freezer

compartment temperature, room

temperature, number of door openings

and other use conditions.

If the refrigerator is operated before the

water connection is made to the icemaker,

set the power switch in the O (off) position.

When the refrigerator has been connected

to the water supply, set the power switch to

the l (on) position.

The icemaker will fill with water when it

cools to 15°F (–10°C). A newly-installed

refrigerator may take 12 to 24 hours to

begin making ice cubes.

Throw away the first few batches of ice

to allow the water line to clear.

Be sure nothing interferes with the sweep

of the feeler arm.

When the bin fills to the level of the feeler

arm, the icemaker will stop producing ice.

It is normal for several cubes to be joined

together.

If ice is not used frequently, old ice cubes

will become cloudy, taste stale and shrink.

NOTE: In homes with lower-than-average water

pressure, you may hear the icemaker cycle multiple

times when making one batch of ice.

About the automatic icemaker.

A newly-installed refrigerator may take 12 to 24 hours to begin making ice.

Ice Storage Drawer

To access ice, pull the drawer forward.

To remove the drawer, pull it straight out and

lift it past the stop location.

12

Icemaker

Feeler Arm

Power

Switch

Green

Power Light

Pull the upper freezer shelf straight

out to access the icemaker. Always

be sure to replace the shelf. The

shelf can be used for storage.

Ice Drawer

Shelf

Ice Drawer

About the ice and water dispenser. (on some models) GEAppliances.com

On some models

To Use the Dispenser

Select CUBED ICE , CRUSHED ICE

or WATER .

Press the glass gently against the top of the

dispenser cradle.

The spill shelf is not self-draining. To

reduce water spotting, the shelf and its

grille should be cleaned regularly.

If no water is dispensed when the refrigerator is

first installed, there may be air in the water line

system. Press the dispenser arm for at least two

minutes to remove trapped air from the water

line and to fill the water system. To flush out

impurities in the water line, throw away the first

six glassfuls of water.

CAUTION: Never put fingers or any other

objects into the ice crusher discharge opening.

Locking the Dispenser

Press the LOCK CONTROL

pad for 3 seconds to

lock the dispenser and

control panel. To

unlock, press and

hold the pad again

for 3 seconds.

Dispenser Light

This pad turns the night

light in the dispenser on

and off. The light also

comes on when the

dispenser cradle is

pressed. If this light

burns out, it should be

replaced with a 6 watt

12 V maximum bulb.

Quick Ice

When you need ice

in a hurry, press this

pad to speed up ice

production. This will

increase ice production

for the following

48 hours or until you

press the pad again.

Door Alarm

To set the alarm, press

this pad until the

indicator light comes

on. This alarm will

sound if either door is

open for more than

3 minutes. The light

goes out and the

beeping stops when

you close the door.

Spill Shelf

Important Facts About Your Dispenser

■ Do not add ice from trays or bags to

the storage drawer. It may not crush or

dispense well.

■ Avoid overfilling glass with ice and use

of narrow glasses. Backed-up ice can jam

the chute or cause the door in the chute

to freeze shut. If ice is blocking the

chute, poke it through with a wooden

spoon.

■ Beverages and foods should not be

quick-chilled in the ice storage drawer.

Cans, bottles or food packages in the

storage drawer may cause the icemaker

or auger to jam.

■ To keep dispensed ice from missing

the glass, put the glass close to, but not

touching, the dispenser opening.

■ Some crushed ice may be dispensed even

though you selected CUBED ICE. This

happens occasionally when a few cubes

accidentally get directed to the crusher.

■ After crushed ice is dispensed, some

water may drip from the chute.

■ Sometimes a small mound of snow will

form on the door in the ice chute. This

condition is normal and usually occurs

when you have dispensed crushed ice

repeatedly. The snow will eventually

evaporate.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

13

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Care and cleaning of the refrigerator.

Cleaning the Outside

The dispenser drip area, (on some models)

beneath the grille, should be wiped dry. Water

left in this area may leave deposits. Remove

the deposits by adding undiluted vinegar to

the well. Soak until the deposits disappear

or become loose enough to rinse away.

The dispenser cradle (on some models).

Before cleaning, lock the dispenser by

pressing and holding the LOCK CONTROL

pad for 3 seconds. Clean with warm

water and baking soda solution—about

a tablespoon (15 ml) of baking soda to

a quart (1 liter) of water. Rinse thoroughly

and wipe dry.

The door handles and trim. Clean with

a cloth dampened with soapy water.

Dry with a soft cloth.

The stainless steel panels and door handles

(on some models) can be cleaned with a

commercially available stainless steel

cleaner such as Stainless Steel Magic.

™

Stainless Steel Magic is available at Ace, True

Value, Servistar, HWI and other leading

stores. It is also available through GE Parts

and Accessories, 800.626.2002. Order part

number WX10X15.

Do not use appliance wax or polish on the

stainless steel.

Keep the outside clean. Wipe with a clean

cloth lightly dampened with kitchen

appliance wax or mild liquid dish detergent.

Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish

cloth or wet towel. These may leave a residue

that can erode the paint. Do not use scouring

pads, powdered cleaners, bleach or cleaners

containing bleach because these products can

scratch and weaken the paint finish.

Cleaning the Inside

To help prevent odors, leave an open box of

baking soda in the fresh food and freezer

compartments.

Unplug the refrigerator before cleaning. If this

is not practical, wring excess moisture out

of sponge or cloth when cleaning around

switches, lights or controls.

Use warm water and baking soda solution—

about a tablespoon (15 ml) of baking soda

to a quart (1 liter) of water. This both cleans

and neutralizes odors. Rinse and wipe dry.

Use of any cleaning solution other than that

which is recommended, especially those that

contain petroleum distillates, can crack or

damage the interior of the refrigerator.

Avoid cleaning cold glass shelves with hot water

because the extreme temperature difference

may cause them to break. Handle glass shelves

carefully. Bumping tempered glass can cause

it to shatter.

Do not wash any plastic refrigerator parts in

the dishwasher.

Ice Storage Drawer

on Dispenser Models

To remove:

Set the icemaker power switch to the

O (off) position. Pull the drawer straight out

and then lift past the stop position.

To replace:

When replacing the drawer, be sure to

press it firmly into place. If it does not go

all the way back, remove it and rotate the

drive mechanism 1/4 turn. Then push

the drawer back again.

Rotate

Drive

Mechanism

Dispenser drip area.

14

About the ice and water dispenser.

For long vacations or absences, remove

food and unplug the refrigerator. Clean

the interior with a baking soda solution

of one tablespoon (15 ml) of baking soda

to one quart (1 liter) of water. Leave the

doors open.

Set the icemaker power switch to the

O (off) position and shut off the water supply

to the refrigerator.

If the temperature can drop below freezing,

have a qualified servicer drain the water

supply system (on some models) to prevent

serious property damage due to flooding.

15

GEAppliances.com

Behind the Refrigerator

Be careful when moving the refrigerator

away from the wall. All types of floor

coverings can be damaged, particularly

cushioned coverings and those with

embossed surfaces.

Pull the refrigerator straight out and return

it to position by pushing it straight in.

Moving the refrigerator in a side direction

may result in damage to the floor covering

or refrigerator.

When pushing the refrigerator back, make sure

you don’t roll over the power cord or icemaker

supply line (on some models).

Preparing for Vacation

Preparing to Move

Secure all loose items such as shelves and

drawers by taping them securely in place

to prevent damage.

When using a hand truck to move the

refrigerator, do not rest the front or back

of the refrigerator against the hand truck.

This could damage the refrigerator. Handle

only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright

position during moving.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Replacing the light bulbs.

Setting either or both controls to 0 does not remove power to the light circuit.

Refrigerator Compartment—Upper Light

Unplug the refrigerator.

The bulb is located at the top of the

compartment, inside the dome light

shield. To remove the shield, place your

finger in the pocket at the back of the

shield. Pull the shield forward and down.

After replacing the bulb with an

appliance bulb of the same or lower

wattage, replace the light shield.

Plug the refrigerator back in.

Freezer Compartment

Unplug the refrigerator.

Remove the shelf just above the light

shield. (The shelf will be easier to

remove if it is emptied first.) On some

models, a screw at the top of the light

shield will need to be removed.

To remove the light shield, press in on

the sides, and lift up and out. On some

models, lift the light shield up and pull

it out.

Replace the bulb with an appliance

bulb of the same or lower wattage,

and reinstall the light shield. When

reinstalling the light shield, make

sure the top tabs snap securely

into place. Replace the screw (on

some models).

Reinstall the shelf and plug the

refrigerator back in.

16

Dispenser

Unplug the refrigerator.

The bulb is located on the

dispenser under the control panel.

Remove the light bulb by turning

it counterclockwise.

Replace the bulb with a bulb of the

same size and wattage.

Plug the refrigerator back in.

Pocket

Refrigerator Compartment—Lower Light

This light is located above the top drawer.

Unplug the refrigerator.

Lift the light shield up and pull it out.

After replacing the bulb with an

appliance bulb of the same or lower

wattage, replace the shield.

Plug the refrigerator back in.

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

•

IMPORTANT — Save these

instructions for local inspector’s use.

•

IMPORTANT — Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these

instructions for future reference.

• Skill level – Installation of this appliance

requires basic mechanical skills.

• Completion time – Refrigerator Installation

30 minutes

Water Line Installation

30 minutes

• Proper installation is the responsibility of

the installer.

• Product failure due to improper installation

is not covered under the Warranty.

If the refrigerator has already been installed,

remove the base grille (see Step 2 in Moving

the Refrigerator), then skip to Step 5 in

Installing the Refrigerator.

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com

In Canada, call 1.800.361.3400 or Visit our Website at: www.geappliances.ca

Installation

Refrigerator

Instructions

Models 23 & 25

If the refrigerator has an icemaker, it will have

to be connected to a cold water line. A GE

water supply kit (containing tubing, shutoff

valve, fittings and instructions) is available at

extra cost from your dealer, by visiting our

Website at www.GEAppliances.com (in

Canada at www.geappliances.ca) or from

Parts and Accessories, 800.626.2002 (in

Canada 1.888.261.3055).

PREPARATION

WATER SUPPLY TO THE ICEMAKER

TOOLS YOU WILL NEED

17

Phillips Head Screwdriver

3/8″ and 5/16″ Socket 1/2″ and 7/16″ Wrench

Plastic Putty Knife

18

Installation Instructions

LOADING THE RERIGERATOR

ONTO A HAND TRUCK

Leave all tape and door pads on doors

until the refrigerator is in its final location.

To move the refrigerator, use a padded

hand truck. Center the refrigerator on the

hand truck and secure the strap around

the refrigerator. DO NOT OVERTIGHTEN

THE STRAP.

1

REMOVE THE BASE GRILLE

Remove the grille by removing the two

Phillips head screws.

2

If the refrigerator must go through

any entrance that is less than 38″

wide, the doors must be removed.

Proceed to Step 3.

DO NOT remove the handles.

If all entrances are more than

38″ wide, skip to Installing

the Refrigerator.

DISCONNECT THE WATER

COUPLING (on some models)

If the refrigerator has a water dispenser,

there is a water line from the cabinet into

the bottom hinge on the freezer door that

must be disconnected.

To disconnect, push in on the white collar

of the coupling and pull out the tubing.

3

White collar

Bottom

freezer

hinge

MOVING THE REFRIGERATOR

19

Installation Instructions

DISCONNECT THE POWER

COUPLING (on some models)

If the refrigerator has a water dispenser,

there is a power line (harness) from the

cabinet into the bottom hinge on the

freezer door that must be disconnected.

To disconnect, pull apart at the coupling.

4

Bottom

freezer

hinge

DISCONNECT THE ELECTRICAL

CONNECTORS (on some models)

If the refrigerator has a refreshment

center, there are electrical connectors

(harnesses) from the cabinet into the

bottom hinge on the refrigerator door

that must be disconnected.

To disconnect, pull apart each connector.

5

Bottom

refrigerator

hinge

CLOSE THE FREEZER AND

REFRIGERATOR DOORS

6

REMOVE THE FREEZER DOOR

Remove the freezer door top hinge cover

by either squeezing it and pulling it up or

by prying it off with a plastic putty knife.

Remove the two 5/16” hex head screws,

then lift the hinge straight up to free the

hinge pin.

Open the freezer door to 90.°

7

A

C

B

5/16” Hex Head

90°

20

Installation Instructions

MOVING THE REFRIGERATOR (CONT.)

REMOVE THE

FREEZER DOOR (cont.)

As one person slowly lifts the freezer door

up and off the bottom hinge, the second

person should carefully guide the water

line and power line (harness) through the

bottom hinge.

Set the door on a non-scratching surface

with the inside up.

7

D

E

90°

REMOVE THE

REFRIGERATOR DOOR

Remove the refrigerator door top hinge

cover by either squeezing it and pulling

it up or by prying it off with a plastic

putty knife.

8

A

REMOVE THE

REFRIGERATOR DOOR (cont.)

Remove the two 5/16” hex head screws,

then lift the hinge straight up to free the

hinge pin.

Open the refrigerator door to 90.°

8

B

C

5/16” Hex Head

90°

Page is loading ...

GE 23, 25 User manual

This manual is also suitable for

GE 23, 25 User manual

in other languages

Related papers

Other documents