Kenmore 79031013600 Installation guide

Brand: Kenmore

Model: 79031013600

Category: Cookers

Type: Installation guide

This manual is also suitable for

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.

iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.

READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.

If the information in this manual is not followed exactly, a fire or explosion may result

causing property damage, personal injury or death.

FOR YOUR SAFETY:

-- Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor's phone.

Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or

the gas supplier.

Gas Cooktop

Dimensions

21/2"

30" Min.

(76.2 cm) _la

Gas Cooktop (6.4 cm)

Cutout Dimensions , ii

Figure 1

i_!_iiii__i_i_i_!iii!_i_i_¸i_!_i_!i_!_i_ii_i_!_!_i:i:i:i:i:i:iiiiiiiii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

30"GasCooktop 30 (76.2) 213A(55.2) 4_A(10.8) 27(68.6) 19 (48.3)

36"GasCooktop 36 (91.4) 213A(55.2) 4_A(10.8) 33_/4(84.5) 19(48.3)

30"GasCooktop 27Y4(69.2) 28_/2(72.4) 19_/8(48.6) 193A(50.2) 8 (20.3)

36"GasCooktop 337/8(86.1) 34_A(87) 19_/8(48.6) 193A(50.2) 8 (20.3)

All dimensions are stated in inches and (cm).

Dimension H includes a 5" (12.7 cm) space underneath the cooktop for connection to gas supply line.

NOTE: Wiring diagrams for this cooktop are enclosed in this booklet

Printed in United States

318201469 (0607) Rev.C

English - pages 1-9

Espar_ol- p_qginas10-18

Wiring Diagram 19-20

Important Notes to the Installer

I. Read all instructions contained in these installation

instructions before installing the cooktop.

2. Remove all packing material before connecting the

electrical supply to the cooktop.

3. Observe all governing codes and ordinances.

4. Be sure to leavethese instructions with the consumer.

5. Note: For operation at 2000 ft. elevations above see

level, appliance rating shall be reduced by 4 percent

for each additional 1000 ft.

Important Note to the Consumer

Keep these instructions with your Useand Care Guide for

future reference.

IMPORTANT SAFETY

INSTRUCTIONS

Installation of this cooktop must conform with local codes

or, in the absence of local codes, with the National Fuel

Gas Code ANSI Z223.1/NFPA 54 in the United States, or

in Canada, with the Canadian Fuel Gas Code, CAN/CGA

B149 and CAN/CGA B149.2.

When installed in a manufactured (mobile) home

installation must conform with the Manufactured Home

Construction and Safety Standard, title 24 CFR,part

3280 [Formerly the Federal Standard for Mobile Home

Construction and Safety, title 24, HUD (part 280)] or,

when such standard is not applicable, the Standard for

Manufactured Home Installation, ANSI/NCSBCS A225.1

or with local codes where applicable.

This cooktop has been design certified by CSA

International. As with any appliance using gas and

generating heat, there are certain safety precautions you

should follow. You will find them in the Use and Care

Guide, read it carefully.

• Be sure your cooktop is instaJJed and grounded

properly by a qualified installer or service

technician.

This cooktop must be electrically grounded in

accordance with local codes or, in their absence,

with the National ElectricaJ Code ANSI/NFPA No.

70--latest edition in the United States, or in

Canada, with the Canadian Electrical Code, CSA

C22.1 Part 1.

• The burners can be lit manually during an

electrical power outage. To light a burner, hold a

lit match to the burner head, then slowly turn the

Surface Control knob to MTE. Use caution when

lighting burners manually.

• Do not store items of interest to children in

cabinets above the cooktop. Children could be

seriously burned climbing on the cooktop to reach

items.

• To eliminate the need to reach over the surface

burners, cabinet storage space above the burners

should be avoided.

• Adjust surface burner flame size so it does not

extend beyond the edge of the cooking utensil

Excessive flame is hazardous.

• Never use your cooktop for warming or heating

the room. Prolonged use of the cooktop without

adequate ventilation can be hazardous.

• Do not store or use gasoline or other flammable

vapors and liquids near this or any other

appliance. Explosions or fires could result.

The electrical power to the cooktop

must be shut off while gas line connections are

being made. FaiJure to do so could resuJt in serious

injury or death.

13" (33 cm)

Max. Depth

For Cabinet

Installed Above

Cooktop.

18" Min,

(45.7 cm)

11/2"(3.8 cm)Minimum Distance

Between RearEdge of Cutout

and Nearest Combustible Surface

Above Countertop,

Clearance

30" (76.2 cm)

Min, Clearance

Between the

Top of the

Cooking

Platform and

Unprotected

Wood or Metal

Cabinet

24" cm)

_To eliminate the risk of

burns or fire from reaching over heated

surfaces, cabinet storage space located

above the cooktop should be avoided. If

cabinet storage is provided, risk can be

reduced by installing a range hood that

projects horizontally a minimum of 5"

(12.7 cm) beyond the bottom of the

cabinets.

Drawers Cannot Be Used with This

Cooktop Since Burner Box Extends

3s/32'' (8.02 cm) Below Surface of

Countertop.

30'_Cooktop 30'_(76.2 cm) 7'_(17.8 cm)

36'_Cooktop 36'_(91.4 cm) 7'_(17.8 cm)

7"(17.8 cm)

Figure 2 - CABINET DESIGN

Typical Gas Cooktop Installation Over

an Electric Built-in Oven Installed Under the Counter

Wall

Manifold Pi

Flexible Connector

Oven Cabinet

I_---- 18" (45.7 cm) Max.-----_

Cabinet sidesor

filler panel

61_2"

5" ,(16.5 cm)

Flare (12.7cm) Min.

Union

_J Flare

_j Union

120V/60Hz

Grounded

Outlet

Pressure

Regulator

4" (10.2 cm)

Right Side of

Cabinet

Manual Shutoff Valve

(To be accessible for

shut-off valve opera-

tion)

Typical Under Counter Installation of an Electric Built-in

Oven with a Cooktop Mounted Above

All mounting hardware

must be used to secure

the built-in oven to the

cabinets. Refer to the

built-in oven installa-

tion instructions.

Junction box must

be located approx.

3" to the left of

the built-in oven

cutout,

208/240 Volt grounded junction

box for built-in

This cooktop may

be installed over

certain built-in elec-

tric oven models.

Side filler panels are necessary to

isolate the unit from adjoining

cabinets. Panel height should allow

for installation of approved cooktop

models. See "Typical Gas Cooktop

Installation Over an ElectricBuilt-in

Oven Installed Under the Counter"

on previous page.

32" Min.**

(81.3 cm)

36"

(91.4 cm)

Use 3/4" (1.9 cm) plywood, installed

on two runners, flush with toe plate.

Must be capable of supporting 150 Ibs.

Cut an opening in wood base minimum 9"

(22.9 cm) x 9" (22.9 cm), 2" (5.1 cm) from

left side filler panel, to route armoured

cable to junction box.

4 1/2" (11.4 cm)

Max.*

* If no cooktop is installed directly

over the oven unit, 5" (12.7 cm)

maximum is allowed.

** 32" (81.3 cm) min. from top of

cabinet to top of runners must be

maintained.

CUTOUT DIMENSIONS (inches)

OVEN SIZE E F G

Min. Max, Min. Max.

30" 27¼" 28s/8 '' 281/2" 29" 231/2"

(76.2 cm) (69.2 cm) - (72.7 cm) (72.4cm) - (73.7 cm) (59.7 cm)

27" 27¼" 28s/8 '' 247/8 '' 25¼" 231/2"

(68.6cm) (69.2cm) - (72.7cm) (63.1cm) (64.1cm) (59.7cm)

Wall Outlet Location

12"_

10"

Recommended area for

12OV grounded outlet

on rear wall.

_.._F UEN_T 22"

: NOTE: If an outlet

I is not available,

have one installed by

i a qualified technician. _,

OF UNIT

Figure 3

Cooktop Installation

1. Visually inspect the cooktop for damage.

2. Set the cooktop into the countertop cutout.

To clamp down, insert an angle bracket into the slot on

each side of the unit as shown.Run thumb screw up

through the bracket, up against the bottom of the

counter. Tighten until the unit draws down and issecure.

Provide an Adequate Gas Supply

This cooktop isdesigned to operate on natural gas at 4"

of manifold pressure only.

A pressure regulator is connected in series with the

manifold on the cooktop and must remain in series with

the supply line.

For proper operation, the maximum inlet pressure to

the regulator must be no more than 14" of water column

(W.C.) pressure.

For checking the regulator, the inlet pressure must be at

least 1" (or 2.5 kPa) greater than the regulator manifold

pressure setting. The regulator is set for 4" of manifold

pressure, the inlet pressure must be at least 5".

The gas supply line to the range should be I/2" or 3/4"

pipe.

LP/Propane Gas Conversion

This appliance can be used with Natural gas or LP/

Propane gas. It is shipped from the factory for use with

natural gas.

A kit for converting to LPgas is supplied with your

cooktop. The kit is marked "FOR LP/PROPANEGAS

CONVERSION".

NOTE: Do not use caulking compound; cooktop should

be removable for service when needed.

Clamp Down Information

Once the cooktop is installed in the counter opening, you

must clamp the unit down as shown.

Countertop

Cooktop _ t

, _ _ ,

Angle ......__Ll_

Bracket_

_ Thumb

Screw

Figure 4

The conversion must be performed by a qualified service

technician in accordance with the kit instructions and all

local codes and requirements. Failure to follow

instructions could result in serious injury or property

damage. The qualified agency performing this work

assumes responsibility for the conversion.

Failure to make the appropriate

conversion can result in serious personal injury and

property damage.

Important: Removeallpackingmaterialand

literaturefromcooktopbeforeconnectinggasand

electricalsupplytocooktop.

Install Pressure Regulator

Install the pressure regulator with the arrow on the

regulator pointing up toward the unit in a position where

you can reach the access cap.

Do not make the connection too tight.

The regulator is die cast. Overtightening may crack the

regulator resulting in a gas leak and possible fire or

explosion.

Shutoff Valve =

Open position

Figure 6

Manual GAS FLOW Pressure

Shutoff Flare _'_ Flare Regulator

Valve Union Union _,

Nipple Flexible Access

Off Connector

Cap

All connections must be wrench-tightened

Figure 5

Assemble the flexible connector from the gas supply pipe

to the pressure regulator in the following order:

I. manual shutoff valve

2. I/2" (1.3 cm) nipple

3. 1/2" (1.3 cm) flare union adapter

4. flexible connector

5. I/2" (1.3 cm) flare union adapter

6. 1/2" (1.3 cm) nipple

7. pressure regulator

Use pipe-joint compound made for use with Natural and

LP/Propane gas to seal all gas connections. If flexible

connectors are used, be certain connectors are not

kinked.

The supply line must be equipped with an approved

manual shutoff valve. This valve should be located in the

same room as the cooktop and should be in a location

that allows ease of opening and closing. Do not block

access to the shutoff valve. The valve is for turning on or

shutting off gas to the appliance.

Once regulator is in place, open the shutoff valve in the

gas supply line. Wait a few minutes for gas to move

through the gas line.

Check for leaks. After connecting the cooktop to the

gas supply, check the system for leaks with a

manometer. If a manometer is not available, turn on the

gas supply and use a liquid leak detector (or soap and

water) at all joints and connections to check for leaks.

Do not use a flame to check for leaks

from gas connections. Checking for leaks with a flame

may result in a fire or explosion.

Tighten all connections if necessary to prevent gas

leakage in the cooktop or supply line.

Check alignment of control knob valves after

connecting the cooktop to the gas supply to be sure the

cooktop manifold pipe has not moved. A misalignment

could cause the valve stems to rub on the control panel,

resulting in a gas leak at the valve.

Disconnect this cooktop and its individual manual

shutoff valve from the gas supply piping system during

any pressure testing of that system at test pressures

greater than I/2 psig (3.5 kPa or 14"water column).

Isolate the cooktop from the gas supply piping

system by closing its individual manual shutoff valve

during any pressure testing of the gas supply piping

system at test pressures equal to or less than I/2 psig

(3.5 kPa or 14" water column).

Electrical Requirements

120 volt, 60 Hertz, properly grounded branch circuit

protected by a 15 amp circuit breaker or time delay fuse.

Do not use an extension cord with this cooktop.

Grounding Instructions

iMPORTANT Please read carefully.

For personal safety, this appliance must be properly

grounded.

The power cord of this appliance isequipped with a 3-

prong (grounding) plug which mates with astandard 3-

prong grounding wall receptacle (see Figure 7) to

minimize the possibility of electric shock hazard from the

appliance.

The wall receptacle and circuit should be checked by a

qualified electrician to make sure the receptacle is

properly grounded.

Preferred Method

Grounding type

wall receptacle

not, under any_'_

circumstances, cut, I

remove, or bypass I

the grounding )

_rong. J

C. Place a burner cap on each burner head, matching

the cap size to the head size. Each burner cap has an

inner locating ring which centers the cap correctly on

the burner head.

D. Besure that all the burner caps and burner heads are

correctly placed BEFOREusing your cooktop.

NOTE: There are no burner adjustments necessary on

this cooktop.

Power supply cord with 3-

prong grounding plug.

Figure 7

Where a standard 2-prong wall receptacle is installed, it

is the personal responsibility and obligation of the

consumer to have it replaced by a properly grounded 3-

prong wall receptacle.

Do not, under any circumstances, cut or remove the

third (ground) prong from the power cord.

Disconnect electrical supply cord from

wall receptacle before servicing cooktop.

Check Operation

Refer to the Use and Care Guide packaged with the

cooktop for operating instructions and for care and

cleaning of your cooktop.

Do not touch the burners. They may be hot enough to

cause burns.

1. Install Burner Caps

This cooktop is equipped with sealed burners as shown

(see Figure 8).

A. Unpack your burner heads and burner caps.

B. Place burner head over each gas orifice, matching the

head with the orifice size. Be careful not to damage

the electrode while placing the head over the

orifice. Make sure electrode fits correctly into slot in

burner head.

Burner Head

Gas Opening

Figure 8

2. Turn on Electrical Power and Open Main Shutoff

Gas Valve

3. Check the Igniters

Operation of electric igniters should be checked after

cooktop and supply line connectors have been carefully

checked for leaks and the cooktop has been connected

to electric power.

To operate the surface burner:

A. Push in and turn asurface burner knob to the LITE

position. You will hear a small ticking noise; this is

the sound of the electric ignitor which lights the

burner.

B. After the burner lights, turn to the desired flame size.

The controls do not have to be set at a particular

mark. Use the marks as a guide and adjust the flame

as needed.

4.Adjustthe"low" setting for regular surface burner

valves(Figure9)

a. Push in and turn control to LITEuntil burner ignites.

b. Quickly turn knob to LOWEST POSITION.

c. If burner goes out, reset control to OFF.

d. Remove the surface burner control knob.

e. Insert a thin-bladed screwdriver into the hollow valve

stem and engage the slotted screw inside. Flame size

can be increased or decreased with the turn of the

screw. Turn counterclockwise to increase flame size.

Turn clockwise to decrease flame size. Adjust flame

until you can quickly turn knob from LITEto LOWEST

POSITIONwithout extinguishing the flame. Flame

should be as small as possible without going out.

Note: Air mixture adjustment is not required on surface

burners.

[__II_ Clockwise

Counter clo_

5. Adjust the "LOW" Setting of the Bridge Burner

Surface Valve (Figure 9) (some models):

Note: On the dual valve the low setting of each portion

(rear portion of bridge burner and the center portion of

bridge burner) should be adjusted individually.

a. Push in and turn control to LITEuntil the rear )ortion

of the bridge burner ignites only.

b. Quickly turn knob to LOWEST POSITION.

c. If burner goes out, reset control to OFF.

d. Remove the surface burner control knob.

e. The rear portion of the bridge burner flame size can

be increased or decreased with the turn of the screw

A. Use screw B to adjust the flame size of the center

portion of the bridge burner. Turn counterclockwise

the screw to increase flame size. Turn clockwise the

screw to decrease flame size. Adjust flame until you

can quickly turn knob from LITEto LOWEST POSITION

without extinguishing the flame. Flame should be as

small as possible without going out.

Note: Air mixture adjustment isnot required on surface

burners.

When All Hookups are Complete

Make sure all controls are left in the OFFposition.

Make sure the flow of combustion and ventilation air to

the cooktop isunobstructed.

Regular

Burner

Valve

Hollow

Valve

Stem

Figure 9

Model and Serial Number Location

The serial plate is located on the underside of the

cooktop.

When ordering parts for or making inquires about your

range, always be sure to include the model and serial

numbers and a lot number or letter from the serial plate

of your cooktop.

Your serial plate also tells you the rating of the burners,

the type of fuel and the pressure the cooktop was

adjusted for when it left the factory.

Burner

Valve

Before You Call for Service

Read the Before You Call for Service Checklist and

operating instructions in your Use and Care Guide. It

may save you time and expense. The list includes

common occurrences that are not the result of defective

workmanship or materials in this appliance.

Refer to your Use and Care Guide for Sears service

phone numbers, or call 1-800-4-MY-HOME ®.

Page is loading ...

TOP Bb_NER LGNI TER

OPT [ ONAL

OLJEMADOR DE E'\OEND DO SUPERIOR

DPC I ONAL

_:)UG IE D' ALLb,_AGE BRL_ EUR

TOP BUF;I_:ER iGNITER

OPT / ONAI

OUEMAF>OR DE ENCENOIDU BUrR/OR

OPCIO_

B0bO I E D" ALLUHADE-Bia_t.EUR

FACULTAT I F

IGNITER MODULE BOARD

CUADRO DE MODULO DE ENCENDIO0

N ALLLMEUR

L @

o @

DISCONNECT POWER BEFORE SERVICING UNT

DESCONECTE LA ENEF_GIA ANTES DE _EALIZAR

EL MANTENIMIENIO DEL ELEC-RODOP_STIEO

AVERT ISEMENT

_URANT AVANT D'EFFECTDER LA

F#EPARA T]ON

COLOR CODE / COD DOS DE C_.OR / CODE CO_EUR

B_BLACK / NEGRO / NO_R

_ITE / RANBO / _AT',O

RIGHT REAR

I[ IGNSW

J [ IN]E_:TRASERO

i [ OERFCP_

i [ INTERALLUM

II OAR

i i LEFT REAR

i [

i _ lGN SW

I [ I NT ENC TRASERO

i IZO_ IERDO

4[ r ]NTER ALLU'M

G AR

LEFT FRONT

LGN SW

[NTENC DE

FRENTE IZOU[ER]O

LNTERALLU_

G AV

I [ RIOCT FRONT

I I I G\ SW

i i ]NT. ENC _-

I I FRENTE DERECHO

II INTER AUL_

D AV

DuNMocs

EMPALME

C(tNNECTEUR

GROUND

PDESTA A TIERRA

MBE A LA TERRE

POWER CORD

PARA TRANSPORTE

DE YUFRZA

CA_E

O' ALI NENTAT I ON

2 18 200

I 20 150

_]RE GAGE

ALAMBRE MEDiOA TEMP'C

FJL CAL

3304

3321

UL STYLE

MOOD UL

STYLE UL

iL]

CAUTION:

LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS

_IRIM] E_OR CAN CAbbiE [_R{_ER A_ DANGEWOb<_ OPTRATION

VERIFY PROPER ORERA_]_ AFTER DERVICIKG

AVISO:

ETIOL_TE TO_S LOS ALAMBRES ANTES DE DESCOWEC_AR PAR

REALIZAR ET MANTENIM[ENTO EE LOS CGqTROLES. ERROR DE

ALAHO_A._ PJDEDU CAUSAR UN FUNCIONAM]ENTO [NCOF_ECTO

Y PEL]GROSOVER[ODE BI EL FUNC/ONAM]ENTO ESTA

CORREOTO OESPbES [:)ELMANTENIMIENTO

AVER]ISSEMENT:

ETIOLETER CHA_JE FIL AVANT LE DEBRANCFEMENT DE CEUX-CiUNE ERREUR DE

8RANCHEMENT PEUT CAbSER UNE OPERATION DANDEREUSEVERIFLER LE BeN

FONCTIONNEMENT DE L'A;:>PAREIL APRES TOUTE REPARATION

RIGHT FRONT _EFT FRONT

]GNSW iGNSW

]NT ENC DE iNTENC DE

_RENTE DEREGHC FRFJNTE IZOU_ERO0

INTERALLUM INTERALLUM

DAV GAV

TOP _RNER IGNITER

G_EM_OR DE E_ENOIDO SUPERI_

BOUGIE D'ALLUMADE-BRULEUR _

TOP C:_JRNER IGNITER

DUEHADOR DE ENCENDIDU Bb_BRIOR

BOUGiE D'ALLUMADE-BRULEUR _

TOP BURNER iGNITER

OUEMA[2OR DE ENCEND_DO SUPERIOR

BOOGIE D'ALLUMAOS-BRCEEUR _

TOP _:_JRNfR IGNITER

CEJE"[AOO'_DE ENCENDIDO SL_ER}OR

BOUGIE D" ALLUMAGE-BRULEDR

LEFT REAR RIGHT REAR

IGNS_ ION SW

INTENCTRASERO ]N]ENC[RABERO

IZOUIERO0 BERECHO

]NTERA_LUM INTERALLUM

GAR OAR

O 0 N©

I 318047111

IGNITER MODULE BOARD

CUADRO DE MODULO DE ENOENDIOO

BLOC CONNECTION ALLUHEUR

REV. B

C;_ [3LJ_N R ]ON ER

Ob_',IDS_ OF NC [XU]DO UPROR

I_JGiE rl'R[ LLJ_AGE E_RtJl EUR

OP 8LRN V: ](} ER

0 JE'_ADC ':_, D£ EN(}_NI}I}O SUPE OI

BOtJQ J E D' £L -U'_AGE 8LJL ER

.'}1 U_N]R ] (}fl ] ][R

QUEM_DQR DE ENC NOJDQ ,U° [ [OR

BOUG E D" _LLU_&G RULEU_

}iR

TOP BURN QN I TER

i!iOU(}iE D" AIJ UMAGE B_Ui I!iLJR

IJ TE _4}{}k }::_D

C _:DRO DE IOOLO D ENCN DO

BiOC CONNECTION _°:_ _'_'_

U'A_N [ NG

O ! C(}NN CT i:s(},i ]F_ cl FO_] rE N3 LN

A,,, ISO

DESCONEC/_ i ,s _NER(} I _ AN IES DE i_EAL i ZAi_

EL _AN[ENiMiEN/O OEt ELECT_ODOHi_STJCO

DiSCONN_CF POWER DEFO[_E 5EF_v[C[NO UN[ {

AvER T 155EMEN f

_EP&RAT ION

QqT R A_

] G\ S_,,'

]NT NC TR%S RO

OERECI i()

] NTE_ AL I U_

_4 R4

R_ R4

FRENTE ]Z0 JERDO

[ [R At i LM

0 A,i

GI] RON]

]ON 5,,,

NT [N( {}!

FRENT GERCO

I NE_ t <

DAV

( NIIRi IRi\_

QN S,,

N EN.'} ( NTRO

RAERO

_1 J

C aR

I}()NN C O

_FAL IE

30NNECTEUR

GROUND

I'IISE % LA TERRE

DE FUEF_Z_

C_B_ E

4 20 i50 C j 338

8 200 C J 3304 ;i< [!_I _'CK / [OR() / N',}IR

S PO0" ¢"

_ i _ WJi]iE / BL_NCO / BLANC

_iRE IG¸i_¸G_ I Ut S!Yi E I L)R } )E / O) G)£ D L R /

i ¸I _ " _ ....... c/ %' _ i" COuE uOULLU_

CAUT ION;

I,q_" A _,1 _11 [ I<(_N (F_ 'IN _F/v (IN ( NI[!( %

,,, N( El Oi £N (At3 Hi '}(1_ _ND ):NG lOtS O1 R_ (N

,/ R[: _ROPEI Of IAT [ON _[

AVISO:

E r J(} ET ]ODOr; 10 _-GblJl:_bb AN[ E D D -/ON C],_R I: ;d:_

R/[ Z_IR I"ANENI [ N( _; LO UON]R£ S R()R D

_ _cN IA. ILl C,_J_A_ LN UN( 1.2\qbl N]O NCORRFC[O

Y _ GROt40 V R (kE SI EL UNCIO\AH N]O ES/A

(()4_ (]O }E%F J _ I viNf N M iXT)

AVERT IS_NENT :

E IO{;ETER CHAOL_ FIL AVAN- i_ OEBRANCI_ENEN- DE EEUX C] UNt ERRtLJ_ DE

BF_ANCI_ENI ¸ I_EUi¸ CAUSER UN _ OPE_]iON D_NGE _LUSE VEIR[F i_l_ LE BEN

FONCiiO\_\tNENI DE L'APPAREII AP_-5 OUTE RE_A_A iON

CEN E M_AR RIG}[ FF/ON] E / iRON] LE_ RFAR R](}k [ RFAR

IN] ENE CEN/!RO [Ni ENC DE I NT E_ D_ IN] ENC iRASERO [NT ENC _RASERO

]NiE_ A_{ UN [N[hN _Ii i U_ INiE_ Ai L U_ ]NIER RL! iJM [NI_R AL t U_

[ i

OP 8JRN IGN] TER

(]UI V!DO[ 3E INC N9i[ 3JP[I: (

B(k(}IE l'_t kJ _ E I:iJt ELJIR

rOTE :

{ _,'IC : I} qCEMN] OF ]i,d INA } I {COME N CE q:_,Y COb{! Risi; { ,_ ql YP[ _\N[}

(_(} (NO (}()lSA al R ]N4i IUS] B USI}

NO ]A

IN EASO {;( ]8_ \[{E!AF!IO I}E IE H{ qZg_ 0{ IORNE E NEE{{SA[( O I)E UTII ZAR

E F/ISO TRO DE "[4VR Y D ['_ DIDOR Y [ SF/O TJPO D sORNES

10 F

SE '_ICE:SI DES F: ILS Od ES COSSES DO],/ENI FIRE RE{4PL_CES, U] [L SEZ DES PIECES

DE C'_LIB_E El DE [?:ES EQUI'/&LEN S

3180471 12 REV. A

Kenmore 79031013600 Installation guide

Brand: Kenmore

Model: 79031013600

Category: Cookers

Type: Installation guide

This manual is also suitable for

Download PDF

report

in other languages

español: Kenmore 79031013600 Guía de instalación

Kenmore 79031013600 Installation guide

This manual is also suitable for

Kenmore 79031013600 Installation guide

in other languages

Related papers

Other documents