Foosball Table Assembly
Table arrives assembled as
shown.
Step 1 Level table.
A leveling wrench is
included with table.
Alway adjust the low side of the
table rst
Use wrench to level table left and
right. Adjust each leg until level.
Note: turning the wrench to the
left raises the table. Turning right
lowers the table.
View of stainless leveler
Note the load levelers have a
cleats to prevent shifting during
the leveling process.
Foosball parts shown laid out in
packing box.
Step 2 Layout parts on table as
shown: Goalie, 2 man, 5 man and
3 man front. Handles will be on
the right side as shown.
Handles on left side for blue men.
Step 3 Place man on goalie rod. (Rod has 3
holes) As shown. Washer, bumper, shaft collar,
goalie, shaft collar, bumper and
washer.
Note 3 man goal will not include the shaft col-
lars. Men will replace collars.
Step 4 Install 2 man rod.
Repeat: Washer, bumper, man, man,
bumper and washer.
This is the same for all rods except
the goalie rods.
Step 5 Install 5 Man Rod.
(5 Man rod sequence shown)
Step 6 Install 3 man offensive front men.
Step 7 Place blue men on rods.
Goalie, 2 man, 5 man and 3 man front
(offense).
Note place men on rods
with hole facing opposing
goal.
2 Man Rod
Two holes
in rod
1 Man Rod
Three holes
in rod
5 Man Rod
Five holes
in rod
Foosball Table Assembly
FT543236-1
One-Man Goal with Sloped Corners
Rubber Bumper
Stainless Steel Rod Coupler
Plastic Washer
Securing the stainless steel couplers.
Align the large hole in the coupler with the
outside hole on the rod. Insert the 8-32 x 1 1/2”
security bolt. Thread nylon locknut on bolt and
tighten.
See enlarged illustration below.
2 Man Rod
Two holes
in rod
3 Man Rod
Three holes
in rod
5 Man Rod
Five holes
in rod
1 Man Rod
Three holes
in rod
3 Man Rod
Three holes
in rod
Page 2
Hole in rod
Stainess Coupler
8-32 x 1 1/2”
screw with nut
Page 3
2 Man Rod
Two holes
in rod
3 Man Rod
Three Holes
in rod
5 Man Rod
Five Holes
in rod
Foosball Table Assembly
FT543236-3
Three-Man Goal with at Corners
Rubber Bumper
Plastic Washer
5 Man Rod
Five Holes
in rod
3 Man Rod
Three Holes
in rod
3 Man Rod
Three Holes
in rod
3 Man Rod
Three Holes
in rod
2 Man Rod
Two holes
in rod
Step 11 Place rubber caps on
each rod end.
Foosball table assembled.
PLAY AND HAVE FUN!
Step 8 Assemble the goalie rod.
Align shaft collar hole in rod. Insert 8-32 x
1 1/2” screw and thread nylon locknut on
screw. Tighten.
Repeat with second shaft collar.
Step 9 Man assembly.
Place the 8-32 x 1 1/4” Phillips head screw
into front side of man. Align with hole in rod.
Place the 8-32 nut on the back side. Begin
threading screw into nut.
Step 10 Tighten screw. Using the screw-
driver included tighten screw until snug.
DO NOT OVER TIGHTEN
USE HAND TOOLS ONLY.
Repeat for each rod until complete.
Foosball Table Rod Assembly Page 4
8-32 x 1 1/4” assembly screw and nut
Security phillips screw shown
8-32 Hex nylon lock nut shown
/
