Aiwa CT-FX719M User manual

(msr

DIGITAL AUDIO

CT-FX729M w

CT”FX719 w

STEREO CAR CASSETTE RECEIVER

RADIO-CASSEITE ESTEREOFONICO PARA AUTOMOVIL

OWNER’S RECORD

For your convenience, record the model number and

serial number (you will find them on the right side of

your set) in the space provided below. Please refer to

them when you contact your AIWA dealer in case of

difficulty,

Model No. \CT-FX729M, CT-FX719

‘e”a’ ‘0 ~

Welcome

Thank you for your purchasing this AIWA product.

To optimize the performance of this unit, please

read through this manual carefully.

In addition to this operating instructions manual,

be sure to refer to the separate installation and

connections manuals as well.

PRECAUTIONS

● This unit is designed to be operated on a 12-volt

DC negative-ground electrical system only.

● To prevent short-circuiting, disconnect the

negabve car battery termmal until the unit has

been mounted and connected completely.

● When replacing the fuse, be sure to use one

whose amperage rating is identical. Use of a

fuse of higher amperage may cause serious

damage to the unit.

● Keep screwdrivers, etc. and other metallic or

magnetic objects away from the playback head.

● When your car was parked m direct sunlight

resulting m a considerable rise in temperature

inside the car, allow the unit to cool off before

operating it.

● Keep the volume at such a level that you can

hear outside warning sounds (horns, sirens,

etc.).

Notesoncassettes

Do NOT expose cassettes to direct sunlight,

extremely high or cold temperature or moisture.

Keep cassettes away from equipment with built-

in magnets to avoid unwanted noise or loss of

sound quality.

Do NOT touch the tape of a cassette, as any drl

or dust WIIIcontaminate the heads.

Be sure to remove any cassette from the unit If

you are not using it.

NOTE

This equipment has been tested and found to

comply with the limits fora Class B digital device,

pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable

protection against harmful interference In a

residential installabon.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may

cause harmful interference to radio

communications. However, there is no guarantee

that interference will not occur in a particular

installation. Ifthis equipment does cause harmful

interference to radio or television reception, which

can be determined by turning the equipment off

and on, the user is encouraged to try to correct

the interference by one or more of the following

measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the

equipment and receiver.

— Connect the equipment into an outlet on

circuit different from that to which the receiver

is connected.

— Consult the dealer or an experienced radio/

TV technician for help.

CAUTION

Modifications oradjustmentsto this product, which

are not expressly approved by the manufacturer,

may void the user’s right or authority to operate

this product.

1 ENGLISH

TABLE OF CONTENTS

FRONT PANEL ................................................................................................................................... 3

DETACHING AND ATTACHING THE FRONT PANEL ... ....... .... ....... .... ... ... .... .... .. ... ..... .. 4

SETTING THE CLOCK ....................................................................................................................... 5

RADIO OPERATION .......................................................................................................................... 5

PRESETTING STATIONS .................................................................................................................. 6

MY INFORMATION SWITCH ...... ... ... ... ... .... .... ........ ... ................... .. .... ........ .... .... ... ...... . 8

TAPE PLAYBACK ............................................................................................................................. 10

SOUND ADJUSTMENTS ................................................................................................................. 11

CD CHANGER PLAY (CT-FX729M only) ......................................................................................... 13

CONNECTING A PORTABLE CD/MD PLAYER OR OTHER EQUIPMENT 14

SETTING THE BEEP TONE ............................................................................................................. 15

SETTING THE CONTRAST CONTROL ........................................................................................... 15

TROUBLESHOOTING (CT-FX729M only) ............ .... ........ .... ..... ... ..... ......... .... .... ... ......... .... 16

MAINTENANCE ................................................................................................................................ 16

SPECIFICATIONS ............................................................................................................................ 17

This operating instructions manual covers the CT-FX729M andCT-FX719.

Their main differences are listed below.

CT-FX729M CT-FX719

CD changer (optional) control Yes

No

function

m

CT-FX729M

CT-FX719

$

Remote control

Supplied

Sold separately

q

* Refer to the operating instructions manual supplied with the AIWA RC-SW1 remote control for details.

The unit has an extra display (DEMO) mode which demonstrates the display of the operation modes of

the unit. The unit switches to DEMO mode automatically if you turn the unit on and leave it as it is for 5

seconds after all the connections have been completed.

To cancel

DEMOmode

During DEMO mode, press and hold DISP for more than 2 seconds.

To resume DEMO mode, press and hold DISP again for more than 2 seconds.

ENGLISH

2

FRONTPANEL

v??

123

Displaywindow

o

30

~ +/- (audio control) button

@

SEL (select) button

@

H-BASS button

@ DIR (direction) button

@CD

(CD changer playlpause) button*

(CT-FX729M only)

@ BAND button

@ OPEN

button

@

A.ME (auto memory/preset scan) button

o TUNE/DISC*

T/A buttons (CT-FX729M)

TUNE

7/A buttons (CT-FX719)

REW/FF (rewind/fast forward) buttons

@CD/MD IN jack (3.5-mm dia.)

@ MUTE/POWER OFF button

@ Preset station buttons 1-6

@ 144 (back skip) button* (CT-FX729M

only)

@ ~ (forward skip) button* (CT-FX729M

only)

@ INT (intro) button’ (CT-FX729M only)

@REP (repeat) button* (CT-FX729M only)

@ REP1 (repeat 1) button* (CT-FX729M

only)

@ RANDOM button* (CT-FX729M only)

@ DISP (display) button

@LO (local/DX) button

@MY INFO (my information) button

@ DRV (drivers sound stage adjustment)

button

@I Level indicator

@Tape/CD’ running indicator (CT-FX729M)

Tape running indicator (CT-FX719)

@CD changer operation indicator*

(CT-FX729M only)

@ST (stereo) indicator

@LO (local) indicator

@ HcBASS indicator

@MY INFO (my information) indicator

@ Main display section

@ DSSA (drivers sound stage adjustment)

indicator

‘ Usable only when an optional CD changer is

connected.

3 ENGLISH

DETACHING AND

ATTACHING THE FRONT

PANEL

1

2

You can detach the front panel from the unit and

carry it with you when you leave your car

unattended.

When you carry the front panel out of your car,

use the supplied carrying case,

I Press and hold MUTE for more than 2

seconds to turn the unit off.

z Press OPEN to open the front panel

and pull it out as illustrated @)- @).

Notes

● When you leave the front panel open, do not put

anything on the panel.

● When you cany the front panel in the carrying

case, do not drop or apply mechanical shock to

the panel, and never let the panel become wet.

Attachingthefrontpanel

I Fit the lower side of the front panel to

its hinge pegs as illustrated @)-@.

/

2 Close the front panel.

---

!.,

Notes

● Donot press OPEN by accident when you push

the front panel to secure it in above procedure.

● Do not touch the connector on the reverse side

of the front panel, as doing so may contaminate

the connector and cause a poor connection

resulting in a malfunction.

SecurityLamp

When the front panel is detached, you can find an

LED lamp on the front side of the unit. This lamp

is designed to deter theft, and continues to flash

when the front panel is detached. This unit is not

equipped with any other security systems such

as a secu rity alarm, so there are limitations to its

effactiveness.

LED lamp

ENGLISH

4

SETTING THE CLOCK

RADIO OPERATION

4 1,2

1,3

DISP

2

You can turn the unit on by pressing any button

except OPEN on the front panel.

I With the unit on, press and hold SELfor

more than 2 seconds until the clock

indication appears.

1

2

2 Press TUNE v to set the hour.

Press TUNE A to set the minute.

3 Press SEL to start working the clock

from Osecond.

Havingtheclockdisplayedwhile in Radio,Tape

PlayorCDChangerPlaymode

Press DISP repeatedly until the clock isdisplayed.

The clock display appearsfor5 seconds, then the

unit returns to its former display.

Each time you press DISP, the display changes

as follows,

T

Radio~ape Play/CD Changer Play indication

J

Clock

3

4

3

Press BAND to turn the radio on.

The radio frequency appears.

Press BAND again to select the band

from among FI (FM1), F2 (FM2), F3

(FM3), Al (AM1) and A2 (AM2).

The band indications appear cyclically in

order.

● F1, F2 and F3 share the same frequency

range.

● Al and A2 share the same frequency range.

Band indication Frequency(ndication

Press (more than 2

seconds) either

TUNE 7 orTUNE Atotuneinthedesired

station.

The unit starts scanning and tunes in a station

automatically (seek tuning).

Press TUNE Y to decrease and TUNE A to

increase the frequency.

Press the button again to cancel seek tuning.

Repeat the procedure until the desired station

is tuned in.

Note

If you press (less than 0.5 second at a time)

either TUNE Y or TUNE

A, the frequency

decreases or increases step by step.

Adjust the volume with +/-.

5 ENGLISH

TUNET/A

CD BAND

MUTE DIR LO

Toturn the unit off

Press and hold MUTE for more than 2 seconds.

Note

The unit turns on in the last mode selected when

you turned off the unit with the exceptions of

pressing the following buttons.

●Pressing DIR turns on the unit in Tape Play

mode.

●Pressing CD turns on the unit in CD Changer

Play mode.

● Pressing BAND turns on the unit in Radio mode.

Switchingmodes

When the unit is in Radio or CD Changer Play

mode, inserting a cassette switches the unit to

Tape Play mode automatically.

LO(local/DX)button

You can use Local mode when you wish to tune

in only strong stations during seek tuning. In

Radio mode, press LO to select Local mode. The

“LO indicator lights up.

● Press LO to cancel Local mode and switch to

DX (distance) mode.

● The “ST (stereo) indicator lights up when the

tuned-in station is broadcasting in stereo and

the reception is good.

PRESETTING STATIONS

21

1 Press BAND to select a desired band

from among F1

(FM1 ), F2 (FM2), F3

(FM3), Al (AM1) and A2 (AM2).

z Press and hold A.ME for more than 2

seconds to activate the automatic

presetting function.

The six strongest available stations will be

stored inmemory on the preset station buttons

1 to 6 in order of their signal strength, The “A

MEW indication appears while the unit is in

this mode.

Use this function to automatically preset up to 6

stations each for F1, F2, F3, Al and A2 (up to a

total of 30 stations).

● When auto memory is completed, the preset

stations are automatically tuned infor5 seconds

each in order.

● To stop auto memory, press A.ME again.

Tocheckthepresetstations(presetscan)

● If you wish to check the preset stations, press

A.ME forlessthan 2seconds. The preset stations

stored in memory will be tuned in for 5 seconds

each in order.

● To stop this function, press A.ME again or press

any of the preset station buttons 1 to 6.

imml

ENGLISH 6

PRESETTING STATIOiIIS

You can manually preset stations that have not

been selected by auto memory.

21

1

2

3

Prese BAND to select the band from

among F1 (FM1), F2 (FM2), F3 (FM3), Al

(AM1) and A2 (AM2).

Tune in the station that you wish to

preset with TUNE T or TUNE A.

Press one of the preset station buttons

1 to 6 for appro~mately 2 seconds.

The number of the pressed preset station

button appears next to the frequency

indication.

Repeat these procedures to preset up to 6stations

each for Fl, F2, F3, Al and A2.

● If you try to preset a station on a preset station

button on which another station of the same

band has already been preset, the previously

meset station will be erased.

1

2

~ Press BAND to select a desired band

from among F1 (FM1), F2 (FM2), F3

(FM3), Al (AMI) and A2 (AM2).

z Press the desired preset station button.

The number of the pressed preset station

button appears next to the frequency

indication.

Active tuning reception control (ATRC)

This unit automatically suppresses FM noise

caused by varying signal strength resulting from

movement of the car.

● The built-in automatic blending circuit mixes the

left and right channel signals according to the

strength of the reception. At the same time, the

high-cut circuit activates to maintain the sound

quality.

● Ifthe reception becomes even weaker, the unit

automatically switches to Monaural mode to

reduce noise.

During presetting of stations, beeps are heard

regardless of the beep on/off setting (page 15).

7 ENGLISH

MY INFORMATION

SWITCH

You can timer-activate the radio for up to two

daily radio programs. The unit turns on and off in

Radio mode at the preset time automatically,

3,5,7,9

4,8,106

2

1

1 With the unit off, press and hold MY

INFO for more than 2 seconds.

The “PROGRAM1” or “PROGRAM2”

indication flashes in the display window.

The numberon which no program

is presetflashes,

2 Press either of preset station button 1

or 2 to select program 1 or 2.

3 Press SEL.

The “ON TIME indication flashes

Press SEL again.

Timer indication flashes.

4

5

6

7

8

9

Set the time you wish the unit to turn on

in Radio mode.

PressTUNE Y

to set the hour.

Press TUNE A to set the minute,

Press SEL.

The “BAND SEL” indication flashes.

Press SEL again.

Radio indication flashes.

Band indication

Press BAND to select the band.

Press SEL.

The “FREQ indication flashes.

Press SEL again.

Radio indication flashes.

Frequencyindication

Tune in the station that you wish to

preset with TUNE 7 or TUNE A.

P~ess SEL.

The “OFF TIME indication flashes,

Press SEL again.

Timer indication flashes.

lo Set the time you wish the unit to turn

off.

PressTUNE 7

to set the hour.

Press TUNE A to set the minute.

mm

ENGLISH 8

MY INFORMATION SWITCti

11

12

~~

Press SEL.

The clock indication appears.

22

Press MY INFO.

Your setting is stored in memory and the unit

turns off.

● If you preset another program, repeat all the

steps from step 1.

● To cancel a timer setting in progress, press and

hold MUTE for more than 2 seconds.

You can activate the timer for program 1 and/or

program 2.

2f4

1

2

3

4

5

Tocancelthe timer

To cancel program 1, press TUNE 7 or TUNE A

repeatedly until the “PRG1 OFF indication flashes

in step 2.

To cancel program 2, press TUNE Y or TUNE

A

repeatedly until the “PRG2 OFF” indication flashes

in step 4.

Noles

● When you preset two programs, be sure that

they do not overlap.

● Even if the unit is in a mode other than Radio

mode, the unit switches to Radio mode and

tunes in the preset radio program at the preset

time automatically. When the program is over,

the unit returns to the former mode automatically.

● When this function is activated, TUNE 7/A,

A.ME, LO and the preset number buttons do not

work for tuning in stations.

● Even if you are listening to a radio program with

this function, pressing the following buttons

switches the unit to other mode:

— Pressing BAND changes the unit to Radio

mode.

— Pressing DIR changes the unit to Tape Play

mode.

— Pressing CD changes the unit to CD Changer

Play mode.

If you switch modes with these buttons, the unit

does not turn off at the turn-off time of the timer.

To switch to CD/MD IN mode, press DIR, CD, or

BAND before connecting a portable CD/MD

player, etc. to the CD/MD IN jack.

1,3,5

With the unit on, press MY INFO.

The “PRGI ON” or ‘{PRGI OFF indication

(the current setting for program 1) appears.

Press TUNE T or TUNE A repeatedly

until the “PRG1 ON” indication flashes.

Press MY INFO.

The “PRG2 ON or “PRG2 OFF indication

(the current setting for program 2) appears.

Press TUNE 7 or TUNE A repeatedly

until the “PRG2 ON” indication flashes.

Press MY INFO to activate the timer.

The “MY INFO indicator lights up,

If you do not proceed to the next step within 5

seconds in steps 1 – 4, the display returns to the

current source indication.

9 ENGLISH

Press the following buttons to operate tape

TAPE PLAYBACK

3 1

DIR

1

2

3

Press OPEN to open the front panel

and insert a cassette.

Playback starts in the direction that the unit

played back previously.

A (eject) button

Close the front panel,

Tape runningindicator

Adjust the volume with +/-.

Notes

● If a cassette is already inserted, press DIR to

start playback.

● Be sure to close the front panel after inserting or

ejecting a cassette.

transporl.

To do this

Eject the cassette

Change the playback

side

Stop fast-forwarding or

rewinding and resume

playback

Fast-forward either side

of the tape

Rewind either side of

the tape

Stop the tape and turn

the unit off

Pressthis button

@

(for more than

2 seconds)

● At the end of the tape in Fast Forward mode, the

other side of the cassette will start playing

automatically.

● At the end of the tape in Rewind mode, the same

side will start playing automatically.

Direction indications

=

F~J] Displayed when the upper side of the

p~i’ Displayed when the lower side of the

Tape transport display

When you start tape playback, the transport

display indicates the tape movement.

Upper side: During playback,

fast-fowarding

Lower side: During rewindina

Lower side: During playback,

fast-fowarding

Upper side: During rewinding

During fast-forwarding or rewinding, the transport

display accelerates.

Before turning the ignition off

Be sure to eject any cassette from the unit before

turning the ignition off.

mm

ENGLISH 10

TAPE PLAYBACK

SOUNDADJUSTMENTS

Switching modes

When the unit is in Radio or CD Changer Play

mode, inserting a cassette switches the unit to

Tape Play mode automatically.

Topreventtapeproblems

Before inserting a cassette into the unit, make

sure that there is no slack inthe tape. If necessary,

take up the slack by inserting a pencil into the

spindle hole and winding.

Tapes of 90 minutes or longer are extremely thin

and easily deformed or damaged. They are not

recommended.

22

1

2

MUTE

Press SEL to select the mode that you

wish to adjust from: VOL (volume),

BASS (bass), TRE (treble), BAL

(balance) and FAD (fader).

The following indications appear in cyclic

order.

If you do not proceed with step 2 within 5

seconds, the selected mode is canceled, and

the indication returns to the current source

mode.

Press +/– to adjust the level.

Press and hold either button to change the

level rapidly.

+

Decreases the

Increases the

volume level

Decreases the

Increases the

bass level

Decreases the

Increases the

treble level treble level

Decreases the Decreases the

level of the right level of the left

speaker(s) speaker(s)

Decreases the

level of the front level of the rear

speakers

Without selecting any mode with SEL, only

the volume level can be adjusted by pressing

+/–.

MUTE button

Press this button to temporarily Iowerthevolume.

Press it again to restore the previous volume.

11 ENGLISH

You can adjust the position of sound stage and

tone balance to best serve a particular seat just

by pressing DRV.

DRV

Press DRV to change the position of sound

stage.

Each time you press

changes as follows.

DRV, the sound stage

FL

For the front left seat

= R For the front right seat

You can enjoy music with strong bass sound.

H-BASS

Press H-BASS to obtain powerful bass.

Each time you press H-BASS, the bass sound

level changes as follows.

[

OFF

L

H-BASS 1 LOW

J

H-BASS 2 Medium

J.

H-BASS 3 High

When H-BASS isactivated, the” -” indicator

lights up,

Note

When DRV is activated, you cannot adjust BAL

(balance), FAD (fader), BASS (bass) and TRE

(treble) modes.

ENGLISH

12

CD CHANGER PLAY

(CT-FX729M only)

You can play discs with this unit by connecting

the optional AIWA ADC-EX1 06, ADC-M60 CD

changer. Make sure that the disc magazine

loaded with the discs is inserted in the connected

CD changer.

To install the unit, refertotheseparate Installation

and Connections manual.

2 1

1 Prees CD to start playing from disc 1.

The disc and track numbers appear.

CD running

CDchanger

indicator operation indicator

Disc nu~ber Track’number

z Adjust the volume with +/-.

DISCV/A CD BAND

MUTE ~ M INT ] REP1 I DIR

REP RANDOM

Press following buttons to operate the connected

CD changer.

Toswitchmodes

● To turn the unit off, press and hold MUTE for

more than 2 seconds.

● Even if the unit is in Radio or Tape Play mode,

pressing CD switches the unit to CD Changer

Play mode.

● Ifyou wish to switch to another mode, press the

following buttons.

– Pressing DIR switches the unit to Tape Play

mode.

- Pressing BAND switches the unit to Radio

mode.

To skip tracks

Buttons

Press* Press and hold

w Skips to the next Advances

track rapidly

Release it to

resume play

M

Skips back to

Reverses

the beginning of rapidly

the current track Release it to

resume play

* Press for less than 0.5 second,

Toplayotherdisc

To start playing the previous disc in the disc

magazine, press DISC T.

To start playing the next disc, press

DISC

A.

The number of the disc appears,

Repeat play

To repeat the current track, press REP1 (the

“REPEAT 1” indication appears).

To repeat the current disc, press REP (the

“REPEAT” indication appears).

To cancel either mode, press the same button

a9ain-

Introplay

Press INT (the “SCAN indication appears). The

first 10 seconds of each track on all the discs in

the disc magazine are played in sequence.

To cancel Intro play, press INT again.

To do this I Press this button

To pause

To resume

I

@@

13 ENGLISH

Randomplay(ADC-EX106,ADC-M60only)

Press RANDOM (the “RANDOM” indication

CONNECTING A

appears).

All the tracks on the current disc are played in

PORTABLE CD/MD

random order.

To cancel Random play, press RANDOM again.

PLAYER OR OTHER

EQUIPMENT

This unit is equipped with a line-level input (CD/

MD IN) jack, enabling high sound quality.

m

I

1

2

Connect a portable CD/MD player, etc.

via the CD/MD IN jack (3.5-mm dia.) on

the unit.

Start playback from the connected

equipment.

The “CD IN” indication appears.

● For further information on the portable CD/MD

player, etc., refer to the operating instructions

for the equipment.

Notes

● Connecting a plug to the CD/MD INjack cancels

Radio, Tape Play and CD Changer Play mode

and activates CD/MD IN mode. Disconnecting

the plug cancels CD/MD IN mode and returns

the unit to its former status.

● When thetimeris activated (page 9), connecting

a plug to the CD/MD INjack does not switch the

unit to CD/MD IN mode. Press DIR, CD, or

BAND before connecting the plug to the CD/MD

IN jack.

ENGLISH 14

SETTING THE BEEP TONE

The unit is preset at the factory to beep each time

you press any button on the front panel except

OPEN. You can stop beeping by following the

procedure below.

1,3

1

2

3

2

With the unit off, press and hold SELfor

more than 2 seconds.

Press TUNE T or TUNE A repeatedly to

select “BEEP ON” or “BEEP OFF”.

Press SEL.

SETTING THE CONTRAST

CONTROL

You can change the contrast of the display.

1

2

1 With the unit on, press and hold DRV

for more than 2 seconds.

The current contrast indication appears.

z Press TUNE v or TUNE

A repeatedly to

select the contrast from among the

following three levels.

L

‘$

CONT.M (factory setting)

t

CONT.H

15 ENGLISH

TROUBLESHOOTING

(CT-FX729M only)

Errorcodes

In the following cases the corresponding error

code indication appears. Follow the suggestions

below to solve the problem, If the error code

indication does not disappear, consult an AIWA

service center.

ERRORO1

ERROR02

ERROR03

ERROR04

ERROR05

The disc magazine is not properly

inserted inthe CD changer. Reinserl

the magazine.

Refer to the

instruction manual for the CD

changer.

No discs are loaded in the disc

magazine. Insert discs properly.

Refer to the instruction manual for

the CD changer.

Focus error. Check that the discs

are loaded properly in the disc

magazine (right side up, etc.).

Problem with the CD changer, Reset

the unit by pressing the reset button.

If this does not solve the problem,

consult an AIWA service center.

The CD changer is overheated.

Allow the cha;ger to cool off by

moving the vehicle out of direct

sunlight,

Resetbutton

The Reset button is visible when you detach the

front panel. Tty pressing this button if aconnected

CD changer does not operate properly, To press

this button, use the tip of a pointed object such as

a pencil or toothpick.

Note that all your setting stored in memory,

however, will be erased by pressing this button.

MAINTENANCE

Cleaning the front panel

When the front panel is soiled, wipe the surface

of the panel with a soft, dry cloth,

Cleaning the tape head

Use a cleaning cassette to clean the playback

head and capstans approximately once a month,

If the playback head is dirty, the high tones may

not be reproduced properly.

Cleaning the connector

The connector on the reverse side of the front

panel needs to be cleaned occasionally. Wipe

the surface of the connector with a cotton swab

slightly moistened with alcohol.

Resetbutton

MGL/5H16

SPECIFICATIONS

RADIO SECTION

(FM)

FrequencyRange:

87.5 MHz– 108 MHz

(100-kHzsteps)

87.5

MHz – 108 MHz

~;k~t-feteps)

Usable Sensitwlty

50 dB Quieting Sensitivity

17,2 dBf

IF Rejection:

80 dB

Frequency Response 30 Hz – 15,000 Hz

S/N Ratio:

63 dB

Stereo Separation:

35 dB at 1 kHz

Alternate Channel Selectivity

Capture Ratio

(AM)

Frequency Range,

Usable Sensitivity

TAPESECTION

Tape Speed:

S/N Ratio,

70 db

3 dB

530 kHz – 1,710 kHz

(1O-kHz steps)

531 kHz – 1,602 kHz

(9-kHz steps)

30 pV (30 dB)

4,8 cm/sec. (1

7/8ips)

50 dB

Frequency Response: 40 Hz – 14,000 Hz

Stereo Separabon:

40 dB

FF/REW Time.

95 sec. (C-60)

AUDIO SECTION

Max. Power Output 40 W x 4 channels

CD/MDIN input

Input sensitivity (load impedance)

CDIMD IN:

500 mV (1O kfl)

GENERAL

Power-Supply Voltage:

14.4 V (11 to 16 V allowable),

DC, negative ground

Load Impedance, 4 Q

Tone Control:

Bass ~10 dB at lr)r)

HZ

Treble *IO dB at 10 kHz

Preemp Output Voltage (load Impedance):

CT-FX729M: 40 V (10 kQ)

CT-FX719: 2.2 v (lo m)

Installation size:

182 (W) x 53 (H) x 155 (D) mm

(7 l/. (W)X21/8 (H)X61/8

(D)

inches)

Accessory supphed: Carryingcaee (1)

● Specifications and external appearance are

subject to change without notice due to product

improvement.

17 ENGLISH

Page is loading ...

INDICE

PANEL DELANTERO ......................................................................................................................... 3

DESMONTAJE E INSTALACION DEL PANEL DELANTERO ... .. .... .... ... .... .... .. ... ... .... ... . 4

AJUSTE DEL RELOJ .......................................................................................................................... 5

FUNCIONAMIENTO DE LA RADIO ................................................................................................... 5

PROGRAMACION DE LAS ESTACIONES ... ... .... .... .. ... .... .... .... ... . .... ... ... ... ... ... .. 6

INTERRUPTOR DE INFORMATION PROPIA ................................................................................... 8

REPRODUCTION DE LA CINTA ..................................................................................................... 10

AJUSTES DEL SONIDO ................................................................................................................... 11

REPRODUCTION CON CAMBIADOR DE DISCOS COMPACTOS (solo en el CT-FX729M) ........13

CONEXION DE UN TOCADISCOS DE DISCOS COMPACTOS/MINIDISCOS PORTATIL U

OTRO EQUIPO .... .. ..... ............ .... ....... .... .... ... ... .... ... .... .... .. .... .... .. ... ... .. .. ....... 14

AJUSTE DEL TONO DEL TIMBRE ... .. .... .... ... ... ... .. .... ... .... ... ... ... .. ... ... .. ... ... . 15

AJUSTE DEL CONTROL DE CONTRASTE .. ... ... .... .. ... .... .. ... ... ... ... .... .. .. ... .... 15

LOCALIZATION DE AVERIAS (solo en el CT-FX729M) ... ... ..... .... .. .... .... ... ... ... ... .... ..... 16

MANTENIMIENTO . .... ... .... ... .. ... .... .. ..... .... .. .. ... .... .... .... .. .. .... .. .... .... ........ ..... 16

ESPECIFICACIONES ....................................................................................................................... 17

Este manual de instrucciones explica el funcionamiento del CT-FX729M y CT-FX71 9,

A continuation sedan Ias principals diferencias entre ambos.

CT-FX729M CT-FX719

Funcion de control del

Si

No

cambiador de discos

compactos optional

m

...

u)

CT-FX729M

CT-FX719

w

>

Control remoto

Incluido’ De venta por separado

z,

g

* Para mas detalles, consulte el manual de instrucciones que viene con el control remoto RC-SW1 de

AlWA,

El aparato tiene un modo de indicaci6n adicional (DEMO) para demostrar Ias indicaciones de Ios modos

de funcionamiento de este aparato. El aparato cambia automaticamente al modo DEMO cuando se

presiona el interruptor principal durante 5 segundos despues de completar todas Ias conexiones.

Para salir del modo DEMO

Durante el modo DEMO mantenga presionado DISP durante mas de 2 segundos.

Para continuar con el modo DEMO, mantenga presionado nuevamente DISP durante mas de 2

segundos.

ESPANOL

2

Page is loading ...

TABLE DES MATIERES

PANNEAU FRONTAL ......................................................................................................................... 3

DETACHEMENT ET FIXATION DU PANNEAU AVANT .................................................................... 4

REGLAGE DE L’HORLOGE .... ... ... .... ........ .... .... ... .... .... ... .... .... ... ....................... ........ ..... . 5

FONCTIONNEMENT DE LA RADIO .................................................................................................. 5

PREREGLAGE DES STATIONS .................................. ........ .............. ..... ............. ... .. ..... .... ... .. 6

FONCTION MES INFORMATIONS ....... ....... .... ....... .... ... .... .... .. .... .... ........ .... .... ... .... ..... . 8

LECTURE DE CASSETTE . .... ............ ........ .... ........ .... .... ............. ... ... ... ... .... .... ... .... .... 10

AJUSTEMENTS DU SON ................................... ...................... .... .... ... .... ............. .... ... .... ...... 11

LECTURE DE CHANGEUR DE CD (CT-FX729M seulement) ......................................................... 13

RACCORDEMENT D’UN LECTEUR DE CD/MD PORTABLE OU D’UN AUTRE APPAREIL ......... 14

REGLAGE DE LA TONALITE BIP 15

REGLAGE DE LA COMMANDE DE CONTRASTE .......................................................................... 15

DEPANNAGE (CT-FX729M seulement) ........................................................................................... 16

ENTRETIEN ...................................................................................................................................... 16

SPECIFICATIONS ............................................. ....... .... ..... ...................... .... ........ .... .... ... ....... 17

Ce mode d’emploi couvre Ie CT-FX729M et Ie CT-FX71 9.

Les principals differences entre Ies deux sent indiquees ci-dessous.

CT-FX729M CT-FX719

1

Fonction de ContrOle du

Oui

Non

changeur de CD en option

CT-FX729M

CT-FX719

Telecommande

Fournie’ Vendue separement

*Voir Ie mode d’emploi fourni avec la telecommande RC-SW1 AIWA pour Ies details.

Get appareil est dote d’un mode d’affichage (DEMO) sp6cial qui fait une demonstration des modes

d’exploitation de I’appareil. II commute automatiquement au mode DEMO s’il est mis sous tension et

Iaisse tel quel 5 secondes apres la fin de toutes Ies connexions,

Pour annuler Ie mode DEMO

En mode DEMO, presser et maintenir enfonce DISP pendant plus de 2 secondes.

Pour revenir en mode DEMO, presser et maintenir enfonce une seconde fois DISP pendant plus de 2

secondes.

FRAN(?AIS

2

Page is loading ...

Aiwa CT-FX719M User manual

Aiwa CT-FX719M User manual

in other languages

Related papers

Other documents