Python 650ESP User manual

Brand: Python

Model: 650ESP

Category: Car alarm

Type: User manual

This manual is also suitable for

429 Series

Owner's Guide

1999 Directed Electronics, Inc.

Limited Lifetime

Consumer Warranty

Directed Electronics, Inc. ("DEI

") promises to the original purchaser to repair or

replace with a comparable reconditioned model any DEI unit (hereafter the "unit"),

excluding without limitation the siren, the remote transmitters, the associated sen-

sors and accessories, which proves to be defective in workmanship or material under

reasonable use during the lifetime of the vehicle provided the following conditions

are met: the unit was professionally installed and serviced by an authorized DEI deal-

er; the unit will be professionally reinstalled in the vehicle in which it was original-

ly installed by an authorized DEI dealer; and the unit is returned to DEI, shipping

prepaid with a legible copy of the bill of sale or other dated proof of purchase bear-

ing the following information: consumer's name, telephone number and address; the

authorized dealers name, telephone number and address; complete product descrip-

tion, including accessories; the year, make and model of the vehicle; vehicle license

number and vehicle identification number. All components other than the unit,

including without limitation the siren, the remote transmitters and the associated

sensors and accessories, carry a one-year warranty from the date of purchase of the

same. This warranty is non-transferable and is automatically void if: the original pur-

chaser has not completed the warranty card and mailed it within ten (10) days of the

date of purchase to the address listed on the card; the unit's date code or serial num-

ber is defaced, missing or altered; the unit has been modified or used in a manner

contrary to its intended purpose; the unit has been damaged by accident, unreason-

able use, neglect, improper service, installation or other causes not arising out of

defects in materials or construction. The warranty does not cover damage to the unit

caused by installation or removal of the unit. DEI, in its sole discretion, will deter-

mine what constitutes excessive damage and may refuse the return of any unit with

excessive damage. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES,

INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WAR-

RANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRAN-

TY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUD-

ED; AND DEI NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO

ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS

PRODUCTS. DEI DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL

ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS.

DEI SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSI-

BLE THEFT. DEI IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VAN-

DALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND

HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITH-

OUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS WAR-

1999 Directed Electronics, Inc.

RANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR REIN-

STALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE

EVENT OF A CLAIM OR A DISPUTE INVOLVING DEI OR ITS SUBSIDIARY, THE PROP-

ER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFOR-

NIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE

DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DEI SHALL BE

STRICTLY LIMITED TO THE AUTHORIZED DEI DEALER'S PURCHASE PRICE OF THE

UNIT. DEI SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUD-

ING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES,

DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF

ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE

MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE

CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on

how long an implied warranty will last or the exclusion or limitation of incidental or

consequential damages. This warranty gives you specific legal rights and you may also

have other rights that vary from State to State.

This product may be covered by a Guaranteed Protection Plan ("GPP"). See your

authorized DEI dealer for details of the plan or call DEI Customer Service at 1-800-

876-0800. DEI security systems, including this unit, are deterrents against possible

theft. DEI is not offering a guarantee or insurance against vandalism, damage or theft

of the automobile, its parts or contents; and hereby expressly disclaims any liability

whatsoever, including without limitation, liability for theft, damage and/or vandalism.

DEI does not and has not authorized any person or entity to create for it any other

obligation, promise, duty or obligation in connection with this security system.

