Kohler K-13925-CP Installation guide

Brand: Kohler

Model: K-13925-CP

Category: Sanitary ware

Type: Installation guide

This manual is also suitable for

13925-CP

Kohler K-13925-CP Bedpan Washer is a versatile device designed to make cleaning medical equipment more efficient and hygienic. Its key features include:

Adjustable water flow: The water flow can be limited by adjusting the angle valve.
Adjustable water temperature: The water temperature can be reset by adjusting the angle valve.
Flexible hose: The flexible hose allows for easy maneuverability during cleaning.
Sprayer with multiple spray patterns: The sprayer can be adjusted to provide a variety of spray patterns, from a gentle mist to a powerful stream.
Easy installation: The Bedpan Washer comes with all the necessary mounting hardware and can be installed in minutes.

Kohler K-13925-CP Bedpan Washer is a versatile device designed to make cleaning medical equipment more efficient and hygienic. Its key features include:

Adjustable water flow: The water flow can be limited by adjusting the angle valve.
Adjustable water temperature: The water temperature can be reset by adjusting the angle valve.
Flexible hose: The flexible hose allows for easy maneuverability during cleaning.
Sprayer with multiple spray patterns: The sprayer can be adjusted to provide a variety of spray patterns, from a gentle mist to a powerful stream.
Easy installation: The Bedpan Washer comes with all the necessary mounting hardware and can be installed in minutes.

Page is loading ...

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems please don’t

hesitate to contact us. Our phone numbers and web site are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Adjustable

Wrench

Strap

Wrench

Thread

Sealant

Plumbers

Putty

Phillips

Screwdriver

Blade

Screwdriver

Hex

Wrench

• 9/16" or larger drill

bit for wall material

• Piping support

brackets

• Rags

Plus:

1034408-2-A 2 Kohler Co.

Before You Begin

CAUTION: Risk of property damage. To support the bedpan

washer and piping, provide sufficient reinforcement or mounting

brackets as required inside the wall.

NOTE: Refer to the roughing-in diagram for dimensional

information.

Shut off the main valve and water supply.

Observe all local plumbing codes and building codes.

Plumb using 1/2″ NPT pipe or 1/2″ copper tubing, elbows, and

adapters. Secure the piping to reinforcements in the wall.

Provide the 1/2″ pipe hole in the ﬁnished wall according to the

roughing-in diagram.

Provide screw holes, bracket, or other features as required for

supporting the ﬂange onto the ﬁnished wall.

Kohler Co. reserves the right to make revisions in the design of

bedpan washers without notice, as speciﬁed in the Price Book.

1/2" N.P.T.

Inlet

(7.62 cm)

3-1/2"

(8.9 cm)

Spray

Hose 48" (122 cm) Long

Spray 10-1/2" (26.7 cm)

Long

4-5/8"

(11.7 cm)

2-1/4"

(5.7 cm) D.

4-3/4"

(12.1 cm)

Kohler Co. 3 1034408-2-A

1. Install the Valve Body

NOTE: Apply a thread sealant where applicable.

Thread one supply nipple into the supply outlet in the wall.

Apply a bead of plumbers putty or other sealant to backside of

the ﬂange according to the putty manufacturer’s instructions.

Slide the ﬂange onto and over the supply nipple until it is snug

against the ﬁnished wall. Secure with the ﬂange setscrew.

Remove any excess putty or sealant.

Rotate the valve body clamp to point straight out from the left

side of the valve body. Secure with a screw.

Slide the bell shaped ﬂange onto the valve body holder. Do not

secure with the ﬂange setscrew at this time.

Thread the valve body assembly onto the supply nipple. Ensure

that the valve body assembly is vertically aligned.

Slide the bell shaped ﬂange down the holder until it is snug

against the ﬁnished wall. Secure with one ﬂange setscrew and

two wall screws.

Screw

Screws

Flange

Supply

Outlet

Clamp

Holder

Supply

Nipple

Body

Flange

Apply Plumbers Putty.

1034408-2-A 4 Kohler Co.

2. Install the Hose Assembly

Thread one end of the ﬂexible hose into the body assembly outlet.

Securely tighten.

Thread the other end of the ﬂexible hose into the sprayer outlet.

Securely tighten.

Hang the spray nozzle from the rotated valve assembly clamp.

Key

Body

Assembly

Sprayer

Hose

Kohler Co. 5 1034408-2-A

3. Installation Checkout

NOTE: The water ﬂow from the sprayer can be limited by adjusting

the angle valve.

NOTE: The water temperature can be reset by adjusting the angle

valve.

One Handle Bedpan Washer

For a one handle bedpan washer, turn on the main water supply.

Open both the check valve and the supply valve.

Check for leaks. Repair as needed.

Remove the screw, face, and washer from the sprayer.

Run water through the hose for approximately one minute to

remove debris.

Test and verify that the sprayer operates normally.

Two Handle Bedpan Washer

For a two handle bedpan washer, repeat with the other check

valve and supply valve.

Turn the water off.

Remove any debris from the sprayer and reinstall.

Test and verify that the sprayer operates normally.

Face

Screw

Washer

Sprayer

1034408-2-A 6 Kohler Co.

Page is loading ...

Kohler K-13925-CP Installation guide

Brand: Kohler

Model: K-13925-CP

Category: Sanitary ware

Type: Installation guide

This manual is also suitable for

13925-CP

Kohler K-13925-CP Bedpan Washer is a versatile device designed to make cleaning medical equipment more efficient and hygienic. Its key features include:

Adjustable water flow: The water flow can be limited by adjusting the angle valve.
Adjustable water temperature: The water temperature can be reset by adjusting the angle valve.
Flexible hose: The flexible hose allows for easy maneuverability during cleaning.
Sprayer with multiple spray patterns: The sprayer can be adjusted to provide a variety of spray patterns, from a gentle mist to a powerful stream.
Easy installation: The Bedpan Washer comes with all the necessary mounting hardware and can be installed in minutes.

Download PDF

report

in other languages

français: Kohler K-13925-CP Guide d'installation
español: Kohler K-13925-CP Guía de instalación

Kohler K-13925-CP Installation guide

This manual is also suitable for

Kohler K-13925-CP Installation guide

in other languages

Related papers

Other documents