ML Accessories LEDFRA9 User manual

Brand: ML Accessories

Model: LEDFRA9

Type: User manual

INSTALLATION & MAINTENANCE MANUAL

LEDFRA9

These instructions should be read carefully and retained after installation by the end user for

future reference and maintenance.

These instructions should be used to aid installation of the following product:

LEDFRA9

GENERAL INSTRUCTIONS

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)

and current Building Regulations. If in any doubt, consult a qualified electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this product is fitted) does not exceed the rating of the

circuit cable, fuse, or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

• Do not overload this accessory or subject it to conditions outside its rating

• This product is Class III

• This product is IP20 rated

SAFETY

INSTALLATION

• Provide power to the required point of installation

• Position controller inbetween the LED driver and LED flex

• Ensuring correct polarity is observed, connect the secondary side of the LED driver to the primary side of the

LED controller [(+ Red) (- Black)] (see Fig. 1)

• Terminate the 12V or 24V LED flex to the secondary side of the controller: the positive from the LED flex to

V+, Red to R, Green to G and Blue to B (see Fig. 1)

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid installation of the following product:

LEDFRA9

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this product is fitted) does not exceed the rating of

the circuit cable, fuse, or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

• Do not overload this accessory or subject it to conditions outside its rating

• This product is Class III

• This product is IP20 rated

INSTALLATION

• Provide power to the required point of installation

• Position controller inbetween the LED driver and LED flex

• Ensuring correct polarity is observed, connect the secondary side of the LED driver to the primary side

of the LED controller [(+ Red) (- Black)] (see Fig. 1)

• Terminate the 12V or 24V LED flex to the secondary side of the controller: the positive from the LED

flex to V+, Red to R, Green to G and Blue to B (see Fig. 1)

Fig. 1

• Ensure the LED flex does not exceed the maximum wattage of the controller

12V LED flex – up to 72W

24V LED flex – up to 144W

• Switch on and check for correct operation

Note – This product is able to operate at either 12V or 24V. The appropriate driver output voltage should be

selected to match the input voltage requirements of the LED load

Fig. 1

• Ensure the LED flex does not exceed the maximum wattage of the controller

12V change wattage to 216W

24V change wattage to 432W

• Switch on and check for correct operation

Note – This product is able to operate at either 12V or 24V. The appropriate driver output voltage should be

selected to match the input voltage requirements of the LED load

Note – The remote requires 3 x AAA batteries (not included).

REMOTE INTERFACE

Note – The remote requires 3 x AAA batteries (not included).

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance

testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the

product.

This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities

for where facilities exist.

WARRANTY

This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance with

the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will

invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of

purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation

costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve

the right to alter product specification without prior notice.

12V, 24V IP20, Class III, indoor only

AVDEC21_V1

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance

testing. Irreparable damage will occur if this instruction is not followed. .

GENERAL

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the

product.

This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities

for where facilities exist.

WARRANTY

This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance with

the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will

invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place

of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation

costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve

the right to alter product speciﬁcation without prior notice.

Manufacturers Declaration of Conformity

For ML Accessories (Knightsbridge)

Electrical products in accordance with CE marking

ML Accessories Ltd. Declare that all products have been designed, manufactured, and tested in

accordance with the requirements of the relevant legislation

CE marking legislation

In Accordance with the following Directives:

2014/35/EU Low Voltage Directive

2014/30/EU EMC Directive

2014/53/EU Radio Equipment Directive

Including Legislation

1907/2006 REACH

2015/863 RoHS

2021/341 ERP

Safety Standards

Full individual declarations and speciﬁc safety standards applicable to relevant product series can be found on

our website www.mlaccessories.co.uk

We hereby declare that the equipment named above has been designed to comply with the relevant

sections of the above referenced speciﬁcations. The product complies with all essential requirements of

the directives.

Scott Brewer Catherine Connolly

Technical Manager CEO

ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable. Bedfordshire, LU5 4LT

This declaration becomes invalid if technical or operational modiﬁcations are introduced without ML Accessories Ltd. written consent.

Manufacturers Declaration of Conformity

For ML Accessories (Knightsbridge)

Electrical products in accordance with UKCA marking

ML Accessories Ltd. declare that all products have been designed, manufactured, and tested in

accordance with the requirements of the relevant legislation

UKCA marking legislation

UK SI 2016 No. 1091 Electro Magnetic Compatibility Regulations 2016

UK SI 2016 No. 1101 The Electrical Equipment (Safety) Regulations 2016

UK SI 2012 No. 3032 Restriction of the use of Certain Hazardous Substances in Electrical and

Electronic Equipment Regulations 2012

UK SI 2017 No. 1206 Radio Equipment regulations 2017

UK SI 2021 No. 1095 The Ecodesign for Energy-Related Products and Energy

Information (Lighting Products) Regulations 2021

Included Legislation

UK SI 2008 No. 2852 UK REACH

UK SI 2013 No. 3113 WEEE

Safety Standards

Full individual declarations and speciﬁc safety standards applicable to relevant product series can be found on

our website www.mlaccessories.co.uk

We hereby declare that the equipment named above has been designed to comply with the relevant

sections of the above referenced speciﬁcations. The products comply with all essential requirements of

the directives.

Scott Brewer Catherine Connolly

Head of Technical CEO

ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable. Bedfordshire, LU5 4LT

This declaration becomes invalid if technical or operational modiﬁcations are introduced without ML Accessories Ltd. written consent.

ML Accessories Limited LU5 4LT

www.mlaccessories.co.uk

AVJUL22_V2

Supplied By:

(UK) Manufacturer

ML Accessories Ltd, Unit E Chiltern Park, Boscombe Road, Dunstable LU5 4LT,

www.mlaccessories.co.uk

(EU) Authorised Representative

nnuks Holding GmbH, Niederkasseler Lohweg 18,

40547 Düsseldorf, Germany,

Email: [email protected]om

ML Accessories LEDFRA9 User manual

ML Accessories LEDFRA9 User manual

ML Accessories LEDFRA9 User manual

Related papers

Other documents