Bose KR-797 User manual

Bose
Brand
Bose
Model
KR-797
Category
Cassette players
Type
User manual

This manual is also suitable for

B60-3069-00 CS (K, P, Y)
98/12 11 10 9 8 7 6 5 4 3 2 1 97/12 11 10 9 8 7 6 5 4 3 2 1
AUDIO VIDEO SURROUND RECEIVER
KR-897
KR-797
INSTRUCTION MANUAL
KENWOOD CORPORATION
This manual contains instructions for two models. Model availability and features
(functions) may differ depending on country and sales area.
Model KR-897 is not available in except for U.S.A. and Canada.
MC
07.6.11, 5:05 PM1
KR-897/KR-797 (En)
2
Units are designed for operation as follows.
Europe and U.K. .............................................. AC 230 V only
China and Russia ............................................ AC 220 V only
*Other countries..................... AC 110-120/220-240 V switchable
U.S.A. and Canada ........................................... AC120 V only
Australia ....................................................... AC 240 V only
WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
FM indoor antenna (1)
Remote control unit (1)
AC voltage selector switch
Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage.
If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay.
Only the consignee (the person or company receiving the unit) can file a claim against the carrier for shipping damage. We recommend that you retain the
original carton and packing materials for use should you transport or ship the unit in the future.
Unpacking
Before applying power
Safety precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Note:
Our warranty does not cover damage caused by excessive line voltage
due to improper setting of the AC voltage selector switch.
Before applying power
Accessories
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS IN-
TENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN
THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF
ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO
THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE APPLIANCE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALI-
FIED SERVICE PERSONNEL.
*AC voltage selection
The AC voltage selector switch on the rear panel is set to the voltage
that prevails in the area to which the unit is shipped. Before connecting
the power cord to your AC outlet, make sure that the setting position
of this switch matches your line voltage. If not, it must be set to your
voltage in accordance with the following direction.
Move switch lever to match your line voltage
with a small screwdriver or other pointed tool.
REC OUT
PLAY IN
VIDEO 1
/TAPE 1
PLAY IN
TAPE 2
MONITOR
VIDEO 2
SUBWOOFER
PRE OUT
PLAY
IN
+
−
FRONT SPEAKERS
( 8−16Ω)
SURROUND
SPEAKERS
( 4−8Ω)
CENTER
SPEAKER
( 8−16Ω)
+
−
SYSTEM
CONTROL
SWITCHED
AC 110-120V AC 220-240V
50/60Hz
FM
75Ω
GND
AM
ANTENNA
CD
PHONO
L
R
R
L
R
L
R
L
C
AUDIO
FM
300Ω
REC OUT
DE−
EMPHASIS
CHANNEL
SPACE
50μs
AM 9kHz
FM 50kHz
75μs
AM 10kHz
FM 100kHz
ADAPTOR
L
R
L
R
OUT IN
ƒ
AC 220-
240V
AC 110-
120V
AC 220-
240V
AC 110-
120V
3 Caution : Read this section carefully to ensure safe operation.
3 Caution : Read this section carefully to ensure safe operation.
Batteries (R6/AA) (2)
AM loop antenna (1)
Loop antenna stand (1)
Shorting pins (2)
(KR-797 only)
07.6.11, 5:05 PM2
KR-897/KR-797 (En)
3
The surround system reproduces video software programs carrying the mark with similar acoustic effects to movie
theaters.
The DOLBY PRO LOGIC mode controls the audio signals of the Front Left/Right, Center and Rear surround channels using the built-in
directivity enhancer circuit to reproduce the feeling of sound motions very realistically.
The DOLBY 3 STEREO mode can reproduce the motions of sound even when only the front and center speakers are used, by providing proper
acoustic position using the directivity enhancer circuit.
The SRS (Sound Retrieval System) is an innovative system simulating a 3-dimensional sound space, which features clearly improved
feelings of depth, sound field extension and acoustic image positioning as well as a widened listening area.
Special features
DOLBY PRO LOGIC & DOLBY 3 STEREO
SRS 3D Stereo
Contents
Caution : Read the pages marked 3
carefully to
ensure safe operation.
Before applying power ............................................................................................................................................................................................. 2
3
Before applying power......................................................................................................................................... 2
3
Safety precautions ............................................................................................................................................... 2
Special features ......................................................................................................................................................................................................... 3
System connection..................................................................................................................................................................................................... 4
Connections of Audio and Video components (KR-897) ...................................................................................... 4
Connections of Audio and Video components (KR-797) ...................................................................................... 5
About the system control connections .................................................................................................................6
Connection of speakers (KR-897) ........................................................................................................................ 7
Connection of speakers (KR-797) ........................................................................................................................ 8
Connection of antenna......................................................................................................................................... 9
FM DE-EMPHASIS / CHANNEL SPACE switch
..................................................................................................
10
Controls and indicators ........................................................................................................................................................................................... 11
Operation of remote control unit ........................................................................................................................................................................... 12
Playing music ............................................................................................................................................................................................................ 14
Sound adjustment functions .................................................................................................................................................................................. 15
Recordin ..................................................................................................................................................................................................................... 18
Broadcast receptiong .............................................................................................................................................................................................. 19
Receiving broadcast stations ............................................................................................................................ 19
Receiving radio stations by specifying its frequency......................................................................................... 20
Storing radio stations in memory (Station preset) ............................................................................................. 21
Receiving a preset station ................................................................................................................................. 21
Receiving all preset stations in order (P. CALL) .................................................................................................. 21
Presence play ........................................................................................................................................................................................................... 23
Adjustments for surround play .......................................................................................................................... 24
Surround play ..................................................................................................................................................... 26
SRS 3D Stereo (Sound Retrieval System) ..........................................................................................................27
In case of difficulty .................................................................................................................................................................................................. 28
3 Specifications ........................................................................................................................................................................................................... 30
07.6.11, 5:05 PM3
KR-897/KR-797 (En)
4
PRE OUT
CENTER
L
R
SURROUND
FRONT
FRONT
REC OUT
PLAY IN
VIDEO 1
/TAPE 1
PLAY IN
TAPE 2
MONITOR
VIDEO 2
SUBWOOFER
PRE OUT
PLAY
IN
+
−
FRONT SPEAKERS
( 8−16Ω)
SWITCHED
FM
75Ω
GND
AM
CD
PHONO
L
R
R
L
R
L
AUDIO
FM
300Ω
REC OUT
SYSTEM
CONTROL
ANTENNA
PGM FILE
( )
ƒ
System connection
Make connection as shown below.
When connecting the related system components, refer
also to the instruction manuals of the related compo-
nents.
3 Do not plug in the power lead until all connections are
completed.
Connections of Audio and Video components (KR-897)
To wall
AC outlet
Turntable
Malfunction of microcomputer
If operation is not possible or erroneous display appears even
though all connections have been made properly, reset the micro-
computer referring to “In case of difficulty”. •
Video deck 2 or DVD/LD player
IN
OUT
*
2
Do not connect system control cord to the cassette
deck connected to the TAPE 2 MONITOR jacks.
*
1
The system control cord should be connected when a
KENWOOD audio component system is connected.
*
3
The KX-W797 and KM-897 are not marketed in other
areas than the USA and Canada.
Audio OUT
REC
IN
PLAY
OUT
Multipul CD player
DP-R797
÷ Do not connect up a power source which is
larger than that indicated on the socket at the
rear of the unit.
System control cord
Audio
Cassette deck 1, MD recorder
or VCR 1
*
1
System
control cord
Cassette deck
KX-W597/KX-W797*
3
Power amplifier
KM-897*
3
*
2
Cassette deck 2
07.6.11, 5:05 PM4
KR-897/KR-797 (En)
5
L
R
REC OUT
PLAY IN
VIDEO 1
/TAPE 1
PLAY IN
TAPE 2
MONITOR
VIDEO 2
SUBWOOFER
PRE OUT
PLAY
IN
+
−
FRONT SPEAKERS
( 8−16Ω)
SWITCHED
FM
75Ω
GND
AM
CD
PHONO
L
R
R
L
R
L
AUDIO
FM
300Ω
REC OUT
SYSTEM
CONTROL
ANTENNA
SURROUND
SPEAKERS
( 4−8Ω)
CENTER
SPEAKER
( 8−16Ω)
+
−
R
L C
ADAPTOR
L
R
OUT IN
PGM FILE
( )
ƒ
Make connection as shown below.
When connecting the related system components, refer
also to the instruction manuals of the related compo-
nents.
3 Do not plug in the power lead until all connections are
completed.
Connections of Audio and Video components (KR-797)
To wall
AC outlet
Turntable
Malfunction of microcomputer
If operation is not possible or erroneous display appears even
though all connections have been made properly, reset the micro-
computer referring to “In case of difficulty”. •
Multipul CD player
DP-R797
*
1
System
control cord
OUTIN
REC
IN
PLAY
OUT
Audio OUT
IN
OUT
Audio
Video deck 1, cassette deck 1
or MD recorder
System control cord
Graphic
equalizer
KE-597
cassette deck
KX-W597/KX-W797*
1
Caution regarding placement
(Except for U.S.A. and Canada)
To maintain proper ventilation, be sure to leave a space around the
unit (from the largest outer dimensions including projections)
equal to, or greater than, shown below.
Left and right panels : 10 cm
Rear panel : 10 cm
Top panel : 50 cm
*
3
The KX-W797 and KM-897 are not marketed in other
areas than the USA and Canada.
*
2
Do not connect system control cord to the cassette
deck connected to the TAPE 2 MONITOR jacks.
*
1
The system control cord should be connected when a
KENWOOD audio component system is connected.
System connection
Video deck 2 or DVD/LD player
÷ Do not connect up a
power source which is
larger than that indi-
cated on the socket at
the rear of the unit.
*
2
Cassette deck 2
07.6.11, 5:05 PM5
KR-897/KR-797 (En)
6
Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of convenient
system control operations.
There are two KENWOOD system control modes. Make connections according to the groups of terminal symbols shown below.
ƒ Mode: lets you combine F, f, and ƒ terminals
Mode: for terminals only
This unit is compatible with both [XS8] and [SL16] modes. It comes from the factory set to the [SL16] mode. To switch to the [XS8]
mode, follow the instructions in “SWITCHING BETWEEN [XS8] AND [SL16]” below.
EXAMPLE: [SL16] mode connections
The underlined portion represents the setting of the system
control mode.
1. [SL16] equipment cannot be combined with [XR], [XS], and [XS8] equipment for system operations. If your
equipment consists of this kind of combination, please do not connect any system control cords. Even
without system control cords, normal operations can be carried out without affecting performance.
2. Do not connect system control cords to any components other than those specified by KENWOOD. It may
cause a malfunction and damage your equipment.
3. Be sure the system control plugs are inserted all the way in to the system control terminals.
1. Connect all cords firmly. If connections are loose, there could be loss of sound or noise produced.
2. When plugging and unplugging connection cords, be sure to first remove the power cord from the AC outlet. Plugging / unplugging connection
cords without removal of the power cord can cause malfunctions or damage to the unit.
3. If the system control cords or audio cords are not connected properly, the remote control or automatic operation between system components
will not work properly.
Notes
Notes
÷ Some CD players and cassette decks are not compatible with the [SL16] system control mode. Be sure to use the [XS8] system control mode when
making system connections with equipment that is not [SL16] compatible.
÷ Some MD players are not system control compatible. You cannot make system control connections to this kind of equipment.
[SL16] [XS8]
[SL16]
[SL16] [XS] [XS8] [XR]
[SL16] [XS] [XS8]
Turntable
Turntable
System
control
cord
Turntable
MD Recorder
System
control
cord
LD Player
Cassette Deck
About the system control connections
ABOUT THE SYSTEM CONTROL OPERATIONS
Remote Control (possible when the system control mode
matches)
Lets you operate source components with the system remote
supplied with this unit.
Automatic Operation (Except [XR] equipment)
When you start playback from a source component, the input
selector on this unit switches to that component automatically.
(Except TAPE 2)
Synchronized Recording (Except [XR] equipment)
Lets you synchronize recording with the start of playback when
recording from CD or MD.
SWITCHING BETWEEN [XS8] AND [SL16]
The system control mode can be switched over easily with the
following operation.
1 Unplug the AC power cord from the wall outlet.
2 Set the SYSTEM CONTROL switch on the rear panel to the desired
position.
÷ This operation does not affect the items stored in memory.
( )
SYSTEM
CONTROL
ƒ
Note
Note
EXAMPLE: [XS8] mode connections
The underlined portion represents the setting of the system
control mode.
Multiple
CD Player
Receiver
Turntable
MD Recorder
LD Player
Cassette Deck
Multiple
CD Player
Receiver
[SL16] [XS8]
[SL16]
[SL16] [XS] [XS8] [XR]
[SL16] [XS] [XS8]
Notes
Notes
07.6.11, 5:06 PM6
KR-897/KR-797 (En)
7
Connection of speakers (KR-897)
R
L
·ª ª ·
÷ Never short-circuit the + and - speaker cords. For the symptom and remedy when a speaker cord is shorted. •
÷ If the left and right speakers are connected inversely or if the speaker cords are connected with reversed polarity, the sound becomes unnatural with
ambiguous acoustic image positioning. Be sure to connect the speakers and speaker cords correctly.
÷ Connect a sub woofer if you want to enhance the bass sound. The connected sub-woofer should be a power sub-woofer with a built-in amp.
*
1
Power amplifier
KM-897
ª
·
·ªª· ª·ª·
2 Insert cord.
1 Push lever.
3 Return lever.
*
1
For the operation of the
power amplifier (KM-897),
refer to the instruction
manual of the power am-
plifier (KM-897).
Speaker system A
(8Ω ~ 16Ω)
* Connect the speakers for use in
surround play to speaker sys-
tem A.
Speaker system B does not out-
put sound during surround play.
Powerd
sub-woofer
Center speaker
(8Ω ~ 16Ω)
R L
R L
Speaker system B
(8Ω ~ 16Ω)
Surround speakers
(4Ω ~ 8Ω)
The speakers connected to the KR-897 and
KM-897 reproduce sound as described below.
When surround play is used: Speakers used for reproduction
KR-897 SPEAKERS key: ON : Speaker system A/Sub-woofer
KM-897 Key: – SURROUND : Center speaker/Surround speakers
Stereo play using the KR-897: Speakers used for reproduction
KR-897 SPEAKERS key: ON : Speaker system A/Sub-woofer
KM-897 POWER key: – OFF :
Stereo play using the KM-897: Speakers used for reproduction
KR-897 SPEAKERS key: OFF :
KM-897 Key: - STEREO : Speaker system B
HEADPHONES play using only: Speakers used for reproduction
KR-897 SPEAKERS key: OFF :
KM-897 POWER key: – OFF :
÷ For the installation and adjustment of speakers for surround play £
07.6.11, 5:06 PM7
KR-897/KR-797 (En)
8
L
R
REC OUT
PLAY IN
VIDEO 1
/TAPE 1
PLAY IN
TAPE 2
MONITOR
VIDEO 2
SUBWOOFER
PRE OUT
PLAY
IN
+
−
FRONT SPEAKERS
( 8−16Ω)
SWITCHED
FM
75Ω
GND
AM
CD
PHONO
L
R
R
L
R
L
AUDIO
FM
300Ω
REC OUT
SYSTEM
CONTROL
ANTENNA
SURROUND
SPEAKERS
( 4−8Ω)
CENTER
SPEAKER
( 8−16Ω)
+
−
R
L C
ADAPTOR
L
R
OUT IN
( )
ƒ
Connection of speakers (KR-797)
Speaker system
(8Ω ~ 16Ω)
R
L
Center speaker
(8Ω ~ 16Ω)
Powerd
sub-woofer
·ª ª ·
ª·
ª
Surround speakers
(4Ω ~ 8Ω)
RL
÷ Never short-circuit the + and - speaker cords. For the symptom and remedy when a speaker cord is shorted: •
÷ If the left and right speakers are connected inversely or if the speaker cords are connected with reversed polarity, the sound becomes unnatural with
ambiguous acoustic image positioning. Be sure to connect the speakers and speaker cords correctly.
÷ Connect a sub woofer if you want to enhance the bass sound. The connected sub-woofer should be a power sub-woofer with a built-in amp.
·
·
ª
2 Insert cord.
1 Push lever.
3 Return lever.
ADAPTOR jacks (KR-797)
When an adaptor-type component such as a graphic equalizer is
connected, unplug the shorting pins from the ADAPTOR jacks and
connect the component to these jacks.
÷ When the ADAPTOR jacks are not used, be sure to plug the shorting
pins into jacks. Otherwise, the sound will not be produced.
÷ When the ADAPTOR jacks are used, retain the shorting pins and be
careful not to lose them.
÷ Never plug a shorting pin into other jacks than ADAPTOR jacks.
Otherwise, the unit may be damaged.
Shorting pins
L
R
ADAPTOR
L
R
OUT IN
shorting pins
07.6.11, 5:06 PM8
KR-897/KR-797 (En)
9
3 Return lever.2 Insert cord.
1 Push lever.
Connection of antenna
Connection method to each antenna terminal
AM loop antenna connection
The supplied antenna is for indoor use. Place it as far as possible from the
main system, TV set, speaker cords and power cord, and set it to a
direction which provides the best reception.
The illustration shows the KR-797.
The illustration shows the KR-797.
When using a commercially-available
T-shaped indoor antenna (300 Ω),
connect it to these terminals.
(Remove the provided indoor antenna if you
connect a T-shaped indoor antenna.)
FM outdoor antenna connection
Lead the 75 Ω coaxial cable connected to the FM outdoor antenna into
the room and connect it to the FM 75 Ω terminal.
FM indoor antenna connection
The accessory antenna is for temporary indoor use only. For stable signal
reception we recommend using an outdoor antenna. Remove the indoor
antenna if you connect one outdoors.
REC OUT
PLAY IN
VIDEO 1
/TAPE 1
PLAY IN
TAPE 2
MONITOR
VIDEO 2
PLAY
IN
+
−
FM
75Ω
GND
AM
CD
PHONO
L
R
R
L
AUDIO
FM
300Ω
REC OUT
SYSTEM
CONTROL
ANTENNA
SURROUND
SPEAKERS
( 4−8Ω)
CENTER
SPEAKER
( 8−16Ω)
+
−
R
L C
ADAPTOR
L
R
OUT IN
FM
75Ω
GND
AM
ANTENNA
FM
300Ω
SUBWOOFER
PRE OUT
R
L
ƒ
L
R
FRONT SPEAKERS
( 8−16Ω)
SWITCHED
REC OUT
PLAY IN
VIDEO 1
/TAPE 1
PLAY IN
TAPE 2
MONITOR
VIDEO 2
PLAY
IN
+
−
FRONT SPEAKERS
( 8−16Ω)
SWITCHED
FM
75Ω
GND
AM
CD
PHONO
L
R
R
L
AUDIO
FM
300Ω
REC OUT
SYSTEM
CONTROL
ANTENNA
SURROUND
SPEAKERS
( 4−8Ω)
CENTER
SPEAKER
( 8−16Ω)
+
−
R
L C
ADAPTOR
L
R
OUT IN
FM
75Ω
10mm 10mm
GND
AM
ANTENNA
FM
300Ω
SUBWOOFER
PRE OUT
R
L
ƒ
L
R
Pull out while rotating.
The illustration shows the KR-797.
07.6.11, 5:06 PM9
KR-897/KR-797 (En)
10
÷ When changing the setting of the FM DE-EMPHASIS / CHANNEL
SPACE switch, first disconnect the power cord of the amplifier, then
reset the channel space switch, connect the power cord again, and turn
the power on.
CHANNEL
SPACE freq.
FM DE-
EMPHASIS
75 µs
1
U.S.A., Canada,
Hawaii, South
American countries
Other countries 50 µs
2
FM: 50kHz
AM: 9kHz
FM: 100kHz
AM: 10kHz
Area
FM DE-EMPHASIS / CHANNEL SPACE switch
(Except for U.S.A. and Canada)
The FM DE-EMPHASIS / CHANNEL SPACE switch on the rear panel is
set to the correct setting that prevails in the area to which the unit is
shipped. However, if the FM DE-EMPHASIS / CHANNEL SPACE setting
is not matched to the area where the unit is to be used; for instance,
when you moved from area 1 to area 2 or vice versa, desired reception
of AM / FM broadcasts is not expected. In this case, change the FM DE-
EMPHASIS / CHANNEL SPACE setting in accordance with the area
corresponding to the table. The FM DE-EMPHASIS is switched over at
the same time.
REC OUT
PLAY IN
VIDEO 1
/TAPE 1
PLAY IN
TAPE 2
MONITOR
VIDEO 2
SUB WOOFER
PRE OUT
PLAY
IN
+
−
FRONT SPEAKERS
( 8−16Ω)
REAR
SPEAKERS
( 4−8Ω)
CENTER
SPEAKERS
( 8−16Ω)
+
−
SYSTEM
CONTROL
SWITCHED
AC 110-120V AC 220-240V
50/60Hz
FM
75Ω
GND
AM
ANTENNA
CD
PHONO
L
R
R
L
R
L
R
L
C
AUDIO
FM
300Ω
REC OUT
DE−
EMPHASIS
CHANNEL
SPACE
50μs
AM 9kHz
FM 50kHz
75μs
AM 10kHz
FM 100kHz
DE−
EMPHASIS
CHANNEL
SPACE
50μs
AM 9kHz
FM 50kHz
75μs
AM 10kHz
FM 100kHz
ƒ
ADAPTOR
L
R
L
R
OUT IN
AC 220-
240V
AC 110-
120V
07.6.11, 5:06 PM10
KR-897/KR-797 (En)
11
POWER
PHONES
ON/STANDBY
INPUT SELECTOR VOLUME CONTROL
UP
DOWN
STANDBY
1234 567890
+10
SPEAKERS
SURROUND
S.DIRECT
3 STEREO
AUTO
TUNEDAM FM
M
kHz
MHz
****** **
;
12 5890
!#
43
( ™^&* ) ¡ £
AUTO DIRECT
MEMORY
PRO LOGIC
STEREO SRS 3D
N.B.
SOURCE
DIRECT
P.CALL
3 STEREO
TUNING
BAND DISPLAY
TAPE2
MONITOR
6
TAPE 2
N.B. ST.
7
@ %$
SRS
3D
AUDIO-VIDEO SURROUND RECEIVER KR-897
SPEAKERS
Controls and indicators
@AUTO key
Press to select the tuning mode from the
auto tuning and manual tuning modes.(
Press and hold the AUTO key for more than
2 seconds to switch the TAPE1 display to
another input display. $
#SPEAKERS key
Press to turn the speakers ON and OFF.
$DIRECT key )
Press when tuning a broadcast station by
entering the digits of its frequencies.
%MEMORY key ¡
Press when registering a broadcast sta-
tion in the preset memory.
^Numeric keys (1 to 0, +10)
&BAND key (
Press to switch the broadcasting band.
1POWER key
Press to switch the power ON and OFF.
2STANDBY indicator
3SRS 3D indicator
Lights when the SRS 3D system is ON.
4SPEAKERS indicator
Lights when the speakers are ON.
5STEREO key §
Press to turn the surround mode OFF.
6DOLBY PRO LOGIC key ¢
7DOLBY 3 STEREO key §
8SRS 3D key
9INPUT SELECTOR knob
Rotate to select the input source.
0VOLUME CONTROL knob
!PHONES jack
Plug headphones into this jack.
*DISPLAY key
Press to switch the displayed information
between the surround mode display and
input selector display.
Press and hold the DISPLAY key for more
than 2 seconds to switch the display bright-
ness.
(TUNING keys ( , ) (
Press to select a radio station.
)TAPE 2 MONITOR key *
Press to monitor the sound being re-
corded, etc.
¡N.B. key ^
Press to compensate for the insuffi-
ciency in the base sound.
™P.CALL keys ( , ) ¡
Press to select one of the preset sta-
tions.
£SOURCE DIRECT key ^
Press to listen to the source sound with
a higher sound quality.
About the STANDBY indicator
This unit has a STANDBY indicator, the lighting of which indicates that a small amount of current is supplied to back up the internal memory of the unit.
This status is referred to as the standby mode of the unit. In this mode, the power of the unit can be switched ON from the remote control unit.
When the unit is not to be used for a long period of time, unplug the power cord from the power outlet.
Display
AUTO tuning/AUTO
stereo reception indicator
Frequency display,
Input display,
Preset channel display,
Surround mode display
TUNED indicator
MEMORY indicator
Source Direct
indicator
3 STEREO
indicator
SURROUND
indicator
STEREO
indicator
TAPE 2 indicator
Broadcast band
indicators
N.B. circuit
indicator
07.6.11, 5:06 PM11
KR-897/KR-797 (En)
12
Operation of remote control unit
The remote control unit provided with the receiver can also control KENWOOD cassette decks, MULTIPLE CD player and MD
recorder connected to the recieiver through system control cords. For details of the controllable functions, refer to the
instruction manuals of these components.
Names of keys and their functions
SOUND key %¶
Press to adjust the tone.
LISTEN MODE key §
Press to select the type of the surround
mode.
POWER key
Press to switch ON/OFF the power of this
unit as well as the KENWOOD components
connected to it through system control cords.
Model: RC-R0505
Infrared ray system
INPUT keys
Press to select the input.
LEVEL CONTROL keys %¢
Press to adjust the tone or during setup of
the surround mode.
VOLUME CONTROL keys
Press to adjust the volume.
MUTE key
Press to mute sound temporarily.
÷ Insert two AA-size (R6 / SUM-3) batteries
as indicated by the polarity marking.
2
1
2
1
CENTER MODE key ¢
Press to select the center mode in the
DOLBY PRO LOGIC surround mode.
SETUP key %¢
Press to set up the balance or surround play.
Numeric keys
Used as the numeric keys of the input source
component being selected.
Loading batteries
The AV AUX key cannot be used
with the KR-897 and KR-797.
Note
Note
1 Remove the cover. 2 Insert batteries. 3 Close the cover.
Refer to the remote control key corre-
spondence table on the next page.
POWER
12
3
45
6
78
9
DISK SKIP
0
+10
SOUND
CENTER
MODE
A/B +100
VIDEO1
TAPE1
TUNER
CD PHONO
VIDEO2 MUTE
1
¡
7
6
AV AUX
SETUP
REMOTE CONTROL UNIT
RC-R0505
4 ¢
2
AUTO
BAND
P.CALL
MONITOR
TAPE2
VOLUME
CONTROL
LEVEL
CONTROL
LISTEN
MODE
07.6.11, 5:06 PM12
KR-897/KR-797 (En)
13
1. The supplied batteries are intended for use in operation checks. Therefore, their lives may be shorter than ordinary batteries.
2. When the remote-controllable distance gets shorter than before, replace both batteries with new ones.
3. Malfunction may occur if direct sunlight or the light of a high-frequency lighting fluorescent lamp enters the remote control light
sensor. In such a case, change the system installation position to prevent the malfunction.
Operation procedure
Notes
Notes
Select the component to be remote controlled
with one of the controlled component selection
keys.
Refer to the remote control key correspondence
table below and press the key for the desired
operation.
6
BAND
1
¡
2
TUNER
CD
7
AUTO
DISK SKIP
A/B +100
2 Controlled component
selection key
3 Operation key
4 ¢
P.CALL
A/B key
Press TAPE A or B
+100
4 , ¢
(Skip key)
1 , ¡
(Tuning keys)
Press to tune broadcast
stations.
AUTO key
Press to select the auto
tuning mode.
P.CALL keys
Recalls preset stations.
4 , ¢
(Skip key)
BAND key
Press to switch the broad-
cast band.
7
(Stop key)
DISC SKIP key
Press to select the disc to
be played.
6
(Play/pause key)
1 , ¡
(Search key)
7
(Stop key)
6
(Forward play key)
1 , ¡
(Search key)
6
(Play key)
7
(Stop key)
1 , ¡
(Search key)
™
(Reverse play key)
*
1
1
Switch ON the power of the main unit.
Approximate operating range
÷ *
1
: No remote control key is marked MD, but the
TAPE1 key can be used to control a MD player by
switching the display of the main unit from TAPE1
to MD. $
Remote
sensor
Model: RC-R0505
Infrared ray system
÷ Pressing the POWER key of the remote control unit while the STANDBY
indicator is lit turns the power ON. Press the desired key after the
power has been turned ON.
÷ When two operation keys of the remote control unit are pressed
successively, press each key securely reserving an interval of more
than 1 second for each press.
(When used with a MD)
Remote control key correspondence table (For KENWOOD component control mode)
TAPE1
TAPE1
SRS
3D
POWER
PHONES
ON/STANDBY
INPUT SELECTOR VOLUME CONTROL
UP
DOWN
STANDBY
1234567890
+10
SPEAKERS
AUTO DIRECT
MEMORY
AUDIO-VIDEO SURROUND RECEIVER KR-V797
PRO LOGIC
STEREO SRS 3D
N.B.
SOURCE
DIRECT
P.CALL
3 STEREO
TUNING
BAND DISPLAY
TAPE2
MONITOR
SPEAKER
30°
6m
30°
POWER
12
3
45
6
78
9
DISK SKIP
0
+10
SOUND
CENTER
MODE
A/B +100
VIDEO1
TAPE1
TUNER
CD PHONO
IDEO2 MUTE
1
¡
7
6
AV AUX
SETUP
REMOTE CONTROL UNIT
RC-R0505
4 ¢
2
AUTO
BAND
P.CALL
MONITOR
TAPE2
VOLUME
CONTROL
LEVEL
CONTROL
LISTENI
MODE
2
3
07.6.11, 5:06 PM13
KR-897/KR-797 (En)
14
Playing music
Adjust the volume.
1
POWER
ON/STANDBY
Turn the power ON.
Select the SPEAKERS key setting.
2
SPEAKERS
Select the input source.
3
Play the selected source.
4
The input sources are switched in the following order:
÷ The time taken till the volume level is displayed is variable depending
on the current operating condition.
÷ Rotating the VOLUME CONTROL at a higher speed increases the
amount of volume change (AI VOLUME function).
÷ The sound of input source cannot be listened to while TAPE 2
MONITOR is ON.
1 TUNER (frequency display)
2 PHONO
3 TAPE1 (MD or VIDEO1)*
1
4 CD
5 VIDEO2
*
1
: Switching the TAPE1 display to MD or VIDEO1 display
When a KENWOOD MD recorder is connected in the [SL 16] system
control mode, the TAPE 1 input should be switched to the MD input
using the following procedure.
1Select TAPE1 with the INPUT SELECTOR.
2Press and hold the AUTO key for more than 2
seconds to select MD.
Volume level is displayed.
When the SPEAKERS indicator is ON:
The speakers connected to the SPEAKERS terminals on the rear
panel output sound.
When the SPEAKERS indicator is OFF:
The speakers do not output sound. Use this setting when listening
through headphones.
The SPEAKERS indicator should light up.
3 VIDEO12 MD1 TAPE1
5
VOLUME CONTROL
DOWN
UP
To decrease
volume
To increase
volume
INPUT SELECTOR
CD
The selected source is
displayed.
Note
Note
: Keys or controls to be used in this operation
VOL-68 dB
STANDBY
SRS
3D
SPEAKERS
POWER
PHONES
ON/STANDBY
INPUT SELECTOR VOLUME CONTROL
UP
DOWN
1234567890
+10
AUTO DIRECT
MEMORY
AUDIO-VIDEO SURROUND RECEIVER KR-897
PRO LOGIC
STEREO SRS 3D
N.B.
SOURCE
DIRECT
P.CALL
3 STEREO
TUNING
BAND DIMMER
TAPE2
MONITOR
POWER
12
3
45
6
78
9
DISK SKIP
0
+10
SOUND
CENTER
MODE
A/B +100
TUNER
CD PHONO
VIDEO2 MUTE
1
¡
7
6
AV AUX
REMOTE CONTROL UNIT
RC-R0505
4 ¢
2
AUTO
BAND
P.CALL
VOLUME
CONTROL
STANDBY
SPEAKERS
SRS
3D
SPEAKERS
VIDEO1
TAPE1
SETUP
TAPE2
MONITOR
LEVEL
CONTROL
LISTEN
MODE
÷ For the operation when the power amplifier (KM-897) is connected to
the KR-897, see 7 and refer to the instruction manual of the
KM-897.
07.6.11, 5:06 PM14
KR-897/KR-797 (En)
15
Sound adjustment functions
: Keys or controls to be used in this operation
÷ If the SURROUND, 3STEREO or S.DIRECT indicators are lit, press the
STEREO key to turn them OFF.
The displayed value changes.Display when “BASS” is selected.
3 Adjust the balance.
4 Press the SETUP key to return to the
previous input selector display.
1 Ensure that the SRS 3D and S.DIRECT
indicators are not lit.
SOUND
LEVEL
CONTROL
2 Select the tone mode to be adjusted (from
BASS, MIDDLE and TREBLE).
3 Adjust the tone
To increase
level
To decrease
level
1 Ensure that the SURROUND, 3 STEREO
and S.DIRECT indicators are off.
LEVEL
CONTROL
To decrease
the right
channel sound
SETUP
Adjusting the left/right sound balance
Adjusting the tone
2 Press the SETUP key.
To decrease
the left
channel sound
POWER
PHONES
UP
DOWN
1234567890
AUTO DIRECT
MEMORY
PRO LOGIC
STEREO SRS 3D
N.B.
SOURCE
DIRECT
P.CALL
3 STEREO
TUNING
TAPE2
MONITOR
POWER
12
3
45
6
78
9
DISK SKIP
0
+10
SOUND
CENTER
MODE
A/B +100
TUNER
CD PHONO
VIDEO2
MUTE
1
¡
7
6
AV AUX
REMOTE CONTROL UNIT
RC-R0505
4 ¢
2
AUTO
BAND
P.CALL
VOLUME
CONTROL
STANDBY
SPEAKERS
SRS
3D
SPEAKERS
INPUT SELECTOR VOLUME CONTROL
+10
AUDIO-VIDEO SURROUND RECEIVER KR-897
BAND DIMMER
VIDEO1
TAPE1
SETUP
TAPE2
MONITOR
LEVEL
CONTROL
LISTEN
MODE
BASS 2
BASS -2
SURROUND
3 STEREO
S.DIRECT
÷ Adjustment of SRS (Sound Retrieval System) 3D Stereo.
The level can be adjusted between -8 and
+8 with an increment or decrement of 2
per press.
1 BASS : Mode for adjusting the low frequencies.
2 MIDDLE : Mode for adjusting the middle frequencies.
3 TREBLE : Mode for adjusting the high frequencies.
4 End of setting
Each press of the key switches the modes as follows:
(When the SRS 3D Stereo is OFF)
÷ If the S.DIRECT indicator is lit, press the S.DIRECT key to turn it off.
If the SRS 3D indicator is lit, press the SRS 3D key to turn it off.
S.DIRECT
SRS
3D
Make sure that the
light is out.
---yt- -
Position of the right speaker
Indicates the centerPosition of the left speaker
Indicates the balance setting
Make sure that the light is out.
07.6.11, 5:06 PM15
KR-897/KR-797 (En)
16
: Keys or controls to be used in this operation
÷ During Source Direct playback, the tone controls (BASS,MIDDLE and
TREBLE), balance control and N.B. are defeated.
÷ The Source Direct playback is canceled when any key associated with
the surround play is pressed.
Lights
Source Direct playback
This feature allows you to play the source signal with a high quality by
passing it only through the minimum required circuitry.
INPUT SELECTOR
SOURCE
DIRECT
2 Press the SOURCE DIRECT key.
Compensating for low frequencies (N.B.: Natural Bass circuit)
N.B. circuit is used to compensate for the low frequencies which are less
audible during low-volume listening.
N.B.
Lights
1 Choose the playback source.
3 Playback the source.
To cancel
Press the SOURCE DIRECT key again.
Goes off
POWER
PHONES
ON/STANDBY
UP
DOWN
1234567890
AUTO DIRECT
MEMORY
PRO LOGIC
STEREO SRS 3D
N.B.
SOURCE
DIRECT
P.CALL
3 STEREO
TUNING
TAPE2
MONITOR
POWER
12
3
45
6
78
9
DISK SKIP
0
+10
SOUND
CENTER
MODE
A/B +100
TUNER
CD PHONO
VIDEO2
MUTE
1
¡
7
6
AV AUX
REMOTE CONTROL UNIT
RC-R0505
4 ¢
2
AUTO
BAND
P.CALL
VOLUME
CONTROL
STANDBY
SPEAKERS
SRS
3D
SPEAKERS
INPUT SELECTOR VOLUME CONTROL
+10
AUDIO-VIDEO SURROUND RECEIVER KR-897
BAND DIMMER
VIDEO1
TAPE1
SETUP
TAPE2
MONITOR
LEVEL
CONTROL
LISTEN
MODE
S.DIRECT
CD
S.DIRECT
CD
CD
N.B.
Goes off
To cancel
Press the N.B. key again.
CD
N.B.
÷ When the S.DIRECT is selected, the N.B. control keys are not effective.
07.6.11, 5:06 PM16
KR-897/KR-797 (En)
17
: Keys or controls to be used in this operation
Make sure the light is out.
MUTE
To cancel
Press the MUTE key again.
SPEAKERS
3 Adjust the volume.
To decrease
volume
To increase
volume
VOLUME CONTROL
DOWN
UP
PHONES
1 Press the SPEAKERS key to OFF.
To listen through headphones
2 Plug headphones.
To mute sound temporarily
Remote control unit only
Blinks
POWER
PHONES
ON/STANDBY
UP
DOWN
1234567890
AUTO DIRECT
MEMORY
PRO LOGIC
STEREO SRS 3D
N.B.
SOURCE
DIRECT
P.CALL
3 STEREO
TUNING
TAPE2
MONITOR
POWER
12
3
45
6
78
9
DISK SKIP
0
+10
SOUND
CENTER
MODE
A/B +100
TUNER
CD PHONO
VIDEO2
MUTE
1
¡
7
6
AV AUX
REMOTE CONTROL UNIT
RC-R0505
4 ¢
2
AUTO
BAND
P.CALL
VOLUME
CONTROL
STANDBY
SPEAKERS
SRS
3D
SPEAKERS
INPUT SELECTOR VOLUME CONTROL
+10
AUDIO-VIDEO SURROUND RECEIVER KR-897
BAND DIMMER
VIDEO1
TAPE1
SETUP
TAPE2
MONITOR
LEVEL
CONTROL
LISTEN
MODE
STANDBY
SRS
3D
SPEAKERS
MUTE ON
÷ For the operation when the power amplifier (KM-897) is connected
to the KR-897, see 7 and refer to the instruction manual of the
KM-897.
07.6.11, 5:06 PM17
KR-897/KR-797 (En)
18
Recording
To record a music source
1 Select the source to be recorded.
Copying tape (Tape dubbing TAPE 2 = TAPE 1)
The input sources are switched in the following order:
1 TUNER (frequency display)
2 PHONO
3 TAPE1 (MD or VIDEO1)
4 CD
5 VIDEO2
INPUT SELECTOR
2 Select a source other than TAPE 1.
TUNING
BAND
DISPLAY
TAPE2
MONITOR
INPUT SELECTOR
CD
TAPE 2
Lights
÷ For copying a tape using a double cassette deck, read the instruction
manual of the double cassette deck.
Copying tape (Tape dubbing TAPE 1 = TAPE 2)
1 Select TAPE 1 with the INPUT SELECTOR control of the
main unit.
2 Play the cassette deck connected to the TAPE 1 jacks and
start recording of the cassette deck connected to the
TAPE 2 jacks.
1 Press the TAPE 2 MONITOR key.
3 Play cassette deck 2 and start recording
on cassette deck 1.
When recording sound with a recorder component of KENWOOD, synchro recording is possible by setting the INPUT SELECTOR
to select TAPE1 or MD according to the connected component.
Regarding TAPE 2 MONITOR
A cassette deck or graphic equalizer can be connected to this unit’s TAPE 2 MONITOR terminals. If you connect a graphic equalizer, turn the
TAPE 2 MONITOR key ON. If you connect a 3-head cassette deck, you can monitor the source sound, or the sound being recorded, while
recording. Pressing the TAPE 2 MONITOR key lets you compare the recorded sound and the source sound. Refer to the operating manual for
the component you connected for further details.
Preparation
÷ Switch the TAPE1 display to MD or VIDEO1 with the following
operation.
1 Select TAPE1 with the INPUT SELECTOR.
2 Press and hold the AUTO key for more than 2 seconds.
Select an input
source other than
TAPE 1.
2 Put the cassette deck in record-pause
mode.
3 Play the source and start recording.
3 VIDEO12 MD1 TAPE1
Each press switches the display.
÷ The VIDEO1 display can be switched to the display of other input by
using the procedure described in “Preparation” above.
÷ For the synchro recording with a cassette deck and/or MD recorder,
refer to the respective instruction manuals..
÷ It is not possible the VIDEO1 or MD input to TAPE1 because all of these
components should use the same INPUT SELECTOR position.
07.6.11, 5:06 PM18
KR-897/KR-797 (En)
19
Broadcast reception
1
Select the TUNER input.
INPUT SELECTOR
Select the broadcast band.
2
Select the tuning method.
3
Select a station.
4
: Keys or controls to be used in this operation
1 FM
2 AM
Each press switches the band as follows:
“AM” or “FM” indicator
1TUNER (frequency display)
2PHONO
3TAPE1 (MD or VIDEO1)*
1
4CD
5VIDEO2
The input sources are switched in the following order:
Frequency display
1 AUTO lit (auto tuning)
2 AUTO not lit (manual tuning)
Select manual tuning when noise interferes due to weak radio wave.
(The stereo broadcasting is received in monaural during manual tuning.)
÷ Usually, set the switch to AUTO (auto tuning).
Each press switches the turning method as follows:
TUNING
BAND
DISPLAY
TAPE2
MONITOR
To increase frequency
To decrease
frequency
AUTO
DIRECT
MEMORY
TUNING
BAND
DISPLAY
TAPE2
MONITOR
÷ The last frequency tuned before is displayed.
÷ *
1
: How to switch the display *$
Lights
Receiving broadcast stations
POWER
PHONES
ON/STANDBY
UP
DOWN
1234567890
AUTO DIRECT
MEMORY
PRO LOGIC
STEREO SRS 3D
N.B.
SOURCE
DIRECT
P.CALL
3 STEREO
TUNING
TAPE2
MONITOR
POWER
12
3
45
6
78
9
DISK SKIP
0
+10
SOUND
CENTER
MODE
A/B +100
TUNER
CD PHONO
VIDEO2
MUTE
1
¡
7
6
AV AUX
REMOTE CONTROL UNIT
RC-R0505
4 ¢
2
AUTO
BAND
P.CALL
VOLUME
CONTROL
STANDBY
SPEAKERS
SRS
3D
SPEAKERS
INPUT SELECTOR VOLUME CONTROL
+10
AUDIO-VIDEO SURROUND RECEIVER KR-897
BAND DIMMER
VIDEO1
TAPE1
SETUP
TAPE2
MONITOR
LEVEL
CONTROL
LISTEN
MODE
AUTO
FM
MHz
-- 89 00
.
AUTO
MHz
89 00
.
MHz
89 00
.
Frequency display
“TUNED” lights up when a
station is tuned.
AUTO
TUNEDFM
MHz
-- 89 00
.
Auto tuning : The next station found is tuned automatically.
Manual tuning : Press repeatedly or hold until a station is tuned.
÷ The same operation is also available with the
1
and
¡
keys of the
remote control unit.
07.6.11, 5:06 PM19
KR-897/KR-797 (En)
20
: Keys or controls to be used in this operation
The input sources are switched in the following order:
1TUNER (frequency display)
2PHONO
3TAPE1 (MD or VIDEO1)
4CD
5VIDEO2
Frequency display
1
Select the TUNER input.
INPUT SELECTOR
Select the broadcast band.
2
TUNING
BAND
DISPLAY
TAPE2
MONITOR
Specify the frequency.
3
12345 678
2 Enter the frequency of the desired
station.
1 FM
2 AM
Each press switches the band as follows:
“AM” or “FM” indicator
Press the numeric keys according to the frequency to be tuned as
shown below.
*AM10kHz/FM100kHz territories (U.S.A., Canada, etc.)
AM 810 kHz ............ 8, 1 ( 10 kHz space)
AM 1260 kHz ............ 1, 2, 6 ( 10 kHz space)
FM 89 MHz ............ 8, 9, ) (100 kHz space)
FM 92.5 MHz ............ 9, 2, 5 (100 kHz space)
*AM9kHz/FM50kHz territories (other countries)
AM 810 kHz ............ 8, 1, ) ( 9 kHz space)
AM 1260 kHz ............ 1, 2, 6, ) ( 9 kHz space)
FM 89 MHz ............ 8, 9, ), ) ( 50 kHz space)
FM 92.5 MHz ............ 9, 2, 5, ) ( 50 kHz space)
*FM DE-EMPHASIS/CHANNEL SPACE switch 0
Frequency indicator
“TUNED” lights up when a station is tuned.
÷ If you make a mistake, the frequency display blinks for a few seconds.
In this case, repeat step 3 from the beginning.
Receiving radio stations by specifying its frequency
Blinks
POWER
PHONES
ON/STANDBY
UP
DOWN
1234567890
AUTO DIRECT
MEMORY
PRO LOGIC
STEREO SRS 3D
N.B.
SOURCE
DIRECT
P.CALL
3 STEREO
TUNING
TAPE2
MONITOR
POWER
12
3
45
6
78
9
DISK SKIP
0
+10
SOUND
CENTER
MODE
A/B +100
TUNER
CD PHONO
VIDEO2
MUTE
1
¡
7
6
AV AUX
REMOTE CONTROL UNIT
RC-R0505
4 ¢
2
AUTO
BAND
P.CALL
VOLUME
CONTROL
STANDBY
SPEAKERS
SRS
3D
SPEAKERS
INPUT SELECTOR VOLUME CONTROL
+10
AUDIO-VIDEO SURROUND RECEIVER KR-897
BAND DIMMER
VIDEO1
TAPE1
SETUP
TAPE2
MONITOR
LEVEL
CONTROL
LISTEN
MODE
AUTO
FM
MHz
-- 89 00
.
AUTO
FM
MHz
FM
FM
.
_
AUTO
FM
MHz
-- 89 00
.
AUTO
TUNEDFM
MHz
-- 89 00
.
1 Press the DIRECT key.
AUTO
DIRECT
MEMORY
07.6.11, 5:06 PM20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Bose KR-797 User manual

Bose
Brand
Bose
Model
KR-797
Category
Cassette players
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents