HeatStar HSSVFB30NGBT Owner's manual

Brand: HeatStar

Model: HSSVFB30NGBT

Category: Space heaters

Type: Owner's manual

1Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

HEATSTAR, 4560 W. 160TH ST., CLEVELAND, OHIO 44135 · 866-447-2194 2018 - CB

Installer: Leave this manual with the appliance. Consumer: Retain this manual for future reference.

UNVENTED LP-GAS FIRED ROOM HEATER

HSSVFBF10LPT

HSSVFRD10LPT

OPERATING INSTRUCTIONS

AND OWNER’S MANUAL

READ INSTRUCTIONS CAREFULLY: Read and follow all instructions. Place instructions in a safe

place for future reference. Do not allow anyone who has not read these instructions to assemble,

light, adjust or operate the heater.

Model #

WARNING: If the information in this manual is not followed exactly, a re or explosion may result causing

property damage, personal injury, or loss of life.

- Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Shut o gas supply

• Do not try to light any appliance

• Do not touch an electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

- Installation and service must be performed by a qualied installer, service agency, or the gas supplier.

WARNING: This is an unvented gas-red heater. It uses air (oxygen) from the room in which it is installed.

Provisions for adequate combustion and ventilation air must be provided. Refer to Fresh Air for Combustion and

Ventilation section on page 4 of this manual.

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property

damage. Refer to this manual for correct installation and operational procedures. For assistance or additional

information consult a qualied installer, service agency, or gas supplier.

This appliance may be installed in an aftermarket permanently manufactured (mobile) home, where not prohibited

by local codes. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not

convertible for use with any other gas.

Blue Flame Heaters

HSSVFBF10LPT

Plaque Heaters

HSSVFRD10LPT

2Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

CONTENTS

WARNINGS ........................................................................2

SPECIFICATIONS ................................................................3

PRECAUTIONS ...................................................................3

THERMOSTATIC CONTROL ................................................4

DETERMINING THE TYPE OF HEATER LOCATION SPACE ....4

INSTALLATION ...................................................................5

FASTENING HEATER TO WALL ...........................................6

FLOOR MOUNTING AWAY FROM WALL ...........................8

CONNECTING TO GAS SUPPLY ..........................................8

OPERATING YOUR HEATER ..............................................10

CLEANING AND MAINTENANCE ...................................... 11

TROUBLESHOOTING ........................................................ 12

PARTS LIST AND DIAGRAM ........................................ 14-15

WARRANTY .................................................................... 16

CAUTION: Never connect heater directly to

the Propane supply. This heater requires an

external regulator (not supplied). Install the

external regulator between the heater and

Propane/LP supply.

The installer must supply an external

regulator. The external regulator will reduce

the incoming gas pressure to between 11

and 14 inches of water. If you do not reduce

incoming gas pressure heater regulator

damage could occur. Install external

regulator with the vent pointing down.

Pointing the vent down protects it from

freezing rain or sleet.

WARNINGS

IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or

service this heater. Improper use of this heater can cause serious injury or death from burns, re, explosion,

electrical shock, and carbon monoxide poisoning.

WARNING: This appliance is equipped for propane

gas. Field conversion is not permitted.

WARNING: Do not use any accessory not

approved for use with this heater.

WARNING: Any change to this heater or its

controls can be dangerous.

• Do not place clothing or other ammable

material on or near the appliance.

• Due to high temperatures, heater should be

kept out of trac and away from furniture and

draperies.

• Surface of heater becomes very hot when

running. Keep children and adults away

from hot surfaces to avoid burns or clothing

ignition. Heater will remain hot for a time

after shutdown. Allow heater surfaces to cool

before handling.

• Young children should be carefully supervised

when they are in the same room with heater.

• Make sure grille guard is in place before

running heater. If screen or grille guard is

removed for servicing it must be replaced prior

to operating the heater.

• Keep the appliance area clear and free from

combustible materials, gasoline, and other

ammable vapors and liquids.

• Children and adults should be alerted to the

hazard of high surface temperature and should

stay away to avoid burns or clothing ignition.

• Any safety screen or guard removed for

servicing an appliance must be replaced prior

to operating the heater

In order to provide the best service possible HEATSTAR is now giving you

more ways to get in touch with us:

WEBSITE: Enerco Technical Products’s full line of product are now at:

WWW.HEATSTARBYENERCO.COM

FACEBOOK: Find us on Facebook

TWITTER: Find us on twitter

YouTube: There are now informational videos on YouTube.

SOCIAL MEDIA

3Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

DANGER: Carbon monoxide poisoning may lead to

death.

Carbon Monoxide Poisoning:

Early signs of carbon monoxide poisoning resemble

the u, with headaches, dizziness, or nausea. If you

have these signs, the heater may not be working

properly. Get fresh air at once! Have heater serviced.

Some people are more aected by carbon monoxide

than others. These include pregnant women, persons

with heart or lung disease or anemia, those under the

inuence of alcohol, and those at high altitudes.

Propane/LP Gas:

Propoane/LP gas is odorless. An odor making agent is

added to propane/LP gas. The odor helps you detect

a Propane/LP gas leak. However the odor added to

propane/LP gas may be present even though no odor

exists. Make certain you read and understand all

warnings. Keep this manual for reference. It is your

guide to safe and proper operation of this heater.

Product Features

Figure 1

PRECAUTIONS:

1. 10,000 BTU may be installed in a bedroom, but shall

not be installed in a bathroom or any place where a

strong wind would shut down the appliance.

2. This heater needs outside ventilation air to run

properly. The Oxygen Depletion Sensor (ODS) safety

shuto system shuts down the heater if not enough

fresh air is available. See Fresh Air for Combustion

and Ventilation, page 5.

3. Keep all air openings in heater clear, free of debris

or any blockage. This will insure that enough air for

proper combustion enters the heater.

4. If heater shuts o, do not relight until you provide

fresh, outside air. If heater keeps shutting o, it

requires servicing.

5. Turn o and let cool before servicing. Only a qualied

service person should service and repair heater.

6. Do not run heater:

• Where ammable liquids or vapors are used or stored

• During dusty conditions.

7. Before using furniture polish, wax, carpet cleaner or

similar products, turn heater o. If heated the vapors

from these products may create a white powder

residue within burner box or on adjacent walls or

furniture.

8. Do not use heater if any part has been underwater.

Immediately call a qualied service technician to

inspect the room heater and to replace any part of

the control system and any gas control which has

been underwater.

9. Operating heater above elevations of 4,500 feet

could cause pilot/ODS to shutdown heater.

10. Always run heater with control knob in a locked

position. Never set control knob between locked

positions. Poor combustion and higher levels of

carbon monoxide may result if control knob is left

between locked positions.

Control Knob

Grill

Front Panel

Burners

Heater

Cabinet

**Operating heater above elevations of 4,500 feet could cause pilot/ODS to shutdown heater.**

SPECIFICATIONS

MODEL HSSVFRD10LPT HSSVFBF10LPT

BTU (Available) 10,000 10,000

Type of Gas LP-Gas Only LP-Gas Only

Ignition Electronic Pulse (AA Battery) Electronic Pulse (AA Battery)

Pressure Regulator Setting 10 Inches of Water 10 Inches of Water

Inlet Gas Pressure (Maximum) 14 Inches of Water 14 Inches of Water

Inlet Gas Pressure (Minimum) 11 Inches of Water 11 Inches of Water

Burners / Orice nozzles 2 1

Thermostatic Control Yes Yes

Clearances: inches (mm)

Top 36” (915cm) 36” (915cm)

Sides 10” (254cm) 10” (254cm)

Floor (min. to top of carpet) 3” (76cm) 3” (76cm)

Fabric / ammable objects 36” (915cm) 36” (915cm) 36” (915cm)

4Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

atmosphere have a continuous water vapor retarder

with a rating of one perm (6 x 10-11 kg per pa-sec-m2)

or less with openings gasketed or sealed and

b. Whether stripping has been added on operable

windows and doors, and

c. Caulking or sealants are applied to areas such

as joints around windows and door frames,

between wall-ceiling joints, between wall panels, at

penetrations for plumbing, electrical, and gas lines,

and at other openings.

If you home does not meet all of the three criteria

above, see Determing the Type of Heater Location

Space, below.

Conned Space and Unconned Space

The National Fuel Gas Code, NFPA 54/ ANSI Z223.1

denes a conned space as a space whose volume is

less than 50 cubic feet per 1,000 Btu per hour (4.8 m3

per kW) of the aggregate input rating of all appliances

installed in that space, and an unconned space as a

space whose volume is not less than 50 cubic feet per

1,000 Btu per hour (4.8 m3 per kW) of the aggregate

input rating of all appliances installed in that space.

Rooms communicating directly with the space in which

the appliances are installed*, through openings not

furnished with doors, are considered a part of the

unconned space.

*Adjoining rooms are communication only if there

are odorless passageways or ventilation grills

between them.

DETERMINING THE TYPE OF HEATER

LOCATION SPACE:

Use this method to determine if you have a conned or

unconned space.

Note: the space includes the room in which

you install heater plus any adjoining rooms with

doorless passageways or ventilation grills between

the rooms.

1. Find the volume of the space by multiplying room

length x width x height.

Example: Space size 18ft (length) x 18ft. (width) x 8ft.

(height) = 2592

If additional ventilation to adjoining room is supplied

with grills or openings, add the volume of these rooms

to the total volume of the space.

2. Divide the space volume by 50 cubic feet to

determine the maximum Btu/hr the space can

support.

Example: 2592 cu.ft. (volume of space) / 50 cu.ft. =

51.8 or 51,800 (maximum Btu/hr the space

can support)

WARNING: If the area in which the heater may be

operated is smaller than dened as an unconned

space or if the building is of unusually tight

construction, provide adequate combustion and

ventilation air by the methods described in the

National Fuel Gas Code, NFPA 54/ ANSI Z223.1,

Section 5.3 or applicable local codes.

SAFETY DEVICE

This heater has a pilot with an Oxygen Depletion

Sensor (ODS) safety shut o system. The ODS/pilot

shuts o the heater if there is not enough fresh air.

IGNITION SYSTEM

PIEZO: The heater is equipped with an electronic

manual ignitor. This system requires no matches, or

other source to light heater, but does require one AA

battery to operate ignitor. (AA Battery included).

THERMOSTATIC CONTROL

These heaters have a control valve with a thermostat

sensing bulb. This results in the greatest heater comfort

and may reult in lower fuel bills.

LOCAL CODES

Install and use heater with care.

Installation must conform to local codes or in the

absences of local codes, use the latest edition of

National Fuel Gas Code ANSI Z223.1/NFPA 54.

UNPACKING

1. Remove heater from carton.

2. Remove all protective packaging applied to

heater for shipment.

3. Check heater for any shipping damage. If

heater is damaged, promptly inform dealer

where you bought heater.

FRESH AIR FOR COMBUSTION AND

VENTILATION

WARNING: This heater shall not be installed in

a conned space or unusually tight construction

unless provisions are provided for adequate

combustion and ventilation air. Read the following

instructions to insure proper fresh air for this and

other fuel-burning appliances in your home.

ESTABLISHING ADEQUATE VENTILATION

The following are excerpts from National Fuel Gas

Code, NFPA 54/ ANSI Z223.1, Section 5.3, Air for

Combustion and Ventilation. All spaces in homes fall

into one of the three following ventilation classications:

1. Unusually Tight Construction

2. Unconned Space

3. Conned Space

This heater must not be installed in a conned space

or unusually tight construction unless provisions are

provided for adequate combustion and ventilation air.

The information on pages 4 through 5 will help you

classify your space and provide adequate ventilation.

Unusually Tight Construction

If your home meets all of the three following criteria you

must provide additional fresh air. See Ventilation Air

from Outdoors, page 5.

Unusually tight construction is dened as construction

where:

a. Walls and ceilings exposed to the outside

5Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

outdoors or spaces open to the outdoors. These

include attics* and crawl spaces. Follow the National

Fuel Gas Code NFPA 54/ ANSI Z223.1, Section 5.3,

Air for Combustion and Ventilation for required size of

ventilation grills or ducts.

*IMPORTANT: Do not provide openings for inlet or

outlet into attic. If attic has a thermostat-controlled

power vent, heated air entering the attic will activate

the power vent.

IMPORTANT: Vent-free heaters add moisture to

the air. Although this is benecial, installing heater

in rooms without enough ventilation air may cause

mildew to form from too much moisture. See Fresh

Air for Combustion and Ventilation, pages 4

through 5.

INSTALLATION

NOTICE: This heater is intended for the use as

supplemental heat. Use this heater along with your

primary heating system. Do not install this heater as

your primary heat source. If you have a central heating

system, you may run system’s circulating blower while

using heater. This will help circulate the heat throughout

the house. In the event of a power outage, you can use

this heater as your primary heat source for the duration

of the outage.

3. Add the Btu/hr of all the fuel-burning appliances

in the space such as, Vent–free heater, Gas water

heater, Gas furnace, Vented gas heater, Gas

replace logs, and Other gas appliances*

*Do not include direct-vent gas appliances. Direct-

vent draws combustion air from the outdoors and

vents to the outdoors.

Example:

Gas water heater 40,000 Btu/hr

Vent Free Heater + 20,000 Btu/hr

Total =60,000 Btu/hr

4. Compare the maximum Btu/hr the space can support

with the actual amount of Btu/hr used.

Example: 51,800 Btu/hr (maximum Btu/hr the

space can support)

60,000 Btu/hr (Actual amount of Btu/hr used)

The space in the above example is a conned

space because the actual Btu/hr used is more than

the maximum Btu/hr the space can support.

You must provide additional fresh air. Your options

are as follows:

A. Rework worksheet, and the space of an adjoining

room. If the extra space provides an unconned

space, remove door to adjoining room or add

ventilation grills between the rooms. See Ventilation

Air From Inside Building (Fig. 2)

B. Vent room directly to the outdoors. See Ventilation

Air From Outdoors (Fig. 3).

C. Install a lower Btu/hr heater if lower Btu/hr size

makes room unconned.

If actual Btu/hr used is less than the maximum

Btu/hr the space can support, the space is an

unconned space. You will need no additional fresh

air ventilation.

VENTILATION AIR

Ventilation from Inside Building

This fresh air would come from an adjoining unconned

space. When ventilation to an adjoining unconned

space, you must provide two permanent openings: one

within 12” of the ceiling and one within 12” of the oor

on the wall connecting the two spaces (see options

1 & 2 of gure 2). You can also remove door into

adjoining room (see option3, g 2). Follow the National

Fuel Gas Code NFPA 54/ ANSI Z223.1, Section 5.3,

Air for Combustion and Ventilation for required size of

ventilation grills or ducts.

WARNING: Rework worksheet, adding the space

of the adjoining unconned space. The combined

space must have enough fresh air to supply all

appliance in both spaces.

Ventilation from Outdoors

If necessary provide extra fresh air by using ventilation

grills or ducts. Connect these items directly to the

Ventilation

Gills into

Adjoining

Room - Op-

tion 1

Ventilation Gills into Ad-

joining Room - Option 2

12”

Or remove

door into

Adjoining

Room -

Option 3

INLET

AIR

OUTLET

AIR

VENTILATION CRAWL SPACE

TO CRAWL

SPACE

TO ATTIC

VENTILATION AIR

VENTILATED

ATTIC

OUTLET AIR

Figure 2

Figure 3.

6Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

WARNING: A qualied service person must install

heater. Follow all local codes.

CHECK GAS TYPE

Use only LP-gas. If your gas supply is not LP-gas, do

not install heater. Call dealer where you bought heater

for proper type heater.

THIS INSTALLATION REQUIRES:

Before installing heater, make sure you have the items

listed below:

• Piping (check local codes)

• Sealant (resistant to LP_Gas)

• Equipment shuto valve*

• Ground joint union

• Test gauge connection*

• Sediment trap

• Tee joint

• Pipe wrench

*A CSA/AGA certified equipment shutoff valve with

1/8” NPT tap is an acceptable alternative to test gauge

connection. Purchase a CSA/AGA certied equipment

shuto valve from your dealer.

LOCATING HEATER

This heater is designed to be mounted on the wall. The

heater can also be located on a non-combustible oor,

away from a wall by using the oor mounting stands

included with the heater. If installed on combustible

ooring such as carpeting, tile or other combustible

material other than wood ooring, the heater must be

placed on a wood panel the full width and depth of the

appliance.

For convenience and eciency, install the heater:

• Where there is easy access for operation,

inspection, and service.

• In the coldest part of the room.

CAUTION: If you install the heater in a home garage:

• Heater pilot and burner must be at least 18

inches above oor .

• Locate heater where moving vehicle will not hit it.

CAUTION: This heater creates warm air currents. These

currents move heat to wall surfaces next to heater.

Installing heater next to vinyl or cloth wall covering or

operating heater where impurities (such as tobacco

smoke, aromatic candles, cleaning uids, oil or kerosene

lamps, etc.) are present in the air may discolor walls.

WARNING: Never install the heater:

• In a recreational vehicle .

• Where curtains, furniture, clothing, or other

ammable objects are less than 36 inches from

the front, top, or sides of the heater.

• As a replace insert

• In high-trac areas

• In windy or drafty areas

WARNING: Heater must be mounted to maintain

the minimum clearances shown in Figure 4. If

possible, provide greater clearances from the oor,

ceiling, and joining walls.

FASTENING HEATER TO WALL

Mounting Bracket

The mounting bracket in located on the back panel

of heater (see gure 5). It has been taped there for

shipping. Remove mounting bracket from back panel.

Figure 5

Removing Front Panel of Heater

1. Remove (4) screws total there are (2) screws

on either side of the heater (Figure 6)

2. Pull the front panel and back panel apart.

Attaching Mounting Bracket to Wall

Use holes on each end of mounting bracket to attach

bracket to wall. These holes are 16 inches apart. Attach

mounting bracket to wall in one of two following ways.

1. Attach to wall studs

2. Attach to wall anchor

Mounting

Bracket

Left

Side Right

Side

36” (915cm)

min. from ceiling

3” (7.62cm) min. to top surface

of carpet, tile or other combustible

material

Floor

10”(254cm)

from sides

Figure 4

7Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

Figure 6

Attaching to Wall Stud:

This way is the best providing the strongest mounting in

wood frame houses.

Attaching to Wall Anchor:

This way allows you to attach mounting bracket to

hollow walls (wall areas between studs) or to solid walls

(concrete or masonry).

Decide which way best suits your needs. Either method

will provide a secure hold for the mounting bracket.

1. Tape mounting bracket to wall where heater

will be located. Make sure mounting bracket is

level. For wall stud mounting locate one end of

the mounting bracket over a wall stud.

WARNING: Maintain minimum clearances

shown in gure 7. If you can, provide greater

clearances from the oor and joining wall.

2. Mark screw locations on wall (see gure 7).

3. Remove tape and mount bracket from wall.

Figure 7

Attaching to Wall Stud:

For attaching mounting bracket to wall studs

1. Drill holes at marked locations using 9/64” drill

bit.

2. Place mounting bracket onto wall. Line up

holes on each end of bracket with hole drilled in

wall.

3. Insert mounting screws through bracket and

into wall studs.

4. Tighten screws until mounting bracket is rmly

fastened to wall studs.

Attaching to Wall using Anchor:

For attaching mounting bracket to hollow walls (wall

areas between studs) or solid walls (concrete or

masonry)

Note: Wall anchors, mounting screws, and spacer

are in hardware package. The hardware package is

provided with heater.

1. Drill holes at marked locations using 5/16” drill

bit. For solid walls (concrete or masonry), drill

at least 1” deep.

2. Fold wall anchor as shown in gure 8 below.

Figure 8.

3. Insert wall anchor (wings rst) into hole. Tap

anchor ush to wall.

4. For thin walls (1/2” or less) insert red key into

wall anchor.

5. Place mounting bracket onto wall. Line up

holes on each end of bracket with wall anchors.

6. Insert mounting screws through bracket and

into wall anchors.

7. Tighten screws until mounting bracket is rmly

fastened to wall.

Placing Heater on Mounting Bracket

1. Locate two horizontal slots on back pane of

heater (see gure 9).

2. Place heater onto mounting bracket. Slide

horizontal slots onto stand-out tabs on

mounting bracket.

Figure 9

Installing Bottom Mounting Screws

1. Locate two bottom mounting holes. These

holes are near bottom on back panel of heater

(see gure 10).

Adjoining Wall

18” Min.

See clearance

specs on Pg 3

16” (Lg)

12-9/64” (Sm)

Mark mounting hole locations

and drill holes where indicated.

Allow for minimum clearances

Horizontal Slots

Mounting Bracket

mounted to wall

(2) Screws

8Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

Figure 10

2. Mark screws locations on wall.

3. Remove heater from mounting bracket.

4. If installing bottom mounting screw into hollow

or solid wall, install wall anchors. Follow steps

1 through 4 under Attaching to Wall using

Anchor. If installing bottom mounting screw into

wall stud, drill holes at marked locations using

9/64” drill bit.

5. Re-place heater onto mounting bracket.

6. Place spacers between bottom mounting holes

and wall anchor or drilled hole.

7. Hold spacer in place with one hand. With the

other hand, insert mounting screw through

bottom mounting hole and spacer. Place tip of

screw in opening of wall anchor or drilled hole.

8. Tighten both screws until heater is rmly

secured to wall. Do not over tighten.

Note: Do not re-place front panel at this time.

Replace front panel after making gas connections

and checking for leaks.

Floor MOUNTING AWAY FROM WALL

Installing Support Feet (See gure 11.)

1. Lay heater onto table on its back with bottom

edge overhanging table edge.

2. Securely attach feet to bottom of heater using

2 – self-tapping screws each.

Figure 11

Note: Feet should have long end going out the

front of heater, and the edge coinciding with side of

heater. If feet overhang side of the heater, switch

leg location.

3. Place heater on non-combustible surface (see

Locating Heater, page 6) before proceeding

with gas connection. If this will be a permanent

location, heater may be locked into position

using anchoring holes in mounting feet.

Note: Use of oor mounting feet will require

you to use a 3/8 NPT street elbow to make gas

connection.

CONNECTING TO GAS SUPPLY

WARNING: A qualied service person must connect

heater to gas supply. Follow all local codes.

WARNING: This appliance requires a 3/8” NPT

(National Pipe Thread) inlet connection to the

pressure regulator. Use of oor mounting feet will

require you to use a 3/8 NPT street elbow to make

gas connection.

CAUTION: Never connect heater directly to the

Propane supply. This heater requires an external

regulator.(which is attached to the supplied hose).

Install the external regulator between the heater and

Propane/LP supply.

The external regulator will reduce the incoming gas

pressure to between 11 and 14 inches of water. If

you do not reduce incoming gas pressure heater

regulator damage could occur. Install external

regulator with the vent pointing down. Pointing the

vent down protects it from freezing rain or sleet.

CAUTION: Use only new black iron or steel pipe.

Internally-tinned copper tubing may be used in certain

areas. Check your local codes. Use pipe of larger

enough diameter to allow proper gas volume to heater.

If pipe is too small, undue loss of pressure will occur.

Installation must include an equipment shuto valve,

union and plugged 1/8” NPT tap. Locate NPT tap within

reach of test gauge hookup. NPT tap must be upstream

from heater (see gure 12).

*A CSA/AGA certied equipment shuto valve with

1/8” NPT tap is an acceptable alternative to test gauge

connection. Purchase the CSA/AGA certied equipment

shuto valve from your dealer.

IMPORTANT: Install an equipment shuto valve in an

accessible location. The equipment shuto valve is for

turning on or shutting o the gas to the appliance.

Apply pipe joint sealant lightly to male threads. This will

prevent excess sealant from going into pipe. Excess

sealant in pipe could result in clogged heater fuel train.

CAUTION: Use pipe joint sealant that is resistant to LP-Gas.

Install sediment trap in supply line as shown in gure

12. Locate sediment trap where it is within reach

for cleaning. A sediment trap traps moisture and

contaminants. This keeps them from going into heater.

If sediment trap is not installed or is installed improperly,

heater may not run correctly.

IMPORTANT: Hold pressure regulator with wrench

when connecting it to gas piping and/or ttings.

CHECKING GAS CONNECTIONS

WARNING: Test all gas piping and connections for

leaks after installing or servicing. Correct all leaks

at once.

Screw

hole

Screw

hole

9Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

WARNING: Never use an open ame to check for

a gas leak. Apply a mixture of liquid soap and water

to all joints. Bubbles forming show a leak. Correct

all leaks at once.

PRESSURE TESTING GAS SUPPLY PIPING

SYSTEM

High Pressure

Test pressure in Excess of ½ psig (3.5kPa)

1. Disconnect appliance with its appliance main

gas valve (control valve) and equipment shuto

valve from gas supply piping system. Pressures

in excess of ½ psig will damage heater regulator.

2. Cap o open end of gas pipe where equipment

shuto valve was connected.

3. Pressurize supply piping system by either using

compressed air or opening main gas valve on

or near gas meter.

4. Check all connections and joints in gas supply

piping system. Apply mixture of liquid soap and

water to gas joints. Bubbles forming show a

leak.

5. Correct all leaks at once.

6. Depressurize and relieve pressure in supply

piping system.

7. Reconnect heater and equipment shuto valve

to gas supply.

8. Reconnected ttings must be checked for leaks

in next section.

Low Pressure

Test Pressure Equal To or Less Than ½ psig (3.5 kPa)

1. Close equipment shuto valve (see gure 12).

2. Pressurize supply piping system by either using

compressed air or opening propane/LP supply

valve.

3. Check all joints from the propane/LP supply

valve to equipment shuto valve (see gure

13). Apply mixture of liquid soap and water to

gas joints. Bubbles forming show a leak.

4. Correct all leaks at once.

5. Depressurize and relieve pressure from supply

piping system.

Pressure Testing Heater Gas Connections:

1. Make sure that the heater supply piping sys-

tem is connected and has been leak tested as

described above.

2. Make sure control knob of heater is in OFF

position.

3. Open equipment shuto valve (see gure 12).

4. Open propane/LP supply valve.

5. Check all joints from equipment shuto valve

to control valve (see gure 13). Apply mixture

of liquid soap and water to gas joints. Bubbles

forming show a leak.

6. Correct all leaks at once.

7. Light heater (see Operating Your Heater, page 10)

8. Turn o heater (see To Turn OFF Gas to

Appliance, page 10.)

9. Replace lower front panel.

Equipment

Shuto Valve

Open

Closed

FIGURE 12

FIGURE 13

FIGURE 14

Nipple

Tee Joint

Cap

Shutoff Valve

HEATER CABINET

Nipple

Tee Joint

Ground Joint Union

3/8” NPT Pipe Nipple

Pressure

Regulator

Test Gauge

Connection

1/8” NPT Plug Tap

Reducer Bushing

to 1/8” NPT

Nipple

Sediment

Trap

3” minimum

Fuel line from

Regulated LP Tank

(11”W.C to 14” WC Pressure)

10 Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

OPERATING YOUR HEATER

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions

exactly, a re or explosion may result causing

property damage, personal injury or loss of life.

A. This appliance has a pilot that must be lighted

by hand. When lighting the pilot, follow these

instructions exactly.

B. BEFORE LIGHTING smell all around the

appliance area for gas. Be sure to smell next to

the oor because some gas is heavier than air

and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

• Shut o gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call you gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you can not reach your gas supplier, call the re

department.

• Use only your hand to push in or turn the gas con-

trol knob. Never use tools. If knob will not push in or

turn by hand, don’t try to repair it; call

a qualied service technician or gas supplier. Force

or attempted repair may result in a re or explosion.

• Do not use this appliance if any part has been

underwater. Immediately call a qualied service

technician to inspect the appliance and to replace

any part of the control system which has been

underwater.

LIGHTING INSTRUCTIONS

1. STOP! Read the all safety information included with

and on the side of heater.

2. Check that gas supply to heater is on.

3. Push in gas control knob and slightly turn clockwise

to the OFF position (see gure 14).

Note: Knob cannot be turned from PILOT to OFF

unless knob is pushed in slightly. Do not force.

4. Wait ve (5) minutes to clear out any gas. Then smell

for gas, including near the oor. If you smell gas,

STOP! Follow “B” in the safety information above. If

you do not smell gas, go to the next step.

5. Push in gas control know slightly and turn

counterclockwise to PILOT/IGN and

depress for ve (5) seconds.

Note: The rst time that the heater is operated after

connecting the gas supply, the control knob should

be depressed for about 30 seconds. This will allow

air to bleed from the gas system.

6. Push in control knob and rotate control

knob back to OFF position then rotate

counterclockwise to PILOT/IGN position.

This will light pilot. If needed gently keep

rotating control knob back and forth while

depressed until pilot lights.

7. Keep control knob depressed in for ten (10)

seconds after lighting pilot. If pilot goes out,

repeat steps 4, 5, 6 and 7.

If pilot does not stay lit, refer to

Troubleshooting, pages 12-13. Also, contact

a qualied service person or gas supplier for

repairs.

If control knob does not pop up when released,

contact a qualied service person or gas

supplier for repairs.

8. When the pilot is lit, turn the control knob

counterclockwise to heating level. The main

burner should light.

9. To select the desired heat level, turn the

temperature setting knob to desired comfort

setting from 1 to 5.

CAUTION: Do not try to adjust heating level by using

equipment shuto valve.

TO TURN OFF GAS TO APPLIANCE

SHUTTING OFF HEATER:

1. Turn o equipment shuto valve.

2. Turn control knob clockwise to the OFF

position.

SHUTTING OFF BURNER ONLY (PILOT STAYS LIT)

1. Turn control knob clockwise to the PILOT/

IGN position.

INSPECTING BURNER

Check pilot ame pattern and burner ame pattern

often.

PILOT FLAME PATTERN

Figure 16 shows a correct pilot ame pattern and

incorrect pilot ame pattern. The incorrect pilot ame

pattern is not touching thermocouple. This will cause

the thermocouple to cool. When the thermocouple

cools, the heater will shut down. If pilot ame pattern is

incorrect, as shown in Figure 16:

Ignitor Button Control Knob

Figure 15

11 Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

• Turn heater o (see To Turn OFF Gas to

Appliance, page 10)

• See Troubleshooting, pages 12-13.

CLEANING AND MAINTENANCE

WARNING: Turn o heater and let cool before

servicing.

CAUTION: You must keep control areas, burner and

circulation air passageways of heater clean. Inspect

these areas of heater before use. Have the heater

inspected yearly by a qualied service person. Heater

may need more frequent cleaning due to excess lint

from carpeting, bedding material, pet hair, etc.

Make sure grille guard is in place before running

heater. If screen or grille guard is removed for servicing

it must be replaced prior to operating the heater.

WARNING: Failure to keep the primary air

opening(s) of the burner(s) clean may result in

sooting and property damage.

CLEANING ODS/PILOT AND BURNER

• Use as vacuum cleaner, pressurized air or

small soft bristled brush to clean.

CLEANING BURNER PILOT AIR HOLE INLET

We recommend that you clean the unit every 2,500

hours of operation or every three months. We also

recommend that you keep the burner tube and pilot

assembly clean and free of dust and dirt. To clean these

parts we recommend using compressed air no greater

than 30 psig.

This can be done by using a vacuum cleaner in the

blow position or using compressed air in a can. If

using canned air please follow the directions on the

can. If you don’t follow directions on the can you could

damage the burner or pilot assembly. In addition, the

directions below should also be followed.

1. Shut o the unit, including the pilot. Allow the

unit to cool for at least thirty minutes.

2. Inspect burner and pilot for dust and dirt.

3. Blow air through the port/slots and holes in the

burner.

Figure 16

Correct pilot position. Incorrect pilot position.5

Pilot Air Inlet Hole

Pilot Assembly

Figure 17

A yellow tip on the pilot ame indicates dust and dirt in

the pilot assembly. To clean the pilot assembly nd the

small pilot air inlet hole about two inches from where

the pilot ame comes out of the pilot assembly (see

Figure 17). With the unit o, lightly blow air through the

air inlet hole. You may blow through a drinking straw if

compressed air is not available.

CLEANING HEATER CABINET

Air passageways

• Use a vacuum cleaner or pressurized air to

clean

Exterior

• Use a soft cloth dampened with a mild soap

and water mixture. Wipe the cabinet to remove

dust.

12 Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

TROUBLESHOOTING

NOTE: All troubleshooting items are listed in order of operation and likely occurrence.

WARNING: Only a qualied service person should service and repair heater.

CAUTION: Never use a wire needle, or similar object to clean ODS/pilot. This can damage ODS/pilot unit.

Make sure grille guard is in place before running heater. If screen or grille guard is removed for servicing it must be

replaced prior to operating the heater.

TROUBLESHOOTING

WARNING: If you smell gas:

• Shut o gas supply

• Do not try to light any appliance

• Do not touch any electrical switch; do not use any phone in your building

• Immediately call you gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning supplies, paint, paint

remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with

combustion air and create odors and possible discoloration of walls and ceilings.

OBSERVED SYMPTOM POSSIBLE CAUSE REMEDY

When ignitor button is pressed in, there is a

spark at the ODS/pilot but no ignition

1. Control knob not fully pressed in.

2. Control knob not pressed in long enough

3. Equipment shuto valve not fully open

4. Thermocouple connection loose at control valve

5. Pilot ame not touching thermocouple, which allows

thermocouple to cool, causing pilot ame to go out.

This problem could be caused by one or both of the

following:

a. Low gas pressure

b. Dirty or partially clogged ODS/pilot

6. Thermocouple damaged

7. Control valve damaged

1. Press in control knob fully

2. After ODS/pilot lights, keep control knob pressed in

for 30 seconds

3. Fully open equipment shuto valve

4. Hand tighten thermocouple nut until snug, and then

tighten 1/4 turn more.

5. -

a. Contact local gas company

b. Clean ODS/pilot (see Cleaning and Maintenance,

page 11).

6. Replace thermocouple

7. Replace Control valve.

Burner does not light after ODS/pilot is lit 1. Burner orice is clogged

2. Burner orice diameter to small

3. Inlet gas pressure is too low

1. Clean burner orice (see Cleaning and Maintenance

on page 11), or replace burner orice

2. Replace burner orice

3. Contact local gas company

Delayed ignition of burner 1. Manifold pressure is too low

2. Burner orice is clogged

1. Clean burner orice (see Cleaning and Maintenance

on page 11), or replace burner orice

Burner backring during operation 1. Burner orice is clogged or damaged

2. Burner damaged

3. Gas regulator defective

1. Clean burner orice (see Cleaning and Maintenance

on page 11), or replace burner orice

2. Replace burner

3. Replace gas regulator

Burner plaque(s) does not glow [Infrared

Only]

1. Plaque damaged

2. Control knob set between locked positions.

3. Inlet gas pressure is too low

1. Replace burner

2. Turn control knob until it locks at desired setting.

3. Replace gas regulator

Slight smoke or odor during initial operation 1. Residues from manufacturing process 1. Problem will stop after a few hours of operation

Heater produces a whistling noise when

burner is lit

1. Turning control knob to HI position when burner is cold

2. Air in gas line

3. Air passageways on heater blocked

4. Dirty or partially clogged burner orice.

1. Turn control knob to LO position and let warm up for

a minute.

2. Operate burner until air is removed from line have

gas line checked by local gas company.

3. Observe minimum installation clearances (see Figure

4 page 6)

4. Clean burner orice (see Cleaning and Maintenance

on page 11), or replace burner orice.

White powder residue forming within burner

box or on adjacent walls or furniture

1. When heated, vapors from furniture polish, wax, carpet

cleaners, etc., turn into white powder residue

1. Turn heater o when using furniture polish, wax,

carpet cleaner or similar products.

Heater produces unwanted odors. 1. Heater burning vapors from paint, hair spray, glues, etc.

See IMPORTANT statement above

2. Gas leak. See WARNING statement at top of page.

1. Ventilate room. Stop using odor-causing products

while heater is running.

2. Locate and correct all leaks (see Checking Gas

Connections, page 9)

13 Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

Heater shuts o in use (ODS operates) 1. Not enough fresh air is available

2. Low line pressure

3. ODS/pilot is partially clogged

1. Open window and/or door for ventilation

2. Contact local gas company

3. Clean ODS/pilot (see Cleaning and Maintenance,

page 11)

Gas odor even when control knob is in OFF

position

1. Gas leak. See WARNING statement at top of page

2. Control valve is defective

1. Locate and correct all leaks (see Checking Gas

Connections, page 9)

2. Replace control valve

Gas odor during combustion 1. Foreign matter between control valve and burner

2. Gas leak. See WARNING statement at top of page

1. Take apart gas tubing and remove foreign matter

2. Locate and correct all leaks (see Checking Gas

Connections, page 9)

Heater produces a clicking/ticking noise just

after burner is lit or shut o

1. Metal expanding while heating or contracting while

cooling

1. This is common with most heaters. If noise is

excessive, contact qualied service person

Moisture/condensation noticed on windows 1. Not enough combustion/ventilation air 1. Refer to Fresh Air for Combustion and Ventilation

page 3 through 5.

OBSERVED SYMPTOM POSSIBLE CAUSE REMEDY

14 Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

MODEL: HSSVFBF10LPT

ITEM P/N PART DESCRIPTION QTY ITEM P/N PART DESCRIPTION QTY

1 80040 Wire Guard 1 14 80058 Floor Mounting Feet 1

2 80051 Front Panel 1 15 80052 Back Panel 1

3 80038 Glass 1 16 80036 Wall Mounting Bracket 1

4 80024 Reflector 1 17 N/A Heat Shield 1

5 80026 Reflector Back Panel 1 18 N/A Back Heat Shield 1

6 N/A Burner Left Bracket 1 19 70640 Thermostat Valve 1

7 80056 ODS Pilot Assembly w/ Thermocouple (LP) 1 20 80019 Igniter Module 1

8 80017 Burner Assembly 1 21 80014 Igniter Wire 1

9 80009-01 Orifice 1 22 80011 Igniter Module Mounting Bracket 1

10 N/A Burner Right Bracket 1 23 80010 Thermostat Valve Mounting Bracket 1

11 80078 Regulator 1 24 80034 Glass Bracket 1

12 80055 Regulator Mounting Bracket 1 ** 70342 Hardware Kit (not shown) 1

13 80020 Regulator Connection 1

910 11

PARTS LIST AND DIAGRAM

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specically approved with this

heater may result in property damage or personal injury.

15 Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specically approved with this

heater may result in property damage or personal injury.

MODEL: HSSVFRD10LPT

ITEM P/N PART DESCRIPTION QTY ITEM P/N PART DESCRIPTION QTY

1 80040 Wire Guard 1 11 80058 Floor Mounting Feet 1

2 80051 Front Panel 1 12 80052 Back Panel 1

3 80022 Reflector 1 13 80036 Wall Mounting Bracket 1

4 80115 Burner Assembly 1 14 N/A Heat Shield 1

5 80056 ODS Pilot Assembly w/ Thermocouple (LP) 1 15 N/A Back Heat Shield 1

6 N/A ODS Bottom Bracket 1 16 70640 Thermostat Valve 1

7 N/A Fireproof Plate 1 17 80019 Ignitoe Module 1

8 80078 Regulator 1 18 80014 Igniter Wire 1

9 80055 Regulator Mounting Bracket 1 ** 70342 Hardware Kit (not shown) 1

10 80020 Regulator Connection 1 ** 80009-01 Orifice (not shown) 1

PARTS LIST AND DIAGRAM

HSSVFBF10LPT

HSSVFRD10LPT

OPERATING INSTRUCTIONS

AND OWNER’S MANUAL

READ INSTRUCTIONS CAREFULLY: Read and follow all instructions. Place instructions in a safe

place for future reference. Do not allow anyone who has not read these instructions to assemble,

light, adjust or operate the heater.

Model #

Heatstar Products, Inc. reserves the right to make changes at any time, without notice

or obligation, in colors, specifications, accessories, materials and models.

WARNING:

USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS

COULD CAUSE INJURY OR DEATH. REPLACEMENT PARTS ARE ONLY AVAILABLE

DIRECT FROM THE FACTORY AND MUST BE INSTALLED BY A QUALIFIED SERVICE

AGENCY.

REPLACEMENT PARTS ORDERING INFORMATION:

PURCHASING: Accessories may be purchased at any Heatstar Products local dealer

or direct from the factory

FOR INFORMATION REGARDING SERVICE

Please call Toll-Free 866-447-2194

WWW.HEATSTARBYENERCO.COM

Our office hours are 8:00 AM – 5:00 PM, EST, Monday through Friday.

Please include the model number, date of purchase, serial number and description

of problem in all communication.

LIMITED WARRANTY

Enerco Group, Inc. (EGI) warrants Heatstar Vent free heaters to be free from defects

in material and workmanship for a period of five years from the date of manufacture.

• During the first two years, EGI will repair or replace this product if it is proven to

be defective within the first two years and it is returned at customer expense with

proof of purchase to the location of EGI’s choice. EGI will be the sole judge of what

is determined to be a defect.

• In year’s three to five, EGI will provide replacements for defective parts to the

customer free of charge.

This warranty gives you specific legal rights, and you may also have other rights which

vary from state to state.

HEATSTAR, INC., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 866-447-2194

HEATSTAR is a registered trademarks of Heatstar Products, Inc.

PRODUCT REGISTRATION: Thank you for your purchase.

Please log in to http://www.egiregistration.com to register your product.

HeatStar HSSVFB30NGBT Owner's manual

Brand: HeatStar

Model: HSSVFB30NGBT

Category: Space heaters

Type: Owner's manual

Download PDF

report

HeatStar HSSVFB30NGBT Owner's manual

HeatStar HSSVFB30NGBT Owner's manual

Related papers

Other documents