Sony CFD-E75 User manual

Category
Alarm clocks
Type
User manual

This manual is also suitable for

CD Radio
Cassette-Corder
3-228-965-33 (1)
© 2001 Sony Corporation
CFD-E70L
CFD-E75
CFD-E75L
CFD-E77L
Operating Instructions page 2
GB
Manual de instrucciones página 2
ES
GB
ES
2
GB
Warning
To prevent fire or shock hazard,
do not expose the player to rain
or moisture.
To avoid electrical shock, do not
open the cabinet. Refer
servicing to qualified personnel
only.
Information
For customers in Europe
This Compact Disc player is classified as a
CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT label is located
at the rear.
Warning
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
To prevent fire or shock hazard, do not place
objects filled with liquids, such as vases, on the
appliance.
Notice for customers in the United
Kingdom
A moulded plug complying with BS 1363 is fitted
to this equipment for your safety and convenience.
Should the fuse in the plug supplied need to be
replaced, same rating fuse approved by ASTA or
BSI to BS 1362, (i.e. marked with or mark)
must be used.
If the plug supplied with this equipment has a
detachable fuse cover, be sure to attach the fuse
cover after you change the fuse. Never use the
plug without the fuse cover. If you should lose the
fuse cover, please contact your nearest Sony
service station.
About this manual
The instructions in this manual are for the CFD-
E70L, CFD-E75, CFD-E75L and CFD-E77L.
Before you start reading, check your model
number. The CFD-E75L is the model used for
illustration purpose.
Note
The name of the switch to turn on/off this player is
indicated as below:
“OPERATE”: CFD-E70L/E75L/E77L
“POWER”: CFD-E75
Basic Operations
3
GB
Table of contents
Basic Operations
Playing a CD .................................................. 4
Listening to the radio...................................... 6
Playing a tape ................................................. 8
Recording on a tape ...................................... 10
The CD Player
Using the display .......................................... 12
Locating a specific point in a track .............. 12
Playing tracks repeatedly
(Repeat Play) ............................................ 13
Playing tracks in random order
(Shuffle Play) ........................................... 14
Creating your own programme
(Programme Play)..................................... 15
The Radio
Presetting radio stations................................ 16
Playing preset radio stations ......................... 17
The Audio Emphasis
Selecting the audio emphasis
(MEGA BASS)......................................... 18
The Timer
Setting the clock ........................................... 19
Waking up to music...................................... 20
Falling asleep to music ................................. 21
Using the countdown timer .......................... 22
Setting Up
Choosing the power sources ......................... 24
Additional Information
Precautions ................................................... 26
Troubleshooting............................................ 27
Maintenance ................................................. 30
Specifications ............................................... 31
Index ............................................................. 32
GB
4
GB
Connect the supplied mains lead (see page 24).
1 Press ZPUSH OPEN/CLOSE down
to open the CD compartment and
place the CD on the CD
compartment.
2 Close the lid of the CD compartment.
3 Press u (N on the remote, CFD-
E75/E75L/E77L only).
The player turns on (direct power-on)
and plays all the tracks once.
Basic Operations
3
Playing a CD
Display
With the label side up
1, 2
PUSH OPEN/CLOSE
PUSH OPEN/CLOSE
Playing timeTrack number
Basic Operations
5
GB
Use these buttons for additional operations
OPERATE
(or POWER)
x
u
Jog dial
VOLUME +, –
ZPUSH
OPEN/CLOSE
To Do this
adjust the volume Press VOLUME +, (VOL +, on
the remote, CFD-E75/E75L/E77L
only).
stop playback Press x.
pause playback Press u (X on the remote, CFD-
E75/E75L/E77L only).
Press the button again to resume
play after pause.
go to the next track Turn the jog dial clockwise.
(On the remote, press >, CFD-
E75/E75L/E77L only.)
go back to the previous track Turn the jog dial counterclockwise.
(On the remote, press ., CFD-
E75/E75L/E77L only.)
remove the CD Press ZPUSH OPEN/CLOSE.
turn on/off the player Press OPERATE (or POWER, see
page 2).
About CD-Rs/CD-RWs
This player is compatible with CD-Rs/CD-RWs but
playback capability may vary depending on the quality of
the disc, the recording device and application software.
6
GB
Listening to the radio
Connect the supplied mains lead (see page 24).
1 Press RADIO BANDAUTO
PRESET until the band you want
appears in the display (direct power-
on).
Each time you press the button, the
band changes as follows:
CFD-E75: FM t AM
CFD-E70L/E75L/E77L: FM t MW t LW
2 Hold down TUNE + or until the
frequency digits begin to change in
the display.
The player automatically scans the
radio frequencies and stops when it
finds a clear station.
If you can't tune in a station, press
the button repeatedly to change the
frequency step by step.
Display
Indicates an FM stereo
broadcast
12
RADIO
AUTO PRESET
BAND
TU
N
E
Basic Operations
7
GB
Use these buttons for additional operations
To Press
adjust the volume VOLUME +,
(VOL +, on the remote, CFD-E75/
E75L/E77L only)
turn on/off the radio OPERATE (or POWER, see page 2)
To improve broadcast reception
Reorient the aerial for FM. Reorient the player itself for
AM or MW/LW.
for FM for AM/MW/LW
Tips
If the FM broadcast is
noisy, press MODE until
Mono appears in the
display and the radio will
play in monaural.
If you need to change the
AM/MW tuning interval,
see page 25.
OPERATE
(or POWER)
VOLUME +, –
MODE
8
GB
Playing a tape
Connect the supplied mains lead (see page 24).
1 Press xZ to open the tape
compartment and insert a recorded
tape. Use TYPE I (normal) tape only.
Close the compartment.
2 Press n.
The player turns on (direct power-on)
and starts playing.
With the side you want
to play facing you
Display
21
Basic Operations
9
GB
Use these buttons for additional operations
To Press
adjust the volume VOLUME +,
(VOL +, on the remote, CFD-
E75/E75L/E77L only)
stop playback xZ
fast-forward or rewind the tape m or M
pause playback X
Press the button again to
resume play after pause.
eject the cassette xZ
turn on/off the player OPERATE (or POWER, see
page 2)
xZ
X
m, M
OPERATE
(or POWER)
VOLUME +, –
10
GB
Recording on a tape
Connect the supplied mains lead (see page 24).
1 Press xZ to open the tape
compartment and insert a blank tape.
Use TYPE I (normal) tape only.
2 Select the programme source you
want to record.
To record from the CD player, insert
a CD (see page 4) and press x on the
CD section.
To record from the radio, tune in the
station you want (see page 6).
3
With the side you want to
record on facing you
Display
1
RADIO
AUTO PRESET
BAND
Basic Operations
11
GB
3 Press z to start recording
(n is depressed automatically).
Use these buttons for additional operations
Tips
Adjusting the volume or the
audio emphasis (see page
18) will not affect the
recording level.
If the AM/MW/LW
programme makes a
whistling sound after you've
pressed z in step 3, press
MODE to select the
position of ISS
(Interference Suppress
Switch) that most decreases
the noise.
For the best results, use the
AC power as a power
source.
To erase a recording,
proceed as follows:
1 Insert the tape whose
recording you want to
erase.
2 Press X.
3 Press n.
4 Press z.
5 Press X.
xZ
X
OPERATE
(or POWER)
MODE
n
To Press
stop recording xZ
pause recording X
Press the button again to resume
recording.
turn on/off the player OPERATE (or POWER, see page 2)
12
GB
The CD Player
Using the display
You can check information about the CD
using the display.
Checking the remaining time
Press DSPLENT MEM while playing a CD.
To display
Press
DSPL
ENT MEM
the current track number once
and remaining time
on the current track*
the number of tracks left twice
and remaining time on the CD
the current track number three times
and playing time
* For a track whose number is more than 20, the
remaining time appears as “– : –”.
Total playing
time
Total track
number
DSPL
ENT MEM
Checking the total track
number and playing time
Press DSPLENT MEM in stop mode.
Locating a specific
point in a track
You can quickly find a specific point in
a track while playing a CD.
You can also locate any track on a CD using
the number buttons on the remote (CFD-
E75/E75L/E77L only).
To locate Press
a point while listening to M (forward) or m
the sound (backward) while
playing and hold down
until you find the point.
(On the remote, use
> or ., CFD-
E75/E75L/E77L only.)
a point while observing M (forward) or m
the display (backward) in pause
and hold down until
you find the point.
(On the remote, use
> or ., CFD-
E75/E75L/E77L only.)
a specific track directly the number button of
(CFD-E75/E75L/E77L the track.
only)
m M
13
GB
The CD Player
Playing tracks
repeatedly (Repeat Play)
You can play tracks repeatedly in normal,
shuffle or programme play modes (see pages
14 - 15).
1 Press x.
Cd appears in the display.
2 Proceed as follows.
To repeat
a single track
all the tracks
tracks in
random order
programmed
tracks
x
MODEJog dial
u
Note
You cannot locate a specific track if SHUF or
"PGM" is lit in the display. Turn off the indication
by pressing x (CFD-E75/E75L/E77L only).
Tip
When you locate a track numbered over 10, press
>10 first, then the corresponding number buttons.
Example:To play track number 23, press >10 first,
then 2 and 3 (CFD-E75/E75L/E77L only).
continued
Do this
1 Press MODE until
REPEAT 1 appears.
2 Turn the jog dial to select
the track that you want to
repeat.
3 Press u.
1 Press MODE until
REPEAT ALL appears.
2 Press u.
1 Press MODE until SHUF
REPEAT appears.
2 Press u.
1 Press MODE until PGM
REPEAT appears.
2 Programme tracks (see step
3 on page 15).
3 Press u.
14
GB
Playing tracks in
random order (Shuffle Play)
You can play tracks in random order.
1 Press x.
Cd appears in the display.
2 Press MODE until SHUF appears in
the display.
3 Press u to start shuffle play.
To cancel Shuffle Play
Press MODE until SHUF disappears from
the display.
On the remote (CFD-E75/E75L/E77L
only)
Use N instead of u.
xu MODE
Playing tracks repeatedly
(Repeat Play) (continued)
To cancel Repeat Play
Press MODE until REPEAT disappears
from the display.
On the remote (CFD-E75/E75L/E77L
only)
Use N instead of u.
When youve selected REPEAT 1, select the
track by pressing the number buttons.
15
GB
The CD Player
1 Press x.
Cd appears in the display.
2 Press MODE until PGM appears in
the display.
3 Turn the jog dial to select the track you
want to programme, and press DSPL
ENT MEM.
Repeat this step.
4 Press u to start programme play.
Creating your own
programme (Programme Play)
You can arrange the playing order of up to
20 tracks on a CD.
x
MODE
Jog dial u
DSPL
ENT MEM
On the remote (CFD-E75/E75L/E77L
only)
1 Press x.
2 Press MODE until PGM appears in the
display.
3 Press the number buttons for the tracks you want
to programme in the order you want.
4 Press N.
To cancel Programme Play
Press MODE until PGM disappears from
the display.
To check the order of tracks
before play
Press DSPLENT MEM.
Every time you press the button, the track
number appears in the programmed order.
To change the current
programme
Press x once if the CD is stopped and twice
if the CD is playing. The current programme
will be erased. Then create a new
programme following the programming
procedure.
Tips
You can play the same programme again, since
the programme is saved until you open the CD
compartment.
You can record your own programme. After
youve created the programme, insert a blank
tape and press z to start recording.
Programmed track Playing order
16
GB
The Radio
Presetting radio stations
You can store radio stations into the players
memory. You can preset up to 30 radio
stations (CFD-E75), 20 for FM and 10 for
AM in any order or 40 radio stations (CFD-
E70L/E75L/E77L), 20 for FM and 10 for
MW and LW in any order.
1 Press RADIO BANDAUTO PRESET
to select the band.
2 Hold down RADIO BANDAUTO
PRESET for 2 seconds until AUTO
appears in the display.
3 Press DSPLENT MEM.
The stations are stored in memory from
the lower frequencies to the higher
ones.
DSPL
ENT MEM
RADIO BAND
AUTO PRESET
Jog dial
If a station cannot be preset
automatically
You need to preset a station with a weak
signal manually.
1 Press RADIO BANDAUTO PRESET to
select the band.
2 Tune in a station you want.
3 Hold down DSPLENT MEM for 2
seconds.
4 Select the preset number you want to
preset the new station on by turning the
jog dial.
5 Press DSPLENT MEM.
The new station replaces the old one.
On the remote (CFD-E75/E75L/E77L
only)
1 Press BAND until the band you want appears in
the display.
2 Press TUNE + or until you tune in the station
you want.
3 Hold down the number button that you want to
preset the new station on for 2 seconds.
To select the preset number over 10, press >10
first, then the corresponding number buttons.
You need to hold down the last number button to
enter for about 2 seconds. (Example: To select
12, press >10 and 1 first, then hold down 2 for
about 2 seconds.)
The Radio
17
GB
Playing preset radio
stations
Once you've preset the stations, use the jog
dial on the player or the number buttons on
the remote to tune in to your favourite
stations.
1 Press RADIO BANDAUTO PRESET
to select the band.
2 Turn the jog dial to tune in the stored
station.
On the remote (CFD-E75/E75L/E77L
only)
1 Press BAND until the band you want appears in
the display.
2 Press the number button to tune in a stored
station.
To tune in a preset station over 10, press >10
first, then the corresponding number buttons.
(Example: To tune in a preset station 12, press
>10 and 1 first , and then press 2.)
RADIO BAND
AUTO PRESET Jog dial
18
GB
The Audio Emphasis
Selecting the audio
emphasis (MEGA BASS)
You can adjust the audio emphasis of the
sound you are listening to.
Reinforcing the bass sound
Press MEGA BASS.
MEGA BASS appears in the display.
To return to normal sound, press the button
again.
MEGA BASS
The Timer
19
GB
Before you set the clock, connect the power
source (see page 24).
1 Press MENUALARM until CLOCK
appears in the display, then press
DSPLENT MEM.
The hour digit flashes.
2 Turn the jog dial to set the current hour.
Then press DSPLENT MEM.
The minute digits flash. Set the minutes
by turning the jog dial until the correct
minute is displayed.
The Timer
Setting the clock
“– : –” indication appears in the display
until you set the clock.
DSPL
ENT MEMJog dial
3 Press DSPLENT MEM.
The clock starts from 00 seconds.
Tip
The time display system:
CFD-E75: 12-hour system
CFD-E70L/E75L/E77L: 24-hour system
MENU
ALARM
20
GB
4 Set the timer to the hour you want the
music to start by turning the jog dial,
then press DSPLENT MEM.
Set the minutes, then press DSPLENT
MEM.
5 Set the timer to the hour and the
minutes you want the music to go off.
(Do as step 4.)
6 Turn the jog dial to set the volume, then
press DSPLENT MEM.
7 Press STANDBY.
The
indication lights up and the
power goes off.
At the preset time, the power will go on,
and the music will play. Then the power
will go off at the preset time, and the
player will enter into the standby mode.
To check/change when the
playback will start
Press MENUALARM until TIMER
appears in the display, then DSPLENT
MEM. Each time you press DSPLENT
MEM, a stored setting is displayed in the set
order. To change the setting, display the
setting you want to change and re-enter it.
Waking up to music
You can wake up to music or a radio
programme at a preset time. Make sure you
have set the clock (Setting the clock on
page 19).
Before you begin, make sure the
(clock)
indication is not lit in the display. If it is lit,
press STANDBY.
1 Prepare the music source you want to
play.
To play Do this
the radio Tune in a station.
a CD Insert a CD.
2 Press MENUALARM until TIMER
appears in the display, then press
DSPLENT MEM.
The
(clock) and the music source
(Cd or RAdIO) flash.
3 Select the music source (Cd or
RAdIO) by turning the jog dial, then
press DSPLENT MEM.
DSPL
ENT MEMJog dial
MENU
ALARM
STANDBY
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

Sony CFD-E75 User manual

Category
Alarm clocks
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages