Rotel C8 Owner's manual
- Category
- Supplementary music equipment
- Type
- Owner's manual
This manual is also suitable for
Rotel C8, an eight-channel power amplifier, provides versatile audio solutions for various applications. With its ability to bridge channels, it delivers higher power output for demanding speakers. The unit features independent volume, source, bass, treble, and balance controls for each zone, allowing for customized audio experiences in different rooms. It offers multiple input options, including analog, digital, and line-level connections, ensuring compatibility with various audio sources.
Rotel C8, an eight-channel power amplifier, provides versatile audio solutions for various applications. With its ability to bridge channels, it delivers higher power output for demanding speakers. The unit features independent volume, source, bass, treble, and balance controls for each zone, allowing for customized audio experiences in different rooms. It offers multiple input options, including analog, digital, and line-level connections, ensuring compatibility with various audio sources.
Owner’s Manual
Manuel de l’utilisateur
Bedienungsanleitung
Manual de Instrucciones
Gebruikershandleiding
Manuale di istruzioni
Instruktionsbok
Инструкция пользователя
C8
C8+
Eight Channel Power Ampliers
Amplicateurs de Puissance Huit Canaux
Achtkanal-Endstufe
Etapas de Potencia de Ocho Canales
Achtkanaals vermogensversterkers
Amplicatori nali a otto canali
8-kanals slutsteg
8-канальный усилитель мощности
ZONE 1 ZONE 2 ZONE 3 ZONE 4
ENTER
MENU BACK
FUNCTION
C8
2C8 / C8+ Eight Channel Power Ampliers
Notice
The RS232 connection should be handled by authorized persons only.
WARNING: There are no user serviceable parts inside. Refer all servicing
to qualified service personnel.
WARNING: To reduce the risk of fire or electric shock, do not expose
the unit to moisture or water. Do not expose the unit to dripping or
splashing. Do not place objects filled with liquids, such as vases, on
the unit. Do not allow foreign objects to get into the enclosure. If the
unit is exposed to moisture, or a foreign object gets into the enclosure,
immediately disconnect the power cord from the wall. Take the unit to a
qualified service person for inspection and necessary repairs.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat. Do
not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from
the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for
long periods of time.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power supply
cord or plug is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
The apparatus should be used in non tropical climate.
The ventilation should not be impeded by covering the ventilation openings
with items, such as newspapers, table-cloths, curtains, etc.
No naked flame sources, such as lighted candles, should be placed on
the apparatus.
Touching uninsulated terminals or wiring may result in an unpleasant
sensation.
Rotel products are designed to comply with international
directives on the Restriction of Hazardous Substances
(RoHS) in electrical and electronic equipment and the
disposal of Waste Electrical and Electronic Equipment
(WEEE). The crossed wheelie bin symbol indicates
compliance and that the products must be appropriately
recycled or processed in accordance with these directives.
Important Safety Instructions
You must allow a minimum 50 cm or 20 inches of unobstructed
clearance around the back of the unit.
> 50 cm
> 20 in
WARNING:
The rear panel power cord connector is the mains power
disconnect device. The device must be located in an open area that
allows access to the cord connector.
The unit must be connected to a power supply only of the type and
voltage specified on the side panel. (USA: 120 V/60Hz, EC: 230V/50Hz)
Connect the component to the power outlet only with the supplied power
supply cable or an exact equivalent. Do not modify the supplied cable.
Do not use extension cords.
The main plug is the disconnect of the unit. In order to completely
disconnect the unit from the supply mains, remove the main plug from
the unit and the AC power outlet. This is the only way to completely
remove mains power from the unit.
Use Class 2 wiring for speaker connections to ensure proper installation
and minimize the risk of electrical shock.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following to conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
3
English
ZONE 1 ZONE 2 ZONE 3 ZONE 4
ZONE 1 ZONE 2 ZONE 3 ZONE 4
RP-613B
BRIDGED ZONE 1&2 BRIDGED ZONE 3&4
ENTER
MENU BACK
FUNCTION
C8
1 2
8
9 = q
3 4
75
-0
Figure 1-1: Controls and Connections
Commandes et branchements
Bedienelemente und Anschlüsse
Controles y Conexiones
Bedieningselementen en aansluitingen
Controlli e connessioni
Kontroller och kontakter
Органы управления и разъемы
1: Power Button
Activate the unit or put it into standby mode.
2: ZONE 1 - 4
Congure the volume, source, bass treble and balance for Zone
1 to Zone 4 respectively.
3: Display
4: Function Buttons
Navigating and ENTER Buttons
MENU Button
BACK Button
4C8 / C8+ Eight Channel Power Ampliers
ZONE 1 ZONE 2 ZONE 3 ZONE 4
ZONE 1 ZONE 2 ZONE 3 ZONE 4
RP-601E
BRIDGED ZONE 1&2 BRIDGED ZONE 3&4
ENTER
MENU BACK
FUNCTION
C8+
1 2
68
9= q
3 4
7
5
-0
Figure 1-2: Controls and Connections
Commandes et branchements
Bedienelemente und Anschlüsse
Controles y Conexiones
Bedieningselementen en aansluitingen
Controlli e connessioni
Kontroller och kontakter
Органы управления и разъемы
ZONE 1 ZONE 2 ZONE 3 ZONE 4
ZONE 1 ZONE 2 ZONE 3 ZONE 4
RP-613B
BRIDGED ZONE 1&2 BRIDGED ZONE 3&4
ENTER
MENU BACK
FUNCTION
C8
1 2
8
9= q
3 4
7
5
-0
5: Bridged Slide Switches
Allow 2 amplier channels to be connected providing higher power for
larger or more demanding speakers.
6: Digital Input
Use for digital connection.
7: Line Output
Use for live level connection.
8: Analog Input
Use for analog connection.
9: Speaker Connectors
0: 12V Trigger Input and Output
-: Network Port
Use for software updates and integration with automation systems.
=: RS232 Port
Use for integration with automation systems.
q: AC Power Inlet
5
English
ZONE 1 ZONE 2 ZONE 3 ZONE 4
RP-601E
BRIDGED ZONE 1&2 BRIDGED ZONE 3&4
PUSH PUSH
ON
OFF
Rotel RSP-1576MKII
Rotel C8+
Move the BRIDGE slide
switches to the OFF position.
Figure 2: Connection Illustration
Schéma de raccordement
Anschlussdiagramm
Ilustración del Conexionado
Aansluiten Afbeelding
Collegamento
Anslutningar
Подсоединение -пример
6C8 / C8+ Eight Channel Power Ampliers
Figure 3: Bridged Connection Illustration
Schéma de raccordement pontée
Abbildung der gebrückten Verbindung
Ilustración del Conexionado en puente
Overbrugde Aansluiten Afbeelding
Collegamento a ponte
Överbryggad Anslutningar
Подсоединение мостового -пример
ZONE 1 ZONE 2 ZONE 3 ZONE 4
RP-601E
BRIDGED ZONE 1&2 BRIDGED ZONE 3&4
PUSH PUSH
ON
OFF
Rotel RSP-1576MKII
Rotel C8+
Move the BRIDGE slide
switches to the ON position.
7
English
Important Notes
When making connections be sure to:
4 Turn off all the components in the system before hooking up any components, including loudspeakers.
4 Turn off all components in the system before changing any of the connections to the system.
It is also recommended that you:
4 Turn the volume control of the amplier all the way down before the amplier is turned on or off.
Remarques importantes
Pendant les branchements, assurez-vous que :
4 Tous les maillons sont éteints avant leur branchement, quels qu’ils soient, y compris les enceintes acoustiques.
4 Éteignez tous les maillons avant de modier quoi que ce soit au niveau de leurs branchements, quels qu’ils soient.
Il est également recommandé de :
4 Toujours baissez le niveau sonore via le contrôle de volume, avant d’allumer ou d’éteindre l’amplicateur.
Wichtige Hinweise
Achten Sie beim Herstellen der Verbindungen auf Folgendes:
4 Schalten Sie alle Komponenten im System ab, bevor Sie Geräte (einschließlich Lautsprecher) anschließen.
4 Schalten Sie alle Komponenten im System ab, bevor Sie Anschlüsse im System verändern.
Ferner empfehlen wir, dass
4 Sie die Lautstärke herunterdrehen, bevor Sie die Endstufe ein- oder abschalten.
Notas Importantes
Cuando realice las conexiones, asegúrese de que:
4 Desactiva todos los componentes del equipo, cajas acústicas incluidas, antes de conectar cualquier nuevo componente en el mismo.
4 Desactiva todos los componentes del equipo antes de cambiar cualquier conexión del mismo.
También le recomendamos que:
4 Reduzca el nivel de volumen de su amplicador a cero antes de activarlo o desactivarlo.
Héél belangrijk
Bij het maken van de verbindingen:
4 Zorg dat niet alleen de C8/C8+ versterkers, maar de gehele installatie uitstaat, als nog niet alle verbindingen gemaakt zijn.
4 Zorg dat niet alleen de C8/C8+ versterkers, maar de gehele installatie ook uitstaat, als u verbindingen gaat wijzigen.
Wij raden u ook aan om
4 de volumeregelaar van de voorversterker geheel dicht te draaien (volkomen naar links) wanneer u uw eindversterker aan- of uitzet.
Note importanti
Quando effettuate i collegamenti assicuratevi di:
4 Spegnere tutti i componenti del sistema prima di collegare qualsiasi componente, inclusi i diffusori.
4 Spegnere tutti i componenti del sistema prima di modicare qualsiasi connessione nel sistema.
Vi raccomandiamo inoltre di:
4 Portare il volume a zero prima di accendere o spegnere l’amplicatore.
Viktigt
Tänk på följande när du gör anslutningar:
4 Stäng av alla apparater i anläggningen innan du ansluter nya komponenter eller högtalare.
4 Stäng av alla apparater i anläggningen innan du ändrar någon anslutning.
Vi rekommenderar också att du:
4 Vrider ner volymen på förstärkaren helt och hållet innan förstärkaren slås på eller av.
Важные замечания
Перед подсоединением:
4 Выключите все компоненты, включая колонки.
4 Выключите все компоненты в вашей системе, прежде чем что-то в ней менять.
Рекомендуется также:
4 Вывести громкость усилителя на минимум, перед тем как включать или выключать его.
8C8 / C8+ Eight Channel Power Ampliers
About Rotel
Our story began over 60 years ago. Over the decades, we have received
hundreds of awards for our products and satised hundreds of thousands
of people who take their entertainment seriously – like you!
Rotel was founded by a family whose passionate interest in music led them
to manufacture high-delity components of uncompromising quality. Through
the years, that passion has remained undiminished and the family goal of
providing exceptional value for audiophiles and music lovers, regardless
of their budget, is shared by all Rotel employees.
Rotel’s engineers work as a close team, listening to, and ne tuning, each
new product until it reaches their exacting musical standards. They are
free to choose components from around the world in order to make that
product the best they can. You are likely to nd capacitors from the United
Kingdom and Germany, semiconductors from Japan or the United States,
while toroidal power transformers are manufactured in Rotel’s own factory.
We all have concerns about our environment. And, as more and more
electronics are produced it is especially important for a manufacturer to do all
it can to engineer products that have a minimum impact on the environment.
At Rotel, we are proud to do our part. We have reduced the lead content
in our products by using special lead-free ROHS solder and components.
Our engineers continually strive to improve power supply efciency without
compromise to quality. When in standby mode Rotel products use minimal
power to meet global Standby Power Consumption requirements.
The Rotel factory is also doing their part to help the environment through
constant improvements to product assembly methods for a cleaner and
greener manufacturing processes.
All of us at Rotel thank you for buying this product. We are sure it will bring
you many years of enjoyment.
A Word About Watts
The C8 power output is quoted as 70 watts for each channel when all eight
channels are operating together at full power into 4 ohms. The C8+ power
output is quoted as 150 watts for each channel when all eight channels
are operating together at full power into 4 ohms.
Rotel has chosen to specify the power output in this way because, in Rotel’s
experience, it gives the truest value of the receiver or amplier’s power
capability.
When comparing specications for different products, you should be
aware that power output is often specied in other ways, so you may not
be comparing like with like. For example, the power output may be quoted
with only one channel operating, giving a higher maximum gure.
A loudspeaker’s impedance rating indicates the electrical resistance or
load it offers when connected to the amplier, usually 8 ohms or 4 ohms.
The lower the impedance, the more power the speaker will need. In effect,
a 4 ohm speaker will require twice as much power as an 8 ohm speaker.
However, Rotel ampliers are designed to work into any speaker impedance
between 8 and 4 ohms, and with all the channels working up to their full
power. Because the Rotel design is optimized for use with all channels
Contents
Important Safety Instructions ..........................................2
Figure 1-1: Controls and Connections 3
Figure 1-2: Controls and Connections 4
Figure 2: Connection Illustration 5
Figure 3: Bridged Connection Illustration 6
Important Notes 7
About Rotel .......................................................8
A Word About Watts ................................................8
Getting Started ....................................................9
A Few Precautions 9
Placement 9
Cable 9
AC Power and Control ...............................................9
AC Power Input q 9
Power Switch and Power Indicator 1 10
12V Trigger Input and Output 0 10
Protection Indicator 1 10
Signal Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Analog Inputs 8 10
Mono Switch 8 10
Line Output 7 10
Digital Inputs 6 10
Speaker Outputs ..................................................10
Speaker Selection 10
Speaker Wire Selection 10
Polarity and Phasing 11
Speaker Wire Connections 11
Plug connection 9 11
Brideged Speaker Outputs Connection 5 ................................11
Network Connection - .............................................11
RS232 Connector = ...............................................11
Cooling Fan .....................................................11
Front Panel Overview ..............................................11
ZONE 1-4 2 11
Display 3 12
Function Button 4 12
Settings Menu ....................................................12
Troubleshooting ...................................................13
Power Indicator Is Not Illuminated 13
Fuse Replacement 13
No Sound 13
Playable Audio Formats 13
Specications ....................................................14
9
English
operating together, Rotel is able to specify the true power output for all
channels.
This can be important for your enjoyment, too. When watching movies, it’s
nice to have the amplier able to reproduce full power into all the channels
at the same time, especially in the case of a volcano exploding!
Getting Started
Thank you for purchasing the Rotel Eight Channel Power Amplier. When
used in a high-quality music audio system, your Rotel product will provide
years of musical enjoyment.
This amplier is a full featured, high performance component. All aspects
of the design have been optimized to retain the full dynamic range and
subtle nuances of your music. The unit has a highly regulated power supply
incorporating a Rotel custom-designed toroidal power transformer. This low
impedance power supply has ample power reserves, which enables the
amplier to easily reproduce the most demanding audio signals. This type
of design is more expensive to manufacture, but it is better for the music.
The printed circuit boards (PCB) are designed with Symmetrical Circuit
Traces. This ensures that the precise timing of the music is maintained and
faithfully recreated. The circuitry uses metal lm resistors and polystyrene
or polypropylene capacitors in important signal paths. All aspects of this
design have been examined to ensure the most faithful music reproduction.
The main functions of the amplier are easy to install and use. If you have
experience with other stereo systems, you shouldn’t nd anything perplexing.
Simply plug in the associated components and enjoy.
A Few Precautions
WARNING: To avoid potential damage to your system, turn off ALL
the components in the system when connecting or disconnecting the
loudspeakers or any associated components. Do not turn the system
components back on until you are sure all the connections are correct
and secure. Pay particular attention to the speaker wires. There must
be no loose strands that could contact the other speaker wires, or the
chassis of the amplier.
Please read this manual carefully. In addition to basic installation and
operating instructions, it provides valuable information on various unit
system congurations as well as general information that will help you get
optimum performance from your system. Please contact your authorized
Rotel dealer for answers to any questions you might have. In addition, all
of us at Rotel welcome your questions and comments.
Save the shipping carton and all enclosed packing material for future use.
Shipping or moving the ampliers in anything other than the original packing
material may result in severe damage to your unit.
If included in the box please ll out and send in the owner’s registration
card or register on line. Also be sure to keep the original sales receipt. It is
your best record of the date of purchase, which you will need in the event
warranty service is ever required.
Placement
Like all audio components that handle low level signals, this amplier
can be affected by its environment. Avoid placing the unit on top of other
components. Also avoid routing audio signal cables near power cords. This
will minimize the chance it will pick up hum or interference.
The unit generate heat as part of their normal operation. The heat sinks and
ventilation openings in the amplier are designed to dissipate this heat. The
amplier requires 50 cm (20 inches) of clearance around the back side of
the chassis. Reasonable airow in the equipment rack is required to prevent
the amplier from overheating.
Remember the weight of the unit when you select an installation location. If
you are not using the included rack ears make sure that the shelf or cabinet
used can support the unit. We recommend installing the unit in furniture
designed to house audio components. Such furniture is designed to reduce
or suppress vibration which can adversely affect sound quality. Ask your
authorized Rotel dealer for advice about component furniture and proper
installation of audio components.
Cables
Be sure to keep the power cords, digital signal cables and analog audio
signal cables in your installation away from each other. This will minimize
the chance of the analog audio signal cables picking up noise or interference
from the power cords or digital cables. Using only high quality, shielded
cables will also help to prevent noise or interference from degrading the
sound quality of your system. If you have any questions see your authorized
Rotel dealer for advice about the best cable to use with your system.
AC Power and Control
AC Power Input q
Your unit is congured at the factory for the proper AC voltage in the country
where you purchased it (either 120 volts AC or 230 volts AC with a line
frequency of either 50 Hz or 60 Hz). The AC line conguration is noted
on a label on the side panel.
NOTE: Should you move your unit to another country, it may be possible
to recongure it for use on a different line voltage. Do not attempt to
perform this conversion yourself. Opening the enclosure of the unit
exposes you to dangerous voltages. Consult a qualied service person
or the Rotel factory service department for information.
NOTE: Some products are intended for sale in more than one country
and as such are supplied with more than one AC cord. Please only use
the one appropriate for your country/region.
Because of its high power rating, the unit can draw considerable current.
Therefore, it should be plugged directly into a wall outlet. The unit must
be plugged into a 3-pin polarized outlet. Do not use an extension cord.
A heavy duty multi-tap power outlet strip may be used if it (and the wall
outlet) is rated to handle the current demanded by the unit and all the other
components connected to it.
Be sure the POWER SWITCH 1 on the front panel of the unit is turned off
(in the “out” position). Then, connect the supplied power cord to the Power
Connector q on the rear of the unit and the AC power outlet.
If you are going to be away from home for an extended period of time
such as a month-long vacation, it is a sensible precaution to unplug your
unit (as well as other audio and video components) while you are away.
10 C8 / C8+ Eight Channel Power Ampliers
Power Switch and Power Indicator 1
The power switch is located on the front panel of your amplier. To turn the
unit on, push the switch in. The ring around the switch will light up and blink
three times, indicating that the amplier is turned on. To turn the amplier
off, push the button again and return it to the “out” position.
12V Trigger Input and Output 0
The jack labeled IN is for connecting the 3.5mm mono plug/cable carrying
a +12 volt trigger signal to turn the amplier on and off. This input accepts
any control signal (AC or DC) ranging from 3 volts to 30 volts.
The jack labeled OUT is for connecting another 3.5mm mono plug/cable
to provide a 12 volt trigger signal to other components. Any 12V Trigger
signal at the INPUT jack will be passed through to the OUT jack.
NOTE: The maximum current for the trigger out is 10mA.
Protection Indicator 1
The amplier has both thermal and over-current protection circuitry that
protects the amplier against damage in the event of extreme or faulty
operating conditions. The protection circuits are independent of the audio
signal and have no impact on sonic performance. Instead, the protection
circuits monitor the temperature of the output devices and shut down the
amplier if temperatures exceed safe limits.
Most likely, you will never see this protection circuitry in action. However,
should a faulty condition arise, the amplier will stop playing. The power
indicator 1 on the front panel will blink. The LEDs above the ZONE 1 - 4
also will blink to indicate which zone caused the protection.
If this happens, turn the amplier off. Let it cool down for several minutes,
and attempt to identify and correct the problem that caused the protection
circuitry to engage. When you turn the amplier back on, the protection
circuit will automatically reset and the power indicator 1 as well as the
LEDs above the ZONE 1 - 4 should light up, indicating that the amplier
is turned on normal.
In most cases, the protection circuitry activates because of a fault condition
such as shorted speaker wires, or inadequate ventilation leading to an
overheating condition. In very rare cases, highly reactive or extremely low
impedance speaker loads could cause the protection circuit to engage.
If the protection circuitry triggers repeatedly and you are unable to isolate
and correct the faulty condition, contact your authorized Rotel dealer for
assistance in troubleshooting.
Signal Connections
See Figure 1-2
NOTE: To prevent loud noises that neither you nor your speakers will
appreciate, make sure the system is turned off when you make any
signal connections.
The unit provides standard RCA type input connections as found on nearly
all audio equipment.
In addition to the four groups of stereo inputs labeled ANALOG INPUT A
to D, there is also a pair of LINE OUT connections for passing the signal
connected to the unit to another audio component.
Analog Inputs 8
There are two Analog inputs for each of the four pairs of unit channels.
These Analog inputs accept audio signals from preampliers or surround
sound processors. Select high quality audio interconnect cables for best
performance.
For each pair of amplier channels, connect the left channel output of your
preamp to the LEFT INPUT on the amplier. Connect the right channel of
your preamp to the RIGHT INPUT. Make sure that the input A slide switch
is in the STEREO position.
Mono Switch 8
For the channel INPUT A, when the input A slide switch is moved to the
MONO position, the left and right signals are combined and provided to
both speakers as a mono signal.
Line Output 7
This pair of Line level connections can be used to pass unprocessed input
signals to another audio component, for example to “daisy-chain” to another
amplier to drive additional speakers. The input signals connected to the
INPUT A connectors is available on the Line Output connectors. This is
typically used when the unit is part of a multi-room system.
NOTE: It is recommended to Daisy Chain a maximum of 8 units.
NOTE: The MONO switch does not affect the Line Output.
Digital Inputs 6
For C8+ Only
There are two sets of digital inputs labeled DIGITAL INPUT A to D. Connect
the DIGITAL outputs of your source component into these sockets. The digital
signals will be decoded and played by the amplier. The unit is capable of
decoding PCM signals up to 24 bit, 192kHz.
Speaker Outputs
See gure 2
The unit has four pairs of speaker connectors, one for each amplier channel.
The eight speaker connectors may be used in many different congurations. The
Hook-up Illustration, Figure 2, shows just one example, with the connections
for a typical six-speaker system. Here, the remaining two channels are still
available to power up to two more speakers as required.
Speaker Selection
We recommend using loudspeakers with a nominal impedance of 4 ohms or
higher with the unit. You should not drive more than one pair of speakers for
each output channel. Driving more than one set of speakers from an output
may damage the unit. Speaker impedance ratings are less than precise. In
practice, very few loudspeakers will present any problems for the unit. See
your authorized Rotel dealer if you have any questions.
Speaker Wire Selection
Use insulated two-conductor stranded wire to connect the unit to the speakers.
The size and quality of the wire can have an audible effect on the performance
of the system. Standard speaker wire will work, but can result in lower
output or diminished bass response, particularly over longer distances. In
general, heavier wire will improve the sound. For best performance, you
may want to consider special high-quality speaker cables. Your authorized
Rotel dealer can help in the selection of cables for your system.
11
English
Polarity and Phasing
The polarity – the positive/negative orientation of the connections – for every
speaker and amplier connection must be consistent so all the speakers will
be in phase. If the polarity of one connection is reversed, bass output will
be very weak and stereo imaging degraded. All wire is marked so you can
identify the two conductors. There may be ribs or a stripe on the insulation
of one conductor. The wire may have clear insulation with different color
conductors (copper and silver). There may be polarity indications printed
on the insulation. Identify the positive and negative conductors and be
consistent with every speaker and amplier connection.
Speaker Wire Connections
Turn off all the components in the system before connecting the speakers.
Route the wire from the unit to the speakers. Give yourself enough slack so
you can move the components to allow access to the speaker connectors.
For each group of channels, connect the left speaker to the pair of speaker
connectors labeled LEFT. Connect the right speaker to the speaker connectors
labeled RIGHT. Make sure that the positive terminal of the speaker is connected
to the + terminal on the unit. Make sure that the negative terminal of the
speaker is connected to the - terminal of the unit.
NOTE: Be sure there are no loose wire strands that could touch adjacent
wires or connectors.
Plug connection 9
Connect the speaker wires as shown in the illustration. Insert the wire into
the opening and turn the screw to clamp the wire in place.
Be sure to keep the polarity of the connections correct. Speaker connectors
can be secured to the unit using the secure-locking screws on each side of
the connector. This will help prevent the connectors from falling out from
the socket.
R+
R--
L--
L+
Bridged Speaker Outputs Connection 5
See gure 3
Bridging allows 2 amplier channels to be connected providing higher
power for larger or more demanding speakers. To enable the bridging
function slide the BRIDGE ZONE 1&2 or BRIDGE ZONE 3&4 slide switch
5 to the ON position.
When bridged use the Left and Right input for Input A (Zone 1 and 2 bridged)
or the Input C (Zone 3 and 4 bridged).
Speaker output connections must follow the diagram found in Figure 3 to
ensure output power is properly wired from the unit to the speakers.
NOTE: Failure to following the bridging speaker wiring diagram will
result in inefcient output and will not properly bridge the amplier
channels together.
Network Connection -
The amplier can be attached to a network using the rear panel NETWORK
socket -. The NETWORK congurations allow both STATIC and DHCP IP
addressing. See the Network section of this manual under Setting Menu for
IP address conguration information.
The NETWORK connection allows software updates to be downloaded from
the Internet. The NETWORK connection also allows IP control for integration
with automation systems.
For additional information on the IP control please contact your authorized
Rotel dealer.
RS232 Connector =
The unit can be controlled via RS232 for integration with automation systems.
The RS232 input accepts a standard STRAIGHT DB-9 Male-to-Female cable.
For additional information on the connections, software, and operating codes
for RS232 control of the amplier, contact your authorized Rotel dealer.
Cooling Fans
The amplier includes 2 cooling fans to help exhaust the heat generated
by the power supply and amplier modules. These fans will operate when
internal thermostat sensors detect cooling is required. The fan speed with
increase as needed when the unit temperature increases as detected by
the internal sensors.
NOTE: If the cooling fans and cooling tunnels require cleaning please
contact your authorized Rotel dealer for more information.
Front Panel Overview
The following is a brief overview of the controls and features on the front
panel of the unit.
ZONE 1-4 2
The unit can control the volume, source, bass treble and balance for Zone 1
to Zone 4 respectively. Press the ZONE 1 - 4 buttons to toggle between the
menus and use the //‹/› arrow buttons to change the value. Press and
hold any ZONE 1 - 4 buttons can mute the source from the corresponding
ZONE 1 - 4.
VOLUME: 0 ~ 96. Default: 45.
12 C8 / C8+ Eight Channel Power Ampliers
SOURCE: INPUT A, INPUT B, INPUT C, INPUT D.
BASS: -10 ~ +10. Default: 0.
TREBLE: -10 ~ +10. Default: 0.
BALANCE: L10 ~ R10. Default: 0.
Display 3
The front panel display shows the source selected, volume level and tone
settings. The display provides access to the setup and conguration menu
options of the unit and can be dimmed using the setup menu.
Function Button 4
Navigating and ENTER Buttons: Use the navigation / / /› buttons and the
ENTER button on the front panel to access the various menus and operate
the unit settings.
MENU Button: The MENU button activates the setup screen on the front
panel. Push the MENU button again to exit setup menu and go back to
normal display.
BACK Button: Pressing briey returns to the previous selection screen.
Settings Menu
You can access the SETUP menu from the front panel by pressing the MENU
4 button. You can change the value of the selected option by pressing
the ‹/› 4 arrow buttons on the front panel. Step through the sub-menus
by pressing the ENTER 4 button on the front panel.
• INPUT SOURCE: Congure the source to the INPUT A, B, C and D.
Valid settings include: AUTO (Default), ANALOG, DIGITAL.
NOTE: When both analog and digital source are connected to the unit,
the unit will select the digital source as a priority if there is a clocking
signal or audio if set to AUTO.
• ZONE SOURCE: Congure the source input for Zone 1 - 4 as xed or
Matrix-ed from all available source inputs.
Valid settings include: MATRIX (Default), INPUT A, INPUT B, INPUT C, INPUT D.
NOTE: When set to MATRIX the front panel ZONE 1 - 4 buttons 2
allow section of the source input A - D.
• INPUT NAME: The name of the sources A - D can be customized. For
example INPUT A can be named “MUSIC” for easier reference. Press
the ENTER button to enter the source name edit sub menu as below. The
maximum source name is limited to 10 characters.
Name:
-0123456789ABCD
EFGHIJKLMNOPQRST
UVWXYZ DEL DONE
• ZONE NAME: The name of the Zones 1-4 can be customized. For example
ZONE 1 can be named “AUDIO” for easier reference. Press the ENTER
button to enter the zone name edit sub menu as below. The maximum
zone name is limited to 6 characters.
Name:
-0123456789ABCD
EFGHIJKLMNOPQRST
UVWXYZ DEL DONE
• MAX VOLUME: This sets the maximum volume level for ZONE 1 - 4. “75”
is the factory default. Max volume limits the volume level using the front
panel Zone 1 - 4 controls.
Valid settings include: 0 ~ 96. Default: 75.
• LCD DIMMER: Dims the front LCD display.
Valid settings include: HIGH (Default), MEDIUM HIGH, MEDIUM, MEDIUM
LOW and LOW.
• LED DIMMER: Dims the Power LED on the front panel.
Valid settings include: HIGH (Default), MEDIUM and LOW.
• DISPLAY OPTION: Congures the front panel to always be on or turn off
after a timeout period. The front panel will always activate during power
on and when the front panel controls are used until the timeout period
expires. Use the TIMEOUT function if you do not want the front panel
displayed during normal operation.
Valid settings include: ON (Default), 5 SEC TIMEOUT, 10 SEC TIMEOUT.
• AUTO POWER OFF: The unit can be congured to automatically power
off if there is no active audio playing in a zone and the unit is unused
for a specied period. If the audio signal on all active Zones stops and
no changes are made to the unit within the specied period, the unit
will automatically go to STANDBY mode. The auto power off timer will
be restarted if audio is detected or if changes are made to the volume,
source or playback. The default is set to 20 MINS.
Valid settings include: 20 MINS (Default), DISABLE, 1 HOUR, 2 HOURS,
5 HOURS, 12 HOURS.
NOTE: When the 12V Trigger is connected the AUTO POWER OFF
function is disabled and the Trigger given priority to control STANDBY
power.
• AC POWER OPTION: If set to ON the unit will be powered on when AC
Power is connected and the front panel power button is depressed to the
on position. If set to STANDBY the unit will enter Standby mode when
AC Power is connected and the front panel power button is depressed.
This function is useful to identify the operation of the unit in the event of a
power failure and restore. The unit will either resume operation in the ON
state or will enter STANDBY after a power failure/restore.
Valid settings include: ON (Default), STANDBY.
• PA OVERRIDE: Enable INPUT A as PA Override signal input. When an
audio signal is detected on Input Source A the audio will immediately
13
English
be broadcast to all Zones 1- 4. The unit will resume the previous Source
Input after approximately 10 seconds of no audio on the INPUT A source.
Valid settings include: DISABLED (Default), ENABLED.
• PA OVERRIDE VOL: This sets the volume level of ZONE 1 - 4 when the PA
OVERRIDE function is activated. “45” is the factory default.
Valid settings include: 0 ~ 96. Default: 45.
• NETWORK WAKEUP: When set to Enabled the unit will maintain the Ethernet
IP connection even in Standby Mode allowing the unit to be powered on
via IP. If Disabled the unit will not power on from the IP connection and
must use either the front panel or RS232 to power on the unit.
Valid settings Include: DISABLED (Default), ENABLED.
NOTE: When Network Wakeup is enabled the unit will consume
additional power.
• NETWORK SETUP: In most systems, set the IP ADDRESS MODE to DHCP.
This setting will allow your router to assign an IP address to the unit
automatically. If your network uses xed IP addresses, set the IP ADDRESS
MODE to STATIC.
Valid settings Include: DHCP (Default), STATIC.
If STATIC mode is selected you must congure all settings for the network
including IP Address, Subnet Mask, Gateway and DNS Server. Press the
ENTER button to activate the rst digit in the line you want to change, then
use the ‹/› buttons to adjust the values and press the ENTER button to cycle
to the next digit. When the proper IP information is congured press the
ENTER button to move the cursor back to the previous menu and accept
the settings. After entering the STATIC IP address information the network
will be tested and connection status reported.
NOTE: For more information regarding network connection please
contact your authorized Rotel dealer.
NOTE: A network connection is not required for the unit to operate.
• NETWORK INFO: Shows the network information. Press the ENTER button
to view Network Connetion Status, IP Address, Subnet Mask, Gateway
and MAC Address.
• SOFTWARE VERSION: This shows the current software version loaded
into the unit.
• SOFTWARE UPDATED: The software can be updated if the unit is properly
connected to the Internet.
• Press the ENTER button on the front panel to check if a new software
version is available.
• If a new software version is available, use ‹/› arrow buttons to select
“UPDATE“ option and press the ENTER button to begin the software
update process.
• The new software will be downloaded from the Internet. The amplier
will power cycle when the software update is complete.
NOTE: Do NOT power off the unit during the software update process.
NOTE: It is recommended to Reset Factory Defaults after the software
update is complete.
• FACTORY DEFAULT: This sets the unit back to the original state as when it
left the factory. Press the ENTER button on the front panel to enter factory
reset menu. Use the / arrow buttons to select YES and press the ENTER
button again to begin reset, or select NO to cancel.
NOTE: All previously congured options will be erased and reset to
the factory default settings.
• EXIT: Exits this SETUP menu.
Troubleshooting
Most difculties in audio systems are the result of incorrect connections, or
improper control settings. If you encounter problems, isolate the area of the
difculty, check the control settings, determine the cause of the fault and
make the necessary changes. If you are unable to get sound from the unit,
refer to the suggestions for the following conditions:
Power Indicator Is Not Illuminated
The Power Indicator and the basic items in the Display window should be
illuminated whenever the unit is plugged into the wall power outlet and the
Power button is pushed in. If it does not illuminate, test the power outlet with
another electrical device, such as a lamp. Be sure the power outlet being
used is not controlled by a switch that has been turned off. If using 12V
trigger power-on, make sure that a trigger signal is present at rear panel
12V TRIGGER IN connector.
Fuse Replacement
If another electrical device works when plugged into the power outlet, but
the Power Indicator still will not illuminate when the unit is plugged into
the wall outlet, it indicates that the internal power fuse may have blown.
If you believe this has happened, contact your authorized Rotel dealer to
get the fuse replaced.
No Sound
Check the signal source to see if it is functioning properly. Make sure the
cables from the signal source to the amplier inputs are connected properly.
Be sure the Input Source is set to the proper input. Check the wiring between
the amplier and the speakers.
