Kohler 13925-CP Installation guide

Category
Sanitary ware
Type
Installation guide

This manual is also suitable for

Kohler K-13925-CP Bedpan Washer is a versatile device designed to make cleaning medical equipment more efficient and hygienic. Its key features include:

  • Adjustable water flow: The water flow can be limited by adjusting the angle valve.
  • Adjustable water temperature: The water temperature can be reset by adjusting the angle valve.
  • Flexible hose: The flexible hose allows for easy maneuverability during cleaning.
  • Sprayer with multiple spray patterns: The sprayer can be adjusted to provide a variety of spray patterns, from a gentle mist to a powerful stream.
  • Easy installation: The Bedpan Washer comes with all the necessary mounting hardware and can be installed in minutes.

Kohler K-13925-CP Bedpan Washer is a versatile device designed to make cleaning medical equipment more efficient and hygienic. Its key features include:

  • Adjustable water flow: The water flow can be limited by adjusting the angle valve.
  • Adjustable water temperature: The water temperature can be reset by adjusting the angle valve.
  • Flexible hose: The flexible hose allows for easy maneuverability during cleaning.
  • Sprayer with multiple spray patterns: The sprayer can be adjusted to provide a variety of spray patterns, from a gentle mist to a powerful stream.
  • Easy installation: The Bedpan Washer comes with all the necessary mounting hardware and can be installed in minutes.
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems please don’t
hesitate to contact us. Our phone numbers and web site are listed on
the back cover. Thanks again for choosing Kohler Company.
Tools and Materials
Adjustable
Wrench
Strap
Wrench
Thread
Sealant
Plumbers
Putty
Phillips
Screwdriver
Blade
Screwdriver
Hex
Wrench
• 9/16" or larger drill
bit for wall material
• Piping support
brackets
• Rags
Plus:
1034408-2-A 2 Kohler Co.
Before You Begin
CAUTION: Risk of property damage. To support the bedpan
washer and piping, provide sufficient reinforcement or mounting
brackets as required inside the wall.
NOTE: Refer to the roughing-in diagram for dimensional
information.
Shut off the main valve and water supply.
Observe all local plumbing codes and building codes.
Plumb using 1/2 NPT pipe or 1/2 copper tubing, elbows, and
adapters. Secure the piping to reinforcements in the wall.
Provide the 1/2 pipe hole in the finished wall according to the
roughing-in diagram.
Provide screw holes, bracket, or other features as required for
supporting the flange onto the finished wall.
Kohler Co. reserves the right to make revisions in the design of
bedpan washers without notice, as specified in the Price Book.
1/2" N.P.T.
Inlet
3"
(7.62 cm)
3-1/2"
(8.9 cm)
Spray
Hose 48" (122 cm) Long
Spray 10-1/2" (26.7 cm)
Long
4-5/8"
(11.7 cm)
2-1/4"
(5.7 cm) D.
4-3/4"
(12.1 cm)
Kohler Co. 3 1034408-2-A
1. Install the Valve Body
NOTE: Apply a thread sealant where applicable.
Thread one supply nipple into the supply outlet in the wall.
Apply a bead of plumbers putty or other sealant to backside of
the flange according to the putty manufacturer’s instructions.
Slide the flange onto and over the supply nipple until it is snug
against the finished wall. Secure with the flange setscrew.
Remove any excess putty or sealant.
Rotate the valve body clamp to point straight out from the left
side of the valve body. Secure with a screw.
Slide the bell shaped flange onto the valve body holder. Do not
secure with the flange setscrew at this time.
Thread the valve body assembly onto the supply nipple. Ensure
that the valve body assembly is vertically aligned.
Slide the bell shaped flange down the holder until it is snug
against the finished wall. Secure with one flange setscrew and
two wall screws.
Screw
Screw
Screws
Flange
Supply
Outlet
Clamp
Holder
Supply
Nipple
Body
Flange
Apply Plumbers Putty.
1034408-2-A 4 Kohler Co.
2. Install the Hose Assembly
Thread one end of the flexible hose into the body assembly outlet.
Securely tighten.
Thread the other end of the flexible hose into the sprayer outlet.
Securely tighten.
Hang the spray nozzle from the rotated valve assembly clamp.
Key
Body
Assembly
Sprayer
Hose
Kohler Co. 5 1034408-2-A
3. Installation Checkout
NOTE: The water flow from the sprayer can be limited by adjusting
the angle valve.
NOTE: The water temperature can be reset by adjusting the angle
valve.
One Handle Bedpan Washer
For a one handle bedpan washer, turn on the main water supply.
Open both the check valve and the supply valve.
Check for leaks. Repair as needed.
Remove the screw, face, and washer from the sprayer.
Run water through the hose for approximately one minute to
remove debris.
Test and verify that the sprayer operates normally.
Two Handle Bedpan Washer
For a two handle bedpan washer, repeat with the other check
valve and supply valve.
Turn the water off.
Remove any debris from the sprayer and reinstall.
Test and verify that the sprayer operates normally.
Face
Screw
Washer
Sprayer
1034408-2-A 6 Kohler Co.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Kohler 13925-CP Installation guide

Category
Sanitary ware
Type
Installation guide
This manual is also suitable for

Kohler K-13925-CP Bedpan Washer is a versatile device designed to make cleaning medical equipment more efficient and hygienic. Its key features include:

  • Adjustable water flow: The water flow can be limited by adjusting the angle valve.
  • Adjustable water temperature: The water temperature can be reset by adjusting the angle valve.
  • Flexible hose: The flexible hose allows for easy maneuverability during cleaning.
  • Sprayer with multiple spray patterns: The sprayer can be adjusted to provide a variety of spray patterns, from a gentle mist to a powerful stream.
  • Easy installation: The Bedpan Washer comes with all the necessary mounting hardware and can be installed in minutes.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI