Sony CFD-E77L User manual

CD Radio

Cassette-Corder

3-228-965-33 (1)

CFD-E70L

CFD-E75

CFD-E75L

CFD-E77L

Operating Instructions page 2

GB

Manual de instrucciones página 2

ES

GB

ES

2

GB

Warning

To prevent fire or shock hazard,

do not expose the player to rain

or moisture.

To avoid electrical shock, do not

open the cabinet. Refer

servicing to qualified personnel

only.

Information

For customers in Europe

This Compact Disc player is classified as a

CLASS 1 LASER product.

The CLASS 1 LASER PRODUCT label is located

at the rear.

Warning

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

To prevent fire or shock hazard, do not place

objects filled with liquids, such as vases, on the

appliance.

Notice for customers in the United

Kingdom

A moulded plug complying with BS 1363 is fitted

to this equipment for your safety and convenience.

Should the fuse in the plug supplied need to be

replaced, same rating fuse approved by ASTA or

BSI to BS 1362, (i.e. marked with or mark)

must be used.

If the plug supplied with this equipment has a

detachable fuse cover, be sure to attach the fuse

cover after you change the fuse. Never use the

plug without the fuse cover. If you should lose the

fuse cover, please contact your nearest Sony

service station.

About this manual

The instructions in this manual are for the CFD-

E70L, CFD-E75, CFD-E75L and CFD-E77L.

Before you start reading, check your model

number. The CFD-E75L is the model used for

illustration purpose.

Note

The name of the switch to turn on/off this player is

indicated as below:

“OPERATE”: CFD-E70L/E75L/E77L

“POWER”: CFD-E75

Basic Operations

3

GB

Table of contents

Basic Operations

Playing a CD .................................................. 4

Listening to the radio...................................... 6

Playing a tape ................................................. 8

Recording on a tape ...................................... 10

The CD Player

Using the display .......................................... 12

Locating a specific point in a track .............. 12

Playing tracks repeatedly

(Repeat Play) ............................................ 13

Playing tracks in random order

(Shuffle Play) ........................................... 14

Creating your own programme

(Programme Play)..................................... 15

The Radio

Presetting radio stations................................ 16

Playing preset radio stations ......................... 17

The Audio Emphasis

Selecting the audio emphasis

(MEGA BASS)......................................... 18

The Timer

Setting the clock ........................................... 19

Waking up to music...................................... 20

Falling asleep to music ................................. 21

Using the countdown timer .......................... 22

Setting Up

Choosing the power sources ......................... 24

Additional Information

Precautions ................................................... 26

Troubleshooting............................................ 27

Maintenance ................................................. 30

Specifications ............................................... 31

Index ............................................................. 32

GB

4

GB

Connect the supplied mains lead (see page 24).

1 Press ZPUSH OPEN/CLOSE down

to open the CD compartment and

place the CD on the CD

compartment.

2 Close the lid of the CD compartment.

3 Press u (N on the remote, CFD-

E75/E75L/E77L only).

The player turns on (direct power-on)

and plays all the tracks once.

Basic Operations

3

Playing a CD

Display

With the label side up

1, 2

PUSH OPEN/CLOSE

Playing timeTrack number

Basic Operations

5

GB

Use these buttons for additional operations

OPERATE

(or POWER)

x

u

Jog dial

VOLUME +, –

ZPUSH

OPEN/CLOSE

To Do this

adjust the volume Press VOLUME +, – (VOL +, – on

the remote, CFD-E75/E75L/E77L

only).

stop playback Press x.

pause playback Press u (X on the remote, CFD-

E75/E75L/E77L only).

Press the button again to resume

play after pause.

go to the next track Turn the jog dial clockwise.

(On the remote, press >, CFD-

E75/E75L/E77L only.)

go back to the previous track Turn the jog dial counterclockwise.

(On the remote, press ., CFD-

E75/E75L/E77L only.)

remove the CD Press ZPUSH OPEN/CLOSE.

turn on/off the player Press OPERATE (or POWER, see

page 2).

About CD-Rs/CD-RWs

This player is compatible with CD-Rs/CD-RWs but

playback capability may vary depending on the quality of

the disc, the recording device and application software.

6

GB

Listening to the radio

Connect the supplied mains lead (see page 24).

1 Press RADIO BAND•AUTO

PRESET until the band you want

appears in the display (direct power-

on).

Each time you press the button, the

band changes as follows:

CFD-E75: “FM” t “AM”

CFD-E70L/E75L/E77L: “FM” t “MW” t “LW”

2 Hold down TUNE + or – until the

frequency digits begin to change in

the display.

The player automatically scans the

radio frequencies and stops when it

finds a clear station.

If you can't tune in a station, press

the button repeatedly to change the

frequency step by step.

Display

Indicates an FM stereo

broadcast

12

RADIO

AUTO PRESET

BAND

TU

N

E

Basic Operations

7

GB

Use these buttons for additional operations

To Press

adjust the volume VOLUME +, –

(VOL +, – on the remote, CFD-E75/

E75L/E77L only)

turn on/off the radio OPERATE (or POWER, see page 2)

To improve broadcast reception

Reorient the aerial for FM. Reorient the player itself for

AM or MW/LW.

for FM for AM/MW/LW

Tips

• If the FM broadcast is

noisy, press MODE until

“Mono” appears in the

display and the radio will

play in monaural.

• If you need to change the

AM/MW tuning interval,

see page 25.

OPERATE

(or POWER)

VOLUME +, –

MODE

8

GB

Playing a tape

Connect the supplied mains lead (see page 24).

1 Press xZ to open the tape

compartment and insert a recorded

tape. Use TYPE I (normal) tape only.

Close the compartment.

2 Press n.

The player turns on (direct power-on)

and starts playing.

With the side you want

to play facing you

Display

21

Basic Operations

9

GB

Use these buttons for additional operations

To Press

adjust the volume VOLUME +, –

(VOL +, – on the remote, CFD-

E75/E75L/E77L only)

stop playback xZ

fast-forward or rewind the tape m or M

pause playback X

Press the button again to

resume play after pause.

eject the cassette xZ

turn on/off the player OPERATE (or POWER, see

page 2)

xZ

X

m, M

OPERATE

(or POWER)

VOLUME +, –

10

GB

Recording on a tape

Connect the supplied mains lead (see page 24).

1 Press xZ to open the tape

compartment and insert a blank tape.

Use TYPE I (normal) tape only.

2 Select the programme source you

want to record.

To record from the CD player, insert

a CD (see page 4) and press x on the

CD section.

To record from the radio, tune in the

station you want (see page 6).

3

With the side you want to

record on facing you

Display

1

RADIO

AUTO PRESET

BAND

Basic Operations

11

GB

3 Press z to start recording

(n is depressed automatically).

Use these buttons for additional operations

Tips

• Adjusting the volume or the

audio emphasis (see page

18) will not affect the

recording level.

• If the AM/MW/LW

programme makes a

whistling sound after you've

pressed z in step 3, press

MODE to select the

position of ISS

(Interference Suppress

Switch) that most decreases

the noise.

• For the best results, use the

AC power as a power

source.

• To erase a recording,

proceed as follows:

1 Insert the tape whose

recording you want to

erase.

2 Press X.

3 Press n.

4 Press z.

5 Press X.

xZ

X

OPERATE

(or POWER)

MODE

n

To Press

stop recording xZ

pause recording X

Press the button again to resume

recording.

turn on/off the player OPERATE (or POWER, see page 2)

12

GB

The CD Player

Using the display

You can check information about the CD

using the display.

Checking the remaining time

Press DSPL•ENT MEM while playing a CD.

To display

Press

DSPL•

ENT MEM

the current track number once

and remaining time

on the current track*

the number of tracks left twice

and remaining time on the CD

the current track number three times

and playing time

* For a track whose number is more than 20, the

remaining time appears as “– –:– –”.

Total playing

time

Total track

number

DSPL

ENT MEM

Checking the total track

number and playing time

Press DSPL•ENT MEM in stop mode.

Locating a specific

point in a track

You can quickly find a specific point in

a track while playing a CD.

You can also locate any track on a CD using

the number buttons on the remote (CFD-

E75/E75L/E77L only).

To locate Press

a point while listening to M (forward) or m

the sound (backward) while

playing and hold down

until you find the point.

