Andersen 400 Series Frenchwood® Gliding - 0005406 Service Instructions

Andersen
Brand
Andersen
Model
400 Series Frenchwood® Gliding - 0005406
Type
Service Instructions
Insect Screen Stop Replacement Guide
Weight of window and door
unit(s) and accessories will vary.
Use a reasonable number of
people with sufficient strength
to lift, carry, and install window
and door unit(s) and accessories.
Always use appropriate lifting
techniques.
Use of ladders and/or scaffolding
and working at elevated levels may
be hazardous. Follow equipment
manufacturer's instructions for safe
operation. Use extreme caution when
working around window and door
openings. Falling from opening may
result in personal injury or death.
Improper use of hand or
power tools could result
in personal injury and/or
product damage. Follow
equipment manufacturer's
instructions for safe
operation. Always wear
safety glasses.
Every assembly and installation is different (windloads, structural support, etc.), and Andersen strongly
recommends consultation with an Andersen supplier or an experienced contractor, architect, or structural engineer
prior to the assembly and installation of any Andersen product. Andersen has no responsibility in regard to the
post-manufactured assembly and installation of Andersen products.
Read all instructions carefully before attempting this procedure. If you have any questions about your ability
to complete this procedure, call Andersen at 1-888-888-7020 for further direction. Andersen WindowCare®
service center hours are Monday through Friday, 7 a.m. to 7 p.m. Central Time and Saturday, 8 a.m. to 4 p.m.
Central Time. Thank you for choosing Andersen® products.
“Andersen” and “Andersen WindowCare” are registered trademarks of Andersen Corporation. All other marks where denoted are marks of Andersen Corporation.
©2005 Andersen Corporation. All rights reserved. Instruction Guide 0005406 Revised 03/31/05
Insect Screen Stop Replacement Guide
for Andersen® 400 Series Frenchwood® Gliding 4-Panel Patio Doors
Tools and Supplies
• Safety Glasses
• Phillips Screwdriver
• Wood Filler
• Putty Knife
• Pencil
• Drill
• 3/64" Drill Bit
Component Identification
#7 x 5/8" Pan
Head Screw
Insect Screen Stop
Parts Included
(1) Instruction Guide
(1) Insect Screen Stop
(2573613) white
(2653819) gray
(2) #7 x 5/8" Pan Head Screws
(888292910) white
(888292911) gray
1
1. Remove Insect Screen Stop
2. Apply Replacement Insect Screen Stop
• Mark screen edge of existing Insect Screen Stop
using a pencil.
• Remove Insect Screen Stop and discard.
• Fill screw holes using wood filler following
manufacturer’s instructions.
• Position screen edge of replacement Insect Screen
Stop at previously marked location.
• Drill two 3/64" pilot holes into Head Jamb, 5/8" deep,
using replacement Insect Screen Stop as a template.
• Fasten Insect Screen Stop into Head Jamb, using
#7 x 5/8" Pan Head Screws.
Exterior View
Exterior View
Existing Insect
Screen Stop
#7 x 5/8" Pan
Head Screws
Replacement Insect
Screen Stop
Pencil Mark
Pencil Mark
Screen Edge of
Existing Stop
Screen Edge of
Replacement Stop
Insect Screen Stop Replacement Guide
2
  • Page 1 1
  • Page 2 2

Andersen 400 Series Frenchwood® Gliding - 0005406 Service Instructions

Andersen
Brand
Andersen
Model
400 Series Frenchwood® Gliding - 0005406
Type
Service Instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents