Infocus H 55SC User manual

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce

produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs et propriétaires

avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être conservé dans un

endroit sûr.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool. This manual should

be stored in safe place.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede

resultar en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este

manual debe ser guardado en un lugar seguro.

H 55SC

Model Demolition Hammer

Modèle Marteau de demolition

Modelo Martillo demoledor

01Eng_H55SC_US 7/6/07, 10:461

Page is loading ...

English

3

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in

the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs, and by observing appropriate

safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual

and in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by

WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by

HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in

death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in

minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

01Eng_H55SC_US 7/6/07, 10:463

English

4

SAFETY

GENERAL SAFETY RULES

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric shock,

fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

(2) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the

dust of fumes.

(3) Keep bystanders children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical Safety

(1) Double Insulated tools are equipped with a polarized plug (one blade is wider than

the other.) This plug will fit in a polarized outlet only one way. If the plug does not

fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified

electrician to install a polarized outlet. Do not change the plug in any way. Double

Insulation

eliminates the need for the three wire grounded power cord and

grounded power supply system.

(2) Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is grounded.

(3) Do not expose power tools to rain or wet conditions. Water entering a power tool

will increase the risk of electric shock.

(4) Do not abuse the cord. Never use the cord to carry the tools or pull the plug from

a receptacle. Keep cord away from heat, oil, sharp edges or moving parts. Replace

damaged cords immediately. Damaged cords increase the risk of electric shock.

(5) When operating a power tool outside, use an outdoor extension cord marked “W-

A” or “W”. These cords are rated for outdoor use and reduce the risk of electric

shock.

3. Personal Safety

(1) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tires or under the influence of drugs, alcohol,

or medication. A moment of inattention while operating power tools may result in

serious personal injury.

(2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep

your hair, clothing and gloves away from moving parts. Loose clothes, jewelry, or

long hair can be caught in moving parts.

(3) Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools

with your finger on the switch or plugging in tools that have the switch on invites

accidents.

01Eng_H55SC_US 7/6/07, 10:464

English

5

(4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key

that is left attached to a rotating part of the tool may result in personal injury.

(5) Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control of the tool in unexpected situations.

(6) Use safety equipment. Always wear eye protection. Dust mask, non-skid safety

shoes, hard hat, or hearing protection must be used for appropriate conditions.

4. Tool Use and Care

(1) Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead

to loss of control.

(2) Do not force tool. Use the correct tool for your application. The correct tool will do

the job better and safer at the rate for which it is designed.

(3) Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

(4) Disconnect the plug form the power source before making any adjustments,

changing accessories, or storing the tool. Such preventive safety measures reduce

the risk of starting the tool accidentally.

(5) Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

(6) Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

(7) Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tool's operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

(8) Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used

with another tool.

5. Service

(1) Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

(2) When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to

follow Maintenance Instruction may create a risk of electric shock or injury.

01Eng_H55SC_US 7/6/07, 10:465

English

6

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will

make exposed metal parts of the tool “live” and shock the operator.

2. ALWAYS wear ear protectors when using the tool for extended periods.

Prolonged exposure to high intensity noise can cause hearing loss.

3. NEVER touch the tool bit with bare hands after operation.

4. ALWAYS attach the side handle and securely grip the Demolition Hammer.

5. NEVER touch moving parts.

NEVER place your hands, fingers or other body parts near the tool’s moving parts.

6. NEVER operate without all guards in place.

NEVER operate this tool without all guards or safety features in place and in proper

working order. If maintenance or servicing requires the removal of a guard or safety

feature, be sure to replace the guard or safety feature before resuming operation of the

tool.

7. Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended —for example— don’t use circular saw for

cutting tree limbs or logs.

8. NEVER use a power tool for applications other than those specified.

NEVER use a power tool for applications other than those specified in the Instruction

Manual.

9. Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not drop or throw

the tool. NEVER allow the tool to be operated by children, individuals unfamiliar with

its operation or unauthorized personnel.

10. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.

11. Do not use power tools if the plastic housing or handle is cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not

be used until repaired.

12. Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to yourself or others. Blades, cutting implements and

accessories which have been mounted to the tool should be secure and tight.

13. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so that air can freely flow at all times.

Check for dust build-up frequently.

01Eng_H55SC_US 7/6/07, 10:466

English

7

14. Operate power tools at the rated voltage.

Operate the power tool at voltages specified on its nameplate.

If using the power tool at a higher voltage than the rated voltage, it will result in

abnormally fast motor revolution and may damage the unit and the motor may burn

out.

15. NEVER use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange for repairs by a Hitachi

authorized service center.

16. NEVER leave tool running unattended. Turn power off.

Don’t leave tool until it comes to a complete stop.

17. Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently, it may

be deformed, cracked, or damaged.

18. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may

damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

19. ALWAYS wear eye protection that meets the requirement of the latest revision of ANSI

Standard Z87.1.

20. ALWAYS be careful with buried object such as an underground wiring.

Touching live wiring or electric cable with this tool may result in electric shock.

Confirm before use whether hidden objects are present, such as electric cables within

the wall, floor or ceiling.

21. Definitions for symbols used on this tool

V ............ volts

Hz .......... hertz

A ............ amperes

no ..........no load speed

W ........... watt

.......... Class II Construction

---/min ... revolutions per minute

.......... Alternating current

01Eng_H55SC_US 7/6/07, 10:467

English

8

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation

design. “Double insulation” means that two physically separated insulation systems have

been used to insulate the electrically conductive materials connected to the power supply

from the outer frame handled by the operator. Therefore, either the symbol “

” or the

words “Double insulation” appear on the power tool or on the nameplate.

Although this system has no external grounding, you must still follow the normal electrical

safety precautions given in this Instruction Manual, including not using the power tool in

wet environments.

To keep the double insulation system effective, follow these precautions:

䡬 Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this

power tool, and only genuine HITACHI replacement parts should be installed.

䡬 Clean the exterior of the power tool only with a soft cloth moistened with soapy water,

and dry thoroughly.

Never use solvents, gasoline or thinners on plastic components; otherwise the plastic

may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

01Eng_H55SC_US 7/6/07, 10:468

English

9

FUNCTIONAL DESCRIPTION

NOTE: The information contained in this Instruction Manual is designed to assist you in

the safe operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read

and understood all safety instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that

differ from those on your own power tool.

NAME OF PARTS

SPECIFICATIONS

Fig. 1

Housing

Tool holder

Front cover

Nameplate

Cap cover

Set screw

Switch trigger

Brush cap

(under the cap cover)

Motor Single-Phase, Series Commutator Motor.

Power Source Single-Phase, 120 V AC 60 Hz

Current 10 A

Full-load Impact Rate 1,450/min.

Weight 40.3 lbs (18.3 kg)

D-type side handle

This power tool has anti vibration handles.

The handles reduce vibration which is added to the operator.

01Eng_H55SC_US 7/6/07, 10:469

English

10

ASSEMBLY AND OPERATION

APPLICATIONS

䡬 Breaking concrete, chipping off concrete, grooving, bar cutting, and driving piles.

(Application examples)

Installation of piping and wiring, sanitary facility installation, machinery installation,

water supply and drainage work, interior jobs, harbor facilities and other civil engineering

work.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the power source requirements

specified on the product nameplate.

2. Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a receptacle

while the switch is in the ON position, the power tool will start operating immediately

and can cause serious injury.

3. Extension cord

When the work area is far away from the power source, use an extension cord of

sufficient thickness and rated capacity. The extension cord should be kept as short as

practicable.

WARNING:

Damaged cord must be replaced or repaired.

4. Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact

a licensed electrician to make appropriate repairs.

If such a faulty receptacle is used, it may cause overheating, resulting in a serious

hazard.

5. Confirming condition of the environment:

Confirm that the work site is placed under appropriate conditions conforming to

prescribed precautions.

01Eng_H55SC_US 7/6/07, 10:4610

English

11

6. How to install tool

CAUTION:

For tools such as a bull point and a cold chisel,

use only Hitachi genuine parts.

(1) Clean, then smear the tool shank with the

grease provided.

(2) Slide the tool holder in the direction of arrow

A and rotate it 180˚.

Turn the notch of the tool shank downward and

insert it fully into the hexagonal hole of the

front cover. (Fig. 2)

(3) Turn the tool holder and align the front cover

mark with the tool holder mark to secure.

NOTE: Remove in the reverse order to

installation.

HOW TO USE THE DEMOLITION HAMMER

1. After placing the tip of the tool in the base hole,

switch ON.

2. By utilizing the empty weight of the machine

and firmly hold the hammer with both hands,

you can effectively control the subsequent

recoil motion. Proceed at a moderate work-

rate, applying too much force will impair

efficiency.

Fig. 2

Tool holder

Tool shank

Front cover

A

Fig. 3

01Eng_H55SC_US 7/6/07, 10:4611

English

12

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the

receptacle during maintenance and inspection.

1. Inspecting the tool

Since use of a dull tool will degrade efficiency and cause possible motor malfunction,

sharpen or replace the tool as soon as abrasion is noted.

2. Inspecting the screws

Regularly inspect all screws and ensure that they are properly tightened. Should any of

the screws be loose, retighten them immediately.

WARNING: Using this Demolition Hammer with loosen screws is extremely

dangerous.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power tool. Exercise due care to

ensure the winding does not become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes: (Fig. 4)

The motor employs carbon brushes which are consumable parts. When they become

worn to or near “wear limit”, it could result in motor trouble. When an auto-stop carbon

brush is equipped, the motor will stop automatically. At that time, replace both carbon

brushes with new ones which have the same carbon brush Nos. shown in the figure.

In addition, always keep carbon brushes clean and ensure that they slide freely within

the brush holders.

CAUTION:

Using this Demolition Hammer with a carbon brush which is worn in excess of the

wear limit will damage the motor.

Fig. 4

NOTE: Use HITACHI carbon brush No. 71 indicated in Fig. 4

Wear limit

No. of carbon brush

0.28" (7 mm)

0.67" (17 mm)

71

01Eng_H55SC_US 7/6/07, 10:4612

English

13

䡬 Replacing carbon brushes:

(For parts name, refer to Fig. 1)

Loosen the set screw then remove the cap cover. Remove the brush cap and carbon

brush. After replacing the carbon brush, do not forget to tighten the brush cap securely

and to install the cap cover.

5. How to replace grease

This machine is full air-tight construction to protect against dust and to prevent lubricant

leakage. Therefore, the machine can be used without lubrication for long periods.

Replace the grease as described below.

䡬 Grease replacement period

After purchase, replace grease after every 6 months of usage. Ask for grease replacement

at the nearest HITACHI Authorized Service Center. Proceed for replacement of grease.

䡬 Grease replenishment

CAUTION:

Before replenishing the grease, turn the power off and pull out the power plug.

(1) Remove the crank cover and wipe off the

grease inside. (Fig. 5)

(2) Apply 1.1 oz (30 g) of HITACHI Electric Hammer

Grease A (optional accessory, contained in

tube) to the crank case.

(3) After replenishing the grease, install the crank

cover securely.

NOTE: The HITACHI Electric Hammer Grease

A is of the lower viscosity type. When

the supplied grease tube is consumed,

purchase from a HITACHI Authorized

Service Center.

6. Service and repairs

All quality power tools will eventually require servicing or replacement of parts because

of wear from normal use. To assure that only authorized replacement parts will be

used, all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE

CENTER, ONLY.

7. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

Crank cover

Fig. 5

01Eng_H55SC_US 7/6/07, 10:4613

English

14

CAUTION: Repair, modification and inspection of Hitachi Power Tools must be carried

out by a Hitachi Authorized Service Center.

This Parts List will be helpful if presented with the tool to the Hitachi

Authorized Service Center when requesting repair or other maintenance.

In the operation and maintenance of power tools, the safety regulations

and standards prescribed in each country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved and modified to incorporate the

latest technological advancements.

Accordingly, some parts (i.e. code numbers and/or design) may be changed without

prior notice.

01Eng_H55SC_US 7/6/07, 10:4614

English

15

ACCESSORIES

WARNING: ALWAYS use Only authorized HITACHI replacement parts and

accessories. NEVER use replacement parts or accessories which are

not intended for use with this tool. Contact HITACHI if you are not sure

whether it is safe to use a particular replacement part or accessory

with your tool.

The use of any other attachment or accessory can be dangerous and

could cause injury or mechanical damage.

NOTE: Accessories are subject to change without any obligation on the part of the HITACHI.

STANDARD ACCESSORIES

(1) Steel Case (Code No. 302214) ............................................................................................ 1

(2) D-type Side handle (Code No. 986959) .............................................................................. 1

(3) Dust Cover (Code No. 985468) ........................................................................................... 1

(4) Bull Point (Code No. 985430) .............................................................................................. 1

(5) Allen Wrench 6 mm (Code No. 872422) ............................................................................ 1

OPTIONAL ACCESSORIES.....sold separately

For accessories in detail please call HITACHI AT 1-800-59-TOOLS

1. Crushing

(1) Bull point

Overall length Code No.

12" (300 mm) 985430

16" (406 mm) 985431

01Eng_H55SC_US 7/6/07, 10:4615

English

16

2. Groove digging and edging

3. Asphalt cutting

4. Hammer grease A

30g (in a tube) (Code No. 981840)

NOTE:

Accessories are subject to change without any obligation on the part of the HITACHI.

(1) Cold chisel

Overall length Code No.

12" (300 mm) 985432

16" (406 mm) 985433

(1) Cutter

Overall length Width Code No.

17" (430 mm) 2" (50 mm) 985434

01Eng_H55SC_US 7/6/07, 10:4616

Page is loading ...

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construc-

tion activities contains chemicals known to the State of California to cause cancer,

birth defects or other reproductive harm. Some examples of these chemicals are:

● Lead from lead-based paints,

● Crystalline silica from bricks and cement and other masonry products, and

● Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type

of work. To reduce your exposure to these chemicals: work in a well ventilated area,

and work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

AVERTISSEMENT:

La poussière résultant d'un ponçage, d'un sciage, d'un meulage, d'un perçage ou

de toute autre activité de construction renferme des produits chimiques qui sont

connus par l'Etat de Californie pour causer des cancers, des défauts de naissance

et autres anomalies de reproduction. Nous énumérons ci-dessus certains de ces

produits chimiques:

● Plomb des peintres à base de plomb,

● Silice cristalline des briques et du ciment et autres matériaux de maçonnerie, et

● Arsenic et chrome du bois d'oeuvre traité chimiquement.

Le risque d'exposition à ces substances varie en fonction de la fréquence d'exécution

de ce genre de travail. Pour réduire l'exposition à ces produits chimiques, travailler

dans un lieu bien ventilé, et porter un équipement de protection agréé, par exemple

un masque anti-poussière spécialement conçu pour filter les particules microscopiques.

ADVERTENCIA:

Alogunos polvos creados por el lijado mecámico, el aserrado, el esmerilado, el

taladrado y otras actividades de construcción contienen sustancias químicas conocidas

por le Estado de California como agentes cancerígenos, defectos congénitos y otros

daños reproductores. Algunos ejemplos de estas sustancias químicas son:

● El plomo de las pinturas a base de plomo,

● El sílice cristalino de los ladrillos y cemento y otros productos de mampostería, y

● El arsénico y el cromo de la madera tratada químicamente.

El riesgo resultante de la exposición varía según la frecuencia con que se realiza

este tipo de trabajo. Para reducir la exposicíon a esta sustancias químicas: trabaje

en un lugar bien ventilado y realice el trabajo utilizando el equipamiento apropiado,

tal como las máscares para el polvo especialmente diseñados para eliminar las

partículas minúsculas.

Issued by

Hitachi Koki Co., Ltd.

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo 108-6020, Japan

Distributed by

Hitachi Koki U.S.A., Ltd.

3950 Steve Reynolds Blvd.

Norcross, GA 30093

Hitachi Koki Canada Co.

6395 Kestrel Road

Mississauga ON L5T 1Z5

707

Code No. C99038365 N

Printed in Japan

03Spa_H55SC_US 7/6/07, 10:5048

Infocus H 55SC User manual

This manual is also suitable for

Infocus H 55SC User manual

in other languages

Related papers

Other documents