Viking Range VGBQ4103RT User manual

Brand: Viking Range

Model: VGBQ4103RT

Category: Barbecues & grills

Type: User manual

Viking Use & Care Manual

Outdoor Gas Grills

F20455F EN

(050311)

Viking Range Corporation

111 Front Street

Greenwood, Mississippi 38930 USA

(662) 455-1200

For product information

call 1-888-VIKING1 (845-4641),

or visit the Viking Web site at

vikingrange.com

Congratulations

Congratulations and welcome to the elite world of Viking

ownership. We hope you will enjoy and appreciate the care

and attention we have put into every detail of your new,

state-of-the-art grill.

Your Viking appliance is designed to offer years of reliable

service. This Use and Care Manual will provide you with the

information you need to become familiar with the care and

operation of your grill.

Your complete satisfaction is our ultimate goal. If you have any

questions or comments about this product, please contact the

dealer from whom you purchased it, or contact our Consumer

Support Center at 1-888-VIKING1.

We appreciate your choice of a Viking grill and hope that you

will again select our products for your other major appliance

needs.

For more information about the complete and growing

selection of Viking products, contact your dealer or visit us

online at vikingrange.com.

Warnings

WARNING

EXPLOSION HAZARD

Do not use the grill as storage area for

flammable materials. Keep area clear and free

from combustible materials, gasoline, and other

flammable vapors and liquids. Failure to do

so can result in death, explosion, or fire.

WARNING

To reduce the risk of fire, electric shock, or injury, read and

follow these basic precautions before operating your gas grill

or side burners.

WARNING

Before lighting the burners inspect the gas supply piping

or hose. If there is evidence of cuts, wear, or abrasion, it must

be replaced prior to use. Always keep your face and body as

far away from the grill as possible when lighting.

WARNING

ELECTRICAL SHOCK HAZARD

This unit is equipped with a grounding plug

for your protection against shock hazard and

should be plugged directly into a properly

grounded receptacle. Do not cut or remove

the grounding prong from this plug.

Keep all electric cords away from the heated surfaces of

the grill.

WARNING

Do not use flammable cleaning materials. Use a flashlight to

inspect the burner inlet to ensure it is not blocked. If

obstructions can be seen, use a metal wire coat hanger that

has been straightened out. Shake out any debris through the

air shutter.

Warnings (cont.)

WARNING

SPIDER AND INSECT INFESTATION

Spiders and insects can nest in the burners/venturi tubes of

this or any other grill, and cause the gas to flow from the front

of the burner. This is a very dangerous condition that can

cause a fire to occur behind the valve panel, thereby damaging

the grill and making it unsafe to operate.

CAUTION

Wait at least five minutes before relighting a hot grill to

allow any accumulated gas to dissipate. Keep a spray bottle of

soapy water near the gas supply valve and check the

connections for gas leaks before each use.

CAUTION

The side burner cover may be hot if the grill burners are in

operation.

CAUTION

Handle the smoker box with care. The cover becomes extremely

hot when being used. Use sturdy, properly insulated gloves or

dry potholders.

CAUTION

• Do not use a metal knife or any other metal tool to scrape

stainless steel parts.

• Do not permit citrus or tomato juice to remain on stainless

steel surfaces, as citric acid will permanently discolor stainless

steel. Wipe up any spills immediately.

• Do not use abrasive cleaners, steel wool pads, or abrasive

cloths on stainless steel, painted parts, or brass parts.

• Do not use brass cleaners on the brass option parts. They

feature an epoxy coating.

FOR YOUR SAFETY

1. Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

2. Do not store any propane/butane (G31-G30) cylinder

(that is not connected for use) in the vicinity of this or any

other appliance.

WARNING

This unit is for outdoor use only! Do not operate in a

building, garage or any other enclosed areas. This could

result in carbon monoxide buildup which could result in

injury or death.

DANGER

If you smell gas

1. Shut off gas to the appliance.

2. Extinguish any open flames.

3. Open lid.

4. If odor continues, immediately call your gas supplier.

WARNING

TO PROTECT AGAINST ELECTRIC SHOCK

1. Do not immerse cord or plugs in water or other liquids.

2. Unplug from outlet when not in use and before cleaning.

3. Do not operate any outdoor appliance with a damaged

cord, plug or after the appliance has malfunctioned. Contact

the manufacturer for repair.

4. Do not let the cord hang over the edge or touch hot

surfaces.

5. Use only extension cords with a 3-prong grounding plug;

rated for the power of the equipment and approved for

outdoor use with a W-A marking.

Important Safety Instructions

• Your unit should be properly installed and connected to the gas

for which it was designed. Do not use charcoal, wood chips, or

other material in your grill. The smoker tray is the only area

designed to hold wood chips or other smoke flavor enhancers.

• Have the technician show you the location of the gas shut-off

valve so you can shut off the gas supply in an emergency. If you

smell gas, the connections are not properly sealed or you may

have a hole in the gas supply pipe or hose. Determining where

the gas leak is should be left to a qualified technician. Warranty

service must be performed by an authorized service agency.

• Children should not be left alone or unattended in an area

where the gas grill is being used. Never allow children to sit,

stand or play on or around the grill at any time. Do not store

items of interest to children around the grill. Never allow

children to crawl inside the cart or masonry enclosure.

• Use a covered hand when opening the hood and do so slowly to

allow heat and steam to escape. To avoid burns when cooking,

use long handled BBQ tools. Never lean over an open grill.

• Use sturdy, properly insulated gloves or potholders. Dish towels

or other substitutes can become entangled, causing burns. Use

dry potholders; wet potholders create steam and cause burns.

Keep potholders away from open flames when lifting or moving

utensils. Do not touch portions of the grill rack or burner grate

with potholders until the hot surfaces have cooled.

• Only certain types of glass, heat-proof glass ceramic,

earthenware, or other glazed utensils are suitable for grill use.

These types of materials may break with sudden temperature

changes. Use only on low or medium heat settings.

• Select the correct pan size for the burner. Be sure the pan

is large enough to avoid boilovers or spillovers. This will

save cleaning, and prevent accumulations of food, heavy

splattering, or spillovers that can catch fire.

Getting Started

Table of Contents

Getting Started

Important Safety Instructions ______________________7

Features ___________________________________________ 10

Before Lighting Grill _______________________________ 11

Using Grill with Outdoor Approved Hoods _________ 11

Operation

Lighting Grill ______________________________________12

Using Grill _________________________________________16

Cooking Tips ______________________________________17

Grilling Tips _______________________________________20

Smoker Box _______________________________________ 21

Rotisserie __________________________________________22

Product Care

Cleaning and Maintenance ________________________24

Battery Replacement ____________________________ 29

Troubleshooting ___________________________________ 31

Service Information ________________________________ 32

Warranty __________________________________________ 33

WARNING

To reduce the risk of fire, electric shock, or injury, read and

follow these basic precautions before operating your gas grill

or side burners.

Important Safety Instructions

• When cooking in windy conditions, provide a wind break.

Locate the unit with proper clearance from combustible

surfaces.

• Spiders and insects can nest in the burners of the grill and

block the gas and air flow to the burner ports. This may

cause a fire from behind the manifold cover. Inspect and

clean the burners periodically.

• Keep the ventilation openings at the rear of the cart and

cylinder enclosure free and clear to allow proper flow of air.

Do not obstruct the flow of combustion and ventilation air.

• Clothing fires are potential hazards. Do not wear long

flowing sleeves around the grill. They are easily caught on

pan handles or ignited by burners and are generally in the

way. Highly flammable clothing—especially synthetic

fabrics—should not be worn while cooking.

• Do not heat any unopened glass or metal containers on the

grill. Pressure may build up and cause the container to burst,

resulting in serious personal harm or damage to the grill.

• Do not move the appliance during use.

• Be sure all controls are turned off and the grill is cool before

using any type of aerosol cleaner on or around the grill. The

chemical that produces the spraying action could, in the

presence of heat, ignite or cause metal parts to corrode.

• Do not remove the plastic cover on the rotisserie motor

switch due to safety considerations.

• If the following instructions are not followed exactly, a fire

causing death or serious injury may occur.

Do not store a spare gas cylinder under or near this appliance.

Never fill the cylinder beyond 80 percent full.

Getting Started

Important Safety Instructions

• Never leave the grill unattended. High flames and fatty

meats will promote flare ups.

• When using the grill, do not touch the grill grates, open

burner grates, or immediate surrounding areas. These

surfaces become extremely hot and could cause burns. Be

sure all controls are turned off and the unit has cooled

before touching or cleaning any surfaces.

• Do not use aluminum foil to line drip pans or grill racks. This

can upset combustion air flow or trap excessive heat in the

control area, resulting in melted knobs.

• The handle of your cooking utensil should be positioned so

that it does not extend over adjacent surface burners or

interfere with closing the canopy. This will minimize burns,

ignition of flammable materials, and possible spillage. Let

hot pans cool in a safe place out of children’s reach.

• Never grill without the drip tray in place. Make sure it is

pushed all the way to the back—in proper position—to catch

the drippings. Let the grease cool before attempting to

remove for cleaning or disposal. Do not allow large amounts

of grease to accumulate in the drip tray as it can catch on fire.

• Before storing, make sure the gas grill is cool. The gas must

be turned off at the supply tank, removed, and stored

outside in a well-ventilated area out of the reach of children.

• Keep all electric cords away from heated areas of the grill.

Getting Started

WARNING

Before lighting the burners inspect the gas supply piping

or hose. If there is evidence of cuts, wear, or abrasion, it

must be replaced prior to use. Always keep your face and

body as far away from the grill as possible when lighting.

WARNING

This unit is for outdoor use only! Do not operate in a

building, garage or an other enclosed areas. This could

result in carbon monoxide buildup which could result in

injury or death.

WARNING

EXPLOSION HAZARD

Do not use the grill as storage area for

flammable materials. Keep area clear and free

from combustible materials, gasoline, and other

flammable vapors and liquids. Failure to do so

can result in death, explosion, or fire.

Before Lighting Grill

Getting Started

1. Electronic ignition

2. Pull out drip tray

3. Side burner control knobs

(if applicable)

4. Rotisserie control knob

5. 9V battery—behind control

panel

6. Grill burner control knobs

7. 9V battery—behind control

panel (some models)

8. Interior light switch

(E-Series)

9. Porcelain grids w/stainless

steel flavor generators

underneath

10. Smoker box

11. Rotisserie bracket

12. Rotisserie motor

13. Spit rod w/forks

14. Warming rack

(if applicable)

15. Infrared rotisserie burner

16. Interior lights (E-Series)

17. Side burner

(if applicable)

18. Canopy

Prior to turning on the gas, inspect the gas supply tubing or

hose. Look for evidence of abrasion, cuts, wear and tear, or

other damage which could require replacement prior to use.

Make sure all burner control knobs are off. Do not attempt to

light the burners if the smell of gas is present.

Check the connection with a soap and water solution after

attaching the hose. Make sure there is gas in the tank and the

tank is upright.

CAUTION

Wait at least five minutes before relighting a hot grill to allow

any accumulated gas to dissipate. Keep a spray bottle of soapy

water near the gas supply valve and check the connections for

gas leaks before each use.

Features

NOTE: Control locations will vary according to model.

beFlash tube

Flash tubeFlash tubeFlash tube

Place the tabs on rear of stainless

steel flavor generator plates into slots

on rear panel.

Lower stainless steel flavor generator plates

so the front tabs rest on the grill frame.

Note: The flash tube must be accessible

through the plates. If the flash tube is not

accessible, the flavor generator plates are

not properly installed.

Flavor Generator Plates Proper Installation

Using Grill with Outdoor Approved Hoods

• Outdoor approved hood models should be installed in a covered yet non-

enclosed (well ventilated) area. Outdoor hoods aid greatly in smoke and

odor removal, but should not be expected to eliminate entirely. They should

also be protected from natural elements (such as rain) as much as possible.

• ALWAYS turn the outdoor hood to the “HIGH” position before lighting the

grill.

• Keep the grill canopy closed as much as possible when cooking so smoke is

exhausted out the back of the grill. This allows optimum performance of the

hood.

• During breezy conditions, the performance of the outdoor hood may be

compromised.

Operation

Lighting Grill

Lighting TruSear™ Infrared Burner (If Applicable)

Before lighting the burner, remove the stainless steel cover.

Push in and turn the TruSear™ infrared control knob until the

“HIGH” position on the knob aligns with the indicator line on

the control panel. Press the electronic ignition button that

corresponds to the control knob. You will hear a clicking

sound. Once lit, turn the control knob to the desired setting.

If the burner does not light within 4 seconds, release and

turn the control knob to “OFF.” Wait 5 minutes for any

accumulated gas to dissipate and try again. After several

failed attempts, the burner may be lit by turning the control

knob to “HIGH” and dropping a match on the face of the

burner. If the burner does not immediately ignite, turn the

knob to “OFF”, wait 5 minutes and try again.

Lighting Side Burners

First, remove the burner cover or any cooking utensil from the

burner grate.

Push and turn the control knob until the “HIGH” position

aligns with the indicator line on the control panel.

Immediately press the electronic ignition button

corresponding to the burner(s) being lit until the burner is

lit or until 4 seconds pass. If the burner does not light

after several attempts, wait five minutes to allow any

accumulated gas to dissipate. If the burner will not light after

several attempts, then the burner can be lit by holding a lit

match next to the burner ports. Push and turn the control

knob until the “HIGH” position on the knob aligns with the

indicator line on the control panel.

CAUTION

The side burner cover may be hot if the grill burners are in

operation.

Lighting Grill

T-Series Models

When lighting a burner, always pay close attention to what

you are doing. Be certain you are pressing the battery

ignition button (T-Series only) corresponding to the burner

you are lighting.

Lighting Grill Burners

Open the hood or remove covers. Push and turn the control

knob until the “HIGH” position on the knob aligns with the

indicator line on the control panel. Press the electronic

ignition button corresponding to the burner being lit. You

will hear a clicking sound. Turn the control knob to the

desired setting. If the burner does not light in 4 seconds,

turn the knob to “OFF” and wait 5 minutes before trying

again. This will allow accumulated gas to dissipate. After

several failed attempts the burner can be lit with a paper

book match using the flash tubes. If you have just attempted

to light the burner with the ignitor, allow 5 minutes for any

accumulated gas to dissipate.

Electronic

ignitor

Side burner

control knob

NOTE: Control locations

will vary according to model.

Grill burner

control knob

Rotisserie

control knob

Flash tubeFlash tubeFlash tube

Place the lit match through the grid next to the flash tube of

the burner being lit. Keep your face as far away from the grill

as possible. Make sure the match is adjacent to the flash tube.

Push and turn the control knob until the “HIGH” position on

the knob aligns with the indicator line on the control panel.

Make sure you are turning the control knob that corresponds

with the burner being lit. If the burner does not light in 4

seconds, turn the knob to “OFF,” wait 5 minutes, and try

again. If the burner will not light after several attempts, see

the Troubleshooting section.

Operation

Lighting Grill

Operation

Lighting the Grill Burners (E-Series Models)

Make sure the unit is plugged into a properly grounded

receptacle. Turn the appropriate control knob counter-

clockwise to any position. This control is both a gas valve and

an electric switch. Burners will ignite at any “ON” position

with the automatic re-ignition system. If the flame goes out

for any reason, the burners will automatically re-ignite if the

gas is still flowing. When gas is permitted to flow to the

burners, the electric igniters start sparking. On all surface

igniters you should hear a clicking sound. If you do not, turn

off the control and check that the unit is plugged in and that

the fuse or circuit breaker is not blown or tripped.

Within a few moments, enough gas will have traveled to the

burner to be able to light. When the burner lights, turn the

burner control to any position to adjust the flame size. If the

burner does not light in 4 seconds, turn the knob to “OFF”

and wait 5 minutes before trying again. This will allow

accumulated gas to dissipate. After several failed attempts

the burner can be lit with a paper book match using the flash

tubes.

If you have just attempted to light the burner with the ignitor,

allow 5 minutes for any accumulated gas to dissipate. Place

the lit match through the grid next to the flash tube of the

burner being lit. Keep your face as far away from the grill as

possible. Make sure the match is adjacent to the flash tube.

Push and turn the control knob until the “HIGH” position on

the knob aligns with the indicator line on the control panel.

Make sure you are turning the control knob that corresponds

with the burner being lit. If the burner does not light in 4

seconds, turn the knob to “OFF,” wait 5 minutes, and try

again. If the burner will not light after several attempts, see

the Troubleshooting section.

Lighting Infrared Rotisserie Burner

(T-Series and E-Series Models)

The location of the infrared burner makes it more susceptible

to strong wind conditions—more so than the protected grill

burners. For this reason you should avoid using it during

windy conditions.

Open the canopy. Push in and turn the rotisserie control knob

until the “HIGH” position on the knob aligns with the

indicator line on the control panel and continue to hold in the

knob. Press the electronic ignition button which corresponds

to the rotisserie control knob. You will hear a clicking sound.

After the burner lights, hold the rotisserie control knob in

about 5 seconds longer or until the burner remains lit. Once

lit, turn the control knob to the desired setting. If the burner

does not light within 4 seconds, release and turn the control

knob to “OFF”. Wait 5 minutes for any accumulated gas to

dissipate. If the burner does not light after several attempts,

then the burner can be lit by holding a lit match to the burner

(with the control knob pushed in at the light position). Push

and turn the control knob until the “HIGH” position on the

knob aligns with the indicator line on the control panel. Make

sure you are turning the control knob that corresponds with

the burner being lit. If relighting a hot burner, wait 5 minutes.

Never leave the rotisserie control knob at “ON” if

rotisserie is not in use.

Flash tubeFlash tubeFlash tube

Lighting Grill

Operation

Using Grill

Before You Begin

• The first time you use the grill, turn the control knob to

“HIGH” and preheat racks for an additional 15 — 20

minutes. This allows the porcelain grates to be “seasoned.”

• Before each use, turn the control knob to “HIGH” and

preheat for 5 — 7 minutes.

• Check to be certain the drip tray is in place.

• Light the grill burners using the lighting instructions.

• Place the food on the grill and cook to the desired

doneness. Adjust heat setting, if necessary. The control

knob may be set to any position between “HIGH” and

“LOW.”

• Allow grill to cool before cleaning. (Drip tray should be

cleaned after each use.)

Canopy Thermometers (If Applicable)

Your outdoor grill is equipped with a thermometer on the

canopy. The thermometer is designed to aide in the

preheating of the grill and closed canopy grilling. The

estimated cooking temperatures with the canopy closed are:

°F

450

750

200

WARM 150˚F (65˚C)

COLD SMOKE 150˚F — 200˚F (65˚C — 93˚C)

SMOKE 200˚F — 300˚F (93˚C — 149˚C)

GRILL 300˚F — 750˚F (149˚C — 399˚C)

Canopy Thermometer

Cooking Tips

Grilling can be either an open or closed canopy process.

Open canopy grilling is excellent for foods requiring quick

searing like steaks, burgers, chops, and hot dogs. Closed

canopy grilling is similar to roasting in an oven. Food is

cooked by heat reflection from the cover as well as heat from

the burners below.

• When grilling chicken, roasts, well-done steaks or chops,

and thick pieces of meat, sear on “HIGH.” Then reduce the

heat setting to prevent excessive flareup. This will allow the

food to cook through without burning on the outside.

• When grilling large pieces of meat, use a meat thermometer

to ensure that meats are either rare, medium or well-

cooked.

• After steaks, chops, or hamburgers have been allowed to

sear for approximately 1 minute, you might want to slide a

spatula under the meat and turn it approximately 90˚ so that

a waffle pattern will be seared onto the food.

• Use a metal spatula or tongs instead of a fork to turn the

meat. A fork will puncture the meat, allowing juices to

escape.

• Turn the meat over only once. Juices are lost when steaks,

chops, or hamburgers are turned several times. The best

time to turn the meat is after the juices have begun to

bubble to the surface.

• To test for doneness, make a small slash in the center of the

meat, not across the edge. This will prevent loss of juices.

• Occasionally there may be flare-ups or flames above the

grill due to drops of fat falling onto the flavor generator

plates. It is normal to have some flare-up during grilling. If

necessary, use a long spatula to move food to another area

until the flames subside.

Operation

Cooking Tips

Food

Weight or

thickness

Control

setting

Total

suggested

cooking time*

Special

instructions

and tips

BEEF

Hamburgers 1/2” (1.3 cm) –

3/4” (1.9 cm)

Med 8 – 15 min.

Grill, turning once

hen juices rise to the

surface. We suggest

that ground chuck be

used for hamburgers,

as it will give you a

juicier hamburger. Do

not leave hamburgers

unattended since a

flare-up could occur

quickly.

STEAKS

Rib, club,

sirloin,

t-bone,

porterhouse

Rare

140˚F/60˚C

Medium

160˚F/71˚C

Well-done

170˚F/77˚C

Tenderloin

1” (2.5 cm) –

1-1/2” (3.8 cm)

1” (2.5 cm) –

1-1/2” (3.8 cm)

1” (2.5 cm) –

1-1/2” (3.8 cm)

5 lbs (0.3 kg)

High

Med

Med-High

High

8 – 12 min.

11 – 16 min.

10 – 12 min.

16 – 25 min.

20 – 30 min.

25 – 35 min.

30 – 40 min.

Remove excess fat

from edge. Slash

remaining fat at 2”

intervals to keep

edges from curling.

Grill, turning once

Remove surface fat

and fatty tissue. Fold

over thin end to form

uniformly thick piece.

Bind with string. Grill,

turning as needed to

brown evenly. Brush

often with melted

margarine or oil.

POULTRY

Chicken

halves or

quarters

2 lbs (0.9 kg) –

3 lbs (1.4 kg)

Med-High

1 – 1-1/2 hours

40 – 60 min.

Place skin side up.

Grill, turning and

brushing frequently

with melted

butter or oil.

PORK

Chops 1/2” (1.3 cm) –

1” (2.5 cm)

Med

–

40 min.

–

60 min.

Remove excess fat

from edge. Slash

remaining fat at 2”

intervals to keep edge

from curling. Grill,

turning once, and

moving if necessary

*These times are recommendations only. Variations in cuts of meats and

personal taste may alter cooking times. Use your discretion when grilling.

Cooking Tips

Food

Weight or

thickness

Control

setting

Total

suggested

cooking time*

Special

instructions

and tips

PORK

Ribs

Ham steaks

Hot dogs

1/2” (1.3 cm)

Med

High

Med

45 – 60 min.

12 – 15 min.

5 – 10 min.

Grill, turning

occasionally. During

ast few minutes brush

with BBQ sauce, turn

several times.

Remove excess fat

from edge. Slash

remaining fat at

2” intervals. Grill,

turning once.

Slit skin before

cooking. Grill, turning

once.

Fish

Steaks

Halibut

Salmon

Swordfish

Whole

Catfish

Trout

3/4” – 1”

(0.9 – 1.4 kg)

4 – 8 ounces

(110 – 230 g)

Med-High

5 – 10 min.

10 – 12 min.

Grill, turning once.

Brush with melted

butter, oil, or marinade

to keep fish moist.

Grill, turning once.

Brush with melted

butter, oil, or marinade

to keep fish moist.

Vegetables

Carrots

Onions

Potatoes

Zucchini,

squash

Whole

Sliced (halves

or quarters)

Med-Low

Low

Med

35 – 40 min.

20 min.

45 – 50 min.

30 min.

Scrub, don’t peel.

Wrap in foil and lay

directly on grill grate.

Butter, wrap in foil.

Turn often.

Oil, wrap in foil.

Turn often.

Butter lightly

prevent sticking.

*These times are recommendations only. Variations in cuts of meats and personal

taste may alter cooking times. Use your discretion when grilling.

Operation

Grilling Tips

TruSear™ Infrared Grilling Tips

Infrared grilling produces intense heat which quickly sears the meat.

Searing locks in flavor and juices while allowing the outer surface to

absorb smoke and food aroma that is produced as grease and

drippings are vaporized by the burner. The result is a crisp, flavorful

outside with a tender, juicy inside. As a general rule, foods will cook in

about half the time they would take on an ordinary grill.

• Preheat the grill.

• Ensure that meat is fully thawed and that all excess fat is trimmed

away prior to grilling.

• Leave the burner set on “HIGH” when placing food on the grill to

sear.

• For thicker cuts of meats, adjust burner to a lower setting and

continue cooking until desired doneness is reached.

NOTE: When the TruSear™ infrared burner is not use, it must be

covered with the provided stainless steel cover for protection from

outside elements such as rain.

Food

Thickness

Control

setting

Suggested

cooking time*

Chicken breast,

boneless

N/A High

Reduce to

Med

2 – 3 mins. each side

cook 8 – 10 mins. total

Turn occasionally to

prevent burning outside.

Hamburger

1/2 - 3/4” thick High

2 mins. each side to sear.

cook 6 – 8 mins. total.

Turn occasionally to

prevent burning.

Steaks, ribeye 1-1/2” thick High

3 mins. each side for rare.

4 mins. each side for

medium.

Steaks, filet 1” thick High

3 mins. each side for rare to

med. rare. 3-1/2 mins each

side for medium.

Pork chops 3/4” thick High

4 mins. each side.

*These times are recommendations only. Variations in cuts of meats

and personal taste may alter cooking times. Use your discretion when

grilling.

TruSear™ Infrared Cooking Chart

Using the smoker box

feature intensifies the

flavor by adding smoke to

the grilling process. The

additional smoke creates a

“cloud” around the food

which permeates meats

and vegetables for added

smoky flavor. In order to

use the smoker box,

remove the last set of

porcelain grids on the right

hand side of the grill. Set

the smoker box in the

opening so that the front

and rear tabs rest on the

grill frame.

Wood Chip Use in Smoker Box

There are many wood chips available and selection is based

on personal taste. The most common chips used are mesquite

or hickory. Always soak the chips in water prior to putting

them into the box. Use the “HIGH” position to start the chips

smoking, then reduce the heat to a lower level to prevent

them from drying out and flaming. If the wood chips do flame

up, add a small amount of water to extinguish the flame. Use

caution when adding water to a hot box to avoid steam

burns. This tray may also be filled with water to produce

steam. Whether smoking or steaming, the grill should remain

closed as much as possible to maximize the effect.

During extended roasting periods, it is normal to add fresh

wood chips and water to the box several times. Limit the

amount of times the canopy is opened—each peek adds

about 15 minutes to the cooking time.

Smoker box

CAUTION

Handle the smoker box with care. The cover becomes

extremely hot when being used. Use sturdy, properly

insulated gloves or dry potholders.

Smoker Box

Operation

Rotisserie

The rotisserie burner is an infrared burner which provides

intense searing radiant heat. Preferred by professional chefs

over other methods, this intense heat is great for searing in

the natural juices and nutrients found in quality cuts of meat.

Once lit, the rotisserie burner will reach cooking temperatures

in about 1 minute. The red glow will even out in about 5

minutes.

To install the rotisserie motor, align the drive shaft on the

motor with the gear box on the side of the grill. Tighten the

thumb screws on the motor into the mounting brackets on the

grill frame. The skewer for the rotisserie is assembled into the

gear box assembly by placing the pointed end into the gear

box and resting the rounded end on the wheels on the left

side of the grill.

WARNING

ELECTRICAL SHOCK HAZARD

This unit is equipped with a grounding plug

for your protection against shock hazard and

should be plugged directly into a properly

grounded receptacle. Do not cut or remove

the grounding prong from this plug.

Keep the rotisserie motor electric cord away from the

heated surfaces of the grill.

Motor

Skewer

Gear box

Mounting bracket

Thumb screws

Rotisserie fork

Rotisserie

To load the skewer, slide one of the rotisserie forks (prongs

facing away from the end) onto the skewer. Push the skewer through

the center of the food, then slide the second rotisserie fork (prongs

toward the food) onto the skewer. Center the product to be cooked on

the skewer then push the forks firmly toward the food. Tighten the

wing nuts with pliers. It may also be necessary to wrap the food with

butcher’s string to secure loose portions. Never use nylon or

plastic string. Once the food is secure, insert the skewer into the

motor. To turn on rotisserie motor, flip the ON/OFF switch located on

the rotisserie motor assembly.

If needed, remove the grill grates. Place the basting pan beneath the

food. Keep canopy closed while using the rotisserie. Each peek adds

about 15 minutes to the cooking time. A meat thermometer should be

used when cooking large pieces of meat to ensure that the meats are

rare, medium, and well cooked.

Food

Weight

Control

setting

Suggested

cooking time*

Internal

temperature

Beef rib roast 4 – 6 lbs. Med-High Rare

14 – 16 min./lb.

Medium

23 – 25 min./lb.

145˚F

160˚F

Bnls tip roast 4 – 6 lbs. Med-High Rare

14 – 16 min./lb.

Medium

23 – 25 min./lb.

145˚F

160˚F

Bone-in pork butt 3 – 5 lbs Med-Low 15 – 18 min./lb. 170˚F

Bnls pork loin 3 – 5 lbs Med 22 – 25 min./lb. 170˚F

Smoked ham half 5 – 7 lbs Med 22 – 25 min./lb. 170˚F

Chicken

Whole fryer

Quarters

2 – 4 lbs Med

Med-High

25 – 30 min./lb.

20 – 22 min./lb.

180˚F

Turkey

Whole

Breast

12 – 14 lbs

5 – 6 lbs

Med-High

16 – 18 min./lb.

22 – 25 min./lb.

180˚F

170˚F

Cornish hens 1-1/2 – 2 lbs. Med 22 – 25 min./lb. 180˚F

*The above information is given as a guide only. You may need to vary the heat

settings and times due to factors such as weather, climate and/or personal

requirements.

Rotisserie Cooking Chart

Product Care

Cleaning and Maintenance

Any piece of equipment works better and lasts longer when

maintained properly and kept clean. Grilling equipment is no

exception. Your grill must be kept clean and maintained properly.

Viking highly recommends cleaning the grill after each use. A

Viking grill cover (sold separately) should also be strongly

considered in order to protect your grill from the elements.

Porcelain Grates/Flavor Generator Plates/Grill

Burners

The porcelain grill grates are easily cleaned immediately after

cooking is complete and before turning off the flame. Wearing a

barbecue mitt to protect your hand from heat, use a stainless or

brass bristle barbecue brush to scrub the porcelain burner grid.

Dip the brush frequently in a bowl of water. Steam is created as

the water contacts the hot grate. The steam assists the cleaning

process by softening the food particles. IMPORTANT: It is critical

that the flavor plates not be allowed to develop excess build-up

of debris over an extended period. Extreme flare-up may occur.

For thorough cleaning of the grates and plates, allow to cool,

then soak 15 to 30 minutes in a hot water and detergent solution.

After soaking, scrub with a teflon scouring pad. Do not use a

steel wool pad or abrasive cleaners. They could damage the

porcelain finish.

Before removing the grates and burners, make sure the gas

supply is off and the knobs are in the “OFF” position. To

disassemble the grill for thorough cleaning, remove parts after

they have cooled in the following order.

Remove porcelain grill grates.

Remove flavor generator plates.

Cleaning and Maintenance

Product Care

Unclip holding tab at

the rear of each burner.

Remove burner from holding

tab at rear of burner.

Remove burner from slots located in front

mounting bracket.

Product Care

Cleaning and Maintenance

WARNING

Do not use flammable cleaning materials. Use a flashlight to

inspect the burner inlet to ensure it is not blocked. If obstructions

can be seen, use a metal wire coat hanger that has been

straightened out. Shake out any debris through the air shutter.

Burner

outlet

Remove the grates, burner bowls, and

grate support.

Remove bolts from side burners.

Removing Optional Side Burners for cleaning

Lift side burners and separate air shutter

from orifice.

Cleaning and Maintenance

TruSear™ Infrared Grill Burner (If Applicable)

When finished cooking, turn the control knob to the “HIGH”

setting and allow the burner to burn for 5 minutes. This helps

eliminate any drippings or debris that would otherwise remain

on the burner, degrading the performance and reducing

burner life. After the 5 minute burn-off time, turn the grill

“OFF” and allow to cool completely before attempting to

clean or move. Wipe excess grease and food from grill

surfaces.

NOTE: When the TruSear™ infrared burner is not use, it must

be covered withthe provided stainless steel cover for

protection from outside elements such as rain.

Drip Tray

The drip tray pans should be

removed and cleaned after each use.

Allow the drippings in the the drip tray

pans to cool completely before

removing. To remove the drip

tray pans, simply remove the

pans from the tray. Place the

trays in hot, soapy water to

clean. Wipe up any

debris that may

have collected in

the drip tray with a hot,

soapy towel. Dry and

replace drip tray pans before

next use.

CAUTION

• Do not use a metal knife or any other metal tool to scrape

stainless steel parts.

• Do not permit citrus or tomato juice to remain on stainless

steel surfaces, as citric acid will permanently discolor

stainless steel. Wipe up any spills immediately.

• Do not use abrasive cleaners, steel wool pads, or abrasive

cloths on stainless steel, painted parts, or brass parts.

• Do not use brass cleaners on the brass option parts. They

feature an epoxy coating.

Product Care

Cleaning and Maintenance

Infrared Rotisserie Burner

Special care is not required for the infrared rotisserie burner. It

is designed as a self-contained unit. Do not attempt to clean it. Its own

operation burns off any impurities which may condense on it.

Individual part cleaning chart

Part

What to use How to clean

Stainless steel* Mild detergent and warm

water or stainless steel

cleaner

Wipe with soft cloth or

sponge. Use stainless steel

cleaner to remove fingerprints

and smudges. Rinse and dry

thoroughly.

Porcelain parts

(Grates)

Mild detergent and warm

water or nonabrasive

household cleaners.

Wipe with soft cloth or

sponge. Rinse and dry

thoroughly. For stubborn

spots, occasionally use a

non-caustic oven cleaner

(fume free).

Flavor Plates Mild detergent and

warm water or stainless

steel cleaner

Soak in warm water and mild

detergent. For stubborn

spots, scrub with stainless or

brass bristle BBQ brush. Wipe

down with heavy-duty cloth or

sponge. Dry thoroughly.

Control knobs Mild detergent and

warm water or

nonabrasive household

cleaners. Do not soak.

Wipe with soft cloth or

sponge. Rinse and dry

thoroughly.

Painted parts

(Canopy)

Mild detergent and warm

water or nonabrasive

household cleaners

Wipe with soft cloth or

sponge. Rinse and dry

thoroughly.

*NOTE: Under rare conditions, such as an extremely salty environment, small

amounts of rust may accumulate on stainless steel parts. These small amounts

of surface rust can easily be removed by applying Soft Scrub® Gel to a damp

sponge and wiping with the stainless steel grain. It is important to make sure

you wipe with the grain for the most efficient removal of surface rust.

Cleaning and Maintenance

Battery Replacement

Each T-Series grill is equipped with a battery for the electronic

ignition. The 30”W. models only have one battery located

under the left hand side of the control panel. All other models

have two batteries located under each end of the control

panel. The battery locations are shown on the control panel.

To replace the battery:

1. Slide out drip tray.

2. Locate round black cap, which is inside the burner box

under the battery symbol on the control panel.

3. Unscrew cap. Battery is snapped in the cap.

4. Replace the battery by connecting corresponding post to

post inside burner box.

5. Snap cap on battery and screw back into slot underneath

control panel.

Battery

cap

BatteryBatteryBattery

NOTE: Round black cap that holds

battery is located underneath

control panel and behind drip tray.

Product Care

Spider Inspection

You should inspect the burners/venturi tubes at least once a year, or

immediately if any of the following conditions occur.

• The smell of gas along with the burner flames appearing yellow.

• The grill does not reach the proper temperatures.

• The grill heats unevenly.

• The burners make a popping noise.

Cleaning and Maintenance

WARNING

SPIDER AND INSECT INFESTATION

Spiders and insects can nest in the burners/venturi tubes of this

or any other grill, and cause the gas to flow from the front of the

burner. This is a very dangerous condition that can cause a fire

to occur behind the valve panel, thereby damaging the grill and

making it unsafe to operate.

Troubleshooting

PROBLEM POSSIBLE CAUSE AND/OR REMEDY

T-Series grill won’t light when

the ignitor is pressed

Make sure the control knob is off (no gas

is on). Remove the grill rack and the flavor

generator plates. Watch the ignitor tip. You

should see a spark jump from the tip of the

ignitor when the button is pressed. Do the

other burners work? Make sure the ignitor

tip is clean and free from debris. Check

battery to electronic ignition.

Burner flame is yellow or

orange and a gas odor is

present

Check the burner inlet for obstructions.

Check the air shutter for proper adjustment.

Low heat with knob on

“HIGH”

Is the fuel hose bent or kinked? Is there

adequate gas supply available? If only one

burner appears low, does the orifice or

burner need cleaning? Are any other gas

appliances at the location below normal

rate? Is the air shutter too far open or

closed? Is the gas supply or gas

pressure low?

Burner will not light Is there a spark at the thermocouple? Can

you match light the burner using the flame

parts?

Burner lights, but will not

hold flame once button is

released

Is the thermocouple kinked or bent away

from the burner? Readjust to lay flat against

burner. Is the safety valve button being

depressed long enough? Hold button in

until burner remains lit. Check for black

spots on the infrared screen.

If your grill rotisserie should

fail to operate

Is the electrical cord securely inserted in the

electrical outlet?

Is the circuit breaker open,

or is a fuse blown?

Replacing Interior Halogen Canopy Lights

Do not touch bulb with bare hands. Clean off any signs of oil

from the bulb and handle with a soft cloth.

CAUTION

DISCONNECT THE ELECTRIC POWER BEFORE REPLACING

BULB.

1. Unsnap glass light cover

using a screwdriver in the

access groove.

2. Firmly grasp light bulb and

pull out.

3. Replace with halogen bulb

using volt and wattage

requirements listed on glass

cover.

4. Replace the light cover by

snapping glass cover onto

metal box.

5. Reconnect power.

access

groove

light

bulb

glass light

cover

Product Care

Service Information

If service is required, call your dealer or authorized service

agency. The name of the authorized service agency can be

obtained from the dealer or distributor in your area.

Have the following information readily available.

• Model number

• Serial number

• Date purchased

• Name of dealer from whom purchased

Clearly describe the problem that you are having. If you are

unable to obtain the name of an authorized service agency, or if

you continue to have service problems, contact Viking Range

Corporation at (888) 845-4641, or write to

VIKING RANGE CORPORATION

PREFERRED SERVICE

1803 Hwy 82W

Greenwood, Mississippi 38930 USA

Record the information indicated below. You will need it if

service is ever required. The model and serial number for your

grill is located on an identification plate located under the drip

tray in the rear left corner next to the inlet pipe.

Model no. _____________________ Serial no. ________________

Date of purchase __________ Date installed ________________

Dealer’s name __________________________________________

Address ________________________________________________

_______________________________________________________

If service requires installation of parts, use only authorized parts

to insure protection under the warranty.

Keep this manual for future reference.

Warranty

PROFESSIONAL SERIES OUTDOOR GAS GRILL WARRANTY

ONE YEAR FULL WARRANTY

utdoor gas grills and all of their component parts, except as detailed below*, are warranted to be free from

efective materials or workmanship in normal household use for a period of twelve (12) months from the date of

riginal retail purchase. Viking Range Corporation, warrantor, agrees to repair or replace, at its option, any part

which fails or is found to be defective during the warranty period.

*Painted and decorative items are warranted to be free from defective materials or workmanship for a period of

ninety (90) days from the date of original retail purchase. ANY DEFECTS MUST BE REPORTED TO THE SELLING

DEALER WITHIN NINETY (90) DAYS FROM DATE OF ORIGINAL RETAIL PURCHASE. Viking Range Corporation

ses the most up-to-date processes and best materials available to produce all color finishes. However, slight

olor variation may be noticed because of the inherent differences in painted parts and porcelain parts as well as

ifferences in kitchen lighting, product locations, and other factors.

FIVE YEAR LIMITED WARRANTY

Any burner assemblies, TruSear™ infrared burner, infrared rotisserie burner, or porcelain grill grate which fails due

to defective materials or workmanship in normal household use during the second through fifth year from the

date of original retail purchase will be repaired or replaced, free of charge for the part itself, with the owner

aying all other costs, including labor. Corrosion, scratching, and discoloration due to improper use and care of

he outdoor product is excluded from this warranty.

IFETIME LIMITED WARRANTY

Any stainless steel part or porcelain grill grate which rusts through due to defective materials or workmanship in

normal household use during the fifth through the useful lifetime of the grill from the date of original retail

purchase will be repaired or replaced, free of charge for the part itself, with the owner paying all other costs,

including labor.

NINETY (90) DAY RESIDENTIAL PLUS WARRANTY. This warranty applies to applications where use of the

product extends beyond normal residential use. Examples are, but not limited to, bed and breakfasts, fire

stations, private clubs, churches, etc. This warranty excludes all commercial locations such as restaurants, food

service locations and institutional food service locations.

This warranty extends to the original purchaser of the product warranted hereunder and to each transferee owner

of the product during the term of the warranty.

This warranty shall apply to products purchased and located in the United States and Canada. Products must be

purchased in the country where service is requested. Warranty labor shall be performed by an authorized Viking

Range Corporation service agency or representative. Warranty shall not apply to damage resulting from abuse,

accident, natural disaster, loss of electrical power to the product for any reason, alteration, improper installation,

improper operation, or repair or service of the product by anyone other than an authorized Viking Range

Corporation service agency or representative. This warranty does not apply to commercial usage. Warrantor is

not responsible for consequential or incidental damage whether arising out of breach of warranty, breach of

contract, or otherwise. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you.

Owner shall be responsible for proper installation, providing normal care and maintenance, providing proof of

purchase upon request, and making the appliance reasonably accessible for service. If the product or one of its

component parts contains a defect or malfunction during the warranty period, after a reasonable number of

attempts by the warrantor to remedy the defects or malfunctions, the owner is entitled to either a refund or

replacement of the product or its component part or parts. Warrantor’s liability on any claim of any kind, with

respect to the goods or services covered hereunder, shall in no case exceed the price of the goods or service or

part thereof which gives rise to the claim.

WARRANTY SERVICE: Under the terms of this warranty, service must be performed by a factory authorized

Viking Range Corporation service agent or representative. Service will be provided during normal business

hours, and labor performed at overtime or premium rates shall not be covered by this warranty. To obtain

warranty service, contact the dealer from whom the product was purchased, an authorized Viking Range

Corporation service agent, or Viking Range Corporation. Provide model and serial number and date of original

purchase. For the name of your nearest authorized Viking Range Corporation service agency, call the dealer from

whom the product was purchased or Viking Range Corporation. IMPORTANT: Retain proof of original purchase

to establish warranty period.

The return of the Owner Registration Card is not a condition of warranty coverage. You should, however, return

the Owner Registration Card so that Viking Range Corporation can contact you should any question of safety

arise which could affect you.

Any implied warranties of merchantability and fitness applicable to the above described burner assemblies,

infrared rotisserie burners, porcelain grill grates, and stainless steel parts are limited in duration to the period of

coverage of the applicable express written limited warranties set forth above. Some jurisdictions do not allow

limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty

gives you specific legal rights, and you may also have other rights which may vary from jurisdiction to jurisdiction.

Specifications subject to change without notice.

3534

Viking Range VGBQ4103RT User manual

Brand: Viking Range

Model: VGBQ4103RT

Category: Barbecues & grills

Type: User manual

Download PDF

report

Viking Range VGBQ4103RT User manual

Viking Range VGBQ4103RT User manual

Related papers

Other documents