Make sure you have all of the following information from your dealer:

A clear copy of the sales receipt, showing the following:

■ Date of purchase

■ Your full name and address

■ Authorized dealer's company name and address

■ Type of alarm installed

■ Year, make, model and color of the automobile

■ Automobile license number

■ Vehicle identification number

■ All security options installed on automobile

■ Installation receipts

1999 Directed Electronics, Inc.

Table of Contents

Limited Lifetime Consumer Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . i

What Is Included

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Important Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Your Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

FCC/ID Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Transmitter Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Standard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Expanded Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Using Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Multi-Level Security Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Arming While Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

High Security Disarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Disarming Without a Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Silent Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Panic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Valet

Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Remote Valet

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Nuisance Prevention Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Arming Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Disarming Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Table of Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Code-Hopping

™

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

High Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Owner Recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Rapid Resume Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Power Saver Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Programming Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Installation Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Vehicle Recovery System (VRS

) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Arming the VRS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

VRS

Triggered Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Disarming the VRS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Glossary Of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Security & Convenience Expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Quick Reference Guide (Removable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

1999 Directed Electronics, Inc.

Standard Configuration

1999 Directed Electronics, Inc.

What is Included

■ 3-Channel Receiver

■ A pair of two-button transmitters

■ A Stinger

Doubleguard

dual-output shock sensor (on-board

the control module)

■ The Revenger

Soft Chirp

six-tone programmable siren

■ The red status LED indicator light

■ A push-button Valet

switch

■ Your warranty card

■ Failsafe

Starter Kill ready circuitry (may require additional

labor)

Important Information

Congratulations on the purchase of your state-of-the-art vehicle

security system. This system has been designed to provide years of

trouble-free operation. Due to the complexity of this system, it

must be installed by an authorized dealer only. Installation of this

product by anyone other than an authorized dealer voids the war-

ranty. All dealers are provided with a preprinted dealer certificate

to verify that they are authorized.

This owner’s guide should help you to get the most out of your sys-

tem. Please take the time to read it prior to using the system.

1999 Directed Electronics, Inc.

The system requires no specific maintenance. Your remote control

is powered by a miniature 12V battery, type GP23A, that will last

approximately one year under normal use. When the battery weak-

ens, operating range will be reduced and the LED on the remote

will dim.

Your warranty card must be returned and the bar code serial num-

ber must not be removed. If the warranty card is not returned, you

do not have a warranty. It is also necessary to keep your proof of

purchase, which reflects that the product was installed by an au-

thorized dealer. Make sure that you receive the warranty card from

your dealer.

This device complies with Part 15 of FCC rules. Operation is sub-

ject to the following two conditions: (1) This device may not cause

harmful interference, and (2) This device must accept any interfer-

ence received, including interference that may cause undesired

operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to oper-

ate this device.

FCC/ID Notice

Your Warranty

System Maintenance

1999 Directed Electronics, Inc.

Transmitter Functions

The receiver uses a computer-based Learn Routine to learn the

transmitter buttons. This makes it possible to assign any transmit-

ter button to any receiver function. The transmitter initially comes

programmed with Standard Configuration, but may also be cus-

tomized by an authorized dealer. The buttons in all of the instruc-

tions in this manual correspond to a Standard Configuration trans-

mitter.

Button

The arming/disarming/panic functions are controlled by .

Button

Silent Mode

™

and an optional auxiliary function are controlled by

. (Silent Mode works by pressing for less than one second

before arming or disarming the system. An optional auxiliary func-

tion, such as trunk release, can be controlled by pressing for

1.5 seconds.)

The auxiliary output controls _____________________________.

and Buttons

An optional auxiliary convenience or expansion function that you

have added to your system can be activated by pressing and

simultaneously.

The auxiliary output controls _____________________________.

Standard Configuration

1999 Directed Electronics, Inc.

Your system has an expanded configuration that can be utilized

when upgrading to the four-button remote. In the expanded con-

figuration, your system will operate similarly to many factory key-

less entry systems that use separate remote transmitter buttons

for the arm, disarm, panic and auxiliary output functions. Multi-

Level Security Arming is also possible in the expanded configura-

tion. Contact your dealer for details.

Using Your System

The button numbers used in the descriptions correspond to the

standard configuration. Remember, this is not the only way your

transmitter may be set up. It can be custom configured to meet

your needs.

You can activate, or arm, the system by pressing of your

transmitter for one second. When the system arms, you will hear a

short siren sound, or chirp, and see the parking lights flash once.

If the vehicle’s power door locks have been connected to the sys-

tem, the doors will lock.

While the system is armed, the status LED will flash approximate-

ly once per second, showing that the system is actively protecting

Arming

Expanded Configuration

1999 Directed Electronics, Inc.

your vehicle. If you hear a second chirp after arming, and see the

status LED flashing in groups, refer to the Diagnostics section of

this guide. This extra chirp is called Bypass Notification.

The system also can be programmed to arm itself automatically

(called passive arming). If the system is programmed for passive

arming, it will automatically arm 30 seconds after the ignition is

turned off and the system "sees" you leave the vehicle by opening

and closing a door. Whenever the system is in its 30-second pas-

sive-arming countdown, the status LED will flash twice as fast as

it does when the system is armed. The siren will chirp one time 20

seconds after the last door has been closed. The system is not

actually armed at that point. The system arms and the doors lock

(if connected and programmed for passive locking) at the 30 sec-

ond mark, but the siren will not chirp. The early chirp provides you

with a 10-second warning prior to arming.

NOTE: If any protected entry point (such as a door or a switch-protected

trunk or hood) is open, the system will not passively arm (unless forced

passive arming is programmed on.) See Programming Options section of

this guide. Additionally, each time a sensor is triggered during the arm-

ing countdown, the 30-second countdown starts over.

When armed, your vehicle is protected as follows:

■ Light impacts will trigger the Warn Away

signal. When trig-

gered, the siren will chirp and the parking lights will flash for

a few seconds.

■ Heavy impacts will trigger the system. The triggered sequence is

between 1-180 seconds of constant siren and flashing parking

lights.

1999 Directed Electronics, Inc.

■ If a door is opened, the system will immediately start chirp-

ing the siren and flashing the parking lights. Three seconds

later, the siren output changes to a continuous blast. This

progressive response gives you time to disarm the system

with your transmitter if you inadvertently open the door

while the system is armed, while still providing an instant

response (even if the door is immediately closed).

■ Turning on the ignition key will trip the same two-stage

response as opening a door.

■ The optional starter kill prevents the vehicle’s starter from

cranking.

Multi-Level Security is a feature that is only available when using

an optional four-button remote with the Expanded Configuration.

(See Transmitter Functions section.) Multi-Level Security Arming

allows you to select which of the security system's inputs or sen-

sors will be active and which will be bypassed at the time that the

system is armed. (See Table of Zones section.) Pressing the arm

button (only on an Expanded Configuration four-button transmit-

ter) again within five seconds of arming the security system will

activate the Multi-Level Security Arming feature. Each time the

arm button is pressed again, a different security level is selected.

The different security levels can be selected as follows:

■ Pressing the arm button one time: The siren chirps once. The

system is armed.

Multi-Level Security Arming

1999 Directed Electronics, Inc.

■ Pressing the arm button a second time within five seconds:

The siren chirps twice followed by a long chirp. Zone Two is

now bypassed.

■ Pressing the arm button a third time within five seconds: The

siren chirps three times followed by a long chirp. Zone Four

is now bypassed.

■ Pressing the arm button a fourth time within five seconds:

The siren chirps four times followed by a long chirp. Zones

Two and Four are now bypassed.

■ Pressing the arm button a fifth time within five seconds: The

siren chirps five times followed by a long chirp. All input

zones, except the ignition, are now bypassed.

NOTE: Multi-Level Security Arming only applies to a single arming cycle.

Once the system is disarmed and then re-armed, all the zones will be

active again.

Your system can be armed while driving the vehicle! Simply press

on your transmitter for 1.5 seconds while the vehicle is run-

ning, or the ignition is on. The system will chirp once and then

once more to indicate that the ignition is on. The system will not

respond to any input except the door triggers and the starter kill

relay (if installed) will not be activated. The system will disarm

automatically when the ignition is turned off. The siren will chirp

twice and the LED will stop flashing.

NOTE: If programmed for the optional Vehicle Recovery System (VRS)

feature, arming with the transmitter will arm the VRS feature. (See VRS

section of this guide.)

Arming While Driving

1999 Directed Electronics, Inc.

To disarm the system, press . You will hear two chirps, and the

parking lights will flash twice. If the power locks are connected to

the system, the doors will unlock. If the siren chirps either four or

five times when disarming, refer to the Diagnostics section of this

guide. This is called Tamper Alert.

This system proudly offers High Security Disarm. High Security

Disarm is a feature that makes it possible to silence and reset the

system when it is triggering without disarming the system. If the

system is triggered, and the siren has been sounding for longer

than six seconds, pressing on the transmitter will stop the

trigger and return the unit to the armed state. The system will not

disarm, but rather reset. This prevents you from disabling the sys-

tem should you wish to disarm it without visually checking the

vehicle. Pressing the disarm button again, after resetting the sys-

tem, will disarm the system. Pressing during the first six sec-

onds of the triggered sequence will disarm the system immediate-

ly. The six second timer is provided for your convenience, in case

you accidentally trigger the system.

This feature allows you to disarm the system without the transmit-

ter should it be lost, damaged or disabled. In order to disarm

Disarming Without a Transmitter

High Security Disarm

Disarming

1999 Directed Electronics, Inc.

without a transmitter, you must have the vehicle’s ignition key

and know where the Valet

switch is located. Be sure to check with

the installer for the location of the Valet switch.

To disarm the security system,

turn the ignition to the "on"

position. Press the Valet switch

the selected number of times (1-

5 times) within 15 seconds. The

system should now disarm. If it

does not, you may have waited

too long; turn the ignition off

and on and try again.

LOCATION OF VALET SWITCH______________________________

IMPORTANT! The unit can be programmed to respond to 1-5 pulses of

the Valet

switch for the disarm function. Be sure to check with the

installer for the desired programming.

To temporarily turn off the arm or disarm chirps, use Silent Mode

™

Simply press briefly before arming or disarming, and the con-

firmation chirp(s) will be eliminated for that one operation only.

If you want the arm/disarm chirps turned off permanently, your

dealer can do this for you.

NOTE: The Warn Away

response to lighter impacts is bypassed if the sys-

tem is armed using Silent Mode. This ensures that no chirps will be emit-

ted by the siren in an area you want chirp-free. The system is still fully

capable of triggering. Only the Warn Away

response is bypassed.

Silent Mode

DRW-35

1999 Directed Electronics, Inc.

If you are threatened in or near your vehicle, you can attract

attention by triggering the system with your transmitter! Just

press for 1.5 seconds, and you will enter Panic Mode. The

siren will sound and the parking lights will flash for the pro-

grammed siren duration. To stop Panic Mode at any time, press

on the remote transmitter again.

You can prevent your security system from automatically arming

and triggering by using Valet

Mode. This is very useful when

washing the vehicle or having it serviced. In Valet Mode, the secu-

rity system will not arm, even with the remote transmitter, but all

convenience functions (door locks, trunk release, etc.) will con-

tinue to work normally.

To enter or exit Valet

Mode with the Valet switch:

1. Turn the ignition on.

2. Turn the ignition off.

3. Press and release the Valet

switch within 10 seconds.

The status LED will light solidly if you are entering Valet Mode, and

it will go out if you are exiting Valet Mode.

DRW-35

Valet

Mode

Panic Mode

1999 Directed Electronics, Inc.

The operations described in this section refer to transmitter but-

tons. Remember, the buttons used in all the instructions in this

guide correspond to a Standard Configuration transmitter. This

may not be how your transmitter is set up.

1. Open any vehicle door.

2. Press .

3. Press .

4. Press again.

The status LED will light solid if you are entering Valet Mode, or

will go out if you are exiting Valet Mode.

Your system has DEI

’s Nuisance Prevention

Circuitry (NPC

™

). It

prevents annoying repetitive trigger sequences due to faulty door

pin switches or environmental conditions such as thunder, jack-

hammers, airport noise, etc. Here’s how it works:

The alarm triggers three times. Each time, the same sensor or

switch is triggering the alarm. The three triggers are within 60

minutes of each other. NPC

™

will interpret this pattern of triggers

as false alarms. After the third trigger, NPC

™

ignores, or bypasses,

that sensor or switch (along with any other sensors or switches

sharing the same zone) for 60 minutes.

Nuisance Prevention

Circuitry

Remote Valet

1999 Directed Electronics, Inc.

If the bypassed sensor tries to trigger the system while it is being

bypassed, the 60-minute bypass period will start over. This ensures

that a sensor that continually triggers will remain bypassed.

Doors are covered by NPC differently: If the alarm is triggered by

an open door for three full cycles, the doors will be bypassed until

the trigger ceases.

NOTE: Arming and disarming the system does not reset this function!

The only ways to reset a bypassed zone are for it to not trigger for 60

minutes, or to turn on the ignition. If testing your system, it is

important to remember that the NPC programming can cause zones to be

bypassed and appear to stop working. If five chirps are heard when dis-

arming, NPC

™

has been engaged. If you wish to clear the NPC

™

memory, turn the ignition key on.

NPC

™

is programmable. See "Programming Options" section of this

guide.

Diagnostics

The microprocessor at the heart of your security system is con-

stantly monitoring all of the switches and sensors that are con-

nected to it. It detects any faulty switches and sensors and pre-

vents them from disabling the entire system. The microprocessor

will also record and report any triggers that occurred during your

absence.

1999 Directed Electronics, Inc.

If the system is armed while an input is active (door open, sensor

triggering, etc.) the unit will chirp once when arming and then

one more time a few seconds later. This is called Bypass

Notification.

NOTE: Bypass Notification will not occur when using Silent Mode

™

or if

chirps have been programmed OFF.

The security system will ignore the input that was active when the

system was armed, until the input goes away. Three seconds later

the system will monitor that input normally. For example, if your

vehicle has interior light exit delay, and you arm the system

before the interior light goes out, you may hear Bypass

Notification chirps. Once the light shuts off, however, the doors

are monitored normally.

Extra disarm chirps are the Tamper Alert. If four chirps are heard

when disarming, the system was triggered in your absence. If five

chirps are heard, a zone was triggered so many times that Nui-

sance Prevention

Circuitry has bypassed that zone. In either case,

the status LED will indicate which zone was involved (see Table of

Zones section). The system will retain this information in its mem-

ory, and continue to chirp four or five times each time it is dis-

armed, until the next time the ignition key is turned on.

Disarming Diagnostics

Arming Diagnostics

1999 Directed Electronics, Inc.

The zone number is the number of LED flashes used by the system

to identify a specific input. The standard input assignments are

listed below, along with spaces to write in any optional sensors or

switches you have had installed.

ZONE

(Number of DEALER-INSTALLED

LED Flashes) DESCRIPTION OPTIONS

Instant trigger - often used

for hood/trunk pinswitches

2 Instant trigger - a heavier impact

detected by the Double Guard

Shock Sensor

3 Door switch trigger

4 Instant trigger - for optional

sensors

5 Ignition trigger

If the Warn Away

response is triggered, the LED will not report it.

NOTE: Your system stores the last two triggered zones in memory. If your

system has been triggered but the LED has been reset by turning on the

ignition, your dealer can still recall the last two zones that were trig-

gered. Contact your dealer for details.

Table of Zones

Page is loading ...

Python 650ESP User manual

Brand: Python

Model: 650ESP

Category: Car alarm

Type: User manual

This manual is also suitable for

Download PDF

report

Python 650ESP User manual

This manual is also suitable for

Python 650ESP User manual

Related papers

Other documents