Dahua IPC-HMW8441X-M/M12 Quick start guide

Brand: Dahua

Model: IPC-HMW8441X-M/M12

Type: Quick start guide

Passenger Counting Camera

Quick Start Guide

V1.0.0

Foreword

Applicable Models

IPC-HMW8441XP-M/M12-DAE-0200B-E

IPC-HMW8441XP-M/M12-DAE-0200B-O

Safety Instructions

The following signal words might appear in the manual.

Signal Words Meaning

Indicates a medium or low potential hazard which, if not

avoided, could result in slight or moderate injury.

Indicates a potential risk which, if not avoided, could result

in property damage, data loss, lower performance, or

unpredictable result.

Provides additional information as the emphasis and

supplement to the text.

Revision History

Version Revision Content Release Date

V1.0.0 First release. 2023.08

III

Important Safeguards and Warnings

This section introduces content covering the proper handling of the device, hazard prevention, and

prevention of property damage. Read carefully before using the device, and comply with the

guidelines when using it.

Transportation Requirements

 Transport the device under allowed humidity and temperature conditions.

 Pack the device with packaging provided by its manufacturer or packaging of the same quality

before transporting it.

 Do not place heavy stress on the device, violently vibrate or immerse it in liquid during

transportation.

Storage Requirements

 Store the device under allowed humidity and temperature conditions.

 Do not place the device in a humid, dusty, extremely hot or cold site that has strong

electromagnetic radiation or unstable illumination.

 Do not place heavy stress on the device, violently vibrate or immerse it in liquid during storage.

Installation Requirements

 Strictly comply with the local electrical safety code and standards, and check whether the

power supply is correct before operating the device.

 Please follow the electrical requirements to power the device.

When selecting the power adapter, the power supply must conform to the requirements of

ES1 in IEC 62368-1 standard and be no higher than PS2. Please note that the power supply

requirements are subject to the device label.

We recommend using the power adapter provided with the device.

 Do not connect the device to two or more kinds of power supplies, unless otherwise specified,

to avoid damage to the device.

 The device must be installed in a location that only professionals can access, to avoid the risk of

non-professionals becoming injured from accessing the area while the device is working.

Professionals must have full knowledge of the safeguards and warnings of using the device.

 Do not place heavy stress on the device, violently vibrate or immerse it in liquid during

installation.

 An emergency disconnect device must be installed during installation and wiring at a readily

accessible location for emergency power cut-off.

 We recommend you use the device with a lightning protection device for stronger protection

against lightning. For outdoor scenarios, strictly comply with the lightning protection

regulations.

 Ground the earthing portion of the device to improve its reliability.

 Ground the function earthing portion of the device to improve its reliability (certain models

are not equipped with earthing holes). The device is a class I electrical appliance. Make sure that

the power supply of the device is connected to a power socket with protective earthing.

 The lens is an optical component. Do not directly touch or wipe the lens surface during

installation.

Operation Requirements

 The cover must not be opened while the device is powered on.

 Do not touch the heat dissipation component of the device to avoid the risk of getting burnt.

 Use the device under allowed humidity and temperature conditions.

 Do not aim the device at strong light sources (such as lamplight, and sunlight) when focusing it,

to avoid reducing the lifespan of the CMOS sensor, and causing overbrightness and flickering.

 When using a laser beam device, avoid exposing the device surface to laser beam radiation.

 Prevent liquid from flowing into the device to avoid damage to its internal components.

 Protect indoor devices from rain and dampness to avoid electric shocks and fires breaking out.

 Do not block the ventilation opening near the device to avoid heat accumulation.

 Protect the line cord and wires from being walked on or squeezed particularly at plugs, power

sockets, and the point where they exit from the device.

 Do not directly touch the photosensitive CMOS. Use an air blower to clean the dust or dirt on

the lens.

● Strengthen the protection of the network, device data and personal information. All necessary

safety measures to ensure the network security of the device must be taken, such as using strong

passwords, regularly changing your password, updating firmware to the latest version, and

isolating computer networks. For the IPC firmware of some previous versions, the ONVIF

password will not be automatically synchronized after the main password of the system has been

changed. You need to update the firmware or change the password manually.

Maintenance Requirements

 Strictly follow the instructions to disassemble the device. Non-professionals dismantling the

device can result in it leaking water or producing poor quality images. For a device that is

required to be disassembled before use, make sure the seal ring is flat and in the seal groove

when putting the cover back on. When you find condensed water forming on the lens or the

desiccant becomes green after you disassembled the device, contact after-sales service to

replace the desiccant. Desiccants might not be provided depending on the actual model.

 Use the accessories suggested by the manufacturer. Installation and maintenance must be

performed by qualified professionals.

 Do not directly touch the photosensitive CMOS. Use an air blower to clean the dust or dirt on

the lens. When it is necessary to clean the device, slightly wet a soft cloth with alcohol, and

gently wipe away the dirt.

 Clean the device body with a soft dry cloth. If there are any stubborn stains, clean them away

with a soft cloth dipped in a neutral detergent, and then wipe the surface dry. Do not use

volatile solvents such as ethyl alcohol, benzene, diluent, or abrasive detergents on the device to

avoid damaging the coating and degrading the performance of the device.

 The lens is an optical component. When it is contaminated with dust, grease, or fingerprints, use

degreasing cotton moistened with a little ether or a clean soft cloth dipped in water to gently

wipe it clean. An air gun is useful for blowing dust away.

 It is normal for a camera made of stainless steel to develop rust on its surface after being used in

a strong corrosive environment (such as the seaside, and chemical plants). Use an abrasive soft

cloth moistened with a little acid solution (vinegar is recommended) to gently wipe it away.

Afterwards, wipe it dry.

Contents

Foreword ........................................................................................................................................................... II

Important Safeguards and Warnings ............................................................................................................. III

1 Structure ........................................................................................................................................................ 1

Unpack and Check ..................................................................................................................................................................... 1

Appearance .................................................................................................................................................................................. 2

1.2.1 IPC-HMW8441XP-M/M12-DAE-0200B-E ............................................................................................................... 2

1.2.2 IPC-HMW8441XP-M/M12-DAE-0200B-O .............................................................................................................. 2

Dimension (mm[inch]) ............................................................................................................................................................. 3

Port Definition ............................................................................................................................................................................. 4

1.4.1 IPC-HMW8441XP-M/M12-DAE-0200B-E ............................................................................................................... 4

1.4.2 IPC-HMW8441XP-M/M12-DAE-0200B-O .............................................................................................................. 5

Alarm Configuration ................................................................................................................................................................. 6

2 Installation ..................................................................................................................................................... 8

(Optional) TF Card Installation............................................................................................................................................... 8

Fixing Device ................................................................................................................................................................................ 8

2.2.1 Embedded Installation ............................................................................................................................................... 9

2.2.2 Bracket Installation ..................................................................................................................................................... 11

Connection ................................................................................................................................................................................. 13

2.3.1 Cable Connection ....................................................................................................................................................... 13

2.3.2 Installation Position ................................................................................................................................................... 14

2.3.3 Cable Layout ................................................................................................................................................................. 14

3 Network configuration ................................................................................................................................ 16

Initializing Device ..................................................................................................................................................................... 16

Modifying Device IP Address ............................................................................................................................................... 18

Logging in to WEB Interface................................................................................................................................................. 18

Cybersecurity Recommendations ............................................................................................. 20

1 Structure

Unpack and Check

 The following figures are for reference only, and the actual product shall prevail.

 For tools or accessories not mentioned in the box, please purchase them as needed.

Unpack and Check (IPC-HMW8441XP-M/M12-DAE-0200B-E)

Unpack and Check (IPC-HMW8441XP-M/M12-DAE-0200B-O)

Appearance

1.2.1 IPC-HMW8441XP-M/M12-DAE-0200B-E

Appearance

Table 1-1 Appearance description

No. Name

1 TF card slot

2 Lens

4 MIC

5 Fill light

1.2.2 IPC-HMW8441XP-M/M12-DAE-0200B-O

Appearance

Table 1-2 Appearance description

No. Name

1 TF card slot

2 Lens

4 MIC

5 Fill light

Dimension (mm[inch])

Dimension (IPC-HMW8441XP-M/M12-DAE-0200B-E)

Dimension (IPC-HMW8441XP-M/M12-DAE-0200B-O)

Port Definition

When connecting cables, it is recommended to use insulating tape and waterproof tape to avoid

short circuit and water leakage.

1.4.1 IPC-HMW8441XP-M/M12-DAE-0200B-E

Ports

Table 1-3 Functions

No. Cable Name Description

1 AUDIO

Audio input

port

RCA interface for inputting audio signals, e.g. Simulation

receiving audio signals from pickup and other equipment.

2 AUDIO

OUT

Audio output

port

RCA port, used to output audio signals to such external

devices as speaker.

3 POWER Power input

port Inputs 9-36V DC power.

4 Aviation

port

Ethernet and

power supply

port

Used for connecting to mobile video recorder.

5 LAN Ethernet port Connect to standard Ethernet cable.

6 I/O I/O port

Including alarm input and output. Different devices have

different i/o ports. For actual use, see instructions on the

device label.

7 RS-485 RS-485 port Control the PTZ

Table 1-4 I/O port description (IPC-HMW8441XP-M/M12-DAE-0200B-E)

Port Name Description

I/O

port

ALARM_OUT Alarm output port, used to output alarm signal to alarm device.

When the alarm output device is connected, ALARM_ Out can

be used together with ALARM_ OUT_ GND. For details, see

labels of cables.

ALARM_OUT_GND

ALARM_IN Alarm input port, used to receives the on-off signal of external

alarm source.

Different alarm input devices are connected to the same ground

terminal, the ALARM_ IN_ GND. For details, see labels of cables.

ALARM_IN_GND

1.4.2 IPC-HMW8441XP-M/M12-DAE-0200B-O

Ports

Table 1-5 Functions

No. Cable Name Description

1 AUDIO

Audio input

port

RCA interface for inputting audio signals, e.g. Simulation

receiving audio signals from pickup and other equipment.

2 AUDIO

OUT

Audio output

port

RCA port, used to output audio signals to such external

devices as speaker.

3 POWER Power input

port Inputs 9-36V DC power.

4 Aviation

port

Ethernet and

power supply

port

Used for connecting to mobile video recorder.

No. Cable Name Description

5 LAN Ethernet port Connect to standard Ethernet cable.

6 I/O I/O port

Including alarm input and output. Different devices have

different i/o ports. For actual use, see instructions on the

device label.

7 RS-485 RS-485 port Control the PTZ

Table 1-6 I/O port description

Port Name Description

I/O

port

ALARM_OUT Alarm output port, used to output alarm signal to alarm device.

When the alarm output device is connected, ALARM_ Out can

be used together with ALARM_ OUT_ GND. For details, see

labels of cables.

ALARM_OUT_GND

ALARM_IN Alarm input port, used to receives the on-off signal of external

alarm source.

Different alarm input devices are connected to the same ground

terminal, the ALARM_ IN_ GND. For details, see labels of cables.

ALARM_IN_GND

Alarm Configuration

Connect the camera to alarm input device, see Figure 1-9.

Device collects different states of alarm input port when the input signal is idling and being

grounded.

 Device collects logic “1” when input signal is connecting to +4.5 V to +36 V.

 Device collects logic “0” when input signal being connected to the ground or idling.

Alarm input

Connect to alarm output device, see Figure 1-10.

The alarm output is switch output, which can only connect to NO alarm devices.

Port ALARM_OUT and ALARM_OUT_GND form a switch, which can be used to provide alarm

output. Normally the switch is on; the switch will be off when there is alarm output.

Alarm input

 Alarm input on the WEB client is corresponding to the alarm input end of I/O port.

Please set the input mode to “NO” (default) if the alarm input signal is logic “0” and to

“NC” if the alarm input signal is logic “1”.

 The alarm output on the WEB client is corresponding to the alarm output end of I/O

port.

2 Installation

(Optional) TF Card Installation

The device has a TF card slot. Please install the TF card to store videos. Cut off the power supply

before installing TF card. Here takes IPC-HMW8441XP-M/M12-DAE-0200B-O as example.

Use a T15 wrench to loosen the two screws on the TF card cover.

Open the card cover.

Insert the TF card into the card slot with the metal side facing towards the lens. After

inserting the card, you will hear a "click" sound.

TD card installation

Fixing Device

The installation method is embedded installation and bracket installation.

 Make sure the installation surface can withstand at least three times the combined weight of

the bracket and the device to be installed. For bracket installation, the thickness of the

installation surface shall be more than 5mm.

 To ensure the monitoring effect, it is recommended that the installation height of the device

should be between 1.9m and 5m. For bracket installation, the angle between the monitoring

direction of the device and the ground should be between 20 ° and 30 °.

2.2.1 Embedded Installation

Cut installation hole

Select a flat mounting surface and stick the installation sticker on the mounting surface.

Cut a mounting hole on the mounting surface along the reference line of the installation

sticker.

Installation sticker

Cut installation hole

Adjusting angle

Use a cross screwdriver to loosen four adjusting screws on both sides of the camera until the

camera can rotate.

Embed the camera into the mounting hole.

Embed the camera

Connecting device and mobile video recorder, log in to the WEB interface of the device,

preview the video image in real time, and adjust the lens angle of the camera according to

the image to align it with the required monitoring position. See “3.3Logging in to WEB

Interface” for logging in to the WEB interface.

Adjusting angle

Adjust the lens to a proper angle, and tighten four adjusting screws on both sides of the

camera.

Fixing device

Screw in 4 ST4×25 self-tapping screws according to the screw hole position on the sticker to fix the

equipment on the mounting surface.

Fixing device (1)

Fixing device (2)

2.2.2 Bracket Installation

Cut installation hole

Select a flat mounting surface and attach the bracket to the mounting surface.

Screw in gaskets and ST4.2×30 self-tapping screws according to the screw hole position, fix

the bracket on the mounting surface.

Fix bracket

Install the camera on the bracket, take out 4 M4×10 fixing screws from the accessory bag,

and fix the camera on the bracket.

Fix camera (1)

Fix camera (2)

Adjusting angle

Use a cross screwdriver to loosen the adjusting screws on both sides of the camera until the

camera can rotate.

Loosen the adjusting screws

Connecting device and mobile video recorder, log in to the WEB interface of the device,

preview the video image in real time, and adjust the lens angle of the camera according to

the image to align it with the required monitoring position. See “3.3Logging in to WEB

Interface” for logging in to the WEB interface.

Adjusting angle

Adjust the lens to a proper angle, and tighten the adjusting screws on both sides of the camera.

Connection

2.3.1 Cable Connection

Connect the camera to the mobile video recorder to realize real-time monitoring. For details,

see”1.4Port Definition”.

 The mobile video recorders of various manufacturers are different. Please refer to the actual

equipment for details.

 Camera with PoE port needs to be connected with extension cable, and the specification of

extension cable is D-type/RJ45/6-pin aviation connector. The extension cable is not equipped by

default. Purchase it as needed.

2.3.2 Installation Position

The installation position of camera is above the door of the vehicle (installed inside the vehicle), and

the video screen should cover the area where passengers get on and off.

2.3.3 Cable Layout

There are two main installation positions of the mobile video recorder: the top of the door (the

position of the air conditioning box) and the back of the driver's seat (the device box). There are two

ways to lay the cable.

Use the extension cable to connect the camera and the mobile video recorder, and lay the cable as

shown in the figure. (Here we take the rear door installation as an example, and the installation on

the front door is the same.)

Page is loading ...

Dahua IPC-HMW8441X-M/M12 Quick start guide

Dahua IPC-HMW8441X-M/M12 Quick start guide

Dahua IPC-HMW8441X-M/M12 Quick start guide

Related papers

Other documents