AneX AG-3053 Operating instructions
- Category
- Slicers
- Type
- Operating instructions
This manual is also suitable for
5 Cleaning And Maintenance
a) The Power Plug Must Be Pulled Out From Mains Socket Before Cleaning The Parts And
Main Engine To Prevent Electric Shock.
b) Except Main Engine All Parts Maybe Cleaned In Water And Then Dried Up.
c) Any Residue Shouldn’t Be Remained In The Filter Screen So As To Ensure A Running Bal-
ance.
d) A Certain Volume Of Heat Water And Several Drops Of Food Cleaner Maybe Added In The
Water When The Mixing And Mincing Are To Be Washed. They Can Be Cleaned Through An
Idle Running By Switching On The Power Button Or Quick Cleaning Button For 10 Seconds
.Also, They Can Be In Water By A Brush.
e)The Device Should Be Stored In A Dry And Ventilated Place When They Are Not In Use.
f) Switch Off And Pull The Plug Before Change Of Accessories.
Instructions for use
Best. No... item no... Ref. No.
AG-3053
a )Overload And Idle Running Is Forbidden During Use.
b)The Milling Cup Is Only Suitable For Processing Dry Food Into
Power. Don’t Pour Any Liquid Into It. The Recommended Quantity
Of Food Put In The Cup Is 1/3 To 2/3 Of The Volume Of The Cup.
c ) Water Of Edible Oil Must Be Remained In The Filter Screen So
As To Ensure A Running Balance.
d) A Certain Volume Of Heat Water And Several Drops Of Food
Cleaner May Be Added In The Water When The Mixing And Minc-
ing Cups Are To Be Washed. They Can Be Cleaned Through An
Idle Running By Switching On The Power Button Or Quick Clean-
ing Button For 10 Seconds. Also, They Can Be Cleaned In Water
By A Brush.
e) The Device Should Be Stored In A Dry And Ventilated Place
When They Are Not In Use.
f) The Blade Is Very Sharp, At Cleaning With Replace The Agitation
Knife Hour Must Look Out.
g) If The Supply Cord Is Damaged, It Must Be Replaced By The
Manufacturer Or Its Service Agent Or A Similarly Qualified Person
In Order To Avoid A Hazard.
x
(3)Combination With Mincing Cup And Usage
a) Put The Main Engine A On The Flat Top Of A Table.
b) Amount The Mincing Cup X To The Main Engine. Press Down The Cup And Screw It Counter-
clockwise So As To Get The Cramp On The Cup Firmly Locked At The Cramping Position Of Main
Engine.
c) Cut The Meat Into Small Pieces (Get Rid Of Skins, Boned And Tendons) And But Them Into The
Mincing Cup. Put On The Cover Of Mincing Cup And Get It Pressed Tightly.
d) Press The Mincing Cup By One Hand And Switch On The Power By Another Hand To Start The
Mincing Operation.
Caution
:
FOOD
PROCESSOR
COMBINED MULTIFUNCTION
5
R
P
M
Q
A
O
Continue Work Time : Don’t Exceed 1 Minute
The Turning Of Electric Appliances Is Soon:
About 12000 Rpm.
2 Main technical parameters
1.Rated Voltage: 220-240V~
2 Rated Frequency: 50Hz
3. Rated Power: 500W
4. Protection Class II
3 Combination of juicer and method for use
1. Put The Engine A On A Table
2. Put The Juice-Residue Separating Slot Q Onto The Engine And Tighten It
Counterclockwise.
3. Amount The Filter P To The Driving Gear.
4. Put The Transparent Cover O Onto The Separating Slot Q And Then Get The
Safety Buckle Engaged In And Make The Separating Slot Q Be Firmly Fixed
With The Transparent Cover O.
5. Let The Juicer Have An Idle Operation For Five Seconds Before Putting It Into
Work Operation, Which May Prolong The Service Life Of This Product.
6. Get Rid Of Fruit Skin And Slice Up The Fruit Properly. Put The Sliced Fruit
Into Feeding Port And Push Them Into The Juicer By Feeding Bar.
7. The Juicer Can Be Disassembled Only After The Running Of Motor Has Com-
pletely Stopped.
Caution:
1. The Power Switch Must Be Turned On Prior To Feeding Sliced Foods. Don’t
Use This Juicer For Processing Those Fruits That They Are Extremely Soft And
The Separation Of Juice From Residues Is Difficult.
2. The Power Must Be Turned Off Immediately If The Motor Doesn’t Run After
The Switch Has Been Turned On. It Can Be Restarted Only After The Trouble
Has Been Found Out And Remedied.
3. When It Is Used For Pressing Sugarcane, The Sugarcane Must Be Cut Into
Proper Pieces With Proper Thickness. During Operation, The Sugarcane Pieces
Should Be Pressed Down While Being Rotated.
4. When Operation Is Finished, All Parts Or Components Must Be Cleaned Up
And Assembled To Have A Dewater Operation.
5. The Main Engine Mustn’t Be Cleaned In Water Or Rinsed With
Water. It
Should Be Cleaned By Wet Cloth.
6. Don’t Operate The Juice By Children.
7. Don’t Use The Appliance If The Rotating Sieve Is Damaged
FOOD
PROCESSOR
COMBINED MULTIFUNCTION
2
A
4. Combination Of Mixer And Method For Use (In Combination With Milling
Cup, Mixing Cup, And Mincing Cup)
(1) Combination With Milling Cup And Usage
a) Put The Main Engine A On The Flat Top Of A Table.
b) Make The Milling Cup Stand Upside Down And Put The Food Into It. Attach The Blade Assem-
bly To The Milling Cup By Screwing It Clockwise.
c) Get The Milling Cup T Stood Upward And Put It Onto The Main Engine. Press Down The Mill-
ing Cup And Screw It Counterclockwise At The Same Tome So As To Make The Cramp On The
Milling Cup Firmly Fixed At The Cramping Position Of Main Engine.
d) The Milling Operation Starts When The Power Switch Is Turned On.
T
U
V
J
F
G
(2) Combination With Mixing Cup And Usage
a) Put The Main Engine On The Flat Top Of A Table.
b) Amount The Mixing Cup J To The Main Engine. Press Down The Cup And Screw It Counter-
clockwise So As To Get The Cramp On The Cup Firmly Locked At The Cramping Position Of The
Main Engine.
c) Cut The Food Into Cubes Or Slices And Then Put Them Into Mixing Cup. Put On The Mixing
Cover And Fix It Firmly By Cramp.
d) Press The Mixing Cup By One Hand And Switch On The Power By Another Hand To Start The
Mixing Operation.
FOOD
PROCESSOR
COMBINED MULTIFUNCTION
FOOD PROCESSOR
COMBINED MULTIFUNCTION
3 4
A
A
a) The Main Engine Is Placed On The Flat Table.
b) The Cup Body Installed With The Speed Regulator Is
Placed On The Principal To Press Up And Down And It Is
Rotated Counterclockwise At Same Time So That The Clip
Foot On The Cup Is Locked With The Clipper Of Main Engine
Firmly.
c) The Feed Tray (Y Stripe Faces Upward) Is Installed In The
Rotating Shaft Of Speed Regulator (Pay Attention To The
Alignment).
d) The Cutter Head Of Slicing And Section Is Installed On The
Feed Tray (Pay Attention To Hexagonal Alignment) The Cutter
Head Of Slicing Knife Can Be Used In Front And Back Face.
The Front Face Is Slicing And Back Face Is Section. The
Slicing Knife Faces Upward For Slicing .On The Contrast, It Is
Tightened.
e) The Cropping Cover Is Placed On The Cup Body To Press
Up And Down And It Is Tightened Counterclockwise At Same
Time.
f) Please Operate The Engine With No More 5 Seconds
Before Processing The Food In Order To Prolong The Service
Life Of Engine.
g) The Food Materials To Be Sliced Or Cut Are Placed In The
Charging Opening For Slicing And Section. If Necessary, The
Charging Arm Presses The Food Materials By Applying The
Force Evenly.
h) When Cleaning The Food Materials Or Assembly, The At-
taching Plug Must Be Unplugged To Avoid Danger.
(4) Combination And Use Of Slicing And Section
transfer plate
feeding bar
transparent cover
mincing cup
FOOD PROCESSOR
COMBINED MULTIFUNCTION
6
slicing blade
Food Processor
Thank You For Your Choice To Buy And Use The Series Combined Multifunction Food Processor. Please Read This Instruction
Carefully Before Use So As To Make The Functions Of This Product A Full User.
A. Engine
B. Driving Gear
C. Knob For Selection Of Speed
D. Bottom Cover
E. Knob For Quick Cleaning
F. Fixing Cramp
G. Cover Of Mixing Cup
J Mixing Cup
K Rub Seal Ring
L Assembly Of Blade
M Feeding Bar
N Feeding Passage
O Transparent Cover
P Juice Filer
Q Residue-Juice Separating Slot
R Safety Buckle
S Residue Collector
T Milling Cup
U Rub Seal Ring
V Assembly Of Miffing Blade
W Cover Of Mincing Cup
X Mincing Cup
Z Juice Cup
Caution
1. The Device Should Be Stored In A Dry And Ventilated
Place When They Are Not In Use.
2. The Razor Blade Is Very Sharp, At Cleaning With
Replace The Agitation Knife Hour Must Look Out.
3. If The Supply Cord Is Damaged, It Must Be Replaced
By The Manufacturer Or Its Service Agent Or A Similarly
Qualified Person In Order To Avoid A Hazard.
Model Number: LSU-1411
Q
FOOD
PROCESSOR
COMBINED MULTIFUNCTION
T
U
V
R
Z
S
W
X
P
O
M
F
G
J
L
K
B
A
E
C
-
1
-
2
-
3
-
4
AneX AG-3053 Operating instructions
- Category
- Slicers
- Type
- Operating instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Bosch MCM 5000 UC User manual
-
COOK Medical MINC K-MINC-1000 User manual
-
Philips HR7775/00 Datasheet
-
LKZAIY ANMIR Portable Mini Blender Personal Small Cordless Blender Juicer Mixer for Smoothies and Shakes User manual
-
Electrolux N24 User manual
-
ElectrIQ HSL600 User manual
-
Kenwood MA280 Datasheet
-
Bosch Appliances MUM 7220 UC User manual
