PQL -55597 LED Spec Select Designer Strip Retrofit User manual

-55597 LED Spec Select Designer Strip Retrofit
Brand
PQL
Model
-55597 LED Spec Select Designer Strip Retrofit
Category
Floodlights
Type
User manual

This manual is also suitable for

LED SPEC-SELECT™ DESIGNER STRIP RETROFIT
INSTALL INSTRUCTIONS
PREMIUM QUALITY LIGHTING® • www.PQLighting.com
© P.Q.L., Inc. • 2285 Ward Avenue • Simi Valley, CA 93065 • 800-323-8107
Specifications subject to change without notice. Photos and line
drawings may not be to scale and are for general reference only.
PLEASE FIND A QUALIFIED ELECTRICIAN FOR INSTALLATION. Please read the instructions before you install and use the luminaire.
WARNING, CAUTIONS AND OPERATING INSTRUCTIONS
WARNING – Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt
installation. Contact a qualified electrician.
WARNING – Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs
and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
WARNING – Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for
enclosed wiring and components.
Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation. Do not leave any other open holes
in an enclosure of wiring or electrical components.
WARNING: RISK OF FIRE OR ELECTRICAL SHOCK
• Turn o electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
• Turn o the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• All wiring connections should be capped with UL approved wire connectors.
CAUTION: RISK OF INJURY
• Avoid looking directly at the light source for prolonged periods of time while it is on.
• Account for small parts and destroy packing material, as these may be hazardous to children.
• Risk of burn. Disconnect power and allow fixture to cool before changing bulb or handing fixture.
• Green ground screw provided in proper location. DO NOT RELOCATE.
• Minimum 90° supply conductors.
• Suitable for Dry or Damp locations.
THE KITS HAVE BEEN TESTED, FULLY AND PROPERLY MOUNTED IN A FIXTURE AS SIMILAR AS POSSIBLE TO THE KIT’S INTENDED USE. THE UNIVERSAL DESIGN
FITS MOST .” TO .” WIDE T/T FLUORESCENT STRIPS.
INSTALLATION STEPS:
1. Shut o power to existing fixture. Disconnect the black and the white power supply wire (and ground wire if equipped) to existing ballast.
2. Remove the original lamps from the existing fixture. (Recycle lamps according to state specific recycling guidelines.)
3. Remove ballast cover, ballast, socket-bars and wiring. (Fig. 1)
Continued on next page...
WARNING - TURN OFF POWER SUPPLY FROM MAIN CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING.
!
Fig. 1
KIT INCLUDES
Part Quantity
4FT 8FT
Retrofit Housing 1 2
Installation Bracket 2 3
Lens 1 2
Installation Instructions 1 1
Label 1 1
4.25” - 5.25”
1.625”
Housing
Remove ballast cover,
ballast socket bars and
wiring.
LED SPEC-SELECT™ DESIGNER STRIP RETROFIT
INSTALL INSTRUCTIONS
PREMIUM QUALITY LIGHTING® • www.PQLighting.com
© P.Q.L., Inc. • 2285 Ward Avenue • Simi Valley, CA 93065 • 800-323-8107
Specifications subject to change without notice. Photos and line
drawings may not be to scale and are for general reference only.
20W 25W 30W 5000K-3500K20W 25W 30W 5000K-3500K
FIELD ADJUSTABLE WATTAGE & CCT (Fig. 4)
The end user may adjust the color temperature and
lumen output, respectively, by the two slide switches
integrated into the side of the fixture. Each switch
has 3 options (left, middle and right ), each position
corresponds to 1 of 3 color temperatures (Warm White,
Cool White, and Sky-Brite®) and 1 of 3 wattages, which
can be adjusted to the desired combination.
Default Settings for 55594: 40W, 5000K
Default Settings for 55597: 75W, 5000K
1. Switches are located on the LED Module driver box.
2. Select a wattage and color temperature by sliding
switch left or right respectively to the desired value.
WARNING - TURN OFF POWER SUPPLY FROM MAIN CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING.
!
Slide Switches
Fig. 4
INSTALLATION STEPS (cont’d):
4. Install retrofit brackets using screws. (Fig. 2)
5. Make electrical connections per wiring diagram.
6. Install LED Retrofit Assembly.
7. Install lens - After installation check to make sure the lens is completely
secure, snapped inside the entire length of the lamp body and fitted under
the end cap. Gently pull down on the lens to ensure it does not shift.
8. Restore power to fixture. (Fig. 3)
GENERAL WIRING DIAGRAM
LED DRIVER
Black (Line)
White (Neutral)
Green (Ground)
TO SOURCE
120-277V
*Purple (Dim+)
*Grey (Dim-)
Blue (-)
Red (+)
Lead wires
to LED Load
* Dimming wires to
0-10V IEC
Compliant Control.
Cap individual leads
separately if unused.
Fig. 2
Safety Cable
Bracket
Fig. 3
Bracket
55594
CCT Switch
Wattage Switch
5000K - 3500K
22W 30W 40W
55597
CCT Switch
Wattage Switch
5000K - 3500K
45W 60W 75W
  • Page 1 1
  • Page 2 2

PQL -55597 LED Spec Select Designer Strip Retrofit User manual

-55597 LED Spec Select Designer Strip Retrofit
Brand
PQL
Model
-55597 LED Spec Select Designer Strip Retrofit
Category
Floodlights
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents