Por favor lea este instructivo antes de usar el producto
Please Read and Save this Use and Care Book
Plancha
Iron
Accesorios/Partes (EE.UU/Canadá)
Accessories/Parts (USA/Canada)
1-800-738-0245
USA/Canada 1-800-231-9786
Mexico 01-800-714-2503
www.blackanddecker.com
Modelo
Model
❑
AS800
Power Pro
™
Registre su producto en la Internet en el sitio Web www.prodprotect.com/applica
y tendrá la oportunidad de GANAR $100,000!
Register your product online at www.prodprotect.com/applica,
for a chance to WIN $100,000!
AS800Pub1000003154R1 11/15/06 8:56 AM Page 1
Page is loading ...
Page is loading ...
Page is loading ...
8
7
When using your iron, basic safety precautions should always be followed,
including the following:
❑
READ ALL INSTRUCTIONS BEFORE USING.
❑
Use iron only for its intended use.
❑
To protect against a risk of electric shock, do not immerse the iron
in water or other liquids.
❑
The iron should always be turned to “Off” before plugging or unplugging
from outlet. Never yank cord to disconnect from outlet; instead grasp plug
and pull to disconnect.
❑
Do not allow cord to touch hot surfaces. Let iron cool completely before
putting away. Loop cord loosely around the iron when storing.
❑
Always disconnect iron from electrical outlet when filling with water
or emptying and when not in use.
❑
Do not operate iron with a damaged cord or if the iron has been dropped
or damaged. To avoid the risk of electric shock, do not disassemble the
iron, take it to a qualified serviceman for examination and repair.
Incorrect reassembly can cause a risk of electric shock when the iron
is used.
❑
Close supervision is necessary for any appliance being used by or near
children. Do not leave iron unattended while connected or on an ironing
board.
❑
Burns can occur from touching hot metal parts, hot water, or steam.
Use caution when you turn a steam iron upside down- there may be hot
water in the reservoir.
SPECIAL INSTRUCTIONS
❑
To avoid a circuit overload, do not operate another high-wattage
appliance on the same circuit.
❑
If an extension cord is absolutely necessary, a 10-ampere cord should be
used. Cords rated for less amperage may overheat. Care should be taken
to arrange the cord so that it cannot be pulled or tripped over.
IMPORTANT SAFETY
INSTRUCTIONS
SAVE THESE INSTRUCTIONS.
Almacenamiento de la plancha
1. Desconecte la plancha y espere que se enfríe.
2. Almacene la plancha verticalmente sobre el talón de descanso,
a fin de evitar el goteo a través de la suela. Uno puede enrollar
el cable en torno al descanso de la plancha (N).
N
AS800Pub1000003154R1 11/15/06 8:56 AM Page 8
10
9
Soft-Touch Parts
Note: The soft-touch parts of this unit are free of natural rubber and latex.
They are safe for individuals allergic or sensitive to these materials.
POLARIZED PLUG
This appliance has a polarized plug (one blade is wider than the other). To
reduce the risk of electric shock, this plug will fit into a polarized outlet only
one way. If the plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician. Do not attempt to modify the plug
in any way.
TAMPER-RESISTANT SCREW
Warning: This appliance is equipped with a tamper-resistant screw to prevent
removal of the outer cover. To reduce the risk of fire or electric shock, do not
attempt to remove the outer cover. There are no user-serviceable parts
inside. Repair should be done only
by authorized service personnel.
Note: If the power supply cord is damaged, it should be replaced by
qualified personnel or in Latin America by an authorized service center.
Product may vary slightly from what is illustrated.
1. Spray nozzle
2. Water-fill cover
3. Digital display window
4. Surge-of-steam button
5. Spray button
6. Comfort Grip™ handle
7. 360-degree swivel cord
8. Smart stand/cord wrap
9. AUTO CLEAN
®
button
10. Water window with MAX mark
11. Fabric-select dial
12. Soleplate
M
A
X
A
U
T
O
C
L
E
A
N
Surge-of-Steam
Spray
Dry
Symbols
AS800Pub1000003154R1 11/15/06 8:56 AM Page 10
12
11
How to Use
This appliance is intended for household use only.
GETTING STARTED
Remove any labels, stickers or tags attached to the body or soleplate of the iron.
Note: Use ordinary tap water for ironing. Do not use water processed through a home
softening system
Important: For optimum performance, let the iron stand for 90 seconds before beginning
to iron.
Filling Water Tank
1. Open the water-fill cover as shown in (A).
2. Tilt the iron and using a clean measuring cup, pour water into
opening until the water reaches the MAX level mark on the water
tank (B). Do not overfill.
3. Close the water-fill cover.
Note: If you need to add water while ironing, unplug the iron and
follow above steps.
4. Plug in the iron. The iron beeps and digital display window
illuminates green.
Selecting Temperature
1. Read garment's label to help you determine fabric type.
Tip: If unsure of a garment's fiber, test a small area (on an inside seam or hem) before
ironing.
2. Once you determine the fabric type, turn fabric-select dial to
appropriate temperature setting (from 1 to 7).
Tip: As a guide, the digital display shows the setting number with
the corresponding recommended fabric type.
3. Once the iron reaches the selected temperature, it beeps and
displays READY (C).
3-Way Automatic Shutoff
The automatic shutoff feature in your iron works as follows:
• Once the iron reaches appropriate temperature, it will turn off
after 30 seconds of inactivity if left on its soleplate or tipped over
on its side. If left vertically on its heel rest, it will shut off after 8
minutes (D).
• The unit beeps three times and AUTO OFF flashes on the digital
display window to let you know the iron has stopped heating (E).
• After a few minutes, the digital display light goes off.
• If you pick up the iron, it activates an internal motion sensitive
detector and the iron will start heating again. You might have to
move the iron or shake it gently. The digital display light comes
on and the set temperature is displayed again.
A
B
C
E
D
8 minutes
30 seconds
Note: Wait for iron to reheat completely before resuming operation.
Smart Steam
™
Technology
The Smart Steam
™
system generates steam only at higher
temperature settings (between 4 and 7) (F). Once you select
the temperature, the Smart Steam
™
technology detects the set
temperature and adjusts the steam power accordingly. The higher
the setting, the more powerful the steam.
Surge of Steam
• Horizontal
Use to remove stubborn creases.
1. With the water tank filled to the MAX mark, set fabric-select dial to appropriate setting
(between 4 and 7) for your fabric. Read garment's label to help you determine fabric
type.
Note: Steam is automatically turned off between settings 1 and 3.
2. Once you select the appropriate setting, wait for iron to beep
and display READY.
3. Press the surge-of-steam button to generate a burst of steam
(G). For best performance, leave an interval of 5 seconds
between bursts.
Important: Always stand the iron on its heel rest when powered on
but not in use.
• Vertical
Use for removing wrinkles from hanging clothes and drapes.
1. Be sure the water tank is filled to the MAX mark.
2. Hang the garment to be steamed on a clothes hanger. (Curtains or drapes can be
steamed once they are hung.)
3. Set the fabric-select dial to appropriate setting (between 4 and 7) for your fabric.
4. Wait for iron to beep and display READY.
5. Hold the iron close to, but not touching, the fabric.
6. Pull the fabric tight in your free hand and pump the
surge-of-steam button as you move the iron over the
fabric (H).
Important: Always stand the iron on its heel rest when powered on
but not in use.
Using Spray
Use to dampen tough wrinkles at any setting (J).
1. Be sure the iron is filled with water.
2. On first use, pump the spray button several times.
ANTI-DRIP SYSTEM
The anti-drip system prevents water spotting at low temperatures.
Dry Ironing
1. Turn the fabric-select dial to setting 1, 2, or 3 to iron without
steam (K). The Smart Steam
™
system will automatically turn off
and there will not be any steam generated.
MAX
A
UT
O
C
L
EA
N
G
M
A
X
AU
T
O
C
L
E
A
N
H
M
A
X
A
UT
O
C
L
EA
N
J
F
K
AS800Pub1000003154R1 11/15/06 8:56 AM Page 12
14
13
2. To dry iron at higher settings, empty the water from the reservoir
to prevent steaming.
Emptying Water Tank (Optional)
Note: It is not necessary to empty the water after each use.
1. Unplug the iron and let it cool.
2. To release the water, hold the iron over a sink with the tip
pointing down. Water will empty out of the water-fill hole (L).
Care and Cleaning
This product contains no user-serviceable parts. Refer service to qualified service personnel.
Cleaning Outside Surfaces
1. Make sure iron is unplugged and has cooled completely. Wipe the soleplate and outer
surfaces with a soft cloth dampened with water. Add mild household detergent. Never
use abrasives, heavy-duty cleansers, vinegar or scouring pads that may scratch
or discolor the iron.
2. After cleaning, steam iron over an old cloth to remove any residue from the
steam vents.
Auto Cleaning
To keep the steam vents free of any buildup, about once a month follow these instructions.
1. Fill the water tank well below the MAX line. Plug in the iron.
2. Turn the fabric-select dial to 7 and stand the iron on its heel rest.
3. Wait for the iron to beep and READY to display on the digital window.
4. Unplug the iron and hold over a sink with the soleplate facing down.
5. Press and hold the AUTO CLEAN
®
button. Be careful, as hot water
and steam will come out of the steam vents (M). Continue to hold
the auto-clean button until all the water has emptied. If necessary,
rock iron side to side and front to back.
6. When finished, release the button, stand the iron on its heel rest
and plug it in. Heat for about 2 minutes to dry out any remaining
water.
Storing your Iron
1. Unplug the iron and allow it to cool.
2. Store vertically on its heel to prevent water leaking from the
soleplate. You can wrap the cord around the smart stand for
storage (N).
L
M
N
NOTES
AS800Pub1000003154R1 11/15/06 8:56 AM Page 14
NEED HELP?
For service, repair or any questions regarding your appliance, call the appropriate
"800" number on the cover of this book. Do not return the product to the place of
purchase. Do not mail the product back to the manufacturer nor bring it to a
service center. You may also want to consult the website listed on the cover of this
manual.
One-Year Limited Warranty
(Applies only in the United States and Canada)
What does it cover?
• Any defect in material or workmanship; provided; however, Applica’s liability will
not exceed the purchase price of the product.
For how long?
• One year after the date of original purchase.
What will we do to help you?
• Provide you with a reasonably similar replacement product that is either new or
factory refurbished.
How do you get service?
• Save your receipt as proof of the date of sale.
• Check our on-line service site at www.prodprotect.com/applica, or call our toll-
free number, 1-800-231-9786, for general warranty service.
• If you need parts or accessories, please call 1-800-738-0245.
What does your warranty not cover?
• Damage from commercial use
• Damage from misuse, abuse or neglect
• Products that have been modified in any way
• Products used or serviced outside the country of purchase
• Glass parts and other accessory items that are packed with the unit
• Shipping and handling costs associated with the replacement of the unit
• Consequential or incidental damages (Please note, however, that some states do
not allow the exclusion or limitation of consequential or incidental damages, so
this limitation may not apply to you.)
How does state law relate to this warranty?
• This warranty gives you specific legal rights, and you may also have other rights
that vary from state to state or province to province.
16
15
¿NECESITA AYUDA?
Para servicio, reparaciones o preguntas relacionadas al producto, por favor llame al
número del centro de servicio en el país donde usted compró su producto. NO
devuelva el producto al fabricante. Llame o lleve el producto a un centro de
servicio autorizado.
DOS AÑOS DE GARANTÍA LIMITADA
(No aplica en México, Estados Unidos o Canadá)
¿Qué cubre la garantía?
• La garantía cubre cualquier defecto de materiales o de mano de obra. Applica no
se responsabiliza por ningún costo que exceda
el valor de compra del producto.
¿Por cuánto tiempo es válida la garantía?
• Por dos años a partir de la fecha original de compra.
¿Cómo se puede obtener servicio?
• Conserve el recibo original de compra.
• Por favor llame al número del centro de servicio autorizado.
Esta garantía no cubre:
• Los productos que han sido utilizados en condiciones distintas a las normales
• Los daños ocasionados por el mal uso, el abuso o negligencia.
• Los productos que han sido alterados de alguna manera
• Los daños ocasionados por el uso comercial del producto
• Los productos utilizados o reparados fuera del país original de compra
• Las piezas de vidrio y demás accesorios empacados con el aparato
• Los gastos de tramitación y embarque asociados al reemplazo del producto
• Los daños y perjuicios indirectos o incidentales
AS800Pub1000003154R1 11/15/06 8:56 AM Page 16
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Black & Decker ICR505 User manual
-
Black & Decker F980 User manual
-
Black & Decker W100 User manual
-
Black & Decker Quick 'N Easy F905 User manual
-
-
-
Black and Decker D1700 Owner's manual
-
-
-
Other documents
-
BLACK+DECKER AS800 Owner's manual
-
Continental Electric CE23011 User manual
-
Continental Electric CE23011 User manual
-
Black and Decker Appliances F1075 User guide
-
Black and Decker Appliances D3300 User guide
-
Black and Decker Appliances IR03V User guide
-
-
Black and Decker Appliances ICR100 User guide
-
Weitech IR0322-0GPLA User guide
-
Black and Decker Appliances X800 Series User guide
