Ciro G0050148 User manual

Brand
Ciro
Model
G0050148
Type
User manual

Ciro G0050148 is a 3/4” Clamp Accessory Mount designed for easy and secure attachment of accessories to bars or tubes. Its versatile design allows for mounting in various locations, making it suitable for a wide range of applications.

The clamp mount features a 3/4" female clamp half that slides over the hook of the 3/4" male clamp half, ensuring a firm grip on the mounting surface. The included 1/4-20 x 3/4" screw and ball post provide flexibility for attaching accessories.

To ensure proper installation, follow the provided instructions carefully. Select a straight section of the bar or tube, clean the mounting surface, and position the clamp halves accordingly. Tighten the screw and ball post securely, but avoid overtightening.

Ciro G0050148 is a 3/4” Clamp Accessory Mount designed for easy and secure attachment of accessories to bars or tubes. Its versatile design allows for mounting in various locations, making it suitable for a wide range of applications.

The clamp mount features a 3/4" female clamp half that slides over the hook of the 3/4" male clamp half, ensuring a firm grip on the mounting surface. The included 1/4-20 x 3/4" screw and ball post provide flexibility for attaching accessories.

To ensure proper installation, follow the provided instructions carefully. Select a straight section of the bar or tube, clean the mounting surface, and position the clamp halves accordingly. Tighten the screw and ball post securely, but avoid overtightening.

G0050148, REV._ Page 1 of 1For the latest version of installation instructions visit www.ciro3d.com
This indication alerts you to the fact that ignoring the contents described herein can result in potential serious injury or death if not followed.
This indication alerts you to the fact that ignoring the contents described herein can or will result in material damage and/or personal injury.
This indication alerts you to the fact if you ignore this detail you will affect the performance or functionality of the product.
NOTE: Ciro products are designed and manufactured under very strict quality control. Ciro warrants that products sold to the original purchaser shall be free from any defects in materials
and workmanship for a period of 3 (three) years from the date of purchase, and a lifetime warranty against LED failure. Ciro will have no obligation if the customer cannot show proof of
purchase. Warranty will not be granted unless the part is properly installed and maintained. Ciro will not be liable for any consequential and incidental damages, including labor, or
non-Ciro products. Please visit Ciro3d.com for our complete warranty policy.
All Ciro products are designed for "easy assembly" and/or "plug and play". We recommend a competent mechanic install our products, using standard mechanical procedures to assure a
safe and successful installation. Read completely and understand the instructions prior to starting installation.
WARNING
CAUTION
ATTENTION
Female clamp half
Male clamp half
Installation Instructions:
Step 1 Park on a level surface, allow the vehicle to cool.
Note: Tightening this clamp onto a bar may mark the surface.
Step 2 Select location to install clamp, ensuring clearances to
all surrounding components, and that the section of
tubing is straight. Avoid mounting on bends.
Step 3 Clean the mounting surface with an amonia based
cleaner to remove debris and waxes.
Step 4 Position the male half of the clamp (Fig.1) onto the bar.
This half of the clamp will be on the opposite side of the
ball post.
Step 5 Slide the female half of the clamp (Fig.1) over the hook of
the male half of the clamp, aligning the screw holes of
the clamp halves.
Step 6 Insert the screw through the clamp halves, going
through the male half first.
Step 7 Thread the ball post onto the screw so that it is only finger tight.
Step 8 Fine tune the position of the clamp and ball post assembly, then fully tighten the screw and ball post.
Do not overtighten. Do not exceed 7-10 ft-lbs.
Note: There will be a small gap between the clamp halves when it is properly installed. Fig.2.
Note: If you have purchased a Ciro accessory to go with the Clamp Mount, please refer to the instructions included with that
product to complete installation.
3/4” Clamp Accessory Mount
Items Included: 3/4” Female Clamp Half
3/4” Male Clamp Half
Ball Post
1/4-20 x 3/4” Screw
Fig.1 Fig.2
  • Page 1 1

Ciro G0050148 User manual

Brand
Ciro
Model
G0050148
Type
User manual

Ciro G0050148 is a 3/4” Clamp Accessory Mount designed for easy and secure attachment of accessories to bars or tubes. Its versatile design allows for mounting in various locations, making it suitable for a wide range of applications.

The clamp mount features a 3/4" female clamp half that slides over the hook of the 3/4" male clamp half, ensuring a firm grip on the mounting surface. The included 1/4-20 x 3/4" screw and ball post provide flexibility for attaching accessories.

To ensure proper installation, follow the provided instructions carefully. Select a straight section of the bar or tube, clean the mounting surface, and position the clamp halves accordingly. Tighten the screw and ball post securely, but avoid overtightening.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents