Pepperl+Fuchs LTC57 Operating instructions

ISO9001

3

Pulscon LTC57

PROFIBUS PA

Guided Level Radar

Level measurement in bulk solids

PROCESS AUTOMATION

QUICK START GUIDE

With regard to the supply of products, the current issue of the following document is

applicable: The General Terms of Delivery for Products and Services

of the Electrical Industry, published by the Central Association of the Electrical Industry

(Zentralverband Elektrotechnik und Elektroindustrie (ZVEI) e.V.) in its most recent

version as well as the supplementary clause: "Expanded reservation of proprietorship"

Pulscon LTC57 PROFIBUS PA

These Instructions are Quick Start Guides; they are not a substitute for the Operating

Instructions pertaining to the device.

Detailed information about the device can be found in the Operating Instructions and the other

documentation via internet www.pepperl-fuchs.com.

The complete device documentation consists of:

• these Quick Start Guide

• the Operating Instructions

• the Technical Information

Pulscon LTC57 PROFIBUS PA

Content

274505 2015-04

3

Pulscon LTC50 HART

1 Important document information . . . . . . . . . . . . . . . . . . . 5

1.1 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Basic safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.1 Requirements for the personnel. . . . . . . . . . . . . . . . . . . . . . . . . 8

2.2 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 Workplace safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.5 Product safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3 Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.1 Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4 Incoming acceptance and product identification. . . . . 13

4.1 Incoming acceptance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.2 Product identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.3 Device documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5 Storage, Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.1 Storage conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.2 Transport product to the measuring point . . . . . . . . . . . . . . . 16

6 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

6.1 Mounting requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

6.2 Mounting the device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

6.3 Post-installation check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

7 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

7.1 Connection conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

7.2 Connecting the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

7.3 Post-connection check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

274505 2015-04

4

Pulscon LTC57 PROFIBUS PA

Content

8 Integration into a PROFIBUS network . . . . . . . . . . . . . . 44

8.1 Overview of the device database files (GSD) . . . . . . . . . . . . . 44

8.2 Set device address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

9 Commissioning (via operating menu) . . . . . . . . . . . . . . 46

9.1 Display and operating module . . . . . . . . . . . . . . . . . . . . . . . . . 46

9.2 Operating menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

9.3 Unlock the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

9.4 Setting the operating language . . . . . . . . . . . . . . . . . . . . . . . . 50

9.5 Configuration of a level measurement. . . . . . . . . . . . . . . . . . . 51

9.6 User-specific applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Pulscon LTC57 PROFIBUS PA

Important document information

274505 2015-04

5

1 Important document information

1.1 Symbols

1.1.1 Used Symbols

This document contains information that you must read for your own personal

safety and to avoid property damage. Depending on the risk level, the warning

messages are displayed in descending order as follows:

Safety-Relevant Symbols

Informative Symbols

Action

This symbol indicates a paragraph with instructions.

Danger!

This symbol indicates an imminent danger.

Non-observance will result in personal injury or death.

Warning!

This symbol indicates a possible fault or danger.

Non-observance may cause personal injury or serious property damage.

Caution!

This symbol indicates a possible fault.

Non-observance could interrupt the device and any connected systems and

plants, or result in their complete failure.

Note!

This symbol brings important information to your attention.

Pulscon LTC57 PROFIBUS PA

274505 2015-04

6

Pulscon LTC57 PROFIBUS PA

Important document information

1.1.2 Electrical symbols

1.1.3 Tool symbols

Symbol Meaning

Direct current

A terminal to which DC voltage is applied or through which direct

current flows.

Alternating current

A terminal to which alternating voltage is applied or through which

alternating current flows.

Direct current and alternating current

• A terminal to which alternating voltage or DC voltage is

applied.

• A terminal through which alternating current or direct current

flows.

Ground connection

A grounded terminal which, as far as the operator is concerned, is

grounded via a grounding system.

Protective ground connection

A terminal which must be connected to ground prior to

establishing any other connections.

Equipotential connection

A connection that has to be connected to the plant grounding

system: This may be a potential equalization line or a star

grounding system depending on national or company codes of

practice.

Table 1.1

)

*

Symbol Meaning

Torx screwdriver

Flat blade screwdriver

Cross-head screwdriver

Allen key

Hexagon wrench

Table 1.2

Pulscon LTC57 PROFIBUS PA

Important document information

274505 2015-04

7

1.1.4 Symbols for certain types of information

1.1.5 Symbols in graphics

1.1.6 Symbols at the device

Symbol Meaning

Allowed

Indicates procedures, processes or actions that are allowed.

Preferred

Indicates procedures, processes or actions that are preferred.

Forbidden

Indicates procedures, processes or actions that are forbidden.

1., 2., 3. ... Series of steps

Result of a sequence of actions

Visual check

Table 1.3

Symbol Meaning

1, 2, 3 ... Item numbers

Series of steps

A, B, C, ... Views

A-A, B-B, C-C, ... Sections

Hazardous area

Indicates a hazardous area.

Safe area (non-hazardous area)

Indicates a non-hazardous location.

Table 1.4

,…

,1. 2. 3.

-

.

Symbol Meaning

Safety instructions

Observe the safety instructions contained in the associated

Operating Instructions.

Temperature resistance of the connection cables

Specifies the minimum value of the temperature resistance of the

connection cables.

Table 1.5

274505 2015-04

8

Pulscon LTC57 PROFIBUS PA

Basic safety instructions

2 Basic safety instructions

2.1 Requirements for the personnel

The personnel for installation, commissioning, diagnostics and maintenance must

fulfill the following requirements:

• Trained, qualified specialists must have a relevant qualification for this

specific function and task

• Are authorized by the plant owner/operator

• Are familiar with federal/national regulations

• Before beginning work, the specialist staff must have read and understood

the instructions in the Operating Instructions and supplementary

documentation as well as in the certificates (depending on the application)

• Following instructions and basic conditions

The operating personnel must fulfill the following requirements:

• Being instructed and authorized according to the requirements of the task by

the facility's owner-operator

• Following the instructions in these Operating Instructions

2.2 Designated use

Application and measured materials

The measuring device described in these Operating Instructions is intended only

for level measurement of bulk solids. Depending on the version ordered the

device can also measure potentially explosive, flammable, poisonous and

oxidizing materials.

Observing the limit values specified in the "Technical data" and listed in the

Operating Instructions and supplementary documentation, the measuring device

may be used for the following measurements only:

• Measured process variable: Level

• Calculated process variables: Volume or mass in arbitrarily shaped vessels

(calculated from the level by the linearization functionality)

To ensure that the measuring device remains in proper condition for the operation

time:

• Use the measuring device only for measured materials against which the

process-wetted materials are adequately resistant.

• Observe the limit values in "Technical data".

Pulscon LTC57 PROFIBUS PA

Basic safety instructions

274505 2015-04

9

Incorrect use

The manufacturer is not liable for damage caused by improper or non-designated

use.

Verification for borderline cases:

• For special measured materials and cleaning agents, Pepperl+Fuchs is glad

to provide assistance in verifying the corrosion resistance of wetted materials,

but does not accept any warranty or liability.

Residual risk

The electronics housing and its built-in components such as display module,

main electronics module and I/O electronics module may heat to 80 °C (176 °F)

during operation through heat transfer from the process as well as power

dissipation within the electronics. During operation the sensor may assume a

temperature near the temperature of the measured material.

Danger of burns due to heated surfaces!

• For high process temperatures: Install protection against contact in order to

prevent burns.

2.3 Workplace safety

For work on and with the device:

• Wear the required personal protective equipment according to

federal/national regulations.

2.4 Operational safety

Risk of injury.

• Operate the device in proper technical condition and fail-safe condition only.

• The operator is responsible for interference-free operation of the device.

Conversions to the device

Unauthorized modifications to the device are not permitted and can lead to

unforeseeable dangers.

• If, despite this, modifications are required, consult with the manufacturer.

Repair

To ensure continued operational safety and reliability,

• Carry out repairs on the device only if they are expressly permitted.

• Observe federal/national regulations pertaining to repair of an electrical

device.

• Use original spare parts and accessories from the manufacturer only.

274505 2015-04

10

Pulscon LTC57 PROFIBUS PA

Basic safety instructions

Hazardous area

To eliminate a danger for persons or for the facility when the device is used in the

hazardous area (e. g. explosion protection, pressure vessel safety):

• Based on the nameplate, check whether the ordered device is permitted for

the intended use in the hazardous area.

• Observe the specifications in the separate supplementary documentation

that is an integral part of these Instructions.

2.5 Product safety

This measuring device is designed in accordance with good engineering practice

to meet state-of-the-art safety requirements, has been tested, and left the factory

in a condition in which they are safe to operate.

It meets general safety standards and legal requirements. It also complies with

the EC directives listed in the device-specific EC Declaration of Conformity.

Pepperl+Fuchs confirms this by affixing the CE mark to the device.

Pulscon LTC57 PROFIBUS PA

Product description

274505 2015-04

11

3 Product description

3.1 Design

3.1.1 Device

Figure 3.1 Design

1Electronics housing

2Process connection (here as an example: flange)

3Rope probe

4End-of-probe weight

5Rod probe

1

2

5

3

4

Pulscon LTC57 PROFIBUS PA

274505 2015-04

12

Pulscon LTC57 PROFIBUS PA

Product description

3.1.2 Electronics housing

Figure 3.2 Design of the electronics housing

1Electronics compartment cover

2Display module

3Main electronics module

4Cable glands (1 or 2, depending on instrument version)

5Nameplate

6I/O electronics module

7Terminals (pluggable spring terminals)

8Connection compartment cover

9Grounding terminal

Esc

–+E

123

4

5

6

9

7

8

Pulscon LTC57 PROFIBUS PA

Incoming acceptance and product identification

274505 2015-04

13

4 Incoming acceptance and product identification

4.1 Incoming acceptance

Is the order code on the

delivery note (1)

identical to the order

code on the product

sticker (2)?

Are the goods

undamaged?

Do the nameplate data

match the ordering

information on the

delivery note?

Is the DVD (operating

tool) present?

If required (see

nameplate): Are the

Safety Instructions (SI)

present?

Table 4.1

Note!

If one of the conditions does not comply, contact your Pepperl+Fuchs distributor.

DELIVERY NOTE

1 = 2

DELIVERY NOTE

Made in Germany

Pulscon LTC57 PROFIBUS PA

274505 2015-04

14

Pulscon LTC57 PROFIBUS PA

Incoming acceptance and product identification

4.2 Product identification

The following options are available for identification of the measuring device:

• Nameplate specifications

• Order code with breakdown of the device features on the delivery note

• Scan the 2-D matrix code (QR code) on the nameplate: all the information for

the measuring device is displayed.

Nameplate

Figure 4.1 Example of a nameplate

1Order code

2Serial number (Ser. no.)

3Extended order code (Ext. ord. cd.)

42-D matrix code (QR code)

Order code:

Ext. ord. cd.:

Ser. no.:

1

2

3

4

Note!

For detailed information about interpreting the nameplate specifications, refer to

the Operating Instructions for the device.

Only 33 digits of the extended order code can be indicated on the nameplate. If

the extended order code exceeds 33 digits, the rest will not be shown. However,

the complete extended order code can be viewed in the operating menu of the

device in the Extended order code 1 to 3 parameter.

Pulscon LTC57 PROFIBUS PA

Incoming acceptance and product identification

274505 2015-04

15

4.3 Device documentation

Detailed information about the device can be found in the Operating Instructions

and the other documentation via internet www.pepperl-fuchs.com.

The complete device documentation consists of:

• these Quick Start Guide

• the Operating Instructions

• the Technical Information

Note!

These Instructions are Quick Start Guides; they are not a substitute for

the Operating Instructions pertaining to the device.

Note!

Technical documentation can also be downloaded from the Pepperl+Fuchs web

site: www.pepperl-fuchs.com. However this technical documentation applies to a

particular instrument family and is not assigned to a specific device.

274502 2015-04

16

Pulscon LTC51 PROFIBUS PA

Storage, Transport

5Storage, Transport

5.1 Storage conditions

• Permitted storage temperature: -40 ... +80 °C (-40 ... +176 °F)

• Use the original packaging.

5.2 Transport product to the measuring point

Figure 5.1

Figure 5.2

Warning!

Risk of injury!

Housing or probe may be damaged or break away.

• Transport the measuring device to the measuring point in its original

packaging or at the process connection.

• Do not fasten lifting devices (hoisting slings, lifting eyes etc.) at the housing or

the probe but at the process connection. Take into account the mass center

of the device in order to avoid unintended tilting.

• Comply with the safety instructions, transport conditions for devices over

18 kg (39.6 lbs) (IEC 61010).

Pulscon LTC57 PROFIBUS PA

Mounting

274505 2015-04

17

6 Mounting

6.1 Mounting requirements

6.1.1 Suitable mounting position

Figure 6.1 Mounting requirements

Mounting distances

• Distance (A) between wall and rod or rope probe:

• for smooth metallic walls: > 50 mm (2 in)

• for plastic walls: > 300 mm (12 in) to metallic parts outside the vessel

• for concrete walls: > 500 mm (20 in), otherwise the available measuring

range may be reduced.

• Distance (B) between rod or rope probe and internal fittings in the vessel:

> 300 mm (12 in)

• Distance (C) from end of probe to bottom of the vessel:

• Rope probe: > 150 mm (6 in)

• Rod probe: > 10 mm (0.4 in)

132

A

C

4

B

Pulscon LTC57 PROFIBUS PA

274505 2015-04

18

Pulscon LTC57 PROFIBUS PA

Mounting

Additional conditions

• When mounting in the open, a weather protection cover (1) may be installed

to protect the device against extreme weather conditions.

• In metallic vessels: Preferably do not mount the probe in the center of the

vessel (2), as this would lead to increased interference echoes.

If a central mounting position can not be avoided, it is crucial to perform an

interference echo suppression (mapping) after the commissioning of the

device.

• Do not mount the probe in the filling curtain (3).

• Avoid buckling the rope probe during installation or operation (e. g. through

product movement against silo wall) by selecting a suitable mounting

location.

• Check the probe regularly for defects.

Note!

With suspended rope probes (probe end not fixed at the bottom) the distance

between the probe rope and internal fittings in the tank must not fall below

300 mm (12 in) during the entire process. A sporadic contact between the probe

weight and the cone of the vessel, however, does not influence the measurement

as long as the dielectric constant of the medium is at least DC = 1.8.

Note!

When mounting the electronics housing into a recess (e. g. in a concrete ceiling),

observe a minimum distance of 100 mm (4 in) between the cover of the terminal

compartment/electronics compartment and the wall. Otherwise the connection

compartment/electronics compartment is not accessible after installation.

Pulscon LTC57 PROFIBUS PA

Mounting

274505 2015-04

19

6.1.2 Notes on the process connection

Probes are mounted to the process connection with threaded connections or

flanges. If during this installation there is the danger that the probe end moves so

much that it touches the tank floor or cone at times, the probe must, if necessary,

be shortened and fixed down.

Threaded connection

Figure 6.2 Mounting with threaded connection; flush with the container ceiling

Seal

The thread as well as the type of seal comply to DIN 3852 part 1, screwed plug

form A.

They can be sealed with the following types of sealing rings:

• Thread G3/4: according to DIN 7603 with the dimensions 27 x 32 mm

• Thread G1-1/2: According to DIN 7603 with the dimensions 48 x 55 mm

Please use a sealing ring according to this standard in the form A, C or D and of a

material that is resistant to the application.

274505 2015-04

20

Pulscon LTC57 PROFIBUS PA

Mounting

Nozzle mounting

Figure 6.3

Length H of the rigid part of the rope probe

• Permissible nozzle diameter: 150 mm (6 in).

For larger diameters the near range measuring capability may be reduced.

For nozzles DN300: see next section.

• Permissible nozzle height

1

:150 mm (6 in).

For a larger height the near range measuring capability may be reduced.

Larger nozzle heights may be possible in special cases: see next section.

Probe H

Rope Ø4 mm (0.16 in) 120 mm (4.7 in)

Rope Ø6 mm (0.24 in) 135 mm (5.3 in)

Table 6.1

1

Larger nozzle heights on request.

≤150 (6)

H

mm (in)

ø ≤150 (6)

Note!

With thermally insulated vessels the nozzle should also be insulated in order to

prevent condensate formation.

Page is loading ...

Pepperl+Fuchs LTC57 Operating instructions

Pepperl+Fuchs LTC57 Operating instructions

Related papers

Other documents