Astria Fireplaces Merit Louverless Instruction Sheet

Brand: Astria Fireplaces

Model: Merit Louverless

Type: Instruction Sheet

GENERAL INFORMATION

HORIZONTAL TERMINATION

SHROUD KIT

The horizontal Termination Shroud Kit may be used as a decorative cover

for the square termination and to minimize exposure to the hot surface

of the termination.

This kit contains one termination shroud kit and these instructions.

If you encounter any problems, need clariﬁcation of these instructions

or are not qualiﬁed to properly install this kit, contact you local distribu-

tor or dealer.

Read this instruction sheet in its entirety before beginning the installation.

ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND

OPERATION MANUALS PROVIDED WITH THE APPLIANCE APPLY TO

THESE INSTRUCTIONS.

HEARTH PRODUCTS

KITS AND ACCESSORIES

INSTALLATION INSTRUCTIONS FOR THE HORIZONTAL TERMINATION SHROUD KIT FOR USE

WITH SQUARE TERMINATIONS WHICH MAY BE USED WITH DIRECT VENT GAS FIREPLACES

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

P/N 750246M

REV. D 10/2015

PFS

USC

WARNING

THIS KIT MUST BE INSTALLED BY A QUALIFIED SERVICE

TECHNICIAN OR OTHER QUALIFIED AGENCY ACCORDING

TO THE MANUFACTURER’S INSTRUCTIONS, ALL CODES

AND REQUIREMENTS OF THE AUTHORITY HAVING JURIS-

DICTION IN THE USA OR CANADA. THE QUALIFIED AGENCY

PERFORMING THIS WORK ASSUMES RESPONSIBILITY FOR

THIS INSTALLATION.

WARNING

THE TERMINATION SHROUD PROVIDES A BARRIER TO PRE-

VENT DIRECT CONTACT WITH THE HOT TERMINATION EXCEPT

AT THE TOP PORTION OF THE TERMINATION SHROUD. THIS

AREA IS EXTREMELY HOT DUE TO THE DISCHARGING FLUE

GASES.

KIT CONTENTS (See Figure 1)

1 ea. Shroud Top

1 ea. Shroud Body

1 ea. Bottom Screen

8 Ea. Screws,10 X 1/2” Black Phillips

1 ea. Instruction Sheet

Figure 1

Termination Shroud Kit

Cat. No. Model Description

H5820 SV4.5-HTSK Termination Shroud Kit

P/N 750246M REV. D 10/2015

Figure 2

Termination

Securing Screws

(Five) For Shroud

Body To Shroud Top.

Install From The

Bottom Up.

Screw Flanges

(Five Places)

Bottom Screen

Termination

Shroud - Top

Termination

Shroud - Body

Back Off These Two Screws

(Both Sides) And Slide

Shroud Body Into Place.

Securing Screws

(Three) For Bottom

Screen To Shroud Body.

Install From The Bottom Up.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

IHP reserves the right to make changes at any time, without notice, in design, materials,

speciﬁcations, prices and also to discontinue colors, styles and products. Consult your local

distributor for ﬁreplace code information.

1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

INSTALLATION INSTRUCTIONS

NOTE: Shroud kit installation does not require the removal of the square

termination.

Step 1. Turn off the ﬁreplace and allow the termination to cool before

proceeding.

Step 2. Loosen the four (4) screws on the existing square termination

(refer to Figure 2).

Step 3. Slide the body of the shroud over the termination screws that

have been loosened, setting it in place (refer to Figure 2).

Step 4. Re-tighten the four (4) screws into place, securing the shroud

body over the termination.

Step 5. Position the shroud top over the shroud body and screw it into

the ﬂanges located on both the shroud top and shroud body,

using ﬁve (5) screws (as shown in Figure 2).

NOTE: The ﬁve (5) screws are to be attached from the bottom.

Step 6. Attach the bottom screen onto the body of the shroud, using the

three (3) screws into each of the three ﬂanges on the shroud

body (see Figure 2 ).

Step 7. If desired, paint shroud to any color.

Astria Fireplaces Merit Louverless Instruction Sheet

Astria Fireplaces Merit Louverless Instruction Sheet

Astria Fireplaces Merit Louverless Instruction Sheet

Related papers

Other documents