(On the remote, use

> or ., CFD-

E75/E75L/E77L only.)

a point while observing M (forward) or m

the display (backward) in pause

and hold down until

you find the point.

(On the remote, use

> or ., CFD-

E75/E75L/E77L only.)

a specific track directly the number button of

(CFD-E75/E75L/E77L the track.

only)

m M

13

GB

The CD Player

Playing tracks

repeatedly (Repeat Play)

You can play tracks repeatedly in normal,

shuffle or programme play modes (see pages

14 - 15).

1 Press x.

“Cd” appears in the display.

2 Proceed as follows.

To repeat

a single track

all the tracks

tracks in

random order

programmed

tracks

x

MODEJog dial

u

Note

You cannot locate a specific track if “SHUF” or

"PGM" is lit in the display. Turn off the indication

by pressing x (CFD-E75/E75L/E77L only).

Tip

When you locate a track numbered over 10, press

>10 first, then the corresponding number buttons.

Example:To play track number 23, press >10 first,

then 2 and 3 (CFD-E75/E75L/E77L only).

continued

Do this

1 Press MODE until

“REPEAT 1” appears.

2 Turn the jog dial to select

the track that you want to

repeat.

3 Press u.

1 Press MODE until

“REPEAT ALL” appears.

2 Press u.

1 Press MODE until “SHUF

REPEAT” appears.

2 Press u.

1 Press MODE until “PGM

REPEAT” appears.

2 Programme tracks (see step

3 on page 15).

3 Press u.

14

GB

Playing tracks in

random order (Shuffle Play)

You can play tracks in random order.

1 Press x.

“Cd” appears in the display.

2 Press MODE until “SHUF” appears in

the display.

3 Press u to start shuffle play.

To cancel Shuffle Play

Press MODE until “SHUF” disappears from

the display.

On the remote (CFD-E75/E75L/E77L

only)

Use N instead of u.

xu MODE

Playing tracks repeatedly

(Repeat Play) (continued)

To cancel Repeat Play

Press MODE until “REPEAT” disappears

from the display.

On the remote (CFD-E75/E75L/E77L

only)

• Use N instead of u.

• When you’ve selected “REPEAT 1”, select the

track by pressing the number buttons.

15

GB

The CD Player

1 Press x.

“Cd” appears in the display.

2 Press MODE until “PGM” appears in

the display.

3 Turn the jog dial to select the track you

want to programme, and press DSPL•

ENT MEM.

Repeat this step.

4 Press u to start programme play.

Creating your own

programme (Programme Play)

You can arrange the playing order of up to

20 tracks on a CD.

x

MODE

Jog dial u

DSPL

ENT MEM

On the remote (CFD-E75/E75L/E77L

only)

1 Press x.

2 Press MODE until “PGM” appears in the

display.

3 Press the number buttons for the tracks you want

to programme in the order you want.

4 Press N.

To cancel Programme Play

Press MODE until “PGM” disappears from

the display.

To check the order of tracks

before play

Press DSPL•ENT MEM.

Every time you press the button, the track

number appears in the programmed order.

To change the current

programme

Press x once if the CD is stopped and twice

if the CD is playing. The current programme

will be erased. Then create a new

programme following the programming

procedure.

Tips

• You can play the same programme again, since

the programme is saved until you open the CD

compartment.

• You can record your own programme. After

you’ve created the programme, insert a blank

tape and press z to start recording.

Programmed track Playing order

16

GB

The Radio

Presetting radio stations

You can store radio stations into the player’s

memory. You can preset up to 30 radio

stations (CFD-E75), 20 for FM and 10 for

AM in any order or 40 radio stations (CFD-

E70L/E75L/E77L), 20 for FM and 10 for

MW and LW in any order.

1 Press RADIO BAND•AUTO PRESET

to select the band.

2 Hold down RADIO BAND•AUTO

PRESET for 2 seconds until “AUTO”

appears in the display.

3 Press DSPL•ENT MEM.

The stations are stored in memory from

the lower frequencies to the higher

ones.

DSPL

ENT MEM

RADIO BAND

AUTO PRESET

Jog dial

If a station cannot be preset

automatically

You need to preset a station with a weak

signal manually.

1 Press RADIO BAND•AUTO PRESET to

select the band.

2 Tune in a station you want.

3 Hold down DSPL•ENT MEM for 2

seconds.

4 Select the preset number you want to

preset the new station on by turning the

jog dial.

5 Press DSPL•ENT MEM.

The new station replaces the old one.

On the remote (CFD-E75/E75L/E77L

only)

1 Press BAND until the band you want appears in

the display.

2 Press TUNE + or – until you tune in the station

you want.

3 Hold down the number button that you want to

preset the new station on for 2 seconds.

To select the preset number over 10, press >10

first, then the corresponding number buttons.

You need to hold down the last number button to

enter for about 2 seconds. (Example: To select

12, press >10 and 1 first, then hold down 2 for

about 2 seconds.)

The Radio

17

GB

Playing preset radio

stations

Once you've preset the stations, use the jog

dial on the player or the number buttons on

the remote to tune in to your favourite

stations.

1 Press RADIO BAND•AUTO PRESET

to select the band.

2 Turn the jog dial to tune in the stored

station.

On the remote (CFD-E75/E75L/E77L

only)

1 Press BAND until the band you want appears in

the display.

2 Press the number button to tune in a stored

station.

To tune in a preset station over 10, press >10

first, then the corresponding number buttons.

(Example: To tune in a preset station 12, press

>10 and 1 first , and then press 2.)

RADIO BAND

AUTO PRESET Jog dial

18

GB

The Audio Emphasis

Selecting the audio

emphasis (MEGA BASS)

You can adjust the audio emphasis of the

sound you are listening to.

Reinforcing the bass sound

Press MEGA BASS.

“MEGA BASS” appears in the display.

To return to normal sound, press the button

again.

MEGA BASS

The Timer

19

GB

Before you set the clock, connect the power

source (see page 24).

1 Press MENU•ALARM until “CLOCK”

appears in the display, then press

DSPL•ENT MEM.

The hour digit flashes.

2 Turn the jog dial to set the current hour.

Then press DSPL•ENT MEM.

The minute digits flash. Set the minutes

by turning the jog dial until the correct

minute is displayed.

The Timer

Setting the clock

“– –:– –” indication appears in the display

until you set the clock.

DSPL

ENT MEMJog dial

3 Press DSPL•ENT MEM.

The clock starts from 00 seconds.

Tip

The time display system:

CFD-E75: 12-hour system

CFD-E70L/E75L/E77L: 24-hour system

MENU

ALARM

20

GB

4 Set the timer to the hour you want the

music to start by turning the jog dial,

then press DSPL•ENT MEM.

Set the minutes, then press DSPL•ENT

MEM.

5 Set the timer to the hour and the

minutes you want the music to go off.

(Do as step 4.)

6 Turn the jog dial to set the volume, then

press DSPL•ENT MEM.

7 Press STANDBY.

The

indication lights up and the

power goes off.

At the preset time, the power will go on,

and the music will play. Then the power

will go off at the preset time, and the

player will enter into the standby mode.

To check/change when the

playback will start

Press MENU•ALARM until “TIMER”

appears in the display, then DSPL•ENT

MEM. Each time you press DSPL•ENT

MEM, a stored setting is displayed in the set

order. To change the setting, display the

setting you want to change and re-enter it.

Waking up to music

You can wake up to music or a radio

programme at a preset time. Make sure you

have set the clock (“Setting the clock” on

page 19).

Before you begin, make sure the

(clock)

indication is not lit in the display. If it is lit,

press STANDBY.

1 Prepare the music source you want to

play.

To play Do this

the radio Tune in a station.

a CD Insert a CD.

2 Press MENU•ALARM until “TIMER”

appears in the display, then press

DSPL•ENT MEM.

The

(clock) and the music source

(“Cd” or “RAdIO”) flash.

3 Select the music source (“Cd” or

“RAdIO”) by turning the jog dial, then

press DSPL•ENT MEM.

DSPL

ENT MEMJog dial

MENU

ALARM

STANDBY

Page is loading ...

Sony CFD-E77L User manual

This manual is also suitable for

Sony CFD-E77L User manual

in other languages

Related papers

Other documents