Invacare 1106628 User manual

Brand: Invacare

Model: 1106628

Category: Strollers

Type: User manual

This manual is also suitable for

Owner's Operator And Maintenance Manual

DEALER: THIS MANUAL MUST BE GIVEN TO

THE USER OF THE WHEELCHAIR.

USER: BEFORE USING THIS WHEELCHAIR,

READ THIS MANUAL AND SAVE FOR FUTURE

REFERENCE.

Solara jr.



Solara jr. 2 Part No. 1106628

WARNING

SAVE THESE INSTRUCTIONS.

WARNING

DO NOT OPERATE THIS EQUIPMENT

WITHOUT FIRST

READING AND UNDERSTANDING THIS

MANUAL. IF YOU ARE UNABLE TO

UNDERSTAND THE WARNINGS, CAUTIONS,

AND INSTRUCTIONS, CONTACT A

HEALTHCARE PROFESSIONAL, DEALER OR A

QUALIFIED TECHNICIAN BEFORE

ATTEMPTING TO USE THIS EQUIPMENT -

OTHERWISE INJURY OR DAMAGE MAY

RESULT.

THE INITIAL SET UP OF THIS WHEELCHAIR

MUST BE PERFORMED BY A QUALIFIED

TECHNICIAN.

PROCEDURES OTHER THAN THOSE DESCRIBED

IN THIS MANUAL MUST BE PERFORMED BY A

QUALIFIED TECHNICIAN.

WARNING

Part No. 1106628 3 Solara jr.

CONTENTS

TABLE OF CONTENTS

SPECIAL NOTES ............................................................................... 5

LABEL LOCATIONS .......................................................................... 6

SPECIFICATIONS ............................................................................. 7

PROCEDURE 1 - GENERAL GUIDELINES ........................................... 8

INFORMATION FOR HEALCHARE PROFESSIONALS/ASSISTANTS .................................8

STABILITY - ALL MODELS...................................................................................................................9

STABILITY - ALL MODELS EXCEPT RECLINERS .......................................................................9

STABILITY - RECLINER MODELS ONLY .................................................................................... 10

OPERATING INFORMATION........................................................................................................ 10

WEIGHT TRAINING ......................................................................................................................... 11

WEIGHT LIMITATION ..................................................................................................................... 11

SAFETY/HANDLING OF WHEELCHAIRS ................................................................................. 12

PROCEDURE 2 - SAFETY INSPECTION ............................................ 17

SAFETY INSPECTION CHECKLIST ............................................................................................. 17

TROUBLESHOOTING....................................................................................................................... 18

MAINTENANCE ................................................................................................................................. 18

PROCEDURE 3 - TRANSPORTING .................................................. 19

TRANSPORTING THE INVACARE SOLARA JR. ..................................................................... 19

PROCEDURE 4 - FRONT RIGGINGS ................................................. 20

INSTALLING/REMOVING SWINGAWAY FOOTREST ........................................................ 20

ADJUSTING SWINGAWAY FOOTREST HEIGHT................................................................. 21

ADJUSTING ADJUSTABLE ANGLE FLIP-UP FOOTPLATES ................................................ 22

COMPOSITE/ARTICULATING FOOTPLATE HEEL LOOP REPLACEMENT................. 23

INSTALLING/REMOVING ELEVATING LEGREST/CALFPAD ASSEMBLY ...................... 23

ADJUSTING THE ELEVATING LEGREST/CALFPAD ASSEMBLY ....................................... 24

PROCEDURE 5 - ARMS/POSITIONING STRAPS ................................ 25

USING/ADJUSTING DUAL POINT ARMS ................................................................................. 25

REPLACING DUAL POINT ARM PAD ........................................................................................ 26

REPLACING DUAL POINT ARM CLOTHING GUARDS ..................................................... 26

USING/INSTALLING/ADJUSTING CANTILEVER ARMS ...................................................... 27

ARM PAD REPLACEMENT FOR CANTILEVER ARMS .......................................................... 28

INSTALLING/REMOVING T-ARMS .............................................................................................. 29

ADJUSTING THE T-ARMS ............................................................................................................... 29

ADJUSTING T-ARM TRANSFER ASSISTS AND/OR SIDE GUARDS ................................ 31

INSTALLING/REPLACING SEAT POSITIONING STRAPS................................................... 32

INSTALLING/REPLACING CHEST POSITIONING STRAPS ............................................... 33

CONTENTS

Solara jr. 4 Part No. 1106628

CONTENTS

PROCEDURE 6 - BACK/SEAT .......................................................... 34

FOLDING/UNFOLDING BACK ASSEMBLY............................................................................... 34

INSTALLING/REMOVING STROLLER HANDLES ................................................................... 34

INSTALLING/REMOVING/ADJUSTING THE ADJUSTABLE ANGLE

STROLLER HANDLES................................................................................................................... 35

USING THE TELESCOPING BACK CANES.............................................................................. 37

INSTALLING/REPLACING THE BACK UPHOLSTERY ......................................................... 38

INSTALLING/REMOVING A SEATING SYSTEM ..................................................................... 39

REMOVING/INSTALLING THE SPREADER BAR..................................................................... 39

INSTALLING THE SEAT CUSHION............................................................................................. 40

PROCEDURE 7 - WHEELS/FORKS ..................................................... 41

REMOVING/INSTALLING REAR WHEELS ................................................................................ 41

ADJUSTING THE QUICK RELEASE AXLE ................................................................................ 42

SEAT TO FLOOR HEIGHT ADJUSTMENT ................................................................................ 42

ADJUSTING FORKS ........................................................................................................................... 43

PROCEDURE 8 - WHEEL LOCKS/ANTI-TIPPERS ............................... 44

ADJUSTING WHEEL LOCKS ......................................................................................................... 44

USING THE WHEEL LOCKS .......................................................................................................... 45

INSTALLING/ADJUSTING ANTI-TIPPERS ................................................................................. 46

PROCEDURE 9 - TILT/RECLINE ....................................................... 47

ENGAGING TILT-IN-SPACE/RECLINER OPERATION........................................................ 47

ADJUSTING TILT RELEASE CABLES............................................................................................ 50

POSITIONING TILT LOCKING COLLARS ................................................................................ 51

REPLACING BACK OR HEADREST UPHOLSTERY - RECLINER MODELS ONLY .... 52

ADJUSTING THE BACK HEIGHT - RECLINER MODELS ONLY ...................................... 53

PROCEDURE 10 - CONTRACTURE FOOTPLATE ............................... 54

CONTRACTURE ASSEMBLY ANGLE ADJUSTMENT ........................................................... 54

USING THE OPTIONAL QUICK RELEASE PIN ...................................................................... 55

ANGLE ADJUSTMENT OF THE CONTRACTURE FOOTPLATE ..................................... 55

CONTRACTURE FOOTPLATE DEPTH ADJUSTMENT....................................................... 55

CONTRACTURE FOOTPLATE HEIGHT ADJUSTMENT..................................................... 56

REPLACING THE CONTRACTURE FOOTPLATE HEEL LOOP ....................................... 56

WARRANTY .................................................................................. 59

CONTENTS

Part No. 1106628 5 Solara jr.

SPECIAL NOTES

WARNING/CAUTION notices as used in this manual apply to hazards or unsafe

practices which could result in personal injury or property damage.

NOTICE

THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO

CHANGE WITHOUT NOTICE.

As a manufacturer of wheelchairs, Invacare endeavors to supply a wide variety of

wheelchairs to meet many needs of the end user. However, final selection of the type

of wheelchair to be used by an individual rests solely with the user and his/her

healthcare professional capable of making such a selection.

WHEELCHAIR TIE-DOWN RESTRAINTS AND SEAT POSITIONING STRAPS

Invacare recommends that wheelchair users NOT be transported in vehicles of any

kind while in wheelchairs. As of this date, the Department of Transportation has not

approved any tie-down systems for transportation of a user while in a wheelchair, in a

moving vehicle of any type.

It is Invacares position that users of wheelchairs should be transferred into appropri-

ate seating in vehicles for transportation and use be made of the restraints made

available by the auto industry. Invacare cannot and does not recommend any wheel-

chair transportation systems.

AS REGARDS RESTRAINTS - SEAT /CHEST POSITIONING STRAPS - IT IS THE

OBLIGATION OF THE DME DEALER, THERAPISTS AND OTHER

HEALTHCARE PROFESSIONALS TO DETERMINE IF A SEAT/CHEST POSI-

TIONING STRAP IS REQUIRED TO ENSURE THE SAFE OPERATION OF THIS

EQUIPMENT BY THE USER. SERIOUS INJURY CAN OCCUR IN THE EVENT OF

A FALL FROM A WHEELCHAIR.

SPECIAL NOTES

Solara jr. 6 Part No. 1106628

LABEL LOCATIONS

WARNING

DO NOT OPERATE WITHOUT

THE ANTI-TIP TUBES

INSTALLED.

REV. 5/98

P/N 60106X144

Detent balls should extend beyond the diameter of the axle

WARNING

bushing for a positive lock. Keep detent balls clean.

1085306

! WARNING

Refer to Owner’s Manual BEFORE

adjusting axle mounting plate.

Refer to Owner's Manual

for proper anti-tipper

setting.

1085379

WARNING

Part No. 1106628 7 Solara jr.

SPECIFICATIONS

PHYSICAL DIMENSIONS

INVACARE SOLARA JR.

Overall Width: Seat Width + 8-1/4-inches (Example: 16-inch Wide Wheelchair =

24-1/4-inches Overall Width)

Overall Depth: 26-1/4-inches

(W/O Front Riggings)

Overall Height: * Seat-to-Floor Height + 20-inches (20-inch back canes)

* Seat-to-Floor Height + 24-inches (24-inch back canes)

Anti-Tippers: Standard

Footrest: Swing-Away Footrest - 90° (Standard) or 70°,

Elevating Legrests, Bilateral Contracture Footrests

Armrests: Dual Point Arms - Desk or Full Length, Adjustable or Fixed Height

Cantilever Arms - Bolt or Clamp-on, Desk or Full Length

T-Arms - Desk or Full Length, Adjustable Height

Seat Pan: Black Steel - Flush Mounted (Standard), Drop Mounted (Optional)

Back: Adjustable Height Swivel Canes - 20 to 24-inches or 24 to 28-inches

Fixed - 20 or 24-inches

Reclining - 20 or 24-inches

Back Angle Adjustment: 90° to 120° (10° increments)

Rear Axle: Quick-Release (Standard)

Rear Wheels: 12-inches Pneumatic (Standard)

12-inch Pneumatic w/flat free (Optional)

16, 18, 20, 22 and 24-inch Pneumatic, Urethane or Pneumatic w/flat

free (Optional)

Handrims: Aluminum Handrims (20, 22 and 24-inch)

Caster Size: 6 x 2-inch w/ Precision Sealed Bearings (Optional)

8-inch w/ Precision Sealed Bearings (Optional)

6 x 1-inch w/ Precision Sealed Bearings (Standard)

Seat Width: 10 to 16-inches

(Growable from 10 to 13-inches wide or from 13 to 16-inches wide)

Seat Depth: 12 to 18-inches

Back Cane Height: 20 and 24-inches

Wheel Locks: 12-inch Rear Wheels - Attendant Operated

16, 18, 20, 22, and 24-inch Rear Wheels - Pull to Lock

Tilt-In-Space: Dual Cable Trigger Mechanism (Standard) - 50° of Tilt

Recliner Back: Dual Cable Trigger Mechanism (Optional) 90 - 180° of Tilt

Frame: Aluminum

SPECIFICATIONS

* NOTE: The seat-to-floor heights are based on pneumatic tires and pneumatic tires with flat free

inserts. If wheelchair is equipped with urethane tires, subtract 1/4-inch from the measurements listed

above. All heights are measured with properly inflated new tires. These heights can vary +1/4-inch due

to tire wear.

SPECIFICATIONS

Solara jr. 8 Part No. 1106628

PROCEDURE 1 GENERAL GUIDELINES

GENERAL GUIDELINES

This Procedure Includes the Following:

Information For Healthcare Professionals/Assistants

Stability - All Models

Stability - All Models Except for Recliners

Stability - Recliner Option ONLY

Operating Information

Weight Training

Weight Limitation

Safety/Handling of Wheelchairs

INFORMATION FOR HEALTHCARE PROFESSIONALS/

ASSISTANTS

WARNING

The Solara jr. wheelchair MUST be operated by a healthcare professional or

assistant when in ANY tilt position.

ANTERIOR (FORWARD) TILT

DO NOT operate the wheelchair when the seat frame is in the anterior (for-

ward) tilt position (frame stops in the lower position and approximately 5°

forward tilt). Serious bodily injury may occur to the patient and/or the

assistant(s).

Anterior (forward) tilt is a feature of this wheelchair designed for the USE OF

A HEALTHCARE PROFESSIONAL or ASSISTANT ONLY. Engagement of

the anterior (forward) tilt must NEVER be performed by the wheelchair user.

When anterior (forward) tilt is needed, it must ALWAYS be engaged by a

HEALTHCARE PROFESSIONAL or ASSISTANT. Make sure the occupant of

the wheelchair is properly positioned and always engage both wheel locks.

Part No. 1106628 9 Solara jr.

STABILITY - ALL MODELS EXCEPT RECLINERS

WARNING

To maintain maximum stability, position the rear wheels in the most rearward posi-

tion in the axle mounting plate. Moving the rear wheels to any of the other mounting

positions causes the wheelchair to decrease in stability.

If moving the rear wheels to ANY forward position, ensure the wheelchair is stable

BEFORE using.

ALWAYS ensure stability BEFORE using maximum amount of tilt-in-space or moving

the rear wheels forward. TEST wheelchair BEFORE it is occupied by the end user to

ensure safety.

STABILITY - ALL MODELS

STABILITY WARNING

The back height, seat depth, back angle, seating system, tilt angle, seat height, size/

position of the rear wheels, size/position of the front casters, as well as the user

condition directly relate to the stability of the wheelchair. Any change to one (1) or

any combination of the eleven (11) may cause the wheelchair to decrease in stability.

These adjustments MUST be performed by a qualified technician.

ALWAYS make sure that the wheelchair is stable BEFORE using the tilt-in-space.

Back Height

Seat Depth

Back Angle

Seating System

Tilt Angle

Caster Size

Caster Position

Wheel Size

Wheel Position

User Condition

Wheel Locks

Anti-Tippers

Locking Collar

NOTE: When changes to the left hand column occur, follow across the chart and refer to the ü

procedure to maintain the proper stability, safety and handling of the wheelchair.

Back Height  üüüüüüüüN/A N/A N/A N/A

Seat Depth ü  üüN/A üüüüN/A N/A N/A ü

Back Angle üü  üüüüüüN/A N/A N/A ü

Seating System üüü  üüüüüüN/A N/A N/A

Tilt Angle N/A N/A ü N/A  N/A N/A N/A N/A N/A N/A N/A ü

Caster Size ü N/A ü N/A N/A  üüüN/A üüü

Caster Position ü N/A ü N/A N/A ü  üüN/A üüü

Wheel Size ü N/A ü N/A N/A üü  ü N/A üüü

Wheel Position ü N/A ü N/A N/A üüü  N/A üüü

User Condition üüüüüüüüü  N/A N/A N/A

Seat Height ü N/A üüüüüüüN/A üüü

PROCEDURE 1GENERAL GUIDELINES

GENERAL GUIDELINES

Solara jr. 10 Part No. 1106628

GENERAL GUIDELINES

PROCEDURE 1 GENERAL GUIDELINES

STABILITY - RECLINER MODELS ONLY

WARNING

Before using ANY recline position of this wheelchair, make sure the rear wheels are in

the MOST REARWARD position in the axle mounting plate to maintain the stability

of the wheelchair. DO NOT change the handling/maneuverability of the wheelchair

by moving the rear wheels to ANY of the forward positions. Moving the rear wheels to

ANY of the forward positions WILL change the center of gravity of the wheelchair,

making the wheelchair less stable.

ALWAYS make sure that the wheelchair is stable in the FULL RECLINED (back at 180°)

position AND the FULL UPRIGHT (back at 90°) position BEFORE using the recliner option.

BEFORE using the recliner option, make sure the anti-tipper wheel assemblies are in the

lowest adjustment hole (adjustment hole closest to the ground/floor).

ALWAYS engage both wheel locks while reclining or inclining (reverse recline) the

wheelchair.

Both gas cylinders MUST be operational and adjusted properly BEFORE using the

recliner. DO NOT operate the recliner option if only one (1) of the gas cylinders is

operational or adjusted properly.

Make sure the occupant of the wheelchair is properly positioned in the wheelchair BE-

FORE reclining or inclining (reverse recline) to maintain maximum stability and safety.

When returning the occupant of the wheelchair to the full upright position, more

body strength will be required for approximately the last twenty (20) degrees of

incline (reverse recline). Make sure to use proper body mechanics (use your legs) or

seek assistance to avoid injury.

ALWAYS return the back to the upright position before lifting the wheelchair.

OPERATING INFORMATION

GENERAL WARNINGS

Unless otherwise noted, all service and adjustments should be performed while the

wheelchair is unoccupied.

To determine and establish your particular safety limits, practice bending, reaching

and transferring activities in the presence of a qualified healthcare professional BE-

FORE attempting active use of the wheelchair.

ALWAYS wear your seat/chest positioning strap. Inasmuch as the SEAT/CHEST

POSITIONING STRAP is an option on this wheelchair (You may order with or

without the Seat/Chest Positioning Strap), Invacare strongly recommends ordering

the Seat/Chest Positioning Strap as an additional safeguard for the wheelchair user.

ALWAYS check foam grips for looseness BEFORE using the wheelchair. If loose,

contact a qualified technician for instructions.

The necessary back angle (90°, 100°, 110° or 120°) MUST be selected BEFORE reposi-

tioning the rear wheels forward.

DO NOT operate the tilt-in-space if the trigger release levers and cables are not properly

adjusted to ensure that the tilt-in-space is locked in place when engaged.

DO NOT TRAVERSE, CLIMB or GO DOWN ramps or slopes GREATER than 9°.

NEVER leave the occupied wheelchair unattended at any time, especially on an incline.

Part No. 1106628 11 Solara jr.

GENERAL WARNINGS (CONTINUED)

DO NOT attempt to reach objects if you have to move forward in the seat.

DO NOT attempt to reach objects if you have to pick them up from the floor by

reaching down between your knees.

DO NOT lean over the top of the back upholstery/seating system. This will change

your center of gravity and may cause you to tip over.

DO NOT shift your weight or sitting position toward direction you are reaching as

wheelchair may tip over.

WHEEL LOCKS ARE NOT BRAKES. DO NOT attempt to stop a moving wheel-

chair with the wheel locks.

DO NOT tip the wheelchair onto the rear wheels without assistance.

DO NOT use an escalator to move a wheelchair between floors. Serious bodily injury

may occur.

Before attempting to transfer in or out of the wheelchair, every precaution should be

taken to reduce the gap distance. Turn both casters parallel to the object you are

transferring onto. When transferring to and from the wheelchair, ALWAYS EN-

GAGE BOTH WHEEL LOCKS.

DO NOT use wheelchair unless it has the proper tire pressure (p.s.i.). DO NOT overin-

flate the tires. Failure to follow these suggestions may cause the tire to explode and cause

bodily harm. Recommended tire pressure is listed on the side wall of the tire.

DO NOT use ANY parts, accessories, or adapters other than those authorized by

Invacare. Otherwise, the warranty is void.

DO NOT attempt to lift a wheelchair by lifting on any removable (detachable) parts.

Lifting by means of any removable (detachable) parts of a wheelchair may result in

injury to the user or damage to the wheelchair.

DO NOT use the spreader bar for lifting or transporting the wheelchair. DO NOT use

the spreader bar as a weight bearing support.

DO NOT stand on the frame of the wheelchair.

Anti-tippers MUST BE attached at all times.

DO NOT use the footplates as a platform. When getting in or out of the wheelchair,

make sure that the footplates are in the upward position.

WEIGHT TRAINING

WARNING

Invacare DOES NOT recommend the use of its wheelchairs as a weight training

apparatus. Invacare wheelchairs have NOT been designed or tested as a seat for any

kind of weight training. If occupant uses said wheelchair as a weight training apparatus,

Invacare shall NOT be liable for bodily injury and the warranty is void.

WEIGHT LIMITATION

WARNING

The Invacare Solara jr. wheelchair has a weight limitation of 150 lbs. (68 kg.).

PROCEDURE 1GENERAL GUIDELINES

GENERAL GUIDELINES

Solara jr. 12 Part No. 1106628

PROCEDURE 1 GENERAL GUIDELINES

GENERAL GUIDELINES

SAFETY/HANDLING OF WHEELCHAIRS

Safety and Handling of the wheelchair requires the close attention of the wheelchair user as

well as the assistant. This manual points out the most common procedures and techniques

involved in the safe operation and maintenance of the wheelchair. It is important to practice

and master these safe techniques until you are comfortable in maneuvering around the

frequently encountered architectural barriers.

Use this information only as a basic guide. The techniques that are discussed on the follow-

ing pages have been used successfully by many.

Individual wheelchair users often develop skills to deal with daily living activities that may

differ from those described in this manual. Invacare recognizes and encourages each indi-

vidual to try what works best for him/her in overcoming architectural obstacles that they

may encounter, however ALL WARNINGS and CAUTIONS given in this manual MUST be

followed. Techniques in this manual are a starting point for the new wheelchair user and

assistant with safety as the most important consideration for all.

STABILITY AND BALANCE

WARNING

ALWAYS wear your seat/chest positioning strap. Inasmuch as the SEAT/

CHEST POSITIONING STRAP is an option on this wheelchair (You may

order with or without the Seat/Chest Positioning Strap), Invacare strongly

recommends ordering the Seat/Chest Positioning Strap as an additional

safeguard for the wheelchair user.

Anti-tippers MUST be attached at all times.

To assure stability and proper operation of your wheelchair, you must at all times maintain

proper balance. Your wheelchair has been designed to remain upright and stable during

normal daily activities as long as you do not move beyond the center of gravity.

Virtually all activities which involve movement in the wheelchair have an effect on the center

of gravity. Invacare recommends using seat/chest positioning straps for additional safety while

involved in activities that shift your weight.

DO NOT lean forward out of the wheelchair any further than the length of the armrests.

Make sure the casters are pointing in the forward position whenever you lean forward. This

can be achieved by advancing the wheelchair and then reversing it in a straight line.

The Invacare Solara jr. wheelchair should be operated by an assistant when the wheelchair is

in any tilted position.

COPING WITH EVERYDAY OBSTACLES

Coping with the irritation of everyday obstacles can be alleviated somewhat by learning how to

manage your wheelchair. Keep in mind your center of gravity to maintain stability and balance.

A NOTE TO WHEELCHAIR ASSISTANTS

When assistance to the wheelchair user is required, remember to use good body mechanics.

Keep your back straight and bend your knees whenever tipping the wheelchair or traversing

curbs, or other impediments.

Part No. 1106628 13 Solara jr.

WARNING

DO NOT attempt to lift the wheelchair by any removable (detachable) parts.

Lifting by means of any removable (detachable) parts of a wheelchair may

result in injury to the user or damage to the wheelchair.

DO NOT use the spreader bar for lifting or transporting the wheelchair. DO

NOT use the spreader bar as a weight bearing support .

Also, be aware of detachable parts such as armrests or legrests. These must NEVER be used

to move the wheelchair or as lifting supports, as they may be inadvertently released, resulting

in possible injury to the user and/or assistant(s).

When learning a new assistance technique, have an experienced assistant help you before

attempting it alone.

PERCENTAGE OF WEIGHT DISTRIBUTION

WARNING

DO NOT attempt to reach objects if you

have to move forward in the seat or pick

them up from the floor by reaching down

between your knees.

The back height, seat depth, back angle,

seating system, tilt angle, seat height, size/

position of the rear wheels, size/position

of the front casters, as well as the user

condition directly relate to the stability of

the wheelchair. Any change to one (1)

or any combination of the eleven (11)

may cause the wheelchair to decrease in

stability. These adjustments MUST be

performed by a qualified technician.

Many activities require the wheelchair owner to reach, bend and transfer in and out of the

wheelchair. These movements will cause a change to the normal balance, the center of gravity, and

the weight distribution of the wheelchair. To determine and establish your particular safety limits,

practice bending, reaching and transferring activities in several combinations in the presence of a

qualified healthcare professional BEFORE attempting active use of the wheelchair.

Proper positioning is essential for your safety. When reaching, leaning, or bending forward, it is

important to use the front casters as a tool to maintain stability and balance.

CENTER OF

GRAVITY

UNOCCUPIED OCCUPIED

PROCEDURE 1

GENERAL GUIDELINES

Solara jr. 14 Part No. 1106628

PROCEDURE 1 GENERAL GUIDELINES

GENERAL GUIDELINES

Reaching, Leaning and Bending - Forward.

WARNING

DO NOT attempt to reach objects if

you have to move forward in the seat

or pick them up from the floor by

reaching down between your knees.

Position the front casters so that they are

extended as far forward as possible and

engage wheel locks.

Reaching, Leaning - Backwards.

WARNING

DO NOT lean over the top of the

back upholstery. This will change

your center of gravity and may cause

you to tip over.

Position wheelchair as close as possible to the

desired object. Point front casters forward to

create the longest possible wheelbase. Reach

back only as far as your arm will extend

without changing your sitting position.

TIPPING

WARNING

DO NOT tip the wheelchair without assistance.

When tipping the wheelchair, an assistant should grasp the back of the wheelchair on a non-

removable (non-detachable) part. Inform the wheelchair occupant before tipping the wheelchair

and remind him/her to lean back. Be sure the occupants feet and hands are clear of all wheels

and/or pinch points.

After mastering the techniques of tipping the wheelchair, use one (1) of the following meth-

ods to tackle curbs, short stairs, etc.

TIPPING - CURBS: METHOD 1 - WHEELCHAIR WITH STEP TUBES:

Place foot on the step tube and begin to tilt

the wheelchair toward you. Apply a continu-

ous downward motion until the balance point

is achieved and the front casters clear the

curb. At this point, the assistant will feel a

difference in the weight distribution.

WARNING

When lowering the front casters of the

wheelchair, DO NOT let the wheelchair

drop the last few inches to the ground.

This could result in injury to the occu-

pant and/or damage to the wheelchair.

METHOD 1 - WHEELCHAIR WITH

STEP TUBES

Step Tube

Part No. 1106628 15 Solara jr.

Roll the wheelchair forward and slowly lower the front of the wheelchair in one continuous

movement onto the sidewalk. Push the wheelchair forward until the rear wheels roll up and over

the curb.

TIPPING - CURBS: METHOD 2 - WHEELCHAIR WITHOUT STEP TUBE

This method requires two (2) assistants. The second assistant should be positioned at the front of

the wheelchair lifting upward on a non-remov-

able (non-detachable) part of the wheelchair

frame when lifting the wheelchair and stabilizing

the wheelchair when the wheelchair is being

lowered to the ground.

The first assistant should stand on the sidewalk

and turn the wheelchair so that the rear wheels

are against the curb. Turn the anti-tippers so the

anti-tip wheels are pointing up. The wheelchair

should be tilted back to the balance point and, in

one continuous upward movement, the rear

wheels should be pulled up and over the curb.

DO NOT return the front casters to the

ground until the wheelchair has been pulled

backward far enough for the front casters to clear the edge of the curb.

WARNING

When lowering the front casters of the wheelchair, DO NOT let the wheelchair

drop the last few inches to the ground. This could result in injury to the occupant

and/or damage to the wheelchair.

Roll the wheelchair backward and SLOWLY lower the wheelchair in one continuous movement.

STAIRWAYS

WARNING

ALWAYS wear your seat/chest positioning strap. Inasmuch as the SEAT/CHEST

POSITIONING STRAP is an option on this wheelchair (You may order with or

without the Seat/Chest Positioning Strap), Invacare strongly recommends ordering

the Seat/Chest Positioning Strap as an additional safeguard for the wheelchair user.

DO NOT attempt to lift a wheelchair by lifting on any removable (detachable)

parts. Lifting by means of any removable (detachable) parts of a wheelchair may

result in injury to the user or damage to the wheelchair.

DO NOT use the spreader bar for lifting or transporting the wheelchair. DO

NOT use the spreader bar as a weight bearing support .

Extreme caution is advised when it is necessary to move an occupied wheelchair

up or down the stairs. Invacare recommends that, if possible, the user be re-

moved from the wheelchair prior to moving. Invacare recommends using two (2)

assistants and making thorough preparations. Make sure to use ONLY secure,

non-detachable parts for hand-held supports.

RECLINER OPTION ONLY - ALWAYS return the back to the upright position

before lifting the wheelchair.

METHOD 2 - WHEELCHAIR

WITHOUT STEP TUBE

PROCEDURE 1

GENERAL GUIDELINES

Solara jr. 16 Part No. 1106628

Follow this procedure for moving the wheelchair between floors when an elevator is NOT

available:

1. If necessary, rotate the anti-tippers so the wheels are facing up.

2. After the wheelchair has been tilted back to the balance point, one assistant (in the rear) backs the

wheelchair up against the first step, while securely grasping a non-removable (non-detachable) part

of the wheelchair for leverage.

3. The second assistant, with a firm hold on a non-detachable part of the framework, lifts the wheel-

chair up and over the stair and steadies the wheelchair as the first assistant places one (1) foot on

the next stair and repeats STEP 1.

4. The wheelchair should not be lowered until the last stair has been negotiated and the wheelchair has

been rolled away from the stairway.

5. If necessary, rotate the anti-tippers so the wheels are facing down.

ESCALATORS? SORRY!

DO NOT use an escalator to move a wheelchair between floors. Serious bodily injury

may occur.

TRANSFERRING TO AND FROM OTHER SEATS

WARNING

BEFORE attempting to transfer in or out

of the wheelchair, every precaution

should be taken to reduce the gap dis-

tance. Turn both casters parallel to the

object you are transferring onto. Also be

certain the wheel locks are engaged to

help prevent the wheels from moving.

CAUTION

When transferring, position yourself as

far back as possible in the seat. This will

help prevent broken screws, damaged

upholstery and the possibility of the

wheelchair tipping forward.

NOTE: This activity may be performed independently provided you have adequate mobility and upper body strength.

Position the wheelchair as close as possible along side the seat to which you are transferring, with the

front casters pointing parallel to it. Remove or flip up the armrest. Engage wheel locks. Shift body weight

into seat with transfer.

During independent transfer, little or no seat platform will be beneath you. Use a transfer board if at all

possible.

PROCEDURE 1 GENERAL GUIDELINES

GENERAL GUIDELINES

Part No. 1106628 17 Solara jr.

SAFETY INSPECTION PROCEDURE 2

SAFETY INSPECTION CHECKLIST

NOTE: Every six (6) months take your wheelchair to a qualified technician for a thorough inspection and

servicing. Regular cleaning will reveal loose or worn parts and enhance the smooth operation of your

wheelchair. To operate properly and safely, your wheelchair must be cared for just like any other vehicle.

Routine maintenance will extend the life and efficiency of your wheelchair.

Initial adjustments should be made to suit personal body structure and preference. Thereafter

follow these maintenance procedures:

This Procedure Includes the Following:

Safety Inspection Checklist

Troubleshooting Maintenance

SAFETY INSPECTION

ITEM Initially Weekly Monthly Periodically

GENERAL

Wheelchair rolls straight

(no excessive drag or pull to one side). X X

CLOTHING GUARDS

Inspect for bent or protruding metal. X X

Ensure all fasteners are secure. X X

ARMS - PROCEDURE 5

Secure but easy to release. X X

ARMREST - PROCEDURE 5

Inspect for rips in upholstery. X X

Base sits flush against arm tube. X X

TRIGGER RELEASE LEVER AND CABLE

- PROCEDURE 9

Cables completely release and handles return

when released. X X

REAR WHEELS - PROCEDURE 7

Sealed bearings and axle nut tension correct. X X

No excessive side movement/binding when

lifted from ground and spun. X X

HANDRIMS

Inspect for signs of rough edges or peeling finish. X X

FRONT CASTERS/FORKS - PROCEDURE 7

Inspect axle for proper tension by spinning

caster; caster should come to a gradual stop. X X

Adjust bearing system if wheel wobbles

noticeably or binds to stop. X X

Inspect fork and stem for damaged,

loose or missing hardware. X

Inspect casters for cracks and wear X X

CAUTION: As with any vehicle, the wheels,

casters and tires should be checked periodically

for cracks and wear, and should be replaced.

TIRES - PROCEDURE 7

Inspect for flat spots and wear. X X

If pneumatic tires, check for proper inflation. X X

Inspect rear tires for cracks and wear X X

CAUTION: As with any vehicle, the wheels,

casters and tires should be checked periodically

for cracks and wear, and should be replaced.

WHEEL LOCKS - PROCEDURE 8

Wheel locks do not interfere with tires when rolling. X X

Wheel locks easy to engage. X X

Pivot points free of wear or looseness. X X

CLEANING

Clean and wax all parts. X

Clean upholstery and armrests. X

Inspect axles are free from dirt, lint, etc. X

Inspect tilt slides and roller bearings are free

from dirt, lint, etc. X

Solara jr. 18 Part No. 1106628

SAFETY INSPECTION

TROUBLESHOOTING

Chair Chair Sluggish Squeaks

Veers Veers Turn or Caster and Looseness

Right Left Performance Flutter Rattles in Chair SOLUTIONS

X X X Check tires for correct

and equal pressure.

X X X X Check for loose nuts and bolts.

X X X Check that both casters contact

the ground at the same time.

MAINTENANCE SAFETY PRECAUTIONS

WARNING

After ANY adjustments, repair or service and BEFORE use, make sure all attach-

ing hardware is tightened securely - otherwise injury or damage may result.

CAUTION

DO NOT over tighten hardware attaching to the frame. This could cause

damage to the frame tubing.

SUGGESTED MAINTENANCE PROCEDURES

1. Keep quick-release axles free of dirt and lint to ensure positive locking and proper opera-

tion. Refer to ADJUSTING THE QUICK-RELEASE AXLE in PROCEDURE 7 of this manual.

WARNING

DO NOT use WD-40

, 3-in-1 oil

, or other penetrating lubricants on quick-

release axles. Otherwise, binding and/or damage to the wheelchair may occur.

2. Clean quick-release axles once (1) a week with a Teflon

lubricant.

WARNING

DO NOT use the wheelchair unless it has the proper tire pressure (p.s.i.). DO

NOT overinflate the tires. Failure to follow these suggestions may cause the

tire to explode and cause bodily harm.

3. If tires are pneumatic, recommended tire pressures will be listed on the side wall of the tires.

4. Periodically adjust wheel locks in correlation to tire wear. Refer to

WHEEL LOCK AD-

JUSTMENT in PROCEDURE 8 of this manual.

5. Make sure that ALL bolts are tight before operating wheelchair.

CAUTION

As with any vehicle, the wheels, casters and tires should be checked periodically

for cracks and wear, and should be replaced.

6. The wheels and tires should be checked periodically for cracks and wear, and should be replaced.

7. Keep tilt slides and roller bearings free of dirt and lint to ensure proper operation of the

tilt mechanism.

MAINTENANCE

SAFETY INSPECTIONPROCEDURE 2

Part No. 1106628 19 Solara jr.

TRANSPORTING THE INVACARE SOLARA JR.

1. Remove the seating system. Refer to the seating system Owner's Manual for installation and removal

of the seating system.

2. Remove the footrests (PROCEDURE 4).

3. Remove the rear wheels (PROCEDURE 7).

4. Remove the armrests (PROCEDURE 5).

5. Remove the stroller handle (if applicable) (PROCEDURE 6).

6. Fold the back towards the front of the wheelchair (PROCEDURE 6).

7. Remove the anti-tippers (PROCEDURE 8).

TRANSPORTING PROCEDURE 3

This Procedure Includes the Following:

Transporting the Invacare Solara jr.

TRANSPORTING

Solara jr. 20 Part No. 1106628

PROCEDURE 4 FRONT RIGGINGS

FRONT FRIGGINGS

This Procedure Includes the Following:

Installing/Removing

Swingaway Footrest

Adjusting Swingaway Footrest Height

Adjusting Adjustable Angle Flip-up Footplates

Composite/Articulating Footplate Heel Loop Replacement

Installing/Removing Elevating Legrest/Calfpad Assembly

Adjusting the Elevating Legrest/Calfpad Assembly

WARNING

After ANY adjustments, repair or service and BEFORE use, make sure all attach-

ing hardware is tightened securely - otherwise injury or damage may occur.

INSTALLING/REMOVING SWINGAWAY FOOTREST

(FIGURE 1)

INSTALLING

1. Turn the footrest to the side (open

footplate is perpendicular to the wheel-

chair).

2. Insert the footrest assembly mounting pin

into the mounting tube of the wheelchair

frame.

3. Rotate the footrest towards the inside of

the wheelchair until it locks into place.

NOTE: The footplate will be on the inside of the

wheelchair when locked in place.

4. Repeat STEPS 1-3 for the other footrest

assembly.

5. If necessary, adjust the footrest height.

Refer to

ADJUSTING SWINGAWAY

FOOTREST HEIGHT in this procedure of

the manual.

REMOVING

1. Push the footrest release lever inward while rotating the footrest outward.

2. Lift the footrest assembly out of the mounting pin of the wheelchair frame.

3. Repeat STEPS 1-2 for opposite side, if necessary.

FIGURE 1 - INSTALLING/

REMOVING

SWINGAWAY

FOOTREST

Footrest Release Lever

Footrest

Assembly

Mounting Tube

Wheelchair

Frame

Footplate

NOTE: Only 60

Front Rigging shown for clarity.

Others will attach the same way.

Mounting Pin

Page is loading ...

Invacare 1106628 User manual

Brand: Invacare

Model: 1106628

Category: Strollers

Type: User manual

This manual is also suitable for

Download PDF

report

Invacare 1106628 User manual

This manual is also suitable for

Invacare 1106628 User manual

Related papers

Other documents