Powermate PM0496500 User manual

Brand: Powermate

Model: PM0496500

Category: Power generators

Type: User manual

Page is loading ...

*13 HP Honda OHV engine

*Cast-iron cylinder sleeve

*Low oil sensor

*Receptacles on control panel

*CordKeeper™

*8 gallon plastic fuel tank

*Portability Kit

A.120 V, 20 Ampere Duplex Receptacle

This duplex is split so that 20 amps of current may be

drawn from each half of the receptacle. However, total power

drawn must be kept within nameplate ratings. These

receptacles may be used along with the twistlock receptacle

provided the generator is not overloaded.

B.120/240 V, 30 Ampere Twistlock Receptacle

A maximum of 30 amps may be drawn from the 120/240

volt receptacle, provided it is the only receptacle used.

However, current must be limited to the nameplate rating. If the

120/240 volt receptacle is used along with the 120 volt

receptacle, the total load drawn must not exceed the nameplate

ratings.

C.Circuit Breakers

The receptacles are protected by an AC circuit breaker. If

the generator is overloaded or an external short circuit occurs,

the circuit breaker will trip. If this occurs, disconnect all

electrical loads and try to determine the cause of the problem

before attempting to use the generator again. If overloading

causes the circuit breaker to trip, reduce the load. NOTE:

Continuous tripping of the circuit breaker may cause

damage to generator or equipment. The circuit breaker may

be reset by pushing the button of the breaker.

D.Engine On/Off Switch

E.CordKeeper™ Restraint

The CordKeeper™ restraint is a unique feature used to

prevent plugs from being pulled out of the receptacles.

This product is warranted by Powermate Corporation to the

original retail consumer against defects in material and

workmanship for a period of two (2) years from the date of retail

purchase and is not transferable. This two year warranty

applies only to products used in consumer applications. If this

generator is used in a commercial application, then the period

of warranty coverage is limited to one (1) year from the date of

purchase.

Please complete and return the enclosed Customer

Information Card so that we can reach you in the unlikely event

a safety recall is needed. Return of this card is not required to

validate this warranty.

WHAT IS COVERED: Replacement parts and labor.

WHAT IS NOT COVERED: Transportation charges to

Powermate Corporation for defective products. Transportation

charges to consumer for repaired products. Brushes, fuses,

rubber feet, and receptacles. Damages caused by abuse,

accident, improper repair, or failure to perform normal

maintenance. Power units or engines which are covered

exclusively by the warranties of their manufacturer. Sales

outside of the United States or Canada. Any other expense

including consequential damages, incidental

damages, or incidental expenses, including damage to

property. Some states do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation

or exclusion may not apply to you.

IMPLIEDWARRANTIES: Any implied warranties, including

the Implied Warranties of Merchantability and Fitness For A

Particular Purpose, are limited in duration to one (1) year from

the date of retail purchase. Some states do not allow

limitations on how long an implied warranty lasts, so the above

limitation may not apply to you.

HOW TO OBTAIN WARRANTY PERFORMANCE:

Replacement parts and service are available from Powermate

Corporation Service Centers. Locate your nearest Service

Center by calling TOLL FREE 1-800-445-1805. In the unlikely

event a Service Center can not be located you may call

Powermate Corporation for a return authorization number. Any

unit returned WITHOUT an authorization number will be

refused.

To the extent any provision of this warranty is prohibited by

federal, state, or municipal law, and cannot be preempted, it

shall not be applicable. This warranty gives you specific rights,

and you may also have other rights which vary from state to

state.

English

CONTROL PANEL

MAJOR GENERATOR FEATURES

LIMITED WARRANTY

(NOT VALID IN MEXICO)

TOOLS REQUIRED: 7/16”, 1/2” and 9/16" sockets and ratchets, block(s) of wood (minimum of 6” tall).

Refer to the parts list on page 9.

WHEEL INSTALLATION

1.Block up end of generator opposite the fuel tank cap to install wheel kit.

2.Insert wheel spacer (item 45) into the center of the wheel (item 31).

3.Slide 3/8 x 4.25” bolt (item 35) and 3/8 washer (item 30) through the wheel (item 31), then through the wheel bracket on the

carrier, with the offset side of the wheel hub against the wheel bracket.

4.Thread 3/8 nyloc nut (item 36) onto the bolt and tighten to securely clamp the wheel assembly to the carrier.

5.Repeat above instructions for the remaining wheel.

FOOT INSTALLATION

1.Assemble the rubber feet (item 32) to the foot bracket (item 49) using a 1/4-20 x 1.5” bolt (item 48). Thread a 1/4 washer

(item 39) and a 1/4 nyloc nut (item 13) to the bolt to secure the assembly. Caution: Do not over tighten so that the foot

material collapses.

2.Blocking up the alternator side of the generator, place the foot bracket under the carrier channel. Thread a 5/16-18 x 1” bolt

(item 47) with a 5/16 wide washer (item 34) through the mounting holes and thread a 5/16 wide washer (item 34) and a 5/16

nyloc nut (item 16) to the bolt to secure the foot bracket to the carrier.

HANDLE INSTALLATION

1.Place handle (item 28) over carrier on same end as feet, as shown in the diagram.

2.Slide 5/16 x 2.25” bolt (item 29) and 5/16 washers (item 15) through handle as shown in diagram and secure with 5/16” nyloc

nut (item 16). Tighten until handle is securely clamped to the carrier.

3.Apply aerosol hairspray or similar adhesive to the handle (item 28), and then slide the handle grip (item 46) onto the handle.

The aerosol hairspray will allow for easier assembly and will adhere the grip to the handle.

4.Insert cap (item 38) into end of handle (item 28).

5.Repeat above instructions for the remaining handle.

LOCKING HANDLE

1.Attach the lanyards (item 33) to the release

pins (item 37) and carrier as shown in the

illustration.

2. To lock the handle (item 28) in the extended

position, align the holes in the handle brackets

with the holes in the carrier brackets and insert

the release pins (item 37).

English

PORTABILITY KIT INSTALLATION

3733

Page is loading ...

REF.PARTDESCRIPTION DESCRIPTION DESCRIPCIÓNQTY

NO.NO.

10062896Carrier, assemblyEnsemble transportTransportador, conjunto1

2Note AEngine 13 hp Honda OHVMoteurMotor1

30051094IsolatorSectionneurAislador4

40050236.01Adapter, engineAdaptateur pour moteurAdaptador, motor1

50000919.01Bolt whz 3/8-16 x .75BoulonPerno4

60062933Stator 6.5 KW 60 HZStatorEstator1

6A0056719Connector, statorConnecteur, statorConector, estator1

6B0050401Connector, panelConnecteur, tableauConector, panel 1

6C0062466Connector plugPrise de connecteurTapón del conector1

70052293Rotor 6.5 KW RotorRotor1

80049613.01Bolt, hex 5/16-24 x 8.69BoulonPerno1

9Note BWasher, lock 5/16Contre-écrou 5/16Arandela, de cierre 5/163

100062470Endbell Wired Couvre-enroulement, câblage completCaja posterior con cable

tableau1

10A0050439Brush, E-4RBalais, E-4REscobilla, E-4R2

10B0062455Assembly, bridge rectifierEnsemble de planche de Conjunto de la tabla del rectificador del puente

boardredresseur de pont1

10C0062264Brush CoverCouvre-balaisCubierta de escobillas1

110035170Bolt, hex hd 1/4-20 x 8BoulonPerno4

120008854Lug, groundOeillet de mise à la terreTerminal, tierra1

130040832Nut, nyloc 1/4-20Écrous nyloc 1/4-20 Tuerca, nyloc 1/4-20 11

14Note BBolt, 5/16-18 x 1 1/2BoulonPerno2

15Note BWasher, flat 5/16Rondelle plates 5/16Arandela, plana 5/169

160048736Nut, nyloc 5/16-18Écrous nyloc 5/16-18Tuerca, nyloc 5/16-189

170049224Assembly, ground wireEnsemble fil de masse tressé a tierraConjunto, cable trenzado 1

18Note BWasher, star external 5/16Rondelle à dents externa 5/16Arandela, estrella 2

19Note BBolt, hex 5/16-18 x 3/4Boulon, tête hex 5/16-18 x 3/4Perno1

0057664MufflerSilencieuxSilenciador1

210061392GasketJointEmpaquetadura1

220062897Panel, wiredTableau complet câbléPanel, cabeado completo1

22A0049071Circuit Breaker 20 ampDisjoncteurs 20 ampCortacircuitos 20 amp2

22B0049382Circuit Breaker 30 ampDisjoncteurs 30 ampCortacircuitos 30 amp2

230062462Screw #6-20 x .38 Type BVisTornillo4

240062694

Shield, heatÉcran de chaleurPantalla para el calor1

25Note CFuel tank assemblyEnsemble complet du réservoirConjunto tanque1

25A0056231Fuel CapCapuchonTapa de combustible1

25B0049114Fuel shut off with filterRobinet de carburantVálvula combustible con filtro1

25C0051102Fuel filterFiltre à carburantFiltro combustible1

25D0062673Fuel BushingBague d’essenceBuje de combustible1

0055982.01Cord Keeper

Cord Keeper

270048243Bushing, stepBagues de reeduction à gradins Casquillo, paso4

280062706HandlePoignéeManija2

29Note BBolt, 5/16-18 x 2 1/4BoulonPerno2

30Note BWasher, flat 3/8Rondelle plates 3/8Arandela, plana 3/82

310057704WheelRoueRueda2

320055894Rubber FootPiedPie2

330062174LanyardLanyardAcollador2

340049352Washer, flat 5/16 WRondelle plates 5/16 largeArandela, plana 5/16 lejos8

35Note BBolt, 3/8-16 x 4.25BoulonPerno2

360057578Nut, nyloc 3/8-16Écrous nyloc 3/8-16Tuerca, nyloc 3/8-162

370062502Pin, releaseEpingle de relâchementAlfileres de la liberación2

380058955Cap, plasticCapuchonTapa2

39Note BWasher, flat 1/4Rondelle plates 1/4Arandela, plana 1/47

400056342Bracket, statorSectionneur statorConjunto de soporte1

410049279Bolt, whz 5/16-18 x 1/2BoulonPerno3

420000901.01Bolt, whz 5/16-24 x 5/8BoulonPerno2

430061393Nut whz 8mmÉcrousTuerca2

440050298Switch, RockerInterrupteurInterruptor1

450062433Wheel spacerBague d’espacement Espaciador de la rueda2

460062495Grip, handlePoignéeEmpuñadura2

47Note BBolt, 5/16-18 x 1BoulonPerno2

48Note BBolt, 1/4-20 x 1 1/2BoulonPerno2

490062301Bracket, footSupport de piedSoporte del pie1

500052931J clampCollierPinza vinílica1

51Note BBolt, 1/4-20 x 1 1/4BoulonPerno1

PARTS LIST / LISTE DES PIÈCES / LISTA DE PIEZAS

Note A:

Powermate Corporation

will not provide engines as replacement parts. Engines are covered through the engine manufacturer's warranty. Consult the accompanying

engine manual or contact our service department for assistance.

Note B:

These are standard parts available at your local hardware store.

Note C:

Contact your nearest

Powermate Corporation

Service Center for replacement fuel tanks.

WARNING: To avoid possible personal injury or equipment damage, a registered electrician or an authorized service representative should

perform installation and all service. Under no circumstances should an unqualified person attempt to wire into a utility circuit.

Electrical: For models approved for the City of Los Angeles, the ampacity of the phase conductors from the generator terminals to the first over current device shall not

be less than 115 percent of the nameplate rating of the generator.

Remarque A:

Powermate Corporation

ne fournit pas de moteurs dans ses pièces détachées. Les moteurs sont couverts par la garantie du fabricant de moteurs. Consulter le

manuel du moteur inclus ou contacter notre département de service après-vente pour toute assistance.

Remarque B:

Ces pièces sont des pièces standard disponibles en quincaillerie.

Remarque C:

Pour commander un réservoir de rechange, contacter Centre de service

Powermate Corporation

le plus proche.

AVERTISSEMENT: Pour éviter toute blessure personnelle ou dommage à l’équipement, l’installation et tout entretien devralent être effectués par un

électricien qualifié ou un préposé au service autorisé. En aucun cas, une personne non-qualifiée ne devrait essayer de faire le raccord au circuit principal.

Électricité: Pour les modèles a approuvé pour la ville de Los Angeles: La charge limite en ampères des fils de phase allant des bornes du groupe électrogène au

premier appareil en surcharge ne doit pas être inférieure à 115% de la puissance nominale indiquée sur la plaque des caractéristiques du groupe électrogène.

Nota A:

Powermate Corporation

no proporcionará los motores como repuestos. Los motores están cubiertos por medio de la garantía del fabricante del motor. Consulte el

manual adjunto del motor o comuníquese con nuestro departamento de servicio para recibir ayuda al respecto.

Nota B:

Estas son piezas estándar disponibles en su ferretería local.

Nota C:

Para hacer pedidos de tanques, localice el Centro de Servicio de

Powermate Corporation

más cercano.

ADVERTENCIA: Para evitar posibles lesiones físcas o daños materiales, es necesario que la instalación y todo el servicio sea realizado por un electricista

matriculado o representatnte de servicio autorizado. Bajo ninguna circunstancia debe permitirse que una persona que no está capacitad trate de

manipular cables dentro del circuito de servicio eléctrico.

Eléctricos:

El amperaje de los conductores de fase desde los terminales del generador al primer dispositivo de sobrecorriente no podrâ ser menor que 115 porciento del valor