Dryflow DFLIF02 User manual

Brand: Dryflow

Model: DFLIF02

Type: User manual

Dryflow DFLIF02 is a high-speed, energy-efficient hand dryer that provides a quick and hygienic way to dry hands. With a drying time of 10-12 seconds, it's perfect for busy public restrooms. The dryer features a powerful 600W motor that generates a strong airflow of 130M3/H, ensuring efficient drying. It also boasts a compact design, making it suitable for small spaces. Additionally, the dryer is equipped with an adjustable sensor range of 5-15CM, allowing for customized use.

PLEASE READ CAREFULLY THROUGH THIS MANUAL BEFORE USING THE

PRODUCT, OBSERVING ALL SAFETY INFORMATION, WARNINGS.

V2 Jun.19

Slimforce Hand Dryer

User Manual

Dryflow, 7 Riverside Court, Don Road, Sheffield, S9 2TJ. UK.

+44 (0)114 3540047 | [email protected] | www.dryflow.co.uk

Before installing, be sure to read this installation manual and retain for future reference.

This product must be installed by qualified personnel in accordance with the instructions given in

this manual and installation must comply with all applicable regulations, national security

standards and laws in force in the country where the product is installed.

Turn off the power at the main switch before installing or servicing the dryer unit.

The dryer must not be installed on a flammable surface. Do not damage any parts of the electrical

connections.

Pre-arrange an appropriate power outlet and a system of disconnection in accordance with

current local regulations. Make sure the product is properly connected to ground. If there is no

ground connection, there is a risk of an electrical shock.

Do not install the dryer over a washbasin. If the power cord is damaged, it must be repaired by

qualified personnel to avoid any type of risk.

This dryer can be used by children aged 8 years and above. People with reduced physical, sensory

or mental abilities or lack of experience and knowledge, if they have been given supervision and

appropriate training regarding the use of the dryer in a safe manner, can use it with no restriction.

Children should not play with the apparatus. Cleaning and

maintenance performed by the owner should not be done without children having supervision.

During use, temperatures above 158℉ [70℃] may develop in the parts near the hot air nozzle. Do

not touch or cover the dryer during use or when finished using it.

General safety information:

WARNING

DANGER

WARNING

This product is intended

Failure to properly ground

Disconnect power at the

All units must be suppllied

for installation by a qualified service person.

Use AWG NO.12 solid conductor for wiring.

unit could result in service electrical shock

and/or death.

service breaker before installing or servicing.

with a 3-wire service. The ground wire must

be connected to the dryer’s backplate.

--NOTE: Do not install dryer over washbasin --

SAFETY WARNINGS

PACKING LIST

SPECIFICATION

Voltage:

220V-240V 50/60Hz,4A/1000W

Stand-by Power:

Less than 2.0W

Air Temperature:

40℃[104°F](Distance from nozzle=100MM[4"],Room Temp.=25℃[77°F])

Air Velocity:

100M/S[328 FT/S] / 360KM/H[224MPH]

Air Flow:

130M3/H[76.5CFM]

Drying Time:

10-12 Seconds

Timing Protection: Forced Hold-On 60 Seconds auto shut-off

Timing Duration:

Auto Shut-Off ≤3 Seconds after last sensor read

Sensor Range:

5-15CM[2"~ 5-7/8"], Owner Adjustable

Fuse Protection:

1kW,Main PCB, Φ5x20, 250V, 6A[230V]

Protection Level:

IP23

Electric Isolation:

CLASS ǀ (Metal cover)

Brush Motor:

30000RPM, 600W[0.8HP]

Noise [at 1M]:

74dB

Weight :

2.5KG[5.5lb]/Net Weight / 3.0KG[6.6lb]/Shipping Weight

ONLY to be used on same voltage as

product rated label marked.

ITEM

KEY ITEM QTY NOTES

ITEM DESCRIPTION

Hand Dryer Unit Complete

Owner Manual (OM - this booklet)

Mounting Template (MT)

Wall Anchors, Expansion

Self-threading Phillips PH Screws

Flat Washer

Hex Key (for cover screws)

Φ8x38MM [ 5/16" Dia.x 1-1/2"], for#10

Stainless Steel 304 Cover & Cabinet

M5x36MM [ No.10 AB x 1-3/16"]

F1 For M5[No.10 AB]Phillips PH Screws

For 4MM[ 5/32"] hex socket FH Screws

4MM [5/32"]

102MM

[4"]

174MM

[6-27/32"]

256MM[10-5/164"]

1200MM

[47-1/4"]

1000MM

[39-3/8"]

It is recommended to avoid installation

of dryer near high reflective objects

(mirror, stainless steel washbasins, etc.)

in order to avoid faulty function of the

presence sensor.

Recommended

L Min. = 300MM[11-13/16"]

Hand dryer is to be installed with hardwired

stub provided in advance of install by others.

See MT for complete reference to mounting

heights and power KO locations.

1kW: 220-240V/ 6A

BEFORE INSTALLATION

Installation must be carried out in accordance with the current edition of the local wiring regulations

code having jurisdiction. Installation should be performed only by a qualified electrician.

39MM

[1-17/32"]

27MM

[1-1/16"]

INSTALLATION

1. Be sure to turn off the electric supply before any operation.

2. Place template against wall at desired height (see mounting height recommendations)

and mark locations of 4 mounting holes Dia. 8mm(5/16").

3. Remove hand dryer back transportation only purpose screw.

4. Remove and retain 2 side security hex cover screws and cover.

5. Mount the hand dryer base on the wall.

6. If the hand dryer is supplied in hardwired:

a. Connect the live wire(Coloured Brown, Red, or Black) to the terminal block marked “L”.

b. Connect the neutral wire(Coloured Black, Blue) to the terminal block marked “N”.

c. Connect the ground wire(Coloured Green or Yellow) to the terminal block marked “E”.

7. Before replacing cover, there is a customized option to run the dryer heater on (1000W)

heater off(600W).The switch is clearly marked.

8. Default setting is 12-15CM from nozzle. If it needs and please adjust its range.

9. Replace cover. Do not over-tighten screws.

HOT

AIR

ON/OFF

(Customized) DETECTION DISTANCE SETTING

OPERATION

Basic use

No-touch operation.

There is a blue LED light to guide user to the air flow.

Shake excess water from hands.

Place hands under the outlet to start operation.

Rub hands lightly and rapidly.

Stops automatically after hands are removed.

WARRANTY

All of our dryers are designed and manufactured to provide years of dependable performance.

Component parts are guaranteed to be free of defects in material and workmanship for a

period of one (1) year from date of original invoice. This guarantee will be honored provided

that the dryer is installed and maintained in accordance with the instructions. Parts damaged

during the installation are the purchaser’s responsibility. The warranty covers defects exclusively,

and only liability for the replacement of defective parts will be accepted. This warranty does not

cover wear and tear, or misuse and abuse. Defective parts must be returned, accompanied by the

serial number, to the point of purchase.

This warranty is granted solely to the original purchaser of the unit and is subject to registration.

Periodic cleaning of the unit is recommended.

Remove cover and clean dryer dust lint.

Wipe the cover with a damp cloth and

mild cleaning solution.

Do not soak. Never use abrasives to clean the cover.

Ensure the breaker supplying the dryer is operational. If it is,

disconnect the power and remove the hand dryer cover.

Check all the wire connections to make sure they are well fixed.

Turn on power and if it does not work then replace circuit board.

Turn motor blower several times by hand to see if it is blocked.

Ensure that there is no obstruction on or in front of the infrared

sensor zone. Clean any dirt off the sensor lens.

Try adjusting the sensitivity potentiometer on program board. If

still not working, replace circuit board and sensor board.

Check the motor brush worn condition. Replace them or a new

motor.

Check if the heat element switch is power on.

Check if the heat element was broken. If yes, replace a new one.

Hand dryer fails to

start

Hand dryer turns

on/off erratically

or not sensitive

enough

Hand dryer makes

ticking noise

Not hot air

MAINTENANCE

DIAGNOSTICS & REMEDIES

Periodic cleaning of the unit is recommended. Remove cover and clean dryer dust lint.

Stainless steel is highly resistant to rust, but there are some very strict cleaning and maintenance rules to be

followed to prevent damage to its appearance.

Apply neutral detergents formulated for these purposes (non-ionic surfactants and citric acid). Apply

the detergent with soft cloth. Be careful with abrasive cloths. They may scratch the surface. Rinse with

water until all the detergent has gone.

Residue from hygiene products, liquid soap, shampoos, bath gel, etc, can also damage surfaces.

Rinse the surface with plenty of water after use.

Limescale stains can be prevented by drying the surface with a soft cloth after use.

Limescale from mains water: Apply a solution of one part vinegar and three parts water directly to the

stains and leave to work for a few minutes. Then rub with a soft cloth or damp sponge. Then give it a final

wash with plenty of water and neutral soap to ensure it is thoroughly rinsed.

Unacceptable practices (loss of guarantee)

- Do not apply detergents with abrasive products or which contain:

Hydrochloric acid

Sodium hypochlorite (bleach)

Formic acid.

- Do not use abrasive utensils like metal sourcing pads or abrasive sponges.

- Do not spray the detergent on the surface, because the liquid can get into the openings or cracks in

them and cause damage.

- Do not use anti-limescale and descaling cleaning products. They are not suitable for cleaning

stainless

steel.

- Do not use silver cleaners, contain chlorides that attack stainless steel.

Bleach and descalers are often applied to bathroom equipment and left to work for a time. This

leads to the release of gases that contain chloride, which together with the water in the surface

cause chlorides to run down the surface of the stainless steel. This rusts both internal and external

surfaces.

Program Board Assembly

Main Board Assembly

Main Fuse

Power

Motor

MotorHeating

Heating

Sensor Assembly

LED Light Assembly [ Selection ]

Motor

Blue

Black

These two connectors

are interchangeable

Brown

Black

Heat Element

HOT/COLD Switch

[ Selection ]

See owner

adjustments

DIAGRAM BY STANDARD CIRCUIT BOARD

Yellow

Terminal Block

Grounding

Power (Hardwired) : 220V-240V 50/60Hz

860MM

101MM[4"]

(No recessing needed)

[33-55/64"]

Surface-Mounted

ADA-Compliant

Dryflow DFLIF02 User manual

Dryflow DFLIF02 User manual

Dryflow DFLIF02 User manual

Related papers

Other documents