Tripp Lite PDUMH15HVNET Owner's manual

1

Owner’s Manual

Warranty

Registration

Register online today for a chance

to win a FREE Tripp Lite product!

www.tripplite.com/warranty

PDUMH15NET/PDUMH20NET

Switched Rack PDU

• 120V, 60Hz AC Input and Output

PDUMH15HVNET/PDUMH20HVNET

Switched Rack PDU

• 208/230V, 50/60Hz AC Input and Output

Important Safety Instructions 2

Installation 2

Features 9

Technical Support 12

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

Configuration and Operation 11

Warranty and Warranty Registration 12

Español 13

Français 25

201110149-93-2718.indd 1 11/9/2011 11:17:25 AM

A

B

A

1-1

C

D

2

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be

followed during the installation, operation, and storage of this product.

Failure to heed these instructions and warnings may affect the product

warranty.

Important Safety Instructions

• ThePDUprovidesconvenientmultipleoutlets,butitDOESNOTprovidesurgeorlinenoise

 protectionforconnectedequipment.

• ThePDUisdesignedforindooruseonlyinacontrolledenvironmentawayfromexcessmoisture,

 temperatureextremes,conductivecontaminants,dustordirectsunlight.

• DonotconnectthePDUtoanungroundedoutletortoextensioncordsoradaptersthateliminate

 theconnectiontoground.

• ThepowerrequirementforeachpieceofequipmentconnectedtothePDUmustnotexceedthe

 individualoutlet’sloadrating.

• ThetotalpowerrequirementforequipmentconnectedtothePDUmustnotexceedthemaximum

 loadratingforthePDU.

• DonotdrillintoorattempttoopenanypartofthePDUhousing.Therearenouser-serviceable

 partsinside.

• DonotattempttomodifythePDU,includingtheinputplugsandpowercables.

• DonotattempttousethePDUifanypartofitbecomesdamaged.

• DonotattempttomountthePDUtoaninsecureorunstablesurface.

• Neverattempttoinstallelectricalequipmentduringathunderstorm.

• Useofthisequipmentinlifesupportapplicationswherefailureofthisequipmentcanreasonably

 beexpectedtocausethefailureofthelifesupportequipmentortosignificantlyaffectitssafetyor

 effectivenessisnotrecommended.Donotusethisequipmentinthepresenceofaflammable

 anestheticmixturewithair,oxygenornitrousoxide.

Installation

Mounting the PDU

ThePDUsupportsfiveprimarymountingconfigurations:1URack,0URack(Vertical),Wall,Under-

CounterandReduced-Depth.

Note: Regardless of configuration, the user must determine the fitness of hardware and procedures before mounting. The PDU and

included hardware are designed for common rack and rack enclosure types and may not be appropriate for all applications. Exact

mounting configurations may vary. Screws for attaching the mounting brackets and cord retention shelf to the PDU are included. Use

only the screws supplied by the manufacturer, or their exact equivalent (#6-32, 3/16" flat head).

1-1 1U Rack Mounting: Use 3 screws

A

to

attacheachofthe2longermountingbrackets

B

tothePDUasshown.YoucanmountthePDUin

arecessedpositionbyattachingthemounting

bracketssotheyextendbeyondthefrontpanelof

thePDU.(Ifyouplantousethecordretention

shelf,attachthemountingbracketsinarecessed

position.)MountthePDUintherackby

inserting4user-suppliedscrews

C

through the

mountingbrackets

D

andintothemounting

holesoftherackrails.

201110149-93-2718.indd 2 11/9/2011 11:17:26 AM

1-2

A

B

C

D

1-3

A

B

C

D

A

B

1-4

C

D

1-6

A

B

1-5

C

D

A

B

3

1-2 0U Rack Mounting: Use 3 screws

A

to

attacheachofthe2shortermountingbrackets

B

tothePDUasshown.MountthePDU

verticallybyinserting2ormoreuser-supplied

screws

C

throughthemountingbrackets

D

and

intomountingpointsintherackorrack

enclosure.

1-3 Wall Mounting: Use 3 screws

A

to attach

eachofthe2shortermountingbrackets

B

to the

PDUasshown.MountthePDUtothewallby

inserting2ormoreuser-suppliedscrews

C

throughthemountingbrackets

D

andinto

securemountingpoints.

1-4 Under-Counter Mounting: Use 3 screws

A

toattacheachofthe2shortermounting

brackets

B

tothePDUasshown.Mountthe

PDUunderthecounterbyinserting2ormore

user-suppliedscrews

C

throughthemounting

brackets

D

andintosecuremountingpoints.

1-5 Reduced-Depth Mounting: Use 3 screws

A

toattacheachofthe2shortermounting

brackets

B

tothePDUasshown.Mountthe

PDUtoastablesurfacewiththeoutletsfacing

upwardbyinserting2ormoreuser-supplied

screws

C

throughthemountingbrackets

D

and

intosecuremountingpoints.

1-6 Cord Retention Shelf Attachment

(Optional): Use 2 screws

A

to attach the cord

retentionshelf

B

tothefrontpanelofthePDU.

Installation continued

201110149-93-2718.indd 3 11/9/2011 11:17:28 AM

2-1

88

PDUMH15HVNET

PDUMH15NET/PDUMH20NET

A

B

C

88

2-2

PDUMH20HVNET

B

A

C

A

2-3

4

Connecting the PDU

2-1 NEMA Adapter Connection (Optional -

PDUMH20HVNET Only): The

PDUMH20HVNETincludesaplugadapterthat

addsaNEMAL6-20Pplugtotheinputpower

cord.Usethisadapteronlyifyouwillbe

connectingthePDUMH20HVNETtoaNEMA

L6-20Routlet.InserttheIEC60320C19

connector

A

oftheadapterintotheIEC60320

C20connector

B

oftheinputpowercord.

Securetheconnectionwiththeretentionbracket

C

byusingtheincludedboltstofastenthetwo

halvesofthebracketaroundtheconnectionas

shown.Caution: To avoid the risk of electric

shock, ensure that the Neutral (L2) conductor

has been identified before connecting the PDU.

2-2 Input Power Cord Connection (Select

Models with Unattached Power Cords Only):

InserttheIEC60320C19(PDUMH20HVNET)

orIEC60320C13(PDUMH15HVNET)

connector

A

oftheinputpowercordintothe

IEC60320C20(PDUMH20HVNET)orIEC

60320C14(PDUMH15HVNET)inlet

B

ofthe

PDU.Connecttheotherendoftheinputpower

cord

C

toacompatiblesourceofACpower,

suchasaUPSsystem,PDUorutilityoutlet.

ThePDUshouldbeprovidedwithover-current

protection:PDUMH20HVNETshouldbe

providedwithamaximum20Abranch-rated

over-currentprotectiondevice;

PDUMH15HVNETshouldbeprovidedwitha

maximum15Abranch-ratedover-current

protectiondevice.

Note: The AC power source should not share a circuit with a

heavy electrical load (such as an air conditioner or

refrigerator).

2-3 Connect Input Power Cord

(PDUMH15NET and PDUMH20NET):

Connecttheinputplug

A

toacompatiblesource

ofACpower,suchasaUPSsystem,PDUor

utilityoutlet.ThePDUshouldbeprovidedwith

over-currentprotection:PDUMH15NETwitha

maximum15Abranch-ratedprotectiondevice.

PDUMH20NETwithamaximum20Abranch-

ratedprotectiondevice.

Installation continued

201110149-93-2718.indd 4 11/9/2011 11:17:30 AM

15

2-4

A

B

C

D

15

2-5

PDUMH20NET

PDUMH15NET

PDUMH15HVNET/PDUMH20HVNET

B

D

C

5

Installation continued

2-4 Equipment Power Cord Connection:

InserttheIEC60320C14connectors

A

ofthe

equipmentpowercordsintotheIEC60320C13

output receptacles

B

ofthePDU

(PDUMH15HVNETandPDUMH20HVNET).

InsertpowercordsintotheNEMA5-15Routput

receptacles

B

(PDUMH15NET)orNEMA

5-15/20Routputreceptacles

B

(PDUMH20NET).TheLED

C

neareachoutput

receptacleilluminateswhenthereceptacleis

readytodistributeliveACpower.Thedigital

load meter

D

willdisplaythetotalconnected

equipmentloadinamps.

2-5 Cord Retention (Optional): Ifyou

attachedthecordretentionshelfinstep

1-6

, tie

theinputpowercordandeachequipmentpower

cordtotheretentionshelf.Attacheachcordto

theretentionshelfbyloopingthecordand

securingittoanattachmentpointwithoneof

theincludedcableties.Makesurethateachcord

canbeunpluggedfromthePDUwithout

removingthecabletie.

201110149-93-2718.indd 5 11/9/2011 11:17:31 AM

15

4-1

A

B

C

A

6

Installation continued

Networking the PDU

Note: The MAC address of the PDU (a 12-digit string in this format: 000667xxxxxx) is printed on a label attached to the PDU enclosure.

The MAC address is also printed on a label attached to the internal network card.

Ifyournetwork'sDHCPserverwillassignadynamicIPaddresstothePDUautomatically,gotoStep

4-1

.IfyouwillassignastaticIPaddresstothePDUmanually,gotoStep

5-1

.Ifyouareuncertain

whichmethodtouse,contactyournetworkadministratorforassistancebeforecontinuingthe

installationprocess.

Dynamic IP Address Assignment

4-1 Connect PDU to Network:WhilethePDU

ispowered,connectastandardEthernetpatch

cabletotheRJ-45Ethernetport

A

onthePDU.

Note: This port is not compatible with PoE

(Power over Ethernet) applications.ThePDU

willattempttoobtainanIPaddressviaDHCP.

Thismaytakeaslongasseveralminutes,

dependingonyournetworkenvironment.

4-2 Discover IP Address:ContactyournetworkadministratortodeterminewhichdynamicIP

addresshasbeenassignedtothePDUbytheDHCPserver.ThePDUcanbeidentifiedontheDHCP

serverbyreferringtoitsMACaddress.(TheMACaddressisa12-digitstringinthisformat:

000667xxxxxx.RefertotheMACaddresslabelattachedtothePDU.)Youmaywishtorequestalong-

termleaseperiodfortheIPaddress,dependingonyourapplication.AfteryouhavediscoveredtheIP

address,skipSteps

5-1

through

5-6

andproceeddirectlytoStep

6-1

.

Static IP Address Assignment

5-1 Determine IP Information:Before

assigningastaticIPaddress,you'llneedtoknow

theIPaddress,gatewayaddressandsubnetmask.

Ifyoudonothavethisinformation,contactyour

networkadministratorforassistance.

5-2 Configure Terminal Emulation Program:

OpenaVT100-compatibleterminalemulation

program(suchastheHyperTerminalprogram

bundledwithMicrosoft

®

Windows

®

)ona

computerwithanavailableDB9serialport.(A

notebookcomputermaybethemostconvenient

choice.)Settheterminalemulationprogramto

usetheCOMport

A

thatcorrespondstothe

computer’sDB9serialport.Specifythe

parameters

B

requiredtocommunicatewiththe

PDUterminalinterface:

Bits per second: 9600

Data bits: 8

Parity: None

Stop bits: 1

Flow control: None

Iftheterminalemulationprogramsupports

multipleemulationmodes,youmayalsoneed

tospecifyVT100emulation

C

.

201110149-93-2718.indd 6 11/9/2011 11:17:32 AM

5-5

5-3

5-4

A

B

C

D

A

7

Installation continued

Networking the PDU continued

5-3 Connect PDU to Computer: Use the

mini-DINtoDB9serialcable(partnumber

73-1025)includedwiththePDUtoconnect

thePDUtothecomputer.Thecircular

connector

A

atoneendofthecableattachesto

the8-pinmini-DINserialport

B

onthePDU.

(Aligntheconnectorcarefullytoavoid

damagingthepins.)TheDB9connector

C

at

theotherendofthecableconnectstothe

computer'sserialport

D

.

5-4 Connect PDU to Network: While the

PDUispowered,connectastandardEthernet

patchcabletotheRJ-45Ethernetport

A

on

thePDU.Note: This port is not compatible with PoE

(Power over Ethernet) applications.

5-5 Configure PDU in Terminal Mode:

Afterabriefpause,aninitializationpage

shouldappearintheterminalemulation

program.Pressanykeyonthekeyboardwithin

10secondstochangethePDUsettings.(Ifthe

10-secondperiodhaselapsed,youcanreboot

thePDUbypoweringdowncompletelyand

thenrestoringpower.)

Followthesequenceofresponsesbelowin

ordertoassignanIPaddresstothePDU.The

defaultterminalmoderootpasswordis

TrippLite.SampleIPsettingsareshown-

supplyyourownIPinformationwhenyou

configureyourPDU.

Press A to Accept the settings, or M to Modify? M

Enter the root password: *********

Reset configuration to default values (Y/N)? N

For each of the following questions, you can press <Return> to select the value shown in

braces, or you can enter a new value.

NETWORK INTERFACE PARAMETERS:

Should this target obtain IP settings from the network?[N] N

Static IP address [192.168.1.19]? 192.168.0.123

Static IP address is 192.168.0.123

Subnet Mask IP address [255.255.0.0]? 255.255.255.0

Subnet Mask IP address is 255.255.255.0

Gateway address IP address [192.168.1.1]? 192.168.0.1

Gateway address IP address is 192.168.0.1

Youcanalsochangetherootpassword,real-timeclockandothersettings.(TrippLiterecommends

againstchangingthedefaultsettingsunlessyouareanadvanceduserwithaspecificpurpose.)After

youhavefinishedenteringsettings,thePDUwillsavechangestomemoryandreboot(thismaytake

severalminutes).AfterthePDUreboots,theinitializationpageshoulddisplaythenewstaticIP

settings.

5-6 Remove Serial Cable: RemovetheserialcablefromthePDUandproceedtoStep

6-1

.

201110149-93-2718.indd 7 11/9/2011 11:17:32 AM

A

B

8

Installation continued

Networking the PDU continued

Testing Network Connection

6-1 Access PDU with Web Browser:Afteran

IPaddresshasbeenassignedtothePDU,attempt

toaccessitwithaWebbrowserthatsupports

frames,formsandJava

™

.OpenaWebbrowser

onacomputerconnectedtotheLANandenter

theIPaddressassignedtothePDU.Youshould

bepromptedforapassword

A

.Theusernameis

adminandthedefaultpasswordisadmin.After

youentertheusernameandpassword,the

PowerAlertStatus page

B

willappearinthe

browserwindow.Formoreinformationabout

configurationandoperationofthePDUviathe

PowerAlertinterface,refertothe

SNMPWEBCARDUser'sGuide,includedonthe

CD-ROMbundledwiththePDU.

Note for Network Management System Users Only: Two MIB files

- Tripplite.mib and RFC1628.mib - must be loaded on each

Network Management Station that will monitor the PDU via

SNMP. The files are provided on the CD-ROM included in the

product package.

201110149-93-2718.indd 8 11/9/2011 11:17:33 AM

A

B

A

B

9

Features

AC Input Power Inlet (Model PDUMH15HVNET):TheIEC

60320C14inletconnectstothedetachableACInputPowerCord.

AC Input Power Inlet (Model PDUMH20HVNET):TheIEC

60320C20inletconnectstothedetachableACInputPowerCord.

AC Input Power Cord (Model PDUMH15HVNET): The

detachablecordhasanIEC60320C13connector

A

andanIEC

60320C14connector

B

.

AC Input Power Cord (Model PDUMH20HVNET): The

detachablecordhasanIEC60320C19connector

A

andanIEC

60320C20connector

B

.

AC Input Power Cord (Model PDUMH15NET): The cord is

permanentlyattachedtothePDUandhasaNEMA5-15Pplug.

AC Input Power Cord (Model PDUMH20NET): The cord is

permanentlyattachedtothePDUandhasaNEMAL5-20Pplug.

AC Input Adapter (Model PDUMH20HVNET): The adapter

convertstheACinputpowercordtoaNEMAL6-20Pplug.The

includedretentionbracket(notshown)securestheconnection.

AC Input Adapter (Model PDUMH20NET): Theadapterconverts

NEMAL5-20PinputplugstoNEMA5-20Pinputplugs.

201110149-93-2718.indd 9 11/9/2011 11:17:34 AM

10

NEMA 5-15R Output Receptacles (PDUMH15NET): During

normaloperation,theoutputreceptaclesdistributeACpowerto

connectedequipment.Whenanoutletislive,theassociatedLED

illuminates.

NEMA 5-15/20R Output Receptacles (PDUMH20NET): During

normaloperation,theoutputreceptaclesdistributeACpowerto

connectedequipment.Whenanoutletislive,theassociatedLED

illuminates.

IEC 60320 C13 Output Receptacles (PDUMH15HVNET &

PDUMH20HVNET):Duringnormaloperation,theoutput

receptaclesdistributeACpowertoconnectedequipment.Whenan

outletislive,theassociatedLEDilluminates.

Digital Load Meter (Ammeter):Thetotalelectricalcurrentdrawn

byconnectedequipmentisdisplayedonthemeterinamperes.

Cord Retention Shelf:WhenitisattachedtothePDU,thecord

retentionshelfprovidessecureattachmentpointsfortheinputcord

andconnectedequipmentcords.Usetheincludedcabletiesto

securethecordstotheshelf.

Longer Mounting Brackets:UsethesebracketstomountthePDU

horizontallyinastandardrackorrackenclosure.Themounting

depthcanbeadjustedbyattachingthebracketstodifferentpositions

onthePDU.

Shorter Mounting Brackets:UsethesebracketstomountthePDU

ina0Urack,wallorunder-counterconfiguration.

Factory Port:Theportisreservedforconfigurationbyfactory

authorizedpersonnelonly.Donotconnectanythingtotheport.

Features continued

201110149-93-2718.indd 10 11/9/2011 11:17:36 AM

A

B

A

B

11

Features continued

PS/2 Port: UsethisporttoconnectaTrippLiteENVIROSENSE

environmentalsensortoprovideremotetemperature/humidity

monitoringandadrycontactinterfacetocontrolandmonitoralarm,

securityandtelecomdevices.ContactTrippLiteCustomerSupport

at(773)869-1234fororderinginformation.Note:Donotconnecta

keyboardormousetothisport.

Mini-DIN Serial Port: Usethisporttoprovideadirectterminal

connectiontoacomputerwithaterminalemulationprogram.A

serialcable(partnumber73-1025)isincludedwiththePDU.Ifyou

needtoorderareplacementcable,contactTrippLiteCustomer

Supportat(773)869-1234.

Ethernet Port: UsethisRJ-45jacktoconnectthePDUtothe

networkwithastandardEthernetpatchcable.TheLinkLED

A

and

StatusLED

B

indicateseveraloperatingconditions,asshowninthe

tablebelow.This port is not compatible with PoE (Power Over

Ethernet) applications.

Network Operating Conditions

A

Link LED Color

Off No Network Connection

Flashing Amber 100 Mbps Network Connection

Flashing Green 10 Mbps Network Connection

B

Status LED Color

Off Card Not Initialized

Steady Green Card Initialized and Operational

Flashing Amber Error - Card Not Initialized

Configuration and Operation

Remote Monitoring and Control

ThePDUprovidesremotemonitoring

A

, outlet

control

B

andmoreviaWebbrowser,telnetand

SNMP-basedNetworkManagementSystems.

Formoreinformationaboutconfigurationand

operationofthePDUviathePowerAlertWeb

browserinterface,refertothe

SNMPWEBCARDUser'sGuide,includedon

theCD-ROMbundledwiththePDU.

201110149-93-2718.indd 11 11/9/2011 11:17:37 AM

12

Warranty and Warranty Registration

LIMITED WARRANTY

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material

and workmanship for a period of 2 years from the date of initial purchase. If the product should prove defective in material or

workmanship within that period, Seller will repair or replace the product, in its sole discretion. Service under this Warranty can

only be obtained by your delivering or shipping the product (with all shipping or delivery charges prepaid) to: Tripp Lite, 1111

W. 35th Street, Chicago, IL 60609 USA. Seller will pay return shipping charges. Visit www.tripplite.com/support before sending

any equipment back for repair.

THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE,

ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET

FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING

ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET

FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES.

(Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This Warranty

gives you specific legal rights, and you may have other rights which vary from jurisdiction to jurisdiction).

WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for

the use intended. Since individual applications are subject to great variation, the manufacturer makes no representation or

warranty as to the suitability or fitness of these devices for any specific application.

WARRANTY REGISTRATION

Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You'll be automatically entered

into a drawing for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

FCC Notice, Class A

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required

to correct the interference at his own expense. The user must use shielded cables and connectors with this equipment. Any

changes or modifications to this equipment not expressly approved by Tripp Lite could void the user’s authority to operate this

equipment.

Regulatory Compliance Identification Numbers

For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique

series number. The series number can be found on the product nameplate label, along with all required approval markings and

information. When requesting compliance information for this product, always refer to the series number. The series number

should not be confused with the marking name or model number of the product.

WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)

Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy

new electrical and electronic equipment from Tripp Lite they are entitled to:

• Sendoldequipmentforrecyclingonaone-for-one,like-for-likebasis(thisvariesdependingonthecountry)

• Sendthenewequipmentbackforrecyclingwhenthisultimatelybecomeswaste

The policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice.

Technical Support

Website:www.tripplite.com/support

E-mail:[email protected]

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

201110149•932718-EN

201110149-93-2718.indd 12 11/9/2011 11:17:37 AM

13

Manual del propietario

PDUMH15NET/PDUMH20NET

PDU con tomas de corriente controlables para bastidor

• 120V, 60Hz AC Input y Output

PDUMH15HVNET/PDUMH20HVNET

PDU con tomas de corriente controlables para bastidor

• 208/230V, 50/60Hz AC Input y Output

Instrucciones de seguridad importantes 14

Instalación 14

Características 21

Soporte técnico 24

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

Configuración y operación 23

Garantía 24

English 13

Français 25

201110149-93-2718.indd 13 11/9/2011 11:17:37 AM

Page is loading ...

Tripp Lite PDUMH15HVNET Owner's manual

Tripp Lite PDUMH15HVNET Owner's manual

in other languages

Related papers

Other documents