Anova FT543236-1 Installation guide

Brand: Anova

Model: FT543236-1

Type: Installation guide

Anova FT543236-1 is a foosball table that comes assembled and ready to play. It features a one-man goal with sloped corners and a three-man goal with flat corners. The table is also equipped with stainless steel rods and couplers, as well as rubber bumpers and plastic washers. The handles are located on the right side for the red men and on the left side for the blue men. With its durable construction and easy assembly, the Anova FT543236-1 foosball table is perfect for hours of endless fun and competition.

Foosball Table Assembly

Table arrives assembled as

shown.

Step 1 Level table.

A leveling wrench is

included with table.

Alway adjust the low side of the

table rst

Use wrench to level table left and

right. Adjust each leg until level.

Note: turning the wrench to the

left raises the table. Turning right

lowers the table.

View of stainless leveler

Note the load levelers have a

cleats to prevent shifting during

the leveling process.

Foosball parts shown laid out in

packing box.

Step 2 Layout parts on table as

shown: Goalie, 2 man, 5 man and

3 man front. Handles will be on

the right side as shown.

Handles on left side for blue men.

Step 3 Place man on goalie rod. (Rod has 3

holes) As shown. Washer, bumper, shaft collar,

goalie, shaft collar, bumper and

washer.

Note 3 man goal will not include the shaft col-

lars. Men will replace collars.

Step 4 Install 2 man rod.

Repeat: Washer, bumper, man, man,

bumper and washer.

This is the same for all rods except

the goalie rods.

Step 5 Install 5 Man Rod.

(5 Man rod sequence shown)

Step 6 Install 3 man offensive front men.

Step 7 Place blue men on rods.

Goalie, 2 man, 5 man and 3 man front

(offense).

Note place men on rods

with hole facing opposing

goal.

2 Man Rod

Two holes

in rod

1 Man Rod

Three holes

in rod

5 Man Rod

Five holes

in rod

Foosball Table Assembly

FT543236-1

One-Man Goal with Sloped Corners

Rubber Bumper

Stainless Steel Rod Coupler

Plastic Washer

Securing the stainless steel couplers.

Align the large hole in the coupler with the

outside hole on the rod. Insert the 8-32 x 1 1/2”

security bolt. Thread nylon locknut on bolt and

tighten.

See enlarged illustration below.

2 Man Rod

Two holes

in rod

3 Man Rod

Three holes

in rod

5 Man Rod

Five holes

in rod

1 Man Rod

Three holes

in rod

3 Man Rod

Three holes

in rod

Page 2

Hole in rod

Stainess Coupler

8-32 x 1 1/2”

screw with nut

Page 3

2 Man Rod

Two holes

in rod

3 Man Rod

Three Holes

in rod

5 Man Rod

Five Holes

in rod

Foosball Table Assembly

FT543236-3

Three-Man Goal with at Corners

Rubber Bumper

Plastic Washer

5 Man Rod

Five Holes

in rod

3 Man Rod

Three Holes

in rod

3 Man Rod

Three Holes

in rod

3 Man Rod

Three Holes

in rod

2 Man Rod

Two holes

in rod

Step 11 Place rubber caps on

each rod end.

Foosball table assembled.

PLAY AND HAVE FUN!

Step 8 Assemble the goalie rod.

Align shaft collar hole in rod. Insert 8-32 x

1 1/2” screw and thread nylon locknut on

screw. Tighten.

Repeat with second shaft collar.

Step 9 Man assembly.

Place the 8-32 x 1 1/4” Phillips head screw

into front side of man. Align with hole in rod.

Place the 8-32 nut on the back side. Begin

threading screw into nut.

Step 10 Tighten screw. Using the screw-

driver included tighten screw until snug.

DO NOT OVER TIGHTEN

USE HAND TOOLS ONLY.

Repeat for each rod until complete.

Foosball Table Rod Assembly Page 4

8-32 x 1 1/4” assembly screw and nut

Security phillips screw shown

8-32 Hex nylon lock nut shown

Anova FT543236-1 Installation guide

Anova FT543236-1 Installation guide

Anova FT543236-1 Installation guide

Other documents