Maytag MCD2257HEW - 22 cu. Ft. Refrigerator User manual

Side-by-Side

Use & Care Guide

R

Table of Contents

Important Safety Instructions..... 1-2

Installation ...................................... 3-7

Temperature Controls................. 8-10

Fresh Food Features ................. 11-14

Freezer Features.............................. 15

Ice and Water............................. 16-18

Water Filter................................. 19-21

Food Storage Tips..................... 22-24

Care and Cleaning.................... 25-28

Operating Sounds ........................... 29

Troubleshooting......................... 30-33

Warranty & Service ......................... 35

Guide d’utilisation et d’entretien. 36

Guía de uso y cuidado ................... 74

1

Important Safety Instructions

WARNING – Hazards or unsafe practices which

COULD result in severe personal injury or death.

WARNING

DANGER – Immediate hazards which WILL result

in severe personal injury or death.

DANGER

CAUTION – Hazards or unsafe practices which COULD

result in minor personal injury or property damage.

CAUTION

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining or operating appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words,

Labels

This appliance is equipped with a three-prong

grounded plug for your protection against possible

electrical shock hazards. It must be plugged into a

properly grounded wall receptacle. Where a standard

two-prong wall receptacle is encountered, it is the

personal responsibility and obligation of the customer

to have it replaced with a properly grounded three-

prong wall receptacle. Do not, under any

circumstances, cut or remove the third (ground)

prong from the power cord. Do not use an adapter

plug.

Power supply cord with

three-prong grounded plug

Properly

grounded type

wall receptacle

To reduce risk of injury or death, follow basic

precautions, including the following:

Important: Child entrapment and suffocation are

not problems of the past. Junked or abandoned

refrigerators are still dangerous – even if they sit out

for “just a few days.” If you are getting rid of your old

refrigerator, please follow the instructions below to

help prevent accidents.

Before you throw away your old

refrigerator or freezer:

• Take off the doors.

• Leave the shelves in place so

children may not easily climb

inside.

• Cut off power cord plug.

DANGER

Installer: Please leave this guide with this appliance.

Consumer: Please read and keep this Use and

Care Guide for future reference; it provides the

proper use and maintenance information.

Keep sales receipt and/or canceled check as proof

of purchase.

Call: 1-800-688-9900 USA

1-800-688-2002 Canada

Have complete model and serial number

identification of your refrigerator. This is located on a

data plate inside the fresh food compartment, on the

upper right side. Record these numbers below for

easy access.

Model Number _______________________________

Serial Number ________________________________

Date of Purchase______________________________

In our continuing effort to improve the quality and

performance of our appliances, it may be necessary

to make changes to the appliance without revising

this guide.

2

SAVE THESE INSTRUCTIONS

Important Safety Instructions

To reduce risk of fire, electric shock, serious

injury or death when using your refrigerator,

follow basic precautions, including the following:

1. Read all instructions before using the refrigerator.

2. Observe all local codes and ordinances.

3. Be sure to follow grounding instructions.

4. Check with a qualified electrician if you are not

sure this appliance is properly grounded.

5. Do not ground to a gas line.

6. Do not ground to a cold-water pipe.

7. Refrigerator is designed to operate on a separate

115 volt, 15 amp., 60 cycle line.

8. Do not modify plug on power cord. If plug does

not fit wall receptacle, have proper receptacle

installed by a qualified electrician.

9. Do not use a two-prong adapter, extension cord

or power strip.

10. Do not remove warning tag from power cord.

11. Do not tamper with refrigerator controls.

12. Do not service or replace any part of refrigerator

unless specifically recommended in Use and Care

Guide or published user-repair instructions.

Do not attempt service if instructions are not

understood or if they are beyond personal skill

level.

13. Always disconnect refrigerator from electrical

supply before attempting any service. Disconnect

power cord by grasping the plug, not the cord.

14. Install refrigerator according to Installation

Instructions. All connections for water, electrical

power and grounding must comply with local

codes and be made by licensed personnel when

required.

15. Keep your refrigerator in good condition. Bumping

or dropping refrigerator can damage refrigerator

or cause refrigerator to malfunction or leak. If

damage occurs, have refrigerator checked by

qualified service technician.

16. Have worn power cords and/or loose plugs

replaced by a qualified service technician.

17. Always read and follow manufacturer’s storage

and ideal environment instructions for items being

stored in refrigerator.

18. Your refrigerator should not be operated in the

presence of explosive fumes.

19. Children should not climb, hang or stand on any

part of the refrigerator.

20. Clean up spills or water leakage associated with

water installation.

WARNING

3

Installation

To avoid severe personal injury or death,

observe the following:

• Disconnect power to refrigerator before removing

doors. Connect power only after replacing doors.

• Green ground wire must be attached to top hinge

while performing door removal and replacement.

• Tape decorative panels (select models) securely

into place before removing door handles.

WARNING

To avoid property damage, observe the following:

• Protect vinyl or other flooring with cardboard, rugs

or other protective material prior to moving

refrigerator.

• Do not adjust refrigerator to be any shorter than

68

1

⁄2” tall (minus hinge and cap). Doing so may

damage underside components.

CAUTION

Location

• Do not install refrigerator near oven, radiator or

other heat source. If not possible, shield refrigerator

with cabinet material.

• Do not install where temperature falls below 55° F

(13° C) or rises above 110° F (43° C). Malfunction

may occur at this temperature.

• Refrigerator is designed for indoor household

application only.

Measuring the Opening

When installing your refrigerator, allow

1

⁄2” space at top

and

1

⁄2” space behind machine compartment cover

(located in the rear) for proper air circulation. If the

refrigerator is placed with the door hinge side against

a wall, you may want to allow additional space so the

door can be opened wider.

Subflooring or floor coverings (i.e. carpet, tile, wood

floors, rugs) may make your opening smaller than

anticipated.

Some clearance may be gained by using the leveling

procedure under Leveling.

Important: If refrigerator is to be installed into a

recess where the top of the refrigerator is completely

covered, use dimensions from floor to top of hinge cap

to verify proper clearance.

Transporting Your Refrigerator

• NEVER transport refrigerator on its side. If an

upright position is not possible, lay refrigerator on its

back. Allow refrigerator to sit upright for

approximately 30 minutes before plugging it in to

assure oil returns to the compressor. Plugging

refrigerator in immediately may cause damage to

internal parts.

• Use an appliance dolly when moving refrigerator.

ALWAYS truck refrigerator from its side or

back–NEVER from its front.

• Protect outside finish of refrigerator during transport

by wrapping cabinet in blankets or inserting padding

between the refrigerator and dolly.

• Secure refrigerator to dolly firmly with straps or

bungee cords. Thread straps through handles when

possible. Do not over-tighten. Over-tightening

restraints may dent or damage outside finish.

Door and Hinge Removal

Some installations require door removal to get

refrigerator to final location.

1. Unplug power cord from power source.

2. Remove toe grille (see page 4).

• Open both doors 180°, or as wide as possible.

• If tube end is damaged, cut off

5

⁄8” before

reconnecting.

• If leaking occurs, reconnect the line.

To Disconnect the Water Line:

• Push in white collar (A) and hold.

• Pull the door-side tube from the connector (B).

To Reconnect the Water Line:

• Firmly push tube

5

⁄8” into the connector. Use

lines on the tube as a guide for full insertion.

Note: For refrigerators in operation, shut off water

before removing water line from the door.

A

B

4

6. For ice and water dispensing models only:

Detach main wire connector harness and red wire

harness.

• To detach main wire

harness, use a flat blade

tool or fingernail to press

junction point between two

connectors to release.

• To detach red wire harness,

press tab on underside of

connector to release.

7. Remove top hinges along with

doors.

Installation

8. Remove bottom hinges

with a

3

⁄8” hex head driver.

Replacing the Doors

• To replace the doors, follow the steps in Door and

Hinge Removal in reverse order.

Important: If water line tube end is damaged, cut off

5

⁄8” before reconnecting.

3. Close doors.

4. Remove top hinge covers by

removing Phillips screws.

5. Unscrew

5

⁄16” hex head screws from

top hinges.

For water dispensing

models only:

• Do not remove screw

connecting green ground

wire.

Leveling

To protect personal property and refrigerator

from damage, observe the following:

• Protect vinyl or other flooring with cardboard, rugs,

or other protective material.

• Do not use power tools when performing leveling

procedure.

CAUTION

To enhance the appearance and maintain performance,

the refrigerator should be level.

3. Select models also have rear adjustment screws

(B). Using the hex head driver, turn each of these

adjustment screws (B) to raise or lower the rear of

the refrigerator.

4. Using the carpenter’s level, make sure front of

refrigerator is

1

⁄4” (6 mm) or

1

⁄2 bubble higher than

back of refrigerator and that the refrigerator is level

from side to side.

5. If required, correct rocking of refrigerator by

turning rear adjustment screw clockwise to raise

rocking corner. If doors are uneven, do the

following:

A

B

A

B

Materials Needed:

•

3

⁄8” hex head driver

• Carpenter’s level

1. Remove toe grille.

• Grasp firmly and pull outward

to unclip.

2. Using hex head driver, turn front adjustment

screws (A) clockwise to raise and counterclockwise

to lower the front of the refrigerator.

Notes:

• Complete any required door reversal, panel

installation and/or a water supply connection

before leveling.

• Some models only have adjustment screws (A).

Cont.

5

Connecting the Water Supply

(select models)

To reduce the risk of injury or death, follow

basic precautions, including the following:

• Read all instructions before installing ice maker.

• Do not attempt installation if instructions are not

understood or if they are beyond personal skill

level.

• Observe all local codes and ordinances.

• Do not service ice maker unless specifically

recommended in Use & Care Guide or published

user-repair instructions.

• Disconnect power to refrigerator before installing

ice maker.

• Water damage due to an improper water

connection may cause mold/mildew growth. Clean

up spills or leakage immediately!

WARNING

To avoid property damage or possible injury,

follow basic precautions, including the

following:

• Consult a plumber to connect

1

⁄4” O.D. copper

tubing to household plumbing to assure

compliance with local codes and ordinances.

• Confirm water pressure to water valve is between

35 and 100 pounds per square inch, 20 pounds

per square inch without filter.

• Do not use a self-piercing, or

3

⁄16” saddle valve.

Both reduce water flow and can become clogged

over time, and may cause leaks if repair is

attempted.

• Tighten nuts by hand to prevent cross threading.

Finish tightening nuts with pliers and wrenches.

Do not over-tighten.

• Wait two to three hours before placing refrigerator

into final position to check and correct any water

leaks. Recheck for leaks after 24 hours.

• Verify the copper tubing under the sleeve is

smooth and free from defects. Do not reuse an

old sleeve.

CAUTION

Installation

• Determine which

door needs to be

raised.

• Turn front roller

adjustment screw

(A) clockwise to

raise front corner of

door.

• If one refrigerator door has reached the limit of

its adjustment range and doors are still not level,

raise or lower the opposite door by turning roller

adjustment screw clockwise or counterclockwise.

• Check with level to verify

1

⁄4” tilt to the back for

proper door closure.

• If refrigerator is aligned and stable, replace toe

grille.

• Align the toe grille mounting clips with the lower

cabinet slots.

• Push the toe grille firmly until it snaps into place.

Materials Needed:

•

1

⁄4” outer diameter flexible copper tubing

• Shut-off valve (requires a

1

⁄4” hole to be drilled into

water supply line before valve attachment)

• Adjustable wrench (2)

•

1

⁄4” hex nut driver

Notes:

• Use copper tubing only for installation. Plastic is

less durable and can cause damage.

• Add 8’ to tubing length needed to reach water

supply for creation of service loop.

1. Create service loop with

copper tubing (minimum 2’

diameter). Avoid kinks in the

copper tubing when

bending the service loop. Do

not use plastic tubing.

2. Remove plastic cap from water valve

inlet port.

2’ diameter

minimum

6

Installation

Handle Installation

If not installed, the handle is located in the interior of

the fresh food section or attached to the back of your

refrigerator. Remove and discard handle packaging

and tape.

Handle design varies from refrigerator to refrigerator.

Please reference the appropriate instructions for your

model.

Plastic Handle with Extensions

Attach Extensions to Handle:

1. Align handle and extension as shown.

2. Place extension in handle opening.

3. Apply slight pressure

to both sides of the

extension piece.

4. Slide extension until it

stops on inside edge

of handle.

To Install:

1. The handles are to be oriented as shown.

2. Align door handle with the door studs.

3. Ensure the large hole in the mounting clip is

positioned down on both ends of the handle.

Door

Stud

5. Grasp the handle firmly and slide

down.

4. Rotate the handle so that the

handle is flat against the door.

3. Place brass nut (A) and sleeve (B)

on copper tube end as illustrated.

Reminder: Do not use an old

sleeve. The nut and sleeve are

provided in the Use and Care

packet.

5. Slide brass nut over sleeve and

screw nut into inlet port.

Place adjustable wrench on nut

(1) attached to plastic waterline

and maintain position.

Using second adjustable wrench

turn the lower nut (2)

counterclockwise and fully

tighten while holding the upper

nut in place.

Important: Do not over-tighten. Cross threading

may occur.

4. Place end of copper tubing into

water valve inlet port. Shape

tubing slightly. Do not kink – so

that tubing feeds straight into inlet

port.

A

B

6. Pull on tubing to confirm

connection is secure.

Connect tubing to frame

with water tubing clamp (C)

and turn on water supply.

Check for leaks and correct

if necessary. Continue to

observe the water supply

connection for two to three

hours prior to moving the

refrigerator to its permanent

location.

7. Monitor water connection for 24 hours. Correct

leaks, if necessary.

A

B

Cont.

C

1

2

7

4. Grasp the handle firmly and pull

downward to remove.

5. Repeat for freezer handle.

Full-Length Aluminum

Handles

Materials Needed:

• Phillips screwdriver

To avoid possible injury and damage to property,

tape decorative panels (select models) securely into

place before removing door handles.

WARNING

To Remove:

1. Release top door trim by removing

Phillips screws from top of fresh food

door, retaining screws for later use.

2. Grasp handle firmly with both hands.

Slide handle upward

approximately

3

⁄4” to release.

3. Repeat instructions 1-2 to

remove other handle.

To Reinstall:

1. Repeat in reverse order.

Wide-by-Side™ Handles

Materials Needed:

• Gloves to protect hands

• Plastic door handle removal card (or

1

⁄32”

thick plastic card), retain the card

• Flat blade screwdriver

To Install:

1. Align fresh food handle with trim

retainer and door clip.

2. Make sure the tabs of the handle clip

are below the tabs of the door clip.

3. Rotate the handle so that the handle

is flat against the door (see page 6).

4. The tab on the lower part of the

handle will align with the hole in the

handle cap.

5. Slide handle upward until it clicks.

6. Snap top of handle into trim retainer clip.

7. Repeat for freezer handle.

To Remove:

1. Protect the area above the handle trim with tape.

Insert the tip of a flat blade screwdriver between

the handle trim and door panel. Carefully pry the

trim away from the door panel.

2. Pull trim free from the trim retainer.

3. Insert door removal card (or

1

⁄32” thick plastic card)

between the handle and door panel (approximately

1

⁄2”).

Installation

To Remove:

1. Grasp the lower part of the handle firmly,

slide up, lift and remove from the

surface.

To Remove:

• Loosen set screws in handle using

3

⁄32” Allen

wrench.

• Repeat the procedure on all screws.

To Replace:

• Align handle with the mounting posts.

• Apply upward pressure to the handle and hold.

• Fully tighten all set screws to secure handle in

place.

Metal Handle

Materials Needed:

•

3

⁄32” Allen wrench

• Gloves to protect hands

Note: Metal handles can scratch doors.

To Install:

1. Release top door trim by

removing Phillips screws from

top of fresh food door, retaining

screws for later use.

2. Align notches on back of handle

with retaining clips on doors. Insert

clips into notches and slide handle

down until it contacts bottom trim.

3. Replace top door trim and Phillips screws.

4. Repeat instructions 1-3 to install other handle.

Door Clip

Adjusting the Controls

• 24 hours after adding food, you may decide that one

or both compartments should be colder or warmer. If

so, adjust the control(s) as indicated in the

Temperature Control Guide, page 9.

8

Temperature Controls

Dial Temperature Controls

(select models)

The controls are located at the back left of the

refrigerator compartment.

Note: The Freezer control turns the cooling system

on. Neither section will cool if freezer control is set

to OFF.

Initial Control Settings

After plugging the refrigerator in,

set the controls.

• To adjust the controls, turn the

control knob to the left or right

as desired.

• Set the Freezer control on 4.

• Set the Refrigerator control on 4.

• Let the refrigerator run at least 8

to 12 hours before adding food.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabinet. This condition will be more noticeable when

you first start the refrigerator, during hot weather and

after excessive or lengthy door openings.

Adjusting the Controls

• 24 hours after adding food, you may decide that one

or both compartments should be colder or warmer. If

so, adjust the control(s) as indicated in the

Temperature Control Guide table. See page 22 for

instructions on checking compartment temperature.

• Except when starting the refrigerator, do not change

either control more than one number at a time.

• Allow 24 hours for temperatures to stabilize.

• Changing either control will have some effect on the

temperature of the other compartment.

Temperature Control Guide

Refrigerator too warm

Refrigerator too cold

Freezer too warm

Freezer too cold

Turn refrigerator OFF

Turn the Refrigerator control

to next higher number.

Turn the Refrigerator control

to next lower number.

Turn the Freezer control to

next higher number.

Turn the Freezer control to

next lower number.

Turn the Freezer control to

OFF.

Note: Turning Freezer control to OFF stops cooling

in both compartments. It does not shut off power to

the refrigerator.

Touch Temperature Controls

(select models, style varies by model)

The controls are located at the top front of the

refrigerator compartment.

Control

Initial Control Settings

After plugging the refrigerator in, set the controls.

• Pressing the or pads adjusts the controls to

the desired setting.

• Set the Freezer control on 4.

• Set the Refrigerator control on 4.

• Let the refrigerator run at least 8 to 12 hours before

adding food.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabinet. This condition will be more noticeable when

you first start the refrigerator, during hot weather and

after excessive or lengthy door openings.

Cont.

9

Temperature Controls

Triple Cool Climate Control

(select models)

The control is located at the top front of the fresh food

compartment.

Control

Initial Temperature Setting

Temperatures are preset at the factory at 38° F (3° C)

in the fresh food compartment and 0° F (-17° C) in the

freezer compartment.

Adjusting the Control

24 hours after adding food, you may decide that one or

both compartments should be colder or warmer. If so,

adjust the control as indicated in the Temperature

Control Guide.

• The first touch of the or pads shows the

current temperature setting.

Temperature Control Guide

Refrigerator too warm

Refrigerator too cold

Freezer too warm

Freezer too cold

Turn refrigerator OFF

Set the Refrigerator control to

next higher number by

pressing the pad.

Set the Refrigerator control to

next lower number by

pressing the pad.

Set the Freezer control to next

higher number by pressing the

pad.

Set the Freezer control to next

lower number by pressing the

pad.

Press the Freezer or

Refrigerator pad until a

dash “–” appears in the

display.

• The display will show the new setting for

approximately three seconds, and then return to the

actual temperature currently within that compartment.

• Do not change either control more than one degree at

a time. Allow temperature to stabilize for 24 hours

before making a new temperature adjustment.

Temperature Control Guide

Refrigerator too cold

Refrigerator too warm

Freezer too cold

Freezer too warm

Turn refrigerator OFF

Set the Refrigerator control to

next higher number by

pressing the pad.

Set the Refrigerator control to

next lower number by

pressing the pad.

Set the Freezer control to next

higher number by pressing the

pad.

Set the Freezer control to next

lower number by pressing the

pad.

Press the Freezer pad

until “OFF” appears in the

display. Press either the

Freezer or Refrigerator

pad to turn back on.

Speed Ice

When activated, Speed Ice reduces the freezer

temperature to the optimum setting for 24 hours in order

to produce more ice. Important: When the Speed Ice

feature is in operation, the and pads for the

Freezer control will not operate.

Reset Filter (select models)

When a water filter has been installed in the refrigerator,

the yellow Order light will illuminate when 90 % of the

volume of water for which the filter is rated has passed

through the filter OR 11 months have elapsed since the

filter has been installed.

The red Replace light will illuminate when the rated

volume of water has passed through the filter OR 12

months have elapsed since the filter was installed. A new

filter should be installed immediately when the Replace

light is illuminated.

After replacing the filter, press and hold the Reset Filter

pad for three seconds. The Order and Replace lights will

go off.

Vacation Mode

The Vacation Mode feature causes the freezer to defrost

less frequently, conserving energy. The Vacation Mode

indicator light will illuminate when the feature is activated.

To deactivate, press the Vacation Mode pad again OR

open either door. The indicator light will go off.

• Except when starting the refrigerator, do not change

either control more than one number at a time.

• Allow 24 hours for temperatures to stabilize.

10

Temperature Controls

Temp Alarm

The Temp Alarm system will alert you if the freezer or

fresh food temperatures exceed normal operating

temperatures due to a power outage or other event.

When activated, the Temp Alarm light will illuminate.

If the freezer or fresh food temperatures have exceeded

these limits, the display will alternately show the current

compartment temperatures and the highest

compartment temperatures reached when the power

was out. An audible alarm will sound repeatedly.

Press the Temp Alarm pad once to stop the audible

alarm. The Temp Alarm light will continue to flash and

the temperatures will alternate until the temperatures

have stabilized.

To turn off Temp Alarm, press and hold the Temp Alarm

pad for three seconds. The indicator light will go off.

Door Alarm

The Door Alarm will alert you when one of the doors has

been left open for five continuous minutes. When this

happens, an audible alarm will sound every few seconds

until the door is closed OR the Door Alarm pad is

pressed to deactivate the feature.

Max Cool

When activated, Max Cool causes the fresh food and

freezer temperatures to drop to the minimum settings on

the control. This cools down the refrigerator and freezer

after extended door openings or when loading the

refrigerator or freezer with warm food. Important:

When the Max Cool feature is in operation, the

and pads for the refrigerator and freezer

controls will not operate.

To activate, press the Max Cool pad. Max Cool will

deactivate automatically after 12 hours, OR press the

Max Cool pad to deactivate the feature.

User Preferences

Access the User Preferences menu to:

• Activate or turn off Super Cool (select models).

• Change the temperature display from °F to °C .

• Enable or disable audible alarms.

• Adjust the light level at which the Dispenser Auto

Light will illuminate (when this feature is activated

on the ice and water dispenser) (select models).

• Activate the Sabbath Mode.

To access the User Preferences menu, press and hold

the Door Alarm pad for three seconds. When in the

User Preferences mode, a short title for the feature will

appear in the Freezer temperature display and the

feature status will appear in the Refrigerator display.

1. Use the Freezer up and down controls to scroll

through the features.

2. When the desired feature is displayed, use the

Refrigerator up and down controls to change the

status.

3. When changes are complete, press the Door Alarm

pad for three seconds OR close the Fresh Food door.

Super Cool (CC) (select models)

When Super Cool is ON, an air-mixing fan in the fresh

food compartment is activated to improve air flow and

temperature control. To save energy, this feature may

be deactivated by pressing OFF.

Temperature Display (F_C)

Change the display to show temperatures in degrees

Fahrenheit or degrees Celsius.

Alarm (AL)

When the Alarm mode is OFF, all audible alarms will be

disabled until the feature is turned ON.

Auto Light Level Selection (LL) (select models)

This setting adjusts the light level at which the

dispenser light will illuminate when the sensor detects

that the light levels in the room are low. Setting 1 is

the darkest light level setting, setting 9 is the lightest

light level setting. Important: The Auto Light (select

models) must be activated on the ice and water

dispenser control to take advantage of this option.

Sabbath Mode (SAB)

When the Sabbath Mode is ON, all control lights and

the night light will be disabled until the feature is

turned OFF. This feature does not disable the interior

lights. Press any pad to restore the control lights.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabinet. This condition will be more noticeable when

the refrigerator is first started, during hot weather and

after excessive or lengthy door openings.

Notes:

• Door openings will not deactivate Vacation Mode for

approximately one hour after activation.

• If vacationing for more than a few days, see the

Preparing for Vacation section, page 28.

11

Fresh Food Features

Shelves

Your refrigerator has either Spill-Catcher™ or non-

sealed shelves. Spill-Catcher™ shelves have a spill

retainer edge which allows for easier clean up and

some are equipped with the Easy-Glide slide out

feature. To slide out (select models), grasp the front of

the shelf and pull forward. Push in the shelf to return

to the original position.

To Remove a Shelf:

• Slightly tilt up the

front and lift up the

rear of the shelf, then

pull the shelf straight

out.

To Lock the Shelf Into Another Position:

• Tilt up the front edge of the shelf.

• Insert the hooks into the desired frame openings and

let the shelf settle into place.

• Be sure the shelf is securely locked at the rear.

The Crisper Top serves as the lower fresh food shelf.

To Remove the Crisper Top:

• Remove drawers as indicated (see page 13).

• Place hand under the frame to push up the glass. Lift

glass out.

To Install:

• Repeat above instructions in reverse order.

Elevator™ Shelf (select models)

The Elevator™ Shelf is equipped with a spill-retaining

edge and the Easy-Glide™ slide-out feature. It can be

adjusted up or down without unloading.

To avoid personal injury or property damage,

observe the following:

• Never attempt to adjust a shelf that is loaded with

food, except in the case of the Elevator

TM

Shelf.

• Confirm shelf is secure before placing items on

shelf.

• Handle tempered glass shelves carefully. Shelves

may break suddenly if nicked, scratched, or

exposed to sudden temperature change.

CAUTION

To Slide Out Elevator™ Shelf:

• Grasp the front of the shelf and pull forward.

• Push the shelf in to return to original position.

To Adjust the Elevator™ Shelf:

• Pull out the knob on the crank handle.

• Rotate the crank clockwise to raise the shelf, and

counterclockwise to lower the height of the shelf.

To Remove Elevator™ Shelf:

• Completely unload the shelf and pull the shelf

forward.

• Pull until the shelf stops.

• Press up on the tabs located underneath its outside

edges and continue pulling forward until the shelf is

clear of the frame.

To Replace Elevator™ Shelf:

• Align the shelf to the frame and push it all the way

back. It is not necessary to press up on the tabs for

reinstallation.

In ordinary use, the Elevator™ Shelf frame assembly

does NOT require removal. Though unlikely, and not

recommended, the correct removal procedure is as

follows:

To Remove Frame Assembly:

• Unload the shelf completely.

• Slide the shelf forward about 2” and manually move

the two rear latches toward the shelf center.

• While supporting the entire shelf and frame from

underneath, lift slightly and rotate the assembly

approximately 30° to allow the rear mechanism to

clear the vertical rear side rails.

• The entire assembly can then be moved forward

and clear of the refrigerator compartment.

To Reinstall Frame Assembly:

• Reverse the removal procedure. Be sure the shelf

is in a level position. When the sliding shelf is

pushed to the rear, it will reposition the rear latches

to their correct operating position.

(style may vary)

12

To Remove:

• Slide dairy center up and pull out.

To Install:

• Slide assembly in and down so that the hooks are

firmly seated on the door liner.

To Remove Dairy Door:

• Press in sides of dairy door and pull out.

To Install Dairy Door:

• Slide sides of dairy door inside dairy center until

hinge points snap into place.

Storage Drawers

Humidity-Controlled Crisper Drawers

The Crisper Drawers provide a higher humidity

environment for fresh fruit and vegetable storage.

Controls

The crisper controls regulate the amount of humidity in

the crisper drawer. Slide control toward the FRUIT

setting for produce with outer skins. Slide control

toward the VEGETABLES setting for leafy produce.

Dairy Center

The Dairy Center provides convenient

door storage for spreadable items such

as butter and margarine. On select

models, this compartment can be

moved to several different locations to

accommodate storage needs.

Fresh Food Features

Refrigerator Pak Can

Organizer (select models)

The Refrigerator Pak Can

Organizer conveniently dispenses

up to a 12-pack of individual

beverage cans. To load beverages

into the organizer:

• Open a 12-pack sleeve of

beverages.

• Slide can organizer over the

cutout portion of beverage

sleeve.

• Place container and sleeve in an

upright position in a door bucket

located in the fresh food door

compartment.

The dispenser sits in the door

bucket and can be moved to

accommodate a variety of storage

needs.

Adjustable Deep Tilt-Out Door Buckets

(select models)

The Adjustable Deep Tilt-Out Door Bucket provides

easy access to food items stored in the door.

To Remove Bucket:

• Tilt bucket out.

• Pull straight out of the bracket.

To Install Bucket:

• Tilt the front of the bucket down slightly.

• Slide into bracket and tip upright.

To Move Bucket Frame to

Another Location:

• Remove bucket.

• Lift bracket up and pull straight

out.

• Place the bracket in a new location.

Door Buckets

Door Buckets can be moved to meet individual

storage needs.

To Remove:

• Lift bucket up and pull straight

out.

To Install:

• Place bucket in desired door liner retainer, push

down until bucket stops.

Cont.

13

Fresh Food Features

Automatic Humidity Control

Some crispers are equipped with an Automatic

Humidity Control system, eliminating the need for

manual humidity slide controls on the drawer. A

fabric-like material* covers small air vents in the shelf

insert above the crispers.

This material controls the flow of moisture out of the

crisper. If a food spill should occur on the air vent or

fabric-like material, wipe with a clean, damp cloth.

Note: For best results, keep the crispers tightly

closed.

To Remove:

• Pull drawer out to full

extension. (On select

models, press tabs toward

oneself to release drawer

from rails.) Tilt up front of

drawer and pull straight out.

To Install:

• Insert drawer into frame rails and push back into

place.

Temperature-Controlled

Drawer (select models)

This drawer can be used for storage of

miscellaneous items.

The drawer features a control that

regulates the air temperature in the drawer. Set the

control to Cheese to provide normal refrigerator

temperature. Use the Meats setting for meats.

Can Rack™ (select models)

The Can Rack™ slides out from

underneath the Spillsaver™

stationary shelf. The Can Rack™

holds up to twelve 12-ounce

beverage cans.

To Remove:

• Empty contents of Can Rack™. Pull forward to full

extension and lift front to release from shelf rail

assembly. Pull straight out to remove.

To Install:

• Insert drawer into frame rails and push back into

place.

Note: For best results, keep the crispers tightly

closed.

* The Maytag Automatic Humidity

Control system features a unique,

patented material called Shape

Memory Polymer (SMP) that when laminated to

fabric, becomes DIAPLEX. DIAPLEX is

manufactured by Mitsubishi.

To Remove:

• Pull drawer out to full extension. Tilt up front of

drawer and pull straight out.

To Install:

• Insert drawer into frame rails and push back into

place.

Accessories

Grip Pads (select models)

The Grip Pads prevent objects from

sliding in the door buckets. Grip

Pads are removable and are top-rack

dishwasher safe for easy cleaning.

Covered Storage Bucket

(select models)

The Storage Bucket has a lid and

removable egg tray. When tray is

removed, bucket will accept items

such as a standard egg carton, ice,

etc.

14

Fresh Food Features

Tall Bottle Retainer/Snugger

(select models)

The Tall Bottle Retainer

prevents tall bottles from

tipping forward. The Retainer

can be placed above any

removable door bucket.

The Snugger attached to the Tall Bottle Retainer keeps

bottles and other containers in place when the door is

opened or closed. Adjust the Snugger by sliding from

side to side.

Egg Tray With Handle

(style may vary/select models)

The Egg Tray with Handle holds a

“dozen-plus” eggs. It can be

removed to carry to a work area or to be washed.

Wine Rack (select models)

The Wine Rack provides a place

for horizontally storing wine. The

rack can also hold an egg carton.

Position the rack to rest on the

left hand side of a refrigerator

shelf (this rack cannot be

positioned on an Elevator Shelf™).

15

To Install:

• Slide bin into railing below ice maker until bin locks

into place. Drop ice maker arm to activate ice maker.

Important: Ice bin must be locked in place for proper

ice dispensing. Turn auger driver behind bin

counterclockwise (as shown) to properly align ice bin

with auger driver.

Shelves and Baskets

Fixed Freezer Shelf

To Remove Clip-Mounted Shelves:

• Lift shelf from wall mounting

clips and pull left side of shelf

out of wall mounting holes.

To Install Clip-Mounted Shelves:

• Place left side of shelf in mounting holes and press

down into wall mounting clips.

Shelves

Shelves can be removed to meet individual storage

needs.

To Remove Shelf:

• Snap right side of shelf up from

cabinet railing and slide to right.

To Install Shelf:

• Place shelf in left side cabinet railing snapping shelf

into right side cabinet railing.

Baskets and Drawers

Baskets and drawers (style may vary)

slide out for easy access to items in

back.

To Remove:

• Pull out to its full extension. Lift up front of basket

and remove.

To Install:

• Slide basket or drawer into cabinet railing. Lift up

front of basket or drawer, and slide to the back of

refrigerator.

Ice Storage Bin

The Ice Storage Bin is located below the automatic ice

maker.

To Remove:

• Raise ice maker arm to deactivate ice maker. Lift

front of bin and pull out to its full extension. Lift up

front of bin and remove.

Freezer Features

Door Storage

Adjustable Door Buckets

Door Buckets can be moved to meet individual storage

needs.

To Remove:

• Lift the door bucket up until it clears the

retainers on the door liner, then

pull the door bucket straight out.

To Install:

• Slide bucket in above desired door liner retainer and

push down until bucket stops.

Fixed Door Bucket (select models)

The Fixed Door Bucket is located in the

upper section of the freezer door.

Important: Fixed door bucket is NOT

adjustable. If bucket is removed, freezer

light will not deactivate when door is

closed.

Drop-Down Freezer Door Baskets

(select models)

These baskets provide

convenient storage space for

frozen food items that tend

to shift, such as bagged

vegetables.

16

Ice and Water

Automatic Ice Maker

(non-dispenser models)

Note: Energy rating guides that are posted on the

refrigerator at the time of purchase do not include

optional ice maker energy usage.

To avoid personal injury or property damage,

observe the following:

• Do not place fingers or hands on the automatic

ice making mechanism while the refrigerator is

plugged in. This will help protect you from possible

injury. It will also prevent interference with moving

parts of the ejector mechanism and the heating

element that releases the cubes.

• Under certain rare circumstances, ice cubes may

be discolored, usually appearing with a green-

bluish hue. The cause of this unusual discoloration

can be a combination of factors such as certain

characteristics of local waters, household

plumbing and the accumulation of copper salts in

an inactive water supply line which feeds the ice

maker. Continued consumption of such discolored

ice cubes may be injurious to health. If such

discoloration is observed, discard the ice cubes

and contact your dealer to purchase and install a

water line filter.

• Water damage due to improper water connection

may cause mold/mildew growth.

• Clean up water and ice spills to avoid personal

injury and to prevent mold/mildew growth.

WARNING

Some models are automatic ice maker ready. The

number of the appropriate ice maker kit is IC10S. The

kit contains installation instructions and water

connection instructions.

Other models have a factory installed ice maker.

Connect the ice maker to the water supply as

instructed on pages 5-6. Proper water flow and a

level refrigerator are essential for optimal ice

maker performance.

Operating Instructions

• Confirm ice bin is in place and ice maker arm is

down.

• After freezer section reaches

between 0° to 2° F (-18° to -17° C),

ice maker fills with water and

begins operating. You will have a

complete harvest of ice

approximately every three hours.

• Allow approximately 3-6 hours after installation to

receive first harvest of ice.

• Discard ice created within first 12 hours of operation

to verify system is flushed of impurities.

• Stop ice production by raising ice maker arm until

click is heard.

• Ice maker will remain in the OFF position until arm is

pushed down.

• The first one or two batches will probably contain

undersized and irregular cubes because of air in the

supply line.

• When the ice cubes are ejected it is normal for

several cubes to be joined together at the ends. They

can easily be broken apart. The ice maker will

continue to make ice until the supply of ice cubes

raises the sensor arm, shutting the ice maker off.

• Certain sounds may accompany the various cycles of

the ice maker. The motor may have a slight hum, the

cubes will rattle as they fall into an empty storage

pan and the water valve may click or “buzz”

occasionally.

• If the ice is not used frequently, the ice cubes will

become cloudy, shrink, stick together and taste stale.

Empty the ice storage bin periodically and wash it in

lukewarm water. Be sure to dry the bin thoroughly

before replacing it.

• Beverages and foods should not be placed in the

ice storage bin for quick chilling. These items can

block the sensor arm, causing the ice maker to

malfunction.

• Turn OFF (arm up) the ice maker when the water

supply is to be shut off for several hours.

To Remove the Ice Bin:

• Pull it forward, away from the ice maker. To avoid the

ice maker dumping ice while the bin is removed, turn

the ice maker OFF by raising the sensor arm.

To Install the Ice Bin:

• Reverse the above procedure. Turn the ice maker ON

by lowering the sensor arm.

17

Dispenser Light (select models)

A light activates within the dispenser area at full power

when dispensing ice or water with the main dispenser

pad.

Dispenser Pad

The Dispenser Pad is located on the back wall of the

dispensing area. When the dispenser pad is pressed,

the selection chosen on the dispenser control panel

will dispense.

Removable Tray

The Removable Tray at the bottom of the dispenser

area is designed to collect small spills and may be

easily removed for cleaning and emptying purposes.

Important: Removable tray does not drain. Do not

allow tray to overflow. If it does, remove tray and wipe

up overflow.

Main

Dispenser

Pad

Removable

Tray

Water Dispenser Operation

To avoid personal injury or property damage,

observe the following:

• Do not put fingers, hands or any foreign object

into dispenser opening.

• Do not use sharp objects to break ice.

• Do not dispense ice directly into thin glass, fine

china or delicate crystal.

CAUTION

To Use Dispenser Pad:

• Choose water selection from dispenser control panel.

• Press a sturdy, wide-mouthed container against

dispenser pad. When dispensing crushed ice, hold

container as close to chute as possible to reduce

spraying.

• Release pressure on dispenser pad to stop water

dispensing. A small amount of water may continue to

dispense and collect in dispenser tray. Large spills

should be wiped dry.

Note: During initial use of water dispenser, there

will be a one- to two-minute delay while water tank

fills before water dispenses. Discard first 10-14

glasses of water after initially connecting refrigerator

to household water supply and after extended

periods of nonuse.

Ice and Water

Dispenser Features

(select models)

Dispenser Control (select models)

(control features vary by model)

Ice Dispenser Operation

To Dispense Ice and

Water:

• Select Water, Crush or Cube ice mode by pushing

button on dispenser control panel. A green light

above button indicates mode selection.

• Press container against dispenser pad.

When dispensing crushed ice, hold

container as close to chute as possible to

reduce spraying.

Notes:

• Mode may not be changed while ice dispenser is

in operation.

• If dispenser (select models) is active for more than

five minutes, an automatic lock out sensor will

shut down power to dispenser area. See Dispenser

Lock for unlocking information.

18

Dispenser Lock (select models)

The Dispenser Lock prevents ice or water from

being dispensed.

To Lock Dispenser:

• Press and hold the Lock button for three seconds. A

green indicator light above button will illuminate

when the dispenser is locked.

To Unlock Dispenser:

• Hold the Lock button for three seconds. The green

indicator light above button will go out.

Water Filter Status Indicator

Light (select models)

The Water Filter Status Indicator Light serves as a

reminder to replace the water filter. A green light

indicates that the filter is in good condition. A red light

indicates the filter should be changed. Once light turns

red, it will remain red until function is reset.

To Reset Indicator:

• Press and hold both the Lock and Water

buttons simultaneously for four seconds. The

green filter status indicator light will flash

three times when the function has

successfully reset.

Ice and Water

Auto Light (select models)

The Auto Light function activates the dispenser

light at half-power when the Light Sensor

detects that the light levels in room are low.

To Activate Auto Light:

• Press Auto Light button. A green indicator light

above button illuminates when the sensor is active.

To Deactivate Auto Light:

• Press Auto Light button. The green indicator light

will go out.

Note: The dispenser light will operate when Auto

Light is ON or OFF.

Sabbath Mode (select models)

When activated, the Sabbath Mode deactivates the

control lights while leaving the control operational.

To Activate Sabbath Mode:

• Press and hold the Lock and Auto Light

buttons simultaneously for three to four

seconds. After three to four seconds, the

dispenser lights will turn off.

To Deactivate Sabbath Mode:

• Press and hold both the Lock and Auto Light

buttons simultaneously for three to four seconds.

After three to four seconds, the dispenser lights will

activate.

Notes:

• Dispenser light will not activate during dispensing

while in this mode.

• If the power fails, the control will remain in

Sabbath Mode when power returns.

FrontFill™ Button (select models)

The FrontFill™ button works independently of the

dispenser controls, providing an up-front alternative to

the dispenser pad for dispensing water. This feature is

convenient for filling large items that will not fit into

the dispenser area (i.e. sport bottles, pitchers, large

pans, coffee pots).

This feature allows added convenience of dispensing

ice and water simultaneously. To use, choose your

preferred ice mode from dispenser control panel. Press

container against dispenser pad while pressing the

FrontFill™ button.

Light (select models)

Press the Light pad once to select the Auto

Light function which activates the dispenser

light at half-power when the light sensor detects that

the light levels in room are low. The Auto indicator

light will illuminate.

To Activate Light:

• Press the Light pad again to turn the dispenser light

on continuously. The On indicator light will

illuminate.

To Deactivate Light:

• Press the Light pad a third time to turn the dispenser

light off.

19

Water Filter

Water Filter Removal and

Installation (select models)

To avoid serious illness or death, do not use

refrigerator where water is unsafe or of unknown

quality without adequate disinfection before or after

use of filter.

WARNING

After installing a new water filter, always

dispense water for two minutes before

removing the filter for any reason. Air trapped in

system may cause water and cartridge to eject.

Use caution when removing.

• The bypass cap does not filter water. Be sure to

have replacement cartridge available when filter

change is required.

• If water filtration system has been allowed to

freeze, replace filter cartridge.

• If system has not been used for several months, or

water has an unpleasant taste or odor, flush

system by dispensing water for two to three

minutes. If unpleasant taste or odor persists,

change filter cartridge.

CAUTION

Initial Installation

The water filter is located in the upper right-hand

corner of the fresh food compartment.

1. Remove blue bypass cap and

retain for later use.

2. Remove sealing label from

end of filter and insert into

filter head.

3. Rotate gently clockwise until

filter stops. Snap filter cover

closed.

4. Reduce water spurts by

flushing air from system.

Run water continuously for

two minutes through

dispenser until water runs

steady. During initial use,

allow about a one- to two-minute delay in water

dispersal to allow internal water tank to fill.

• Additional flushing may be required in some

households where water is of poor quality.

Replacing Water Filter

Important: Air trapped in system may cause water

and cartridge to eject. Use caution when

removing.

1. Turn filter counterclockwise until it releases from

filter head.

2. Drain water from filter into sink, and dispose in

normal household trash.

3. Wipe up excess water in filter cover and continue

with Initial Installation, steps 2 and 4.

The filter should be changed at least every 12 months.

Important: Condition of water and amount used

determines life span of water filter cartridge. If water

use is high, or if water is of poor quality, replacement

may need to take place more often.

To purchase a replacement water filter cartridge,

contact your dealer or call 1-877-232-6771 USA or

1-800-688-8408 Canada.

The dispenser feature may be used without a water

filter cartridge. If you choose this option, replace filter

with blue bypass cap.

Page is loading ...

Maytag MCD2257HEW - 22 cu. Ft. Refrigerator User manual

Maytag MCD2257HEW - 22 cu. Ft. Refrigerator User manual

in other languages

Related papers

Other documents