Water Well V53C User manual

Brand: Water Well

Model: V53C

Type: User manual

USERS MANUAL

MODEL: V53C

Freestanding Cold and Ambient Water Dispenser

PLEASE READ USER MANUAL CAREFULLY

BEFORE USE, STORE IN A SAFE PLACE

The Water Well (Pty) Ltd

Address: P.O. Box 1854, Pinetown, 3600

Sharecall No.: 0860 099355

e-mail: [email protected] website: www.waterwell.co.za

Warranty Term: 12 Months

NOTE: This product's warranty is applicable only if the product has a valid

proof of purchase document

Table of Contents

Important Safety Instructions 1/2

Characteristics 2

Installation of Water Dispenser 3

Installation of Filter Bottle 3/4

Installation of Standard Bottle 4

Specifications 5

Circuit Diagram 5

Parts Diagram 6

Trouble Shooting 7

Important Safety Instructions

When using electrical appliances, basic safety precautions should be

followed to prevent the risk of fire, electric shock, and injury to persons

or property. Read all instructions before using any appliance.

- DO NOT operate this or any other appliance that has a damaged

cord. Connect to properly polarised outlets only. No other appliance

should be plugged into the same outlet. Ensure that the plug is fully

inserted into the receptacle

- DO NOT run cord over carpeting or other heat insulators. DO NOT

cover the cord. Keep cord away from high traffic areas, and do not

submerge in water. DO NOT pull on the power cable

- We DO NOT recommend the use of an extension cord, as it may

overheat and become a fire hazard.

- Ensure the water dispenser is positioned in such away that the power

plug is always accessable.

- Keep the water dispenser away from direct heat and out of direct

sunshine.

- Ambient surrounding temperatures should be within 10˚C - 32˚C for

optimum working conditions

- When the unit is plugged in and the power is turned on, please ensure

that there is always water coming out of both water taps to avoid the

reservoirs running dry and damaging the unit.

- Clean you water dispenser regularly, approx. every 1-3 months.

- DO NOT clean the water dispenser with water if the unit is still plugged

into the wall socket, instead wipe clean with a damp cloth.

- DO NOT clean your water dispenser with flammable fluids. The fumes

can create a fire hazard or explosion.

- Exercise caution and use reasonable supervision when appliance is

used near children

2 3

- Do not tilt the water dispenser beyond 45˚ always keep upright

- Ensure the water dispenser is on a flat surface and placed at least

15cm from the wall.

- WARNING - Keep the water dispenser well ventilated if placed in an

enclosed area

- Unplug the water dispenser from the wall socket and drain all the

water from the water dispenser if the water dispenser is not in use for

a long time.

- Clean your water dispenser before use, if it has not been used for a

long period, discard the water from the hot & cold water taps, before

drinking.

- WARNING - Do not damage the thermostat

CAUTION: Plastic bags can be dangerous. To avoid danger of

suffocation, keep this bag away from babies and

children.

Characteristics

1. The Water Well cold water dispensers are energy efficient and emit

very little noise.

2. All the components of the water dispenser are made of high grade

materials and the design is firm and durable

3. The unit keeps the water within a certain temperature range. Cold

water will fluctuate between 6˚C-10˚C, this is your optimum

temperature range within an ambient surrounding temperature range

of 10 ˚C - 32 ˚C

4. The water dispenser uses a compressor system to cool the water,

using 5V when cooling the water.

5. The Water dispener can be used with either a Standard Water bottle

or a filtration bottle.

Installation of the Water Dispenser

1. Remove the water dispenser from its packaging

2. Place in an upright position away from direct heat or sunlight

3. Once you have inserted your water bottle (see sections 4 & 5) allow

the water to filter into the water dispenser.

4. Disguard the first few litres of water from both water taps to eliminate

any dust and dirt which may be in the unit

5. Once water has filled the reservoir tanks and is flowing out of both

water taps in the water dispenser, plug the water dispenser into a wall

socket and turn on the power switch on the back of the water

dispenser

6. Allow the water dispenser to stand for awhile to reach the optimum

water temperature.

Installation of a Filter Bottle

Bottle Support

1. Remove the Bottle Support from the water

dispenser by twisting the Bottle Support to

the left and lifting out of the water dispenser.

See Images 1 -3

Image 1

Image 2 Image 3

4 5

Image 1

3. Fill the filter bottle with 2lt of water and allow to filter into the water

dispenser.

4. Drain and discard the water from the water dispenser using the taps

and repeat point 3 twice more. (until water is clear in the bottom

compartment of the filter bottle.

5. Follow instructions 5 & 6 of water dispenser installation instructions.

Installation of Standard Water Bottle

1. Fill your standard water bottle with water and secure the bottle cap

onto the bottle neck.

2. Invert the bottle and pierce the bottle neck onto the spike in the

middle of the bottle support, ensure the standard bottle is sitting level

on the water dispenser. See Images 1 - 3 above

3. Follow instructions 5 & 6 of water dispenser installation instructions.

Image 2 Image 3

2. Insert the Filter Bottle, with the Bottle Valve attached into the open area

(Reservoir Tank) on top of

the water dispenser,

ensure that the Filter Bottle

sits level on the top of the

water dispenser.

See Images 4 - 5

Image 4 Image 5

Model No.: V53C

Rated voltage Frequency: 220 - 240V / 50Hz

Rated Cooling Power: 85W

Cold water capacity: 2.0l/h

Refrigerant: R134a

Optimum Environmental Ambient 10˚C - 32 ˚C

Temperature

Technical Data

Yellow

SW1

PTC

Green

Compressor Thermostat

Circuit Diagram

6 7

Troubleshooting

Note: Ensure the water dispenser is unplugged before attempting any

repair below

Problem Possible Reasons Possible Solutions

Indicator

Light

not working

1. Power supply isn’t

connected

2. The appropriate switch

may not be turned on

1. Make sure the plug is

connected to the socket and

the socket switch is on

2. Ensure the appropriate

switch is in the on position

Unit is

leaking

1. Water bottle is broken

2. Water Bottle Valve

may be broken

3. Silicone pipes may be

damaged

4. Water tap may be

damaged

1. Replace the water bottle

2. Replave Water Bottle Valve

3. Replace the silicone piping

4. Replace tap

Not Cooling

1. Fuse is burnt out

2. Cooling switch may be

damaged

3. Cooling line connection

is loose

1. Replace fuse

2. Replace Switch, check

connections

3. Repair connections

Parts Diagram

1. Bottle Support

2. Ambient Water Indicator Light

3. Cold Water Indicator Light

4. Ambient Water Tap

5. Cold Water Tap

6. Drip Tray

7. Power Cable

8. Powerr Switch

9. Refrigerating Controller

10. Radiator

11. Quick Drain

12. Earth Wire

Water Well V53C User manual

Brand: Water Well

Model: V53C

Type: User manual

Download PDF

report

Water Well V53C User manual

Water Well V53C User manual

Other documents