Playable Audio Formats
Optical
Format Notes
SPDIF LPCM 44.1k, 48k, 88.2k, 96k, 176.4k, 192k
16 bit, 24 bit
14 C8 / C8+ Eight Channel Power Ampliers
C8+C8+
Max Power outputMax Power output 150 watts / channel
(8 channels driven, 4 ohms)
Continuous Power OutputContinuous Power Output 100 watts / channel
(8 channels driven, 8 ohms)
Total Harmonic Distortion Total Harmonic Distortion < 0.1%
Intermodulation Distortion Intermodulation Distortion < 0.1%
(60 Hz : 7k Hz, 4:1)
Frequency Response Frequency Response
Line level Input 10 Hz - 100k Hz, +/- 0.5 dB
Tone ControlTone Control
Bass ±10dB at 100Hz
Treble ±10dB at 10kHz
Damping FactorDamping Factor (20 Hz – 20k Hz, 8 ohms) 80
Input Sensitivity / Impedance Input Sensitivity / Impedance
Line level Input (RCA) 0.43 V / 31k ohms
Input OverloadInput Overload
Line level Input (RCA) 2.8 V
Signal to Noise Ratio Signal to Noise Ratio (A weighting)
Line level Input (RCA) 100 dB
Crosstalk / Separation Crosstalk / Separation > 50 dB
DigitalDigital
Frequency Response Frequency Response 10 Hz - 20k Hz, +/- 0.5 dB
Signal to Noise Ratio Signal to Noise Ratio (A weighting) 102 dB
Input Sensitivity / Impedance Input Sensitivity / Impedance - 13.5 dBFS / 75 ohms
Digital InputsDigital Inputs SPDIF LPCM (up to 192kHz 24bit)
GeneralGeneral
Power Requirements:Power Requirements:
USA: 120 Volts, 60 Hz
EC: 230 Volts, 50 Hz
Power Consumption Power Consumption 980 watts
Standby Power ConsumptionStandby Power Consumption
Normal < 0.5 watts
Network Wakeup < 2 watts
BTU BTU (4 ohms, 1/8th power) 2744 BTU/h
Dimensions Dimensions (W x H x D) 430 x 97 x 414 mm
(17 x 3 7/8 x 16 2/7 ins)
Front Panel HeightFront Panel Height 2U (88.1 mm, 3 1/2 ins)
Weight Weight (net) 18.35 kg, 40.45 lbs.
Specications
C8C8
Max Power outputMax Power output 70 watts / channel
(8 channels driven, 4 ohms)
Continuous Power OutputContinuous Power Output 50 watts / channel
(8 channels driven, 8 ohms)
Total Harmonic Distortion Total Harmonic Distortion < 0.1%
Intermodulation Distortion Intermodulation Distortion < 0.1%
(60 Hz : 7k Hz, 4:1)
Frequency Response Frequency Response
Line level Input 10 Hz - 100k Hz, +/- 0.5 dB
Tone ControlTone Control
Bass ±10dB at 100Hz
Treble ±10dB at 10kHz
Damping FactorDamping Factor (20 Hz – 20k Hz, 8 ohms) 80
Input Sensitivity / Impedance Input Sensitivity / Impedance
Line level Input (RCA) 0.3 V / 31k ohms
Input OverloadInput Overload
Line level Input (RCA) 2.8 V
Signal to Noise Ratio Signal to Noise Ratio (A weighting)
Line level Input (RCA) 100 dB
Crosstalk / Separation Crosstalk / Separation > 50 dB
GeneralGeneral
Power Requirements:Power Requirements:
USA: 120 Volts, 60 Hz
EC: 230 Volts, 50 Hz
Power Consumption Power Consumption 570 watts
Standby Power ConsumptionStandby Power Consumption
Normal < 0.5 watts
Network Wakeup < 2 watts
BTU BTU (4 ohms, 1/8th power) 1537 BTU/h
Dimensions Dimensions (W x H x D) 430 x 97 x 414 mm
(17 x 3 7/8 x 16 2/7 ins)
Front Panel HeightFront Panel Height 2U (88.1 mm, 3 1/2 ins)
Weight Weight (net) 16.7 kg, 36.81 lbs.
All specifications are accurate at the time of printing.
Rotel reserves the right to make improvements without notice.
Rotel and the Rotel Hi-Fi logo are registered trademarks of The Rotel Co., Ltd, Tokyo,
Japan.
C8 / C8+ Owner’s Manual Ver A 061622 English
The Rotel Co. Ltd.
Tachikawa Bldg. 1F.,
2-11-4, Nakane, Meguro-ku,
Tokyo, 152-0031
Japan
Rotel USA
Sumiko
11763 95th Avenue North
Maple Grove, MN 55369
USA
Phone: (510) 843-4500 (option 2)
E-mail: [email protected]
Rotel Canada
Kevro International
902 McKay Rd. Suite 4
Pickering, ON L1W 3X8
Canada
Tel: +1 905-428-2800
Rotel Europe
Dale Road
Worthing, West Sussex BN11 2BH
England
Phone: + 44 (0)1903 221 710
Fax: +44 (0)1903 221 525
www.rotel.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
Rotel C8 Owner's manual
- Category
- Supplementary music equipment
- Type
- Owner's manual
- This manual is also suitable for
Rotel C8, an eight-channel power amplifier, provides versatile audio solutions for various applications. With its ability to bridge channels, it delivers higher power output for demanding speakers. The unit features independent volume, source, bass, treble, and balance controls for each zone, allowing for customized audio experiences in different rooms. It offers multiple input options, including analog, digital, and line-level connections, ensuring compatibility with various audio sources.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI