Canon imagePRESS 1125 Professional Customer Expectation Document

imagePRESS 1125 Professional

Customer Expectations Document

Version 3

Systems & Technical Support Division

Imaging Systems Group, Canon U.S.A., Inc.

Version 3 imagePRESS 1125P Customer Expectations Document Page 2

Contents

1. Introduction ............................................................................................................. 4

2. Product Overview ................................................................................................... 5

2.1 Summary of Functions .................................................................................... 6

2.2 Offset Press vs. Digital imagePRESS ............................................................. 6

2.3 Image Stabilization Control ............................................................................. 7

2.4 Professional Input/Output Accessories ........................................................... 7

3. Machine Dimensions and Space Requirements .................................................. 8

3.1 Dimensions ..................................................................................................... 8

3.2 Weight ............................................................................................................. 9

3.3 Installation and Service Space ........................................................................ 9

3.3.1 Minimum Space Requirements to Transport the Machine and Turn

Hallway Corners .............................................................................. 10

3.3.2 Dimensions Diagrams ...................................................................... 11

3.3.3 Installation Space Diagrams ............................................................ 12

3.4 Recommended Floor Space Requirements .................................................. 14

3.5 Floor Structure Requirements ....................................................................... 14

3.6 Network Connectivity .................................................................................... 15

4. Power/Electrical Requirements ........................................................................... 15

4.1 Power Requirements for the Main Unit and Optional Accessories ................ 16

5. Environmental Factors and Requirements ......................................................... 18

5.1 Temperature and Humidity Conditions .......................................................... 18

5.1.1 Operating the Machine in a Low Temperature Environment ............ 19

5.2 Temperature Gradient ................................................................................... 20

5.3 Ventilation ..................................................................................................... 20

5.4 Elevation Limitations ..................................................................................... 20

5.5 Lighting.......................................................................................................... 20

5.6 Sunlight ......................................................................................................... 20

5.7 Ammonia ....................................................................................................... 20

6. Specifications ....................................................................................................... 21

6.1 Main Unit ....................................................................................................... 21

6.3 Color Image Reader-L1 with Feeder ............................................................. 23

6.4 POD Deck-C1/Secondary POD Deck-C1 ...................................................... 25

6.5 Multi Drawer Document Insertion Unit-A1 ..................................................... 26

6.6 Professional Puncher-B1 and Professional Puncher Integration Unit-A1 ...... 27

6.7 Finisher-AF1 .................................................................................................. 28

6.8 Saddle Finisher-AF2 ..................................................................................... 31

6.9 Punch Unit-BB1 ............................................................................................. 34

6.10 Paper Folding Unit-F1 ................................................................................... 35

6.11 Card Reader-C1 ............................................................................................ 36

6.12 High Capacity Stacker-E1 ............................................................................. 37

6.13 Perfect Binder-C1 .......................................................................................... 38

6.14 Booklet Trimmer-D1 ...................................................................................... 39

6.15 Two-Knife Booklet Trimmer-A1 ..................................................................... 40

7. System Options .................................................................................................... 41

7.1 imagePRESS Printer Kit ............................................................................... 41

7.2 imagePRESS Server J200/J100 ................................................................... 42

7.3 PCI Bus Expansion Kit .................................................................................. 43

Version 3 imagePRESS 1125P Customer Expectations Document Page 3

7.4 System Upgrade RAM .................................................................................. 43

7.5 Additional Memory Type C (512 MB) ............................................................ 43

7.6 IPSec Board .................................................................................................. 43

7.7 Color Universal Send Kit ............................................................................... 43

7.8 Universal Send Security Feature Set-C1....................................................... 44

7.9 Universal Send Advanced Feature Set-C1 ................................................... 44

7.10 Digital User Signature Kit-B1 ......................................................................... 44

7.11 Secure Watermark-A1 ................................................................................... 44

7.12 HDD Data Encryption Kit-B7 ......................................................................... 44

7.13 HDD Data Erase Kit-A1 ................................................................................. 45

7.14 Encrypted Secure Print Software .................................................................. 45

7.15 Removable Hard Disk Drive Kit-AA1 ............................................................. 45

7.16 Remote Operator's Software Kit-A2 .............................................................. 45

7.17 Access Management System Kit-A1 ............................................................. 45

7.18 Other imagePRESS 1125P Main Unit Accessory Options ............................ 45

7.19 Notes on the Hard Disk ................................................................................. 46

8. Installation Review................................................................................................ 46

8.1 Installation Time ............................................................................................ 46

8.2 Customer Responsibilities ............................................................................. 47

9. Consumable Items ................................................................................................ 48

9.1 Usage Conditions .......................................................................................... 48

9.2 Consumable Parts ......................................................................................... 49

9.2.1 Estimated Life of Consumables ....................................................... 49

10. Toner Bottle and Hopper Unit Yields .................................................................. 49

11. Waste Toner Yields ............................................................................................... 50

12. Estimated Performance Standards ..................................................................... 50

13. Optimum Monthly Product Performance ............................................................ 51

14. Machine Reliability and Productivity................................................................... 52

14.1 Print Speed ................................................................................................... 53

14.2 Mixed Paper Weight Job Productivity ............................................................ 56

14.3 Mixplex Job Productivity ................................................................................ 56

14.4 Paper, Toner, and Waste Toner Replacement .............................................. 57

15. Media Usage/Compatibility .................................................................................. 58

15.1 Media Characteristics by Media Library Parameters ..................................... 58

15.2 Paper Handling and Storage ......................................................................... 59

15.3 Selecting the Correct Media .......................................................................... 59

15.4 Paper Grain and Curl .................................................................................... 60

15.5 Note for Customers Who Cut Their Own Paper ............................................ 61

15.6 Media Feed Locations ................................................................................... 61

15.7 Paper Sizes and Feed Location Chart .......................................................... 65

16. Image Quality Capabilities ................................................................................... 66

16.1 Customer-Defined Image Quality Adjustments and Recommendations ........ 67

16.1.1 Device Management Settings .......................................................... 68

16.1.2 Paper Type Management Settings .................................................. 69

17. Responsibility Matrix ............................................................................................ 70

Version 3 imagePRESS 1125P Customer Expectations Document Page 4

IMPORTANT

The purpose of this Customer Expectations Document is to explain the

current features and capabilities of the imagePRESS 1125P, and establish a

customer’s expectation before purchasing the machine.

The information included in this document has been pulled from various

sources, including product reference guides, service guides, user manuals,

as well as results from internal Canon testing. Specifications and other

information contained herein may vary slightly from actual device values or

those found in advertising and other printed matter. Part numbers, yield

information, and specifications are subject to change without notice;

therefore, the latest specifications may not be found in this document. As

new information becomes available, this document will be revised. Canon

authorized dealers can access the latest revision of this document from the

Download Center page in the e-Support Web site (support.cusa.canon.com).

1. Introduction

The Canon imagePRESS 1125P Customer Expectations Document contains

information about the features and capabilities of the Canon imagePRESS 1125P.

This document should be used as part of the presale and pre-installation planning

process to help clarify the requirements and responsibilities associated with

supporting, owning, and operating the imagePRESS 1125P. It is also

recommended that those interested in purchasing the imagePRESS 1125P have,

and familiarize themselves with, the information in this document prior to making

their purchase.

Version 3 imagePRESS 1125P Customer Expectations Document Page 5

2. Product Overview

The Canon imagePRESS 1125P brings the following new capabilities to the

production printing environment:

• Class Leading Image Quality – 1,200 x 1,200 dpi print resolution and an

innovative twin sleeve developing system delivers sharp text and images.

• Maximum Productivity – Full production speeds of 125 ppm are achievable,

depending on the selected media. A maximum paper size of 13” x 19.2” is

supported. Multiple paper sources, complemented by air-assisted feeding, can

hold approximately 14,000 sheets of paper for exceptional reliability and over 1.5

hours of uninterrupted production.

• Precision Printing – Accurate registration, which is automatically adjusted during

print runs, ensures consistency at high speeds.

• New Micro Toner Technology – A newly designed mono-component toner

enables the machine to reproduce pure, rich black consistently and across a

wide range of media.

• Exceptional Finishing – Select from a variety of finishing options including:

perfect binder, multi-folding unit, saddle stitch finisher, punching unit, one or

three edge trimmer, and high-capacity stacker.

Version 3 imagePRESS 1125P Customer Expectations Document Page 6

2.1 Summary of Functions

Function

imagePRESS 1125P

Output Speed (B&W)

125 ppm (LTR)

Engine Resolution

1,200 x 1,200 dpi

Gradations

256 levels

Media Size

Min

7.17” x 7.17”

Max

13” x 19.2”

Media

Thickness

Min

14 lb bond (52 g/m²)

Max

110 lb cover (300 g/m²)

HDD Capacity

80 GB

Printer Memory

Main Controller 1:

1 GB Maximum

(512 MB Standard, 512 MB Optional)

Main Controller 2:

1 GB Maximum

(512 MB Standard, 512 MB Optional)

Copy

Optional (w/Reader and Feeder)

Mail Box

Yes

Network

Yes

Remote UI

Yes

MEAP Capability

Yes

Controllers

imagePRESS Server J200

imagePRESS Server J100

imagePRESS Printer Kit-A1

Network Scanning

Optional (w/Reader and Feeder)

Send

Optional (Universal Send)

2.2 Offset Press vs. Digital imagePRESS

Offset printing is a technique that transfers (or “offsets”) an inked image from a

plate to a rubber blanket, and then to the printing surface. This enables the offset

press to maintain a consistent and high image quality over long print runs because

the plate never touches the paper. The process requires a substantial investment

in equipment and setup expense to achieve these results.

A digital press uses an electrostatic process to produce “offset-like” image quality

at a fraction of the cost of an offset press. In the imagePRESS 1125P digital press,

the drum is imaged; the toner is applied, and then transferred to the ITB

(Intermediate Transfer Belt). The ITB then transfers the toner to the paper in one

single pass. The small toner particle size provides high print quality with crisp thin

lines, high quality characters, smooth corners, and clean gradient transitions,

closer to that of an offset press.

Version 3 imagePRESS 1125P Customer Expectations Document Page 7

2.3 Image Stabilization Control

The imagePRESS 1125P contains four separate skew adjustment rollers which

ensure that an image is placed in the same location on every sheet of paper.

Accurate front to back registration is actively adjusted during print runs, and

consistency is maintained at high speeds with non-stop operation. This works

effectively for thin paper as well. Skew adjustment and shift rollers feed thin paper

accurately without folding or crumpling.

2.4 Professional Input/Output Accessories

The imagePRESS 1125P features many robust input and output accessories that

allow customers working in production environments to complete large jobs directly

from the machine. An ARCnet (Attachable Resource Computer Network)

communications cable is used to connect the accessories to the main unit. The

ARCnet cable provides the main unit’s engine information about the accessories

that are attached and if they are working properly. The ARCnet cable also enables

seamless communication between the main unit and the accessories, as there is

no significant communication delay, regardless of the many accessories that are

connected.

Input Accessories

• Feeder (DADF)

• POD Deck-C1 (combine up to three)

• Multi Drawer Document Insertion Unit-A1

Finishing (Output) Accessories

• Professional Puncher-B1

• High-Capacity Stacker-E1 (combine up to two)

• Perfect Binder-C1

• Finisher-AF1 or Saddle Finisher-AF2

• Internal Punch Unit-BB1

• Paper Folding Unit-F1

• Booklet Trimmer-D1

• Two-Knife Booklet Trimmer-A1

Version 3 imagePRESS 1125P Customer Expectations Document Page 8

3. Machine Dimensions and Space Requirements

3.1 Dimensions

The following table includes the width, height, and depth dimensions (in inches and

millimeters) of the main unit and optional accessories.

Unit

Width

Depth

Height

Main Unit

54.6”

1,387 mm

31.9”

809 mm

54.1”

1,373 mm

POD Deck-C1

29.3”

745 mm

31.2"

792 mm

43.1"

1,095 mm

Secondary POD Deck-C1

31.9”

811 mm

31.2"

792 mm

43.1"

1,095 mm

POD Deck-C1 + Secondary

POD Deck-C1

*1

61.7” 1,566 mm 31.2" 792 mm 43.1" 1,095 mm

POD Deck-C1 + (2)

Secondary POD Deck-C1s

*1

93.6” 2,377 mm 31.2" 792 mm 43.1" 1,095 mm

Multi Drawer Document

Insertion Unit-A1

42.5” 1,079 mm 31.2" 792 mm 43.1" 1,095 mm

Color Image Reader-L1

w/Feeder

24.9" 633 mm 23.5" 597 mm 10.0" 253 mm

Professional Puncher-B1 &

Professional Puncher

Integration Unit-A1

22.0” 560 mm 31.2” 792 mm 41.0” 1,040 mm

High Capacity Stacker-E1

39.3”

997 mm

31.2"

792 mm

53.6”

1,362 mm

Perfect Binder-C1

36.3”

922 mm

31.1”

791 mm

51.2”

1,300 mm

Paper Folding Unit-F1

13.2”

336 mm

31.25”

793 mm

46.9”

1,190 mm

Finisher-AF1

*2

35.4”

890 mm

31.2”

792 mm

46.5”

1,180 mm

Saddle Finisher-AF2

*3

41.75”

1,060 mm

31.2”

792 mm

46.5”

1,180 mm

Punch Unit-BB1

Part of the Finisher-AF1 or Saddle Finisher-AF2

Booklet Trimmer-D1

*2

62.0”

1,575 mm

30.3”

770 mm

41.0”

1,040 mm

Booklet Trimmer-D1

*2

&

Two-Knife Booklet Trimmer-

A1

*1

83.1” 2,116 mm 30.3” 770 mm 41.0” 1,040 mm

Booklet Trimmer-D1

*2

&

Saddle Finisher-AF2

*1, *3

74.3" 1,888 mm 31.2" 792 mm 46.5" 1,180 mm

Booklet Trimmer-D1

*2

, Two-

Knife Booklet Trimmer-A1,

& Saddle Finisher-AF2

*1

95.6” 2,429 mm 31.2” 792 mm 46.5” 1,180 mm

*1 The width includes one 1/5” (5 mm) gap between each piece of equipment attached.

*2 The extension tray is extended.

*3 The auxiliary booklet tray is extended.

Version 3 imagePRESS 1125P Customer Expectations Document Page 9

3.2 Weight

The weights of the main unit, feeding and finishing options (in pounds and

kilograms) are listed in the table below.

Unit

Weight

Main Unit

1,103 lb

500 kg

POD Deck-C1

498 lb

226 kg

Secondary POD Deck-C1

498 lb

226 kg

Color Image Reader-L1 w/Feeder

88 lb

40 kg

Multi Document Insertion Unit-A1

553 lb

251 kg

Professional Puncher-B1 &

Professional Puncher Integration

Unit-A1

258 lb 117 kg

High Capacity Stacker-E1

463 lb

210 kg

Perfect Binder-C1

674 lb

306 kg

Paper Folding Unit-F1

144 lb

65 kg

Saddle Finisher-AF2

396 lb

180 kg

Finisher-AF1

286 lb

130 kg

Booklet Trimmer-D1

335 lb

152 kg

Two-Knife Booklet Trimmer-A1

319 lb

145 kg

3.3 Installation and Service Space

The site must provide enough space for unrestricted operation, maintenance work,

and proper ventilation. The machine dimensions are in diagrams on the following

pages. Every attempt should be made to install the equipment in a room that is

large enough to allow for proper servicing and maintenance of the equipment, and

ensure that issues, such as ventilation, odors, and dust accumulation will not be a

concern.

IMPORTANT

• Keep the back of the machine at least 39.4” (1,000 mm) away from a wall.

• Installation space from the back of the machine can be reduced from 39.4”

(1,000 mm) to 31.5” (800 mm) if a technician finds that there are no other space

concerns.

• The floor must be level (with no bows) and flat for the stabilization and support of

the machine.

Version 3 imagePRESS 1125P Customer Expectations Document Page 10

3.3.1 Minimum Space Requirements to Transport the Machine and Turn Hallway

Corners

The following table represents the minimum width that is necessary to turn

hallway corners and transport the machine to its final installation site.

IMPORTANT

• The minimum doorway opening that the machine passes through prior to

installation must be at least 36” wide.

• The minimum width required for turning is the diagonal length of each piece of

equipment + 19 3/4" (500 mm).

• The machine should not be moved once it is in place.

Equipment

Dimensions When Transporting

(Depth x Width)

Minimum Corridor Width

for Turning

Main Unit

54 3/5" x 31 4/5"

(1,387 mm x 808 mm)

82 7/8"

(2,106 mm)

POD Deck-C1

31 1/4" x 29 3/8"

(792 mm x 745 mm)

62 1/2"

(1,588 mm)

Secondary POD Deck-C1

32" x 31 1/4"

(811 mm x 792 mm)

64 3/8"

(1,634 mm)

Multi Drawer Document

Insertion Unit-A1

42 1/2" x 31 1/4"

(1,079 mm x 792 mm)

72 3/8"

(1,839 mm)

Professional Puncher-B1

31 1/4" x 12"

(792 mm x 305 mm)

53 1/8"

(1,349 mm)

Professional Puncher

Integration Unit-A1

31 1/4" x 9 7/8"

(792 mm x 250 mm)

52 3/8"

(1,331 mm)

High Capacity Stacker-E1

39 1/4" x 31 1/4"

(997 mm x 792 mm)

69 7/8"

(1,774 mm)

Perfect Binder-C1

36 3/8" x 31 1/8"

(922 mm x 791 mm)

67 1/2"

(1,715 mm)

Paper Folding Unit-F1

31 1/4" x 13 1/4"

(793 mm x 336 mm)

53 5/8"

(1,362 mm)

Finisher-AF1

31 1/2" x 31 1/4"

(800 mm x 792 mm)

64"

(1,626 mm)

Saddle Finisher-AF2

31 1/2" x 31 1/4"

(800 mm x 792 mm)

64"

(1,626 mm)

Booklet Trimmer-D1

62" x 30 3/8"

(1,575 mm x 770 mm)

88 3/4"

(2,854 mm)

Two-Knife Booklet

Trimmer-A1

30 3/8" x 21 1/8"

(770 mm x 536 mm)

56 5/8"

(1,439 mm)

Version 3 imagePRESS 1125P Customer Expectations Document Page 11

3.3.2 Dimensions Diagrams

Approx.

95.6”

Approx.

39.3”

Approx.

39.3”

Approx.

54.6”

Approx.

93.6”

Approximately 436.4”

Approx.

31.9"

Provide at least 3 feet on each side of the

machine for unrestricted operation and for proper

servicing.

Approx.

40.9"

Approx.

54.1"

Approx.

36.3”

Approx.

22.0”

Approx.

42.5”

Approx.

13.2”

Version 3 imagePRESS 1125P Customer Expectations Document Page 12

3.3.3 Installation Space Diagrams

The approximate installation space requirements will differ, depending on how

your machine is configured and the optional accessories attached.

There must be enough space around the machine. The following diagrams show the

minimum dimensions; whenever possible, be sure there will be more space than indicated.

Minimum Configuration

[1] Main Unit

[3] Saddle Finisher-AF2

[2] POD Deck-C1

Professional Accessory Configuration

[1] Main Unit

[6] High Capacity Stacker-E1

[2] POD Deck-C1

[7] Perfect Binder-C1

[3] Secondary POD Deck-C1

[8] Paper Folding Unit-F1

[4] Multi Drawer Document Insertion Unit-A1

[9] Saddle Finisher-AF2

[5] High Capacity Stacker-E1

[10] Booklet Trimmer-D1

[11] Two-Knife Booklet Trimmer-A1

39.4”

59.8”

39.4”

144.7”

39.4”

402.2”

39.4”

63.9”

Version 3 imagePRESS 1125P Customer Expectations Document Page 13

Maximum Configuration

[1] Main Unit

[8] High Capacity Stacker-E1

[2] POD Deck-C1

[9] High Capacity Stacker-E1

[3] Secondary POD Deck-C1

[10] Perfect Binder-C1

[4] Secondary POD Deck-C1

[11] Paper Folding Unit-F1

[5] Multi Drawer Document Insertion Unit-A1

[12] Saddle Finisher-AF2

[6] Professional Puncher-B1

[13] Booklet Trimmer-D1

[7] Professional Puncher Integration Unit-A1

[14] Two-Knife Booklet Trimmer-A1

IMPORTANT

• The maximum configuration (fully configured machine) includes 3-POD

Decks-C1, the Main Unit, Multi-Drawer Document Insertion-A1, Professional

Puncher-B1 and Professional Puncher Integration Unit-A1, Perfect Binder-C1,

2-High Capacity Stackers-E1, Paper Folding Unit-F1, Saddle Finisher-AF2,

Booklet Trimmer-D1, and Two-Knife Booklet Trimmer-A1.

• The fully configured width of the machine includes opening space for the POD

Deck door and the extended tray of the Booklet Trimmer.

• There needs to be approximately 1/5” (5 mm) of space in between each

accessory attached.

39.4” 39.4” 456.6”

39.4”

63.9”

Version 3 imagePRESS 1125P Customer Expectations Document Page 14

3.4 Recommended Floor Space Requirements

For a fully configured imagePRESS 1125P (3-POD Decks-C1, the Main Unit,

Multi-Drawer Document Insertion-A1, Professional Puncher-B1 and Professional

Puncher Integration Unit-A1, Perfect Binder-C1, 2-High Capacity Stackers-E1,

Paper Folding Unit-F1, Saddle Finisher-AF2, Booklet Trimmer-D1, Two-Knife

Booklet Trimmer-A1, and imagePRESS Server J200/J100 with the Integrated

Interface & Stand), it is recommended that there be at least 45’ (W) x 12’ (D) of

floor space.

IMPORTANT

• The imagePRESS 1125P was created to be modular in design. Your floor space,

budget, monthly copy/print volume, and applications will determine which

configuration will work best for you. Any configuration of up to 3-POD Decks-C1

(at least one POD Deck must be attached) and 2-High Capacity Stackers-E1

may be connected at once. The Saddle Finisher-AF2, Booklet Trimmer-D1, and

Two-Knife Booklet Trimmer-A1 may be connected at the same time as well.

• The imagePRESS 1125P requires some type of finishing option (Saddle

Finisher-AF2, Finisher-AF1, or High Capacity Stacker-E1).

3.5 Floor Structure Requirements

The floor on which this machine is installed must have strength of at least

92.2 lb/ft

2

(450 kg/m

2

). If the floor does not have this level of strength, consult your

building contractor before installing the machine.

The weight of the machine is distributed on the floor through the adjusters and

wheels. Do not install the machine on an unstable floor or platform.

39.4”

456.6”

39.4”

63.9”

45’ (13.7 m)

12’ (3.7 m)

Version 3 imagePRESS 1125P Customer Expectations Document Page 15

3.6 Network Connectivity

A standard 10/100Base-T Ethernet interface (RJ-45 jack) for device installation,

monitoring, and Mail Box access, via the Remote UI, ships standard with all

configurations.

A USB 2.0 High-Speed interface port ships standard with all configurations for

direct connection to centralized environments that want to drive all jobs through a

single host PC.

4. Power/Electrical Requirements

The imagePRESS 1125P requires a NEMA L14-30 receptacle for the main unit,

ARCnet accessory configuration, and proper operation.

NEMA L14-30 Receptacle

Version 3 imagePRESS 1125P Customer Expectations Document Page 16

4.1 Power Requirements for the Main Unit and Optional Accessories

Part or Accessory Power Supply

Power Supply Cord/Plug

Specifications

Length of

Power Cord

Main Unit

1-Single Phase

208 V/30 A outlet

NEMA L14-30

9’ 8” (3 m)

1-208 V/15 A outlet NEMA 6-15

6’ (1.8 m)

POD Deck-C1

1-120 V/15 A outlet

NEMA 5-15

UL498, 2-pole, 3-wire,

grounding devices rated

250 V/15 A

6’ (1.8 m)

Secondary POD

Deck-C1

*1

1-120 V/15 A outlet

NEMA 5-15

UL498, 2-pole, 3-wire,

grounding devices rated

250 V/15 A

6’ (1.8 m)

Multi Drawer

Document Insertion

Unit-A1

1-120 V/15 A outlet

NEMA 5-15

UL498, 2-pole, 3-wire,

grounding devices rated

250 V/15 A

6’ (1.8 m)

High Capacity

Stacker-E1

*2

1-120 V/15 A outlet

(regardless of the

number of stackers

connected)

NEMA 5-15

6’ (1.8 m)

Professional

Puncher-B1 &

Professional

Puncher Integration

Unit-A1

*3

1-120 V/15 A outlet

NEMA 5-15

6’ (1.8 m)

Saddle Finisher-AF2

1-120 V/15 A outlet

NEMA 5-15

UL498, 2-pole, 3-wire,

grounding devices rated

250 V/15 A

6’ (1.8 m)

Finisher-AF1

1-120 V/15 A outlet

NEMA 5-15

UL498, 2-pole, 3-wire,

grounding devices rated

250 V/15 A

6’ (1.8 m)

Perfect Binder-C1

1-208 V/15 A outlet

NEMA 6-15

UL498, 2-pole, 3-wire,

grounding devices rated

250 V/15 A

9’ (3 m)

Two-Knife Booklet

Trimmer-A1

1-120 V/15 A outlet

NEMA 5-15

6’ (1.8 m)

imagePRESS Server

J200/J100

1-120 V/15 A outlet

NEMA 5-15

6’ (1.8 m)

Integrated Interface

& Stand for

imagePRESS Server

1-120 V/15 A outlet

NEMA 5-15

6’ (1.8 m)

*1 Each POD Deck attached (up to three) requires 1-120 V/15 A, NEMA-5-15 outlet.

*2 If you connect a second High Capacity Stacker-E1, the second stacker draws power from

the first stacker.

*3 The Professional Puncher Integration Unit-A1 provides the Professional Puncher-B1 with

power.

Version 3 imagePRESS 1125P Customer Expectations Document Page 17

IMPORTANT

• We recommend an additional standard 120 V/15 A outlet for service tools, such

as a laptop computer or vacuum that may be used when servicing or configuring

the machine.

• Use only dedicated outlets for the main unit and each optional accessory. Do not

use extension cords.

NOTE

The Punch Unit-BB1, Color Image Reader-L1 with feeder, Paper Folding Unit-F1,

and Booklet Trimmer-D1 do not require any additional outlets.

The following illustration shows the relative position of the power outlets, and

voltage requirements of each optional accessory item.

IMPORTANT

• Canon USA strongly recommends that dedicated and properly grounded outlets

be provided for the devices mentioned above. The ground connection serves to

provide the internal electronics with a reference voltage. Faulty or poor ground

sources will cause this reference voltage to fall into a range that no longer serves

as a reliable reference voltage. The internal logic and programming of the

imagePRESS 1125P will not perform reliably because there is an insufficient

difference between the internal operating signal voltages and the poor ground

reference signal. A qualified electrician can measure and provide the ground

source that the imagePRESS 1125P or any computer controlled office equipment

requires.

• Before installation, confirm that all necessary receptacles are available for your

machine configuration.

(Note: Phase converters and step down

transformers are not supported.)

Version 3 imagePRESS 1125P Customer Expectations Document Page 18

5. Environmental Factors and Requirements

Optimum Temperature Range: Between 68°F (20°C) and 80.6°F (27°C)*

Optimum Humidity Range: Between 30% and 70%

Atmospheric Pressure: 810.6 to 1,013 hPa (0.8 to 1.0 atm)

Noise (sound level): Standby: 68 dB; Operating: 83 dB

Ozone Emissions: 0.01 ppm (parts per million) or less (initial startup)

0.35 ppm or less (after a short break-in period)

* If your machine is operated in a low temperature

environment, see “5.1.1, Operating Your

Machine in a Low Temperature Environment,”

on p. 19.

NOTE

It may be necessary to use a humidifier or dehumidifier to attain the proper

humidity levels for optimal machine performance.

5.1 Temperature and Humidity Conditions

The optimal humidity range is 30% to 70% RH (Relative Humidity) with a room

temperature of 68°F to 80.6°F (20°C to 27°C).

The machine contains intelligent technology that can sense the environmental

temperature, and optimize its performance if operated outside the temperature

range. However, productivity, paper feeding, and image quality may be affected if

the machine is operated outside of these guidelines.

The machine should not be installed in locations with significant shifts in

temperature or humidity. Areas containing water, or equipment that can

significantly alter room temperature or humidity, such as a heater, stove, or

portable air conditioner, should be avoided, unless proper environmental control is

available to achieve maximum productivity or quality capability.

The optimal humidity range for storing paper is 30% to 70% RH (Relative Humidity)

with a room temperature of 68°F to 80.6°F (20°C to 27°C). Storing paper in a

location that does not meet these specifications may affect paper feeding and

image quality. For example, if the humidity is too high, paper curling and paper

jams will increase. If the humidity is too low, paper may shrink or lose resistance,

and toner will not adhere to the paper as well.

Version 3 imagePRESS 1125P Customer Expectations Document Page 19

5.1.1 Operating the Machine in a Low Temperature Environment

It is best to run your machine at a room temperature that falls within the optimal

range (68°F to 80.6°F (20°C to 27°C)); however, if a low temperature

environment cannot be avoided, and depending on your job criteria (either print

speed or image quality), you can set the machine to account for the temperature

of the room in which the machine is located.

The Adjust Fixing for Natural Conditions mode in Device Management Settings in

System Settings (from the Additional Functions screen) enables you to run the

machine at a fixed speed at any ambient temperature, or adjust the machine to

run at a speed that maximizes your machine’s productivity or image quality

output results.

There are three settings in the Adjust Fixing for Natural Conditions mode that can

improve print speed or image quality based on your site’s environmental

conditions and job criteria.

[Fixing Priority]: This mode is the default setting. Select this mode if

image quality has priority over print speed. The machine

calibrates the fixing temperature to adjust for the type of

media you select for the job, and the ambient

temperature. This mode provides the highest level of

quality, but has an impact on productivity.

[Standard]: Select this mode to achieve the engine’s rated speed

when the machine is running at a room temperature

between 59°F and 68°F (15°C and 20°C), regardless of

the selected media.

[Productivity Priority]: If the room temperature is below 59°F (15°C), select this

mode to run the machine at a constant fixing

temperature. This mode achieves output results at the

engine’s rated speed, but because of the room

temperature, it has an impact on image quality.

IMPORTANT

• It is strongly recommended that you make several test prints in each mode to

determine your desired image quality results.

• The Adjust Fixing for Natural Conditions mode is only available if it is enabled in

the Service Mode.

Version 3 imagePRESS 1125P Customer Expectations Document Page 20

5.2 Temperature Gradient

Using an air conditioner during the winter, or if a sudden temperature change

occurs, may have an adverse affect on image positioning. Sudden temperature

changes may cause the paper to bend or contract, cause the machine to

malfunction, and form condensation. To avoid these issues, control the

temperature gradient so that it does not exceed 18°F/H (10°C/H).

5.3 Ventilation

Ensure that there is an air exchange rate of at least 1.5 times per hour, and at least

3,885 ft

3

(110 m

3

) of space in the location where the machine will be installed.

This machine generates a slight amount of ozone during normal use. Although

sensitivity to ozone may vary, this amount is not harmful. Ozone may be more

noticeable during extended use or long production runs, especially in poorly

ventilated rooms. It is recommended that the room be appropriately ventilated,

sufficient to maintain a comfortable working environment, in areas of machine

operation.

5.4 Elevation Limitations

Install this machine at an elevation below 13,123’ (4,000 m) and at an air pressure

between 810.6 to 1,013 hPa (0.8 to 1.0 atm).

5.5 Lighting

We recommend installing the machine in a location with at least 500 lux

(29 1/2” (75 cm) above the floor) for normal operation and maintenance.

5.6 Sunlight

Avoid installing the machine in direct sunlight. Direct sunlight has adverse affects

on toner consistency and image quality. If direct sunlight is unavoidable, use

curtains to shade the machine. Be sure that the curtains do not block the

machine’s ventilation slots or louvers, or interfere with the electrical cord or power

supply.

5.7 Ammonia

Avoid installing the machine where ammonia is emitted. In a sufficient amount,

ammonia will attack the surfaces of the machine’s paper feed and image quality

components, thereby shortening their useful life and increasing the need for

periodic and remedial maintenance.

A professional assessment of the air quality in the room in which the machine is to

be installed is recommended prior to its installation.

Page is loading ...

Canon imagePRESS 1125 Professional Customer Expectation Document

This manual is also suitable for

Canon imagePRESS 1125 Professional Customer Expectation Document

Related papers

Other documents