De Dietrich FC1045XS Owner's manual

Category
Ovens
Type
Owner's manual
FR GUIDE D'INSTALLATION
EN GUIDE TO INSTALLATION
DE EINBAUANLEITUNG
NL INSTALLATIEGIDS
PT MANUAL DE INSTALAÇÃO
CS PŘÍRUČKA K INSTALACI
Four
Oven
Backofen
Oven
Forno
Ovn
Trouba
2
3
TABLE OF CONTENTS
EN
1 / NOTICES TO THE USER
Safety instructions
_________________________________________
4
Caring for the Environment
__________________________________
5
2 / INSTALLING YOUR APPLIANCE
Choice of location
__________________________________________
6
Build-in
___________________________________________________
6
Electrical connection
_______________________________________
7
Changing the power cable
___________________________________
7
3 / DESCRIPTION OF YOUR APPLIANCE
Accessories
_______________________________________________
9
4 / CARING FOR AND CLEANING YOUR APPLIANCE
Cleaning the outer surfaces
__________________________________
12
Cleaning the door __________________________________________ 12
Self-degreasing catalytic
____________________________________
14
Changing the catalytic panels
Dismantling the wire supports
________________________________
14
What is pyrolysis?
__________________________________________
15
In what situations should pyrolysis be used?
____________________
15
5 / ADJUSTING YOUR APPLIANCE
Replacing the oven lamp
____________________________________
16
6 / TROUBLESHOOTING
__________________________________________
17
7 / AFTER-SALES SERVICE
________________________________________
18
4
1 / NOTICES TO THE USER
EN
SAFETY INSTRUCTIONS
This oven was designed for use by private
individuals in their homes. It is intended solely
for cooking foodstuffs. This oven does not
contain any asbestos-based components.
Please make sure children do not play with
the appliance.
When you receive the appliance, unpack it
or have it unpacked immediately. Give it an
overall inspection. Make note of any concerns
or reservations on the delivery slip and make
sure to keep a copy of this form.
Your appliance is intended for standard
household use. Do not use it for commercial
or industrial purposes or for any other
purpose than that for which it was designed.
Do not modify or attempt to modify any of
the characteristics of this appliance. This
would be dangerous to your safety.
WARNING: accessible parts may be hot
when in use. It is advisable to keep small
children away from the apppliance.
Never pull your appliance by the door
handle.
Before using your oven for the first time,
heat it while empty for approximately 15
minutes. Make sure that the room is
sufficiently ventilated. You may notice a
particular odour, or a small release of smoke.
All of this is normal.
WARNING: accessible parts may become
hot when the grill is used. It is advisable to
keep children away from the apppliance.
When in use, the appliance becomes hot.
Be careful not to touch the heating elements
located inside the oven.
When placing dishes inside or removing
them from the oven, do not place your hands
close to the upper heating elements and use
heat-protective kitchen gloves.
During pyrolysis, the exposed surfaces
become hotter than during normal use. It is
advisable to keep small children away from
the oven.
Before beginning a pyrolysis cleaning cycle
in your oven, remove all parts of your grids,
trays and accessories and remove major spill
residue. During pyrolysis, exposed surfaces
become hotter than during normal use. It is
advisable to keep small children away from
the oven.
At the end of cooking, do not pick up oven
or grill items (grid, rotisserie,...) with your bare
hands.
Never place aluminium foil directly in
contact with the floor of the oven (see the
chapter on oven description), as accumulated
heat may cause deterioration of the enamel.
Do not place heavy weights on the oven
door when open, and make sure that children
cannot climb or sit on it.
— The oven must be turned off when cleaning
inside the oven.
This appliance is not intended to be used by
persons (including children) with reduced
physical, sensory or mental abilities, or
persons lacking experience or awareness,
unless using it with the help of a person
reponsible for their safety, or under supervision
and with prior instruction in its use.
— In addition to the accessories supplied with
your oven, only use dishes capable of
withstanding high temperatures (follow the
manufacturer’s instructions).
— After using your oven, make sure that all the
controls are in their stop position.
— Do not use your oven as a larder or to store
any items after use.
— Never use steam or high-pressure devices to
clean the oven (electrical safety requirement).
Important
Keep this user guide with your
appliance. If the appliance is ever sold or
transferred to another person, ensure that
the new owner receives the user guide.
Please become familiar with these
recommendations before installing and
using your oven. They were written for your
safety and the safety of others.
5
1 / NOTICES TO THE USER
EN
CARING FOR THE ENVIRONMENT
This appliance’s packing materials are
recyclable. Recycle them and play a role in
protecting the environment by depositing
them in local authority containers provided
for this purpose.
Your appliance also contains many
recyclable materials. It is therefore marked
with this logo to indicate that used appliances
must not be mixed with other
waste. Recycling of the appliances
organised by your manufacturer will
thus be undertaken in optimum
conditions, in accordance with
European directive 2002/96/CE
relating to electrical and electronic
equipment waste. Contact your local council
or your retailer to find out the drop-off points
for used appliances that are nearest to your
home.
— We thank you for your help in protecting the
environment.
Warning
Installation should only be performed
by qualified installers and technicians.
This appliance complies with the following
European directives:
- Low Voltage Directive 2006/95/CE for
affixing the CE mark.
- Electromagnetic Compatibility Directive
89/336/CEE modified by directive
93/68/CEE for attaching the CE mark.
- CE regulation 1935/2004 concerning
materials and objects intended for contact
with food substances.
(
Depending on the model):
For your
safety, your oven is equipped with an
AUTOMATIC STOP, if you forget to turn off
your oven by mistake. After 23 hours and
30 minutes of continuous use, the AS
(Automatic Stop) feature will be activated and
your oven will turn itself off. AS or Auto Stop
will be displayed instead of the time and a
series of successive beeps will be emitted for
a short time.
6
2 / INSTALLING YOUR APPLIANCE
EN
BUILD-IN
To do this:
1) Remove the rubber screw covers to access
the mounting holes.
2) Drill a hole in the cabinet panel to avoid
splitting the wood.
3) Attach the oven with the 2 screws.
4) Replace the rubber screw covers (they also
absorb the shock caused by closing the oven
door).
(*) if the cabinet is open, its opening must be
70 mm (maximum).
CHOICE OF LOCATION
The above diagrams show the dimensions of a
cabinet that will be able to hold your oven.
The oven can be installed under a work top or
in a column of cabinetry (open* or closed)
having the appropriate dimensions for built-in
installation (see adjacent diagram).
Your oven has optimised air circulation that
allows it to achieve remarkable cooking and
cleaning results if the following guidelines are
followed:
Centre the oven in the cabinet so as to
guarantee a minimum distance of 5 mm
between the appliance and the cabinet beside it.
The material or coating of the cabinet must
be heat-resistant.
For greater stability, attach the oven in the
cabinet with two screws through the holes
provided for this purpose on either side of the
front inner panel (fig.1).
585
560
550
70
550
592
fig.1
Tip
To be certain that you have properly
installed your appliance, do not hesitate to
call on a household appliance specialist.
7
2 / INSTALLING YOUR APPLIANCE
EN
ELECTRICAL CONNECTION
Single-phase 20A Meter
220-240V
~
50Hz
Electrical outlet
2 poles
++ eeaarrtthh
standard CEI 60083
220-240 V
~
Single-phase line
Power
supply cable
length 1.50 m
approx.
16A fuse or differential
circuit breaker
The appliance must be fitted correctly to
guarantee electrical safety. During fitting and
maintenance operations, the appliance must
be unplugged from the electrical grid. Fuses
must be switched off or removed.
The electrical connections are made before
the appliance is installed in its housing.
Ensure that:
- the electrical installation has sufficient
voltage,
- the electrical wires are in good condition,
- the diameter of the wires complies with the
installation requirements.
Your oven must be connected with a
(standard) power cable with 3 conductors of
1.5mm
2
(1 live + 1 neutral + earth) which must
be connected to a 220-240V
~
single-phase
grid by means of a 1 live + 1 neutral + earth
CEI 60083 standard power socket or via an
all-poles cut-off device in compliance with the
installation rules.
Warning
The safety wire (green-yellow) is
connected to the appliance’s terminal
and must be connected to the earth terminal
of the electrical set-up.
You must enable the appliance to be
disconnected from the supply network after
installation.
Disconnection can be enabled by ensuring
that there is an accessible power plug or by
incorporating a switch into the fixed wiring in
compliance with the installation rules.
The fuse in your set-up must be 16 amperes.
If the power cable is damaged, it should be
replaced by the manufacturer, its after-sales
service department or a similarly qualified
person to avoid danger.
8
2 / INSTALLING YOUR APPLIANCE
EN
Warning
WWee ccaannnnoott bbee hheelldd rreessppoonnssiibbllee ffoorr aannyy aacccciiddeenntt rreessuullttiinngg ffrroomm aann iinneexxiisstteenntt,, ddeeffeeccttiivvee
oorr iinnccoorrrreecctt
ggrroouunndd lleeaadd..
IIff tthhee eelleeccttrriiccaall iinnssttaallllaattiioonn aatt yyoouurr rreessiiddeennccee rreeqquuiirreess aannyy cchhaannggeess iinn oorrddeerr ttoo hhooookk
uupp yyoouurr
AApppplliiaannccee,, ccaallll uuppoonn aa pprrooffeessssiioonnaall eelleeccttrriicciiaann..
IIff tthhee oovveenn mmaallffuunnccttiioonnss iinn aannyy wwaayy,, uunnpplluug
g tthhee aapppplliiaannccee oorr rreemmoovvee tthhee ffuussee ccoorrrreessppoonnddiinngg
ttoo tthhee sseeccttoorr tthheerree tthhee oovveenn iiss hhooookkeedd uupp..
9
3 / DESCRIPTION OF YOUR APPLIANCE
EN
Rear
Front
Anti-rocking safety grid (fig.1)
The grid can be used to hold all dishes and
moulds containing foodstuffs to be cooked or
browned.
It can be used for barbecues (to be placed
directly on the grid).
DESCRIPTION OF THE ACCESSORIES (depending on the model)
fig.1
fig.2
Multi-purpose dish (fig.2)
It serves as a cake dish and has a sloped
edge. It is used for cooking pastries such as
cream puffs, meringues, cup cakes, puff pas-
try, etc.
Inserted under the grid, it catches barbecue
juices and grease. It can also be used half-full
of water for double-boiler cooking methods.
Avoid placing roasts or meats directly in the
dish because this is certain to cause signifi-
cant spattering on the oven walls.
fig.3
• 45 mm multi-purpose tray. Fully
accessible sliding rail system (fig.3)
The new sliding rail system with support (fully
accessible) makes food more practical and
easier to handle as the trays can be effort-
lessly pulled for simpler handling. The trays
can be completely removed, providing full
access. Their stability ensures that food can
be handled safely, reducing the risk of burns.
This means that you can take food out of the
oven far more easily. Please note: the tray and
its support will remain hot. For more effective
use, place the tray and its support on the
rails, between the stops.
Do not directly place meat or poultry on the
drip tray for roasting. This would inevitably
produce splashes and dirty the sides of the
oven.
10
EN
3 / DESCRIPTION OF YOUR APPLIANCE
fig.5
fig.6
fig.4
fig.7
Multi-purpose 45 mm dish (fig.5)
When inserted in the supports under the grid,
it collects juice and fat from grilling, and can
be used half-filled with water as a double-
boiler.
Avoid placing roasts or meat directly in the
dish because this is certain to cause
significant spattering on the oven walls.
Sloped 45 mm dish equipped with
a special grid for grilling (fig.6)
It serves to collect juices and fat from
cooking meat or fish placed directly on the
grid during a grill or pulsed grill sequence.
Never place this dish on the floor of the oven
(it may damage the enamel) unless it is in the
grill position (the bottom heating element
does not turn on when the oven is set for
grilling).
Dish extracting support (fig.7)
Thanks to this system, you can slide out your
enamelled dish all the way and easily access
your preparations during cooking.
RReemmoovvee ffrroomm tthhee oovveenn bbeeffoorree ssttaarrttiinngg
ppyyrroollyyttiicc cclleeaanniinngg..
Multi-purpose 20 mm dish (fig.4)
When inserted in the supports under the grid,
it collects juice and fat from grilling, and can
be used half-filled with water as a double-
boiler.
Avoid placing roasts or meat directly in the
dish because this is certain to cause
significant spattering on the oven walls.
EN
3 / DESCRIPTION OF YOUR APPLIANCE
AACCCCEESSSSOORRIIEESS
((
depending on
the model)
ffiigg..22
Turn spit
In order to use it:
ppllaaccee tthhee hhoollllooww ddiisshh oonn tthhee ggrriidd oonn sshheellff
ssuuppppoorrtt nnuummbbeerr
1
ttoo ccaattcchh tthhee ccooookkiinngg
jjuuiicceess oorr iinn tthhe
e bboottttoomm ooff tthhee oovveenn iiff tthhee
iitteemm bbeeiinngg rrooaasstteedd iiss ttoooo bbiigg..
• slide one of the forks onto the spit; skewer
the piece of meat to be roasted; slide on the
second fork; centre and tighten by screwing
on the two forks using the handle (fig.1).
• place the spit in its cradle (fig.2).
• gently push to lodge the tip of the spit in
the guide slot located at the back of the oven
(fig.3).
• remove the handle by unscrewing, in order
to be able to close the door (fig.4). After
cooking, screw on the spit handle once again
in order to remove the roast without burning
yourself.
ffiigg..11
A
ffiigg..33
11
12
EN
4 / CARING FOR AND CLEANING YOUR APPLIANCE
CLEANING THE OUTER SURFACES (depending on the model)
To clean both the electronic programmer window and the oven door, use a window washing
product applied to a soft cloth.
Do not use abrasive creams or scouring sponges.
- Open the door completely and block it open
using the two red stops (fig.1).
They are supplied with your machine in the
plastic pack.
CLEANING THE DOOR (depending on the model)
fig.2
- Remove the first attached window as follows:
Insert the two red stops in the
AA
slots
designed for this (fig.2).
Lever these parts to release the glass (fig.3).
- Clean the glass using a soft sponge and
washing-up liquid.
Do not immerse the glass in water.
Do not use abrasive creams or scouring
sponges. Rinse with clean water and dry off
with a lint-free cloth.
AA
AA
Warning
Before removing the glass, allow the
appliance to cool down.
fig.1
CLIC
CLIC
fig.3
Disassembling the door
Warning
Do not use abrasive cleaning
products or hard metallic scrapers for
cleaning the oven’s glass door, as they
could scuff the surface and cause the glass
to shatter.
EN
13
4 / CARING FOR AND CLEANING YOUR APPLIANCE
- If necessary, remove the door’s inner glass
assembly. This assembly is composed of one
or two sheets of glass (depending on model),
each of which has a black rubber corner pad
(fig.4).
- After cleaning, reposition the four rubber
pads, taking care to follow the indications on
the glass:
* top left: L
* top right: R
Place your inner glass assembly in the door
so that L and R are located on the hinge side.
- If your oven is equipped with a single inner
sheet of glass, it must be located as close as
possible to the clipped glass.
- Clip in your last glass sheet by placing the
indication “PYROLYSIS” so that it faces you
(fig.5).
- Remove the red plastic stops.
Your appliance is again operational.
fig.4
CLAC
CLAC
fig.5
LL
RR
Warning
Do not use abrasive cleaning
products or hard metallic scrapers for
cleaning the oven’s glass door, as they
could scuff the surface and cause the glass
to shatter.
14
EN
4 / CARING FOR AND CLEANING YOUR APPLIANCE
SELF-DEGREASING CATALYTIC (enamelled oven)
(depending on the model)
- This oven is composed of an enclosure fitted with detachable walls covered with a special
microporous enamel (catalytic enamel), which provides its self-degreasing properties. As soon
as dirt appears, it spreads out and is dispersed into the microporous holes. It is oxidised on
both sides and gradually disappears. The self-degreasing enamel is mainly suited for fatty, rather
than sugary substances. This is why the oven floor, which is more subject to sugary overflow, is
not covered with this enamel.
WWee ssttrroonnggllyy rreeccoommmmeenndd::
- That you do not scrub these catalytic walls with metallic brushes, pointed or sharp instruments.
- That you do not try to clean them with commercial scouring products.
- When grilling food, the temperature of the walls is not always sufficient to eliminate major
spattering of fat.
In this case, following cooking, prolong the heating of the oven for 20 to 30 minutes, at the
maximum temperature of the chosen sequence.
If traces of spatter remain, they will be reduced during subsequent cooking operations.
BBeeffoorree ssttaarrttiinngg ttoo ddiissaasssseemmbbllee tthhee aapppplliiaannccee,,
lleett iitt ccooooll ddoowwnn aanndd eennssuurree tthhaatt iitt hhaass bbeeeenn
ddiissccoonnnneec
ctteedd ffrroomm tthhee ppoowweerr ssuuppppllyy..
CHANGING THE CATALYTIC PANELS -
DISMANTLING THE WIRE SUPPORTS
(depending on the model)
-- SSiiddee ppaanneellss wwiitthh wwiirree ssuuppppoorrttss::
Unhook the wire shelf support
((BB ffiigg..22))
at the
front by lifiting it (
diagram
AA ffiigg..11
). Pull the shelf
support structure towards you, lifting it so as to
unhook the rear attachment (
diagram
BB ffiigg..11))
.
Remove it from the 2 holes
((CC ffiigg..22))
in the
catalytic panel and from the oven cavity. Then
remove the catalytic panel
((AA ffiigg..22))..
Replace the
new elements (shelf supports) by performing
these operations in reverse.
-- RReeppllaaccee tthhee bbaacckk ppaanneell
Completely unscrew the screw
((EE ffiigg..22))
located at the top of the back panel
((DD ffiigg..22))
.
Tilt the panel forwards in order to remove it
from the oven cavity. Fit the new panel by
repeating these steps in reverse.
fig.2
A
B
C
D
E
A
B
C
B
A
fig.1
Warning
- The oven must be turned off when
cleaning inside the cavity.
EN
15
4 / CARING FOR AND CLEANING YOUR APPLIANCE
If your oven emits smoke during preheating or releases large amounts of smoke during cooking.
If your oven releases an unpleasant odour when cooled after various types of cooking (lamb,
fish, grills, etc...).
- Pyrolysis is a cycle during which the oven cavity is heated to a very high temperature in order
to eliminate spatters and spills. Smoke and odours released during pyrolysis are destroyed by
moving through a catalyzer.
- Pyrolysis is not necessary after each cooking cycle, simply when the degree of soiling warrants it.
- As a safety measure, the cleaning operation only begins after the door has automatically
locked. As soon as the internal temperature of the oven exceeds cooking temperatures, it is
impossible to unlock the door even if the “function selector” is set to 0.
RReellaattiivveellyy cclleeaann
ccooookkiinngg ooppeerraattiioonnss
MMeessssyy
ccooookkiinngg ooppeerraattiioonnss
VVeerryy mmeessssyy
ccooookkiinngg ooppeerraattiioonnss
Biscuits, vegetables, pastry,
quiches, soufflés...
Meat, fish (in a dish), stuffed
vegetables.
Large cuts of meat on the spit.
Splatter-free cooking: pyrolysis is
not warranted.
Pyrolysis may be warranted after
every 3 cooking cycles.
Pyrolysis can be performed after
one cooking application of this
kind, as there is a lot of
splattering.
WHAT IS PYROLYSIS? (depending on the model)
Tip
You should not wait until the oven is overly coated in grease to initiate a cleaning cycle.
IN WHAT SITUATIONS SHOULD PYROLYSIS BE USED?
(depending on the model)
Tip
Your oven is equipped with enamelled wire shelf supports: these need to be removed
before running the pyrolysis cycle.
Warning
Remove any cookware, grids and trays from the oven and clean any major spill residue
before carrying out the pyrolysis.
16
EN
5 / ADJUSTING YOUR APPLIANCE
Tip
To unscrew the view port and the light,
use a rubber glove, which will make
disassembly easier.
Warning
Make sure the appliance is
disconnected from the power before
replacing the lamp in order to avoid the risk
of electric shock. Change the lamp only
when the appliance has cooled down.
REPLACING THE OVEN LAMP
Bulb
Unscrew
View port
fig.1
The lamp is accessible:
IInnssiiddee tthhee oovveenn..
The bulb is located on the ceiling of your
oven’s cavity.
- Unscrew the view port counter-clockwise
(fig.1),
- Pull out the bulb.
Bulb specifications:
- 15 W
- 220-240 V
~
- 300°C
- E 14 cap.
- Replace the bulb then replace the view port
and reconnect your oven.
EN
17
6 / TROUBLESHOOTING
Tip
In all circumstances, if your efforts are not sufficient, contact the After-Sales Service
Department without delay.
IIff yyoouu hhaavvee aa ddoouubbtt aabboouutt tthhee ccoorrrreecctt ffuunnccttiioonniinngg ooff yyoouurr oovveenn,,
this does not
necessarily mean that there is a malfunction.
IInn aannyy eevveenntt,, cchheecckk tthhee ffoolllloowwiinngg ppooiinnttss::
Warning
- Repairs to your appliance should only be performed by professionals. Non-standard
repairs may be a source of danger for the user.
**
OOnnllyy ffoorr mmooddeellss wwiitthh tthhee ppyyrroollyyssiiss ffuunnccttiioonn..
YYOOUU OOBBSSEERRVVEE
TTHHAATT
PPOOSSSSIIBBLLEE
CCAAUUSSEESS
WWHHAATT SSHHOOUULLDD YYOOUU DDOO??
TThhee oovveenn iiss nnoott hheeaattiinngg..
- The oven is not connected to
the power supply.
- Your fuse is not working.
- The selected temperature is
too low.
Plug in your oven.
Replace the fuse in your electrical
set-up and check its capacity (16A).
Increase the selected temperature.
**
TThhee ppaaddlloocckk iiss ffllaasshhiinngg..
- Problem with the door’s
locking mechanism.
Call the After-Sales Service
Department.
TThhee oovveenn lliigghhtt iiss nnoott
wwoorrkkiinngg..
- The light is not working.
- The oven is not connected or
the fuse is not working.
Change the bulb.
Plug in your oven or change the
fuse.
**
TThhee ppyyrroollyyssiiss cclleeaanniinngg
ccyyccllee ddooeess nnoott bbeeggiinn..
- The door is not properly
closed.
- The locking system is
defective.
Verify that the door is locked.
Call the After-Sales Service
Department.
YYoouurr oovveenn iiss bbeeeeppiinngg..
- During cooking.
- At the end of a cooking cycle.
The temperature recommended
for your choice has been reached.
Your programmed cooking cycle
is finished.
TThhee ccoooolliinngg ffaann ccoonnttiinnuueess
ttoo ooppeerraattee aafftteerr tthhee oovveenn
ssttooppss..
- The fan should work for up to
an hour after cooking, or
when the oven temperature is
greater than 125°C.
- If it does not stop after 1 hour.
Open the oven door to cool down
the oven faster.
Call the After-Sales Service
Department.
7 / AFTER-SALES SERVICE
Any repairs that are made to your appliance
must be handled by a qualified professional
authorised to work on the brand. When you
call, mention your appliance’s complete
reference (model, type, serial number). This
information appears on the manufacturer’s
nameplate
(fig.1).
GENUINE REPLACEMENT PARTS
During maintenance work, request that
only
certified genuine replacement parts are
used.
• SERVICE CALLS
BRANDT APPLIANCES SAS
7 rue Henri Becquerel
92500 RUEIL MALMAISON
230V ~ 50 Hz
MADE IN FRANCE
fig.1
FFaaggoorrBBrraannddtt SSAASS
, Management company – SAS: social capital of 20,000,000 euros RCS Nanterre 440 303 196.
CZ5700522-00 09-10
EN
18
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18

De Dietrich FC1045XS Owner's manual

Category
Ovens
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI