Page is loading ...
MILANOSLIM
TECHNICAL MANUAL
15
MILANOSLIM
MilanoSlim pag. 17
16
Technical
information
Versions The MILANOSLIM shower is available in the THERMOSTATIC version and consists of the following:
A) IN-WALL UNIT including:
- A steel BOX with inlet pipes for the connection of cold and hot water, the system for the waterfall head shower connection.
- A MIXER BODY with thermostatic cartridge and a DIVERTER BODY with 3-way DIVERTER cartridge.
- A lower BODY for the connection of the water plug for the handshower.
The built-in part must be prepared and connected when completing the bathroom sanitary xtures right before carrying out the facing. 1/2” inlets.
NOTE: The in-wall unit must be installed at framing stage.
MILANOSLIM TRIM including:
- UPPER SHOWER HEAD IN STAINLESS STEEL with antilime system (to connect to the built-in part after carrying out the facing).
- PANEL IN STAINLESS STEEL WITH FRONT JETS.
- WATER PLUG WITH HANDSHOWER AND FLEXIBLE.
- THERMOSTATIC MIXER HANDLE AND DIVERTER HANDLE.
MilanoSlim functioning:
The lower handle controls the thermostatic cartridge to regulate the requested temperature.
The upper handle opens/closes the water and diverts it to the following outlets:
- UPPER SHOWER HEAD
- FRONT JET
- HANDSHOWER
MILANOSLIM
Refer to the instructions manual for correct installation guidelines.
MILANOSLIM
Minimum hydraulic pressure:
Maximum hydraulic pressure:
Hot water max temperature:
29 PSI
72PSI
176°F
Weight: - H001/H091: 16.5 lbs + 24 lbs
Recommended installation conditions:
- Hydraulic pressure:
- Hot water temperature:
43 PSI
from 131°F to 149°F
Guidelines
for the set-up
3 1/8” MIN.
3 7/8” MAX.
3/8” MIN.
1 1/8” MAX.
3 1/8”
3 1/8”
2”
2 1/8”
Connecting
Waters
Wire Coating
Base materials:
- Stainless Steel AISI 316
38 Polished Stainless Steel
93 Brushed Stainless Steel
MILANOSLIM
MilanoSlim
17
Shower column
• 1/2'' Thermostatic mixer
• Three-way diverter with integrated volume control
• Rainfall showerhead
• Body spray
• FIT handshower
• Anti-limescale system
• 48'' Vinyl hose
• Solid stainless steel construction
3/8"-1 1/8"
21 1/4"
3 1/8"
3/8"
3 1/8"-3 7/8"
3/8"
2 3/8"
2 3/8"
59 5/8"
14 1/8"3"3 1/2"
2 3/8" 12 1/4"
25 5/8"
1/2"
14 1/8"
1/4"
4 1/4" 3 1/8"
59"
1/2"
1/2"
13 3/8"
24"
2"
3 1/8"
Connecting
Water
Wire Coating
3 1/8"
2 1/8"
26" ± 2”
3 1/8" min.
3 7/8" man.
3/8" min.
1 1/8" man.
13"1 3/4"
Art. H001U Trim
Polished Stainless steel 72 38 H001U
Brushed Stainless steel 72 93 H001U
Art. H091U Rough
72 00 H091U
TOTAL PRICE
Polished Stainless steel
Brushed Stainless steel
Fantini USA Inc.
A&D BUILDING - 150 East 58th Street, 8th oor - New York, NY 10155
Ph. 212 308 8833 - Fax 212 308 8820
www.fantiniusa.com - [email protected]
/
