2. Computers & electronics
  3. Audio & home theatre
  4. Speaker mounts
  5. RBH Sound
  6. RSS Speaker Stands
RSS Speaker Stands

RBH Sound RSS Speaker Stands Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the RBH Sound RSS Speaker Stands Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What surfaces are suitable for the stands?
    How do I attach the speaker to the stand without the top plate?
    How long does it take for the mounting tape to fully cure?
    How do I adjust the height of the stands?
    How do I connect the speaker wire to the audio system?
Adjustable Height Speaker Stands
Assembly Instructions
Please unpack carefully and assemble on carpeted surface to avoid scratching.
This package should contain the following:
Part Number: Description: Quantity:
PS Post Sleeve* 2
LS Lock Screw 2
BL Bolt (long) 2
BS Bolt (short) 2
AK Allen Key 1
MT Mounting Tape 2
TP Top Plate 2
TB Top Bracket 2
SW Spike Wrench 1
RB Rubber Bumper 8
CS Carpet Spike 8
Included but not pictured here:
Part Number: Description: Quantity:
SB Stand Base 2
SP Stand Post 2
MS Mounting Screw 8
SS Speaker Bolt/Screw 2
FS Flat-head Screw 2
* Already installed in Stand Post(SP)
PS* LS BL BS
AK MT TP
TB SW RB CS
Step 1) If the stands are going to be used on a carpeted surface, install the carpet spikes(CS) fully into the pre-
drilled holes in the underside of the base, with the aid of the supplied spike installation wrench. If the
stands are going to be used on wood, tile or other hard surface, use the rubber isolation bumpers(RB) in
place of the spikes. (See Diagram 1)
Diagram 1
Continued on reverse…
Items not to scale
Step 2) Install the locking screw(LS) into the threaded hole in the top-side of the post(SP) (See Diagram 3) and
tighten to secure the telescoping portion of the post(SP).
Step 3) Attach the larger, bottom portion of the post(SP) to the base(SB) with a long
bolt(LB) and tighten it with the supplied allen key(AK). (See Diagram 2)
NOTE: Please make sure the wire management hole faces to the rear of the
base(SB). The rear of the stand is where the post is closest to the edge.
Step 4) Attach the speakers to the top plate(TP) or top bracket(TB). (See Diagram 3)
If using the top plate(TP), secure the top plate(TP) to the post(SP) with the
included at screw(FS).
NOTE: If using the top plate(TP), please secure the speaker with the included
2-sided mounting tape(MT) or the mounting screws(MS).
NOTE: If the mounting tape(MT) is used, ‘full adhesion’ takes up to 48 hours to fully cure – DO NOT
apply pressure to the speakers within this time.
If using the top bracket(TB), secure the speaker with the included speaker bolt/screw(BS). With the rear
of the speaker against the the top bracket(TB), place speaker bolt/screw(BS) through the top bracket(TB)
and thread into the provision on the rear of the enclosure. (See Diagram 4)
Step 5) Adjust the stands to the required height by loosening the locking screw(LS), adjusting the height of the
speaker and then re-tightening the locking screw(LS) fully. Feed the speaker wire through the post(SP)
(See Diagrams 4&5) and connect to the audio system.
RBH Sound, Inc.
976 N. Marshall • Bldg. 2, #4 • Layton, Utah • USA • 84041
Toll-free: (800) 543-2205 • Fax: (801) 543-3300 • www.rbhsound.com
Diagram 2
Diagram 3 Diagram 4 Diagram 5
/