Hubbell Wiring Device-Kellems HBLIPRBOX Installation guide

Type
Installation guide
+XEEHOO:LULQJ'HYLFH.HOOHPV+8%%(//,1&25325$7(''HODZDUH
6KHOWRQ&7
ZZZKXEEHOOZLULQJFRP
&RQWURO1R 3DJH RI
5HY 'DWH :LULQJ'HYLFH.HOOHPV,QVWUXFWLRQ6KHHW
®&RQWURO1R  3DJH RI
5HY 'DWH
+:6 
1 3/26/20
+:6  
1 3/26/20 PLENUM RATED CORD REEL ENCLOSURE
Catalog Number:
HBLIPRBOX
Kit includes: (1) Enclosure (1) 4" Square Outlet Box, Cord Reel brackets and internal mounting hardware.
Cord reel with cord, plugs, power receptacle and cover plate sold seperately.
inREACH Cord Reel sold
seperately
4" Square Outlet
Box (included)
Enclosure
1
3) Attach unit to threaded rods or hanging
support cables prior to cord reel installation
and wiring. (Not provided)
1) Install (4) threaded rods
(MAX. 5/16" diameter) or (4)
appropriate load rated braided
cables to building structure in
accordance to national and local
building code. Requires dedi-
cated support rod/cables per
NEC 300.11
4) When threaded rods are
used, secure enclosure to rods
using appropriate washers and
hex nuts. (2) washers and hex
nuts per rod, Figure 1A.
Ceiling tile
Fig. 1
NOTE: For enclosure installation details
refer to national and local building codes.
Enclosure Installation:
4
Continued from page 3
Fig. 8
Fig. 9
NOTE: Maximum Weight Capacity = 75 Lbs.
Secure outlet box to
studs with provided (2)
#8-32 nuts, (tighten nuts
to 16 inch/lb) Figure 8.
Large Plug Installation
,IWKH&RUG5HHOSOXJLVWRRODUJHWR¿WWKURXJKWKH
opening in the door, temporarily remove the door
bracket to slide the cord through, then re-assemble
door bracket, (tighten nuts to 16 inch/lb) Figure 9.
NOTE: Consult inREACH
Cord Reel instructions for Plug
and Outlet device requirements.
Install appropriate electrical
outlet receptacle and cover plate
(not included) per manufacturers
instructions and NEC.
Note: Enclosure is Suitable for Use in Other Environmental Air Space (Plenums) in Accordance with
Section 300.22(c) of the National Electrical Code.
3
2) Add T-Bar section(s)
to complete the grid
around the enclosure.
T-Bar
Fig. 1A
&RQWURO1R 3DJH RI
5HY 'DWH
&RQWURO1R 3DJH RI
5HY 'DWH
+:6  
1 3/26/20
+:6  
1 3/26/20
2inREACH Cord Reel Assembly
Fig. 2
Removable
Mounting Bracket
Fixed Mounting
Bracket
1) Unassemble Removable
Mounting Bracket and set
aside, Figure 2.
2) Slide Cord Reel base under Fixed Mounting
Bracket in the enclosure, Figure 3.
3) Base slides under
Fixed Mounting
Bracket, Figure 4
Mounting
Studs
4) Place Removable Mounting Bracket
on Cord Reel base over studs. Secure
Removable Mounting Bracket with (2)
nuts, (tighten nuts to 20 inch/lb Min.)
Figure 5.
3Outlet Box Installation
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
1) Remove Knock Out Plug
from Enclosure, Figure 6.
2) Remove Knock Out
from 4" Square Outlet Box,
Figure 7.
2Continued from page 2
  • Page 1 1
  • Page 2 2

Hubbell Wiring Device-Kellems HBLIPRBOX